Search

The friction stir welding (FSW) process is a unique combination of deformation and high temperature, which provides opportunities to modify microstructures through the adjustment of the processing parameters and is an ideal way to join non-weldable aluminum alloys by avoiding the formation of a molten pool. The 7xxx series heat-treatable aluminum alloys are widely used in the aerospace field as high-performance structural materials. The microstructure evolution and mechanical performance of these alloys are affected by the effects of thermomechanical processing, which provides opportunities to optimize the material properties by controlling microstructural features such as intermetallic constituent particles, dispersoids and nanoscale precipitates. This paper focuses on the basic principles of the thermal and mechanical effects generated during FSW on the evolution of second-phase particles in different zones of the weld. [ABSTRACT FROM AUTHOR]

The influence of Si content (0.1–0.8 wt.%) on the development of precipitation microstructures and the resultant mechanical and creep properties during thermal exposure, up to 1000 h at 300 °C, in Al–Cu 224 cast alloys, was systematically investigated. The room and elevated temperature yield strength (YS) increased with increasing Si content under the T7 condition, which was attributed to the fact that the Si promoted the precipitation of fine θ′. However, Si increased the coarsening of θ′ during thermal exposure at 300 °C, and the alloys with low Si exhibited a higher YS and creep resistance at elevated temperatures than high Si alloys. The mechanical strength and creep resistance were mainly controlled by the precipitation strengthening of the predominant θ′ phase. Because of the high mechanical strength and creep resistance of the 0.1Si alloy during long-term thermal exposure, the Si level in Al–Cu alloys should be maintained at a low level of 0.1 wt.% for high-temperature applications. The strengthening mechanisms were quantitatively analyzed, based on the characteristics of the precipitate. The predicted YS values under different exposure conditions agreed well with the experimentally measured values. [ABSTRACT FROM AUTHOR]

Landslides are common geological hazards that cause significant losses. Anti-slide piles are commonly used in landslide engineering, and model testing is one of the means to study pile-supported structures. However, model tests face several challenges, including difficulty in controlling the experimental process, challenges in repeated tests, and difficulty in monitoring soil deformation around piles. To address these issues, this study presents a model test method using particle image velocimetry (PIV), transparent soil, and 3D printing technology. Using this method, a series of model tests were conducted, including single-row and double-row anti-slide piles. The experimental results indicate that, compared with single-row piles, double-row piles exhibit better supporting effects. In the pile‒soil interaction, the displacement of the extrusion of soil between piles was controlled under the combined action of the front and back rows of piles. The inclination angle of a single-row pile after the test was 8°, whereas that of a double-row pile was reduced by 62.5%. With respect to the displacement of the soil behind the piles, the phenomenon of a "displacement triangle" behind the piles was observed. An analysis of the change process in this area revealed that the relative displacement caused by pile‒soil interactions is mainly distributed in the surface layer of the soil. The experiments demonstrate that this system is suitable for pile-supported structure model tests. [ABSTRACT FROM AUTHOR]

Accurate characterization of soil hydraulic conductivity influenced by temperature under a centrifugal environment is important for hydraulic and geotechnical engineering. Therefore, a temperature-influenced scaling law for hydraulic conductivity of soil in centrifuge modeling was deduced, and a temperature-controlled falling-head permeameter apparatus specifically designed for centrifuge modeling was also developed. Subsequently, a series of temperature-controlled falling-head tests were conducted under varying centrifugal accelerations to achieve the following objectives: (1) examine the performance of the apparatus, (2) investigate the influence of temperature and centrifugal acceleration on the hydraulic conductivity of sand and its scaling factor, and (3) validate the proposed scaling law for hydraulic conductivity. The main conclusions of the study are as follows. Firstly, the apparatus demonstrated good sealing and effectively controlled the temperature of both the soil specimen and the fluid. Secondly, the hydraulic conductivity of sand was not constant but varied over time, likely due to the presence of radial seepage in addition to vertical seepage as the test progressed. Thirdly, temperature significantly influenced the hydraulic conductivity of sand and its scaling factor under the same centrifugal acceleration. Therefore, it is essential to closely monitor the temperature of models during centrifugal tests. Finally, the measured and calculated values of the scaling factor index for the hydraulic conductivity of sand showed good agreement, verifying the proposed scaling law. [ABSTRACT FROM AUTHOR]

For materials with high stacking fault energy (SFE), such as aluminum alloys, dynamic recovery (DRV) and dynamic recrystallization (DRX) are essential softening mechanisms during plastic deformation, which lead to the continuous generation and refinement of newborn subgrains (2° ˂ misorientation angle ˂ 15°). The present work investigates the influence of compression parameters on the evolution of the substructures for a 1050 aluminum alloy at elevated temperatures. The alloy microstructure was investigated under deformation temperatures ranging from 300 °C to 500 °C and strain rates from 0.01 to 0.1 s−1, respectively. A well-defined substructure and subsequent subgrain refinement provided indication of the evolution laws of the substructure under high-temperature compression. Corresponding experimental data on the average subgrain size under various compression conditions were obtained. Two different independent average subgrain size evolution models (empirical and substructure-based) were used and applied with several internal state variables. The substructure model employed physical variables to simulate subgrain refinement and thermal coarsening during deformation, incorporating a corresponding dislocation density evolution model. The correlation coefficient (R) and root mean square error (RMSE) of the substructure-based model were calculated to be 0.98 and 5.7%, respectively. These models can provide good estimates of the average subgrain size, with both predictions and experiments reproducing the expected subgrain size evolution using physically meaningful variables during continuous deformation. [ABSTRACT FROM AUTHOR]

Microbial degradation represents an eco-friendly alternative to traditional physicochemical treatments in removing persistent and toxic environmental pollutants, including synthetic dyes (i.e., methylene blue, MB) employed in different industries. The exploitation of thermophilic bacilli, such as those isolated from the shallow hydrothermal vents of the Eolian Islands (Italy), could provide valuable resources for the treatment of warm, dye-containing wastewater. In this study, we evaluated the ability of preformed biofilms on polypropylene perforated balls (BBs) of fifteen thermophilic bacilli, to decolor, degrade, and detoxify MB in aqueous solutions. Among them, BBs of Bacillus licheniformis B3-15 and Bacillus sp. s7s-1 were able to decolorize MB more than 50% in saline solution (NaCl 2%), incubated in static conditions at 45 °C for 48 h. At optimized initial conditions (10 mg L−1 MB, pH 5.2 for B3-15 or pH 4 for s7s-1), the two strains enhanced their decolorization potential, reaching 96% and 67%, respectively. As indicated by ATR-FTIR spectroscopy, the treatment with BB B3-15 was the most efficient in degrading the Cl–C and –NH groups of MB. This degraded solution was 40% less toxic than undegraded MB, and it has no impact on the bioluminescence of Vibrio harveyi, nor the growth of the marine diatom Phaeodactylum tricornutum. Biofilm formed by strain B3-15 on polypropylene perforated balls could be proposed as a component of bioreactors in the treatment of warm, dye-containing wastewater to concomitantly remediate MB pollution and simultaneously counteract harmful effects in aquatic environments. [ABSTRACT FROM AUTHOR]

Understanding the role of iron in ethanol-derived hepatic stress could help elucidate the efficacy of dietary or clinical interventions designed to minimize liver damage from chronic alcohol consumption. We hypothesized that normal levels of iron are involved in ethanol-derived liver damage and reduced dietary iron intake would lower the damage caused by ethanol. We used a pair-fed mouse model utilizing basal Lieber-DeCarli liquid diets for 22 weeks to test this hypothesis. In our mouse model, chronic ethanol exposure led to mild hepatic stress possibly characteristic of early-stage alcoholic liver disease, seen as increases in liver-to-body weight ratios. Dietary iron restriction caused a slight decrease in non-heme iron and ferritin (FeRL) expression while it increased transferrin receptor 1 (TfR1) expression without changing ferroportin 1 (FPN1) expression. It also elevated protein lysine acetylation to a more significant level than in ethanol-fed mice under normal dietary iron conditions. Interestingly, iron restriction led to an additional reduction in nicotinamide adenine dinucleotide (NAD+) and NADH levels. Consistent with this observation, the major mitochondrial NAD+-dependent deacetylase, NAD-dependent deacetylase sirtuin-3 (SIRT3), expression was significantly reduced causing increased protein lysine acetylation in ethanol-fed mice at normal and low-iron conditions. In addition, the detection of superoxide dismutase 1 and 2 levels (SOD1 and SOD2) and oxidative phosphorylation (OXPHOS) complex activities allowed us to evaluate the changes in antioxidant and energy metabolism regulated by ethanol consumption at normal and low-iron conditions. We observed that the ethanol-fed mice had mild liver damage associated with reduced energy and antioxidant metabolism. On the other hand, iron restriction may exacerbate certain activities of ethanol further, such as increased protein lysine acetylation and reduced antioxidant metabolism. This metabolic change may prove a barrier to the effectiveness of dietary reduction of iron intake as a preventative measure in chronic alcohol consumption. [ABSTRACT FROM AUTHOR]

The heat-aging process, a practical aging technology that not only improves the comprehensive performance of Al alloys but also reflects the requirements of short processes, has an extremely practical significance. The effects of the heating rate and termination temperature on the "heat-aging" behavior of a spray-deposited AlZnMgCu alloy hot-extruded plate were investigated using hardness, electrical conductivity, room-temperature tensile strength, exfoliation corrosion experiments, and transmission electron microscopy microstructure (TEM) observation. The results show that as the termination temperature increases, the hardness of the spray-deposited AlZnMgCu alloy first increases to a peak and then rapidly decreases, while the electrical conductivity continues to increase. The increase in the heating rate improves the peak hardness corresponding to the termination temperature. The heat treatment process of heating at a speed of 20 °C/h to 200 °C after the spray deposition has similar mechanical and corrosion resistance properties to the RRA process and can effectively reduce the heating time from 40 h to 8 h, thus establishing a heat treatment process for spray-deposited AlZnMgCu alloy extruded plate with high aging efficiency. [ABSTRACT FROM AUTHOR]

Continuous dynamic recrystallization (CDRX) forms a new recrystallized microstructure through the progressive increase in low-angle boundary misorientations (LAGBs) during the hot forming of metallic materials with high stacking fault energy (SFE), such as aluminum alloys. The present work investigates the effect of deformation parameters on the evolution of the dynamic recrystallization microstructures of an AA1050 aluminum alloy during compression at elevated temperatures. The alloy microstructure is investigated at deformation temperatures and strain rates in the range of 300 °C to 500 °C and 0.001 to 0.8 s−1. A well-defined substructure and subsequent DRX grains provide indication that recrystallization can proceed with continued strain under high-temperature compression. At a strain rate of 0.1 s−1, the DRX fraction is observed to be 0.25 at a temperature of 300 °C. This fraction increases to 0.32 as the temperature rises to 400 °C. The recrystallization mechanism is identified by analyzing the flow stress, the evolution of the subgrain misorientation angle, and the distribution of recrystallized grains. The observations of discontinuous dynamic recrystallization (DDRX) and CDRX under various deformation parameters are discussed. Moreover, the main substructure evolution laws observed from the high-temperature compression of an AA1050 Al alloy are summarized. [ABSTRACT FROM AUTHOR]

The effects of Sc, Mg and Si elements in an Al-Cu alloy have been studied by means of hardness tests and transmission electron microscopy analysis. The experimental results show that additions of Sc, Mg and Si can improve the heat resistance of the Al-Cu alloy. The Sc/Mg/Si segregation-sandwiched structure is the most stable, when compared with Sc segregation or Si/Sc co-segregation at the interface of θ′/Al. The additions of Si and Mg promote the aging–hardening response of the Al-Cu alloy. Mg is a micro-alloying element with great potential in stabilizing the size of θ′ phases, which further promotes the number density greatly. Consequently, the Al-Cu alloy achieves a high strength, matched with excellent thermal stability, due to the microalloying of Sc/Mg/Si solutes. [ABSTRACT FROM AUTHOR]

It is meaningful to monitor and identify concrete cracks as they will seriously reduce the fatigue life of pavement. In this paper, a new method based on distributed long-gauge optic fiber sensing is proposed to implement crack identification. Firstly, the damage indicator, namely strain curve envelope area ratio (SCEAR), is proposed and calculated with the measured strain in time series when the plane goes across the pavement where the sensors are installed. Then, the indicators with different sensors are normalized by the value of the indicator from one referenced sensor where damage normally will not happen. If the crack happens within the sensing gauge of the sensor, the value of the damage indicator SCEAR from the sensor will increase. Therefore, the crack will be identified with the change of the damage indicator. The effect of the proposed method is first verified by some simulations of prefabricated pavement as the cracks can be accurately identified by the proposed method. Moreover, the influence of the aircraft, such as taxiing position, aircraft load, and aircraft type, is not obvious enough to mislead the identification results. Lastly, the static loading tests were implemented with one small-scale model of prefabricated concrete pavement in the lab. From the experimental results, the prefabricated cracks inside the pavement slab can be identified accurately with the proposed method as the parameter SCEAR is increased by about 100% at the crack position, while it is only changed by about 3% at the undamaged position. [ABSTRACT FROM AUTHOR]

As an anti-staling agent in bread, the desorption isotherm of polydextrose has not been studied due to a very long equilibrium time. The adsorption and desorption isotherms of five Chinese polydextrose products were measured in the range of 0.1–0.9 aw and 20–35 °C by a dynamic moisture sorption analyzer. The results show that the shape of adsorption and desorption isotherms was similar to that of amorphous lactose. In the range of 0.1–0.8 aw, the hysteresis between desorption and adsorption of polydextrose was significant. The sorption isotherms of polydextrose can be fitted by seven commonly used models, and our developed seven-parameter polynomial, the adsorption equations of generalized D'Arcy and Watt (GDW) and Ferro-Fontan, and desorption equations of polynomial and Peleg, performed well in the range of 0.1–0.9 aw. The hysteresis curves of polydextrose at four temperatures quickly decreased with aw increase at aw ˂ 0.5, andthereafter slowly decreased when aw ≥ 0.5. The polynomial fitting hysteresis curves of polydextrose were divided into three regions: ˂0.2, 0.2–0.7, and 0.71–0.9 aw. The addition of 0–10% polydextrose to rice starch decreased the surface adsorption and bulk absorption during the adsorption and desorption of rice starch, while it increased the water adsorption value at aw ≥ 0.7 due to polydextrose dissolution. DSC analysis showed that polydextrose as a gelling agent inhibited the retrogradation of rice starch, which could be used to maintain the quality of cooked rice. [ABSTRACT FROM AUTHOR]

In industrial production and water resource management involving fluid flows, two-phase flow measurement in complex environments has always been a research hotspot. In this study, a broadband detection device (40–110 MHz) suitable for two-phase flow in pipes was designed in a laboratory environment, the impedance response of two-phase flow was investigated under different salinity conditions and flow patterns, and a new impedance dispersion model suitable for two-phase flow in pipes was built. The experimental results show that the new model can better describe the rules of impedance dispersion in two-phase flow and is universally applicable, and that the equivalent solution resistance and interfacial polarization frequency have a stable functional relationship with water holdup. Based on the static experimental results, water holdup evaluation models for four flow patterns were established, and the dynamic detection results were predicted. The prediction results show that the new method proposed herein is not affected by changes in salinity and flow pattern when the flow pattern is known, and that its accuracy can meet the production requirements. This study expands the application range of traditional single-frequency conductivity detection techniques and provides a new idea for the development and improvement of systems for online detection of water holdup in two-phase flow. [ABSTRACT FROM AUTHOR]

In light of the post-genomic era, epigenetics brings about an opportunity to better understand how the molecular machinery works and is led by a complex dynamic set of mechanisms, often intricate and complementary in many aspects. In particular, epigenetics links developmental biology and genetics, as well as many other areas of knowledge. The present work highlights substantial scopes and relevant discoveries related to the development of the term from its first notions. To our understanding, the concept of epigenetics needs to be revisited, as it is one of the most relevant and multifaceted terms in human knowledge. To redirect future novel experimental or theoretical efforts, it is crucial to compile all significant issues that could impact human and ecological benefit in the most precise and accurate manner. In this paper, the reader can find one of the widest compilations of the landmarks and epistemic considerations of the knowledge of epigenetics across the history of biology from the earliest epigenetic formulation to genetic determinism until the present. In the present work, we link the current body of knowledge and earlier pre-genomic concepts in order to propose a new definition of epigenetics that is faithful to its regulatory nature. [ABSTRACT FROM AUTHOR]

This study systematically investigates the energy and electronic properties of Si-segregated θ′(Al2Cu)/Al semi-coherent and coherent interface systems in Al-Cu alloys using ab initio calculations. By evaluating the bonding strength at the interface, it has been revealed that Si segregated at the A1 site (Al slab) of the semi-coherent interface systems exhibits the most negative segregation energy, resulting in a noticeable decrease in total energy and an increase in interface adhesion. The electronic structure analysis indicates the presence of Al-Cu and Al-Al bonds, with Si occupying the A1 site. The strong bond formation between Al-Cu and Al-Al is essential for improving interface bonding strength. The results of the calculating analyses are consistent with the results of the previous experiments, and Si can be used as a synergistic element to reduce the θ′/Al interface energy and further reduce the coarsening drive of the θ′ precipitated phase, which can provide new perspectives and computational ideas for the compositional design of heat-resistant Al-Cu alloys. [ABSTRACT FROM AUTHOR]

Background: The study aimed to examine the bidirectional relationship between sarcopenia and depressive symptoms in a national, community-based cohort study, despite the unclear temporal sequence demonstrated previously. Methods: Data were derived from four waves (2011 baseline and 2013, 2015, and 2018 follow-ups) of the China Health and Retirement Longitudinal Study (CHARLS). A total of 17,708 participants aged 45 years or older who had baseline data on both sarcopenia status and depressive symptoms in 2011 were included in the study. For the two cohort analyses, a total of 8092 adults without depressive symptoms and 11,292 participants without sarcopenia in 2011 were included. Sarcopenia status was defined according to the Asian Working Group for Sarcopenia 2019 (AWGS 2019) criteria. Depressive symptoms were defined as a score of 20 or higher on the 10-item Center for Epidemiologic Studies Depressive Scale (CES-D-10). Cox proportional hazard regression models were conducted to examine the risk of depressive symptoms and sarcopenia risk, while cross-lagged panel models were used to examine the temporal sequence between depressive symptoms and sarcopenia over time. Results: During a total of 48,305.1 person-years follow-up, 1262 cases of incident depressive symptoms were identified. Sarcopenia exhibited a dose–response relationship with a higher risk of depressive symptoms (HR = 1.7, 95%CI: 1.2–2.3 for sarcopenia, and HR = 1.5, 95%CI: 1.2–1.8 for possible sarcopenia, p trend < 0.001). In the second cohort analysis, 240 incident sarcopenia cases were identified over 39,621.1 person-years. Depressive symptoms (HR = 1.5, 95%CI: 1.2–2.0) are significantly associated with a higher risk of developing sarcopenia after multivariable adjustment (p < 0.001, Cross-lagged panel analyses demonstrated that depressive symptoms were associated with subsequent sarcopenia (β = 0.003, p < 0.001). Simultaneously, baseline sarcopenia was also associated with subsequent depressive symptoms (β = 0.428, p < 0.001). Conclusion: This study identified a bidirectional relationship between depressive symptoms and sarcopenia. It seems more probable that baseline sarcopenia is associated with subsequent depressive symptoms in a stronger pattern than the reverse pathway. The interlinkage indicated that maintaining normal muscle mass and strength may serve as a crucial intervention strategy for alleviating mood disorders. [ABSTRACT FROM AUTHOR]

This paper reviews the relevant literature and covers the main aspects of the environmentally assisted cracking of Al-Mg-Si-(Cu) alloys. Apart from a brief overview of the major microstructural and mechanical properties, it presents research results on the corrosion sensitivity and stress corrosion susceptibility of Al-Mg-Si alloys. Possible mechanisms of stress corrosion cracking and corrosion fatigue in aluminum alloys, such as anodic dissolution and/or interaction with hydrogen, are considered. A number of factors, including atmospheric or solution conditions, applied stress, and material properties, can affect these mechanisms, leading to environmentally assisted cracking. Specific attention is given to Al-Mg-Si alloys with copper, which may increase the sensitivity to intergranular corrosion. The susceptibility to both intergranular corrosion and stress corrosion cracking of Cu-containing Al-Mg-Si alloys is mostly associated with a very thin layer (segregation) of Cu on the grain boundaries. However, the effect of Cu on the corrosion fatigue and fatigue crack growth rate of Al-Mg-Si alloys has received limited attention in the literature. At the current state of the research, it has not yet been holistically assessed, although a few studies have shown that a certain content of copper can improve the resistance of aluminum alloys to the environment with regard to corrosion fatigue. Furthermore, considerations of the synergistic actions of various factors remain essential for further studying environmentally assisted cracking phenomena in aluminum alloys. [ABSTRACT FROM AUTHOR]

Here, 0.3 wt.%Zr was introduced in an Al-4 wt.%Cu-0.5 wt.%Mn-0.1 wt.%Fe alloy to investigate its influence on the microstructure and mechanical properties of the alloy. The microstructures of both as-cast and T6-treated Al–Cu–Mn–Fe (ACMF) and Al–Cu–Mn–Fe–Zr (ACMFZ) alloys were analyzed. The intermetallic compounds formed through the casting procedure include Al2Cu and Al7Cu2Fe, and the Al2Cu phase dissolves into the matrix and re-precipitates as θ′ phase during the T6 process. The introduction of Zr results in the precipitation of L12-Al3Zr nanometric precipitates after T6, while the θ′ precipitates in ACMFZ alloy are much finer than those in ACMF alloy. The L12-Al3Zr precipitates were found coherently located with θ′, which was assumed beneficial for stabilizing the θ′ precipitates during the high-temperature tensile process. The tensile properties of ACMF and ACMFZ alloys at room temperature and elevated temperatures (200, 300, and 400 °C) were tested. Especially, the yield strength of ACMFZ alloys can reach 128 MPa and 65 MPa at 300 °C and 400 °C, respectively, which are 31% and 33% higher than those of ACMF alloys. The strengthening mechanisms of grain size, L12-Al3Zr, and θ′ precipitates on the tensile properties were discussed. This work may be referred to for designing Al–Cu alloys for application in high-temperature fields. [ABSTRACT FROM AUTHOR]

Retrogression and re-aging (RRA) treatment has been proven to effectively overcome the trade-off between strength and corrosion resistance. Current research focuses on the heating rate, temperature, and holding time of retrogression treatment while ignoring the retrogression cooling ways. In this paper, the effects of RRA treatment with different retrogression cooling ways on the microstructure and properties of newly developed T'/η' strengthened Al-Zn-Mg-Cu alloys were investigated by performing tests on mechanical properties, intergranular corrosion (IGC) resistance, and electrochemical corrosion behavior. The results show that the mechanical properties of samples subject to RRA treatment with water-quenching retrogression (ultimate tensile strength, yield strength, and elongation of 419.2 MPa, 370.2 MPa, and 15.9, respectively) are better than those of air-cooled and furnace-cooled samples. The corrosion resistance of water-quenching (IGC depth of 162.2 μm, corrosion current density of 0.833 × 10−5 A/cm2) and furnace-cooled samples (IGC depth of 123.7 μm, corrosion current density of 0.712 × 10−5 A/cm2) is better than that of air-cooled samples. Microstructure characterization reveals that the effect of the retrogression cooling rate on mechanical properties is related to the size of T'/η' precipitates with grains as well as the proportion of T' and η', while the difference in corrosion resistance depends on the continuity of grain boundary precipitates (GBPs). With mechanical properties, corrosion resistance, and time cost taken into consideration, it is appropriate to select water quenching for retrogression. These findings offer valuable insights for further design to achieve superior performance in various applications. [ABSTRACT FROM AUTHOR]

The mechanical properties of metastable β-titanium alloys are highly susceptible during the thermal mechanical processing (TMP). In this process, the recrystallization process plays an important role in determining the microstructure and texture evolution. The implementation of dynamic recrystallization (DRX), a process for achieving β-grain refinement, is considered of great significance for the improvement of the properties of metastable β-titanium alloys and their industrial production. Along these lines, in this work, an isothermal compression test of TB8 titanium alloy was carried out by using a Gleeble-3500 thermal simulator. As a result, the rheological stress behavior was analyzed, the thermal processing map was accurately established based on the stress–strain curve, and the optimal processing interval was determined. The DRX kinetic and the DRX grain size models were developed, on the basis of which a new DRX intrinsic model was established to improve the material parameters. Therefore, the actual situation in the working process could be better predicted. The microstructural evolution of TB8 titanium alloy during thermal deformation was comprehensively investigated using the electron backscatter diffraction (EBSD) technique. The obtained results demonstrate a close correlation between the diversity of DRX mechanisms in TB8 alloy and the distribution of dislocation density. Four microstructural textures during thermal deformation were identified, in which the cube texture of (001) <010> and the R-Gorss Nd texture of (110) <110> dominate. Due to the random orientation of the dynamically recrystallized grains, the strength of the R-Gorss Nd texture of (110) <110> increases with the increase in the volume fraction of DRX. On the contrary, it was verified that the dynamic recrystallization behavior has a significant weakening impact on the cube texture of (001) <010>. [ABSTRACT FROM AUTHOR]

Royal jelly is a secretion produced from the hypopharyngeal glands of worker bees, which requires significant pollen reserves to stimulate gland secretion. The natural sources of food available to the hive during beekeeping season can greatly affect the quantity and quality of produced royal jelly. In this study, samples of royal jelly were collected throughout the beekeeping season, and their physical and chemical characteristics were analyzed to understand how natural variations in bee diet affect royal jelly production. Before each sample collection, the bees' food reserves were removed from the experimental colonies so that the royal jelly was produced solely from natural sources. The results showed that the production was significantly lower during the summer months compared with spring and autumn. Additionally, the moisture, protein, fructose, and glucose content of fresh royal jelly also showed significant changes in the summer, and all physical and chemical characteristics decreased when the fresh samples were converted into dry matter. It seems that the quality of pollen entering the hives has a direct impact on the physical and chemical properties of the final product, highlighting the crucial role of available resources in stimulating bees to produce royal jelly. [ABSTRACT FROM AUTHOR]

Spray forming is a manufacturing process that enables the production of high-performance metallic materials with exceptional properties. Due to its rapid solidification nature, spray forming can produce materials that exhibit fine, uniform, and equiaxed microstructures, with low micro-segregation, high solubility, and excellent workability. Al-Zn-Mg-Cu alloys have been widely used in the aerospace field due to their excellent properties, i.e., high strength, low density, and outstanding machinability. The alloy manufactured by spray forming has a combination of better impact properties and higher specific strength, due to its higher cooling rate, higher solute concentration, and lower segregation. In this manuscript, the recent development of spray-formed Al-Zn-Mg-Cu alloys is briefly reviewed. The influence of hot working, i.e., hot extrusion, hot forging, and hot rolling, as well as different heat treatments on the property and microstructure of spray-formed Al-Zn-Mg-Cu alloys is introduced. The second phases and their influence on the microstructure and mechanical properties are summarized. Finally, the potential in high-temperature applications and future prospects of spray-formed aluminum alloys are discussed. [ABSTRACT FROM AUTHOR]

This paper mainly investigated the effect of the Mn/Ag ratio on the microstructure and room temperature and high-temperature (350 °C) tensile mechanical properties of the as-cast and heat-treated Al-6Cu-xMn-yAg (x + y = 0.8, wt.%) alloys. The as-cast alloy has α-Al, Al2Cu, and a small amount of Al7Cu2 (Fe, Mn) and Al20Cu2 (Mn, Fe)3 phases. After T6 heat treatment, a massive dispersive and fine θ′-Al2Cu phase (100~400 nm) is precipitated from the matrix. The Mn/Ag ratio influences the quantity and size of the precipitates; when the Mn/Ag ratio is 1:1, the θ′-Al2Cu precipitation quantity reaches the highest and smallest. Compared with the as-cast alloy, the tensile strength of the heat-treated alloy at room temperature and high temperature is greatly improved. The strengthening effect of the alloy is mainly attributed to the nanoparticles precipitated from the matrix. The Mn/Ag ratio also affects the high-temperature tensile mechanical properties of the alloy. The high-temperature tensile strength of the alloy with a 1:1 Mn/Ag ratio is the highest, reaching 135.89 MPa, 42.95% higher than that of the as-cast alloy. The analysis shows that a synergistic effect between Mn and Ag elements can promote the precipitation and refinement of the θ′-Al2Cu phase, and there is an optimal ratio (1:1) that obtains the lowest interfacial energy for co-segregation of Mn and Ag at the θ′/Al interface that makes θ′-Al2Cu have the best resistance to coarsening. [ABSTRACT FROM AUTHOR]

Al-based foams have drawn increasing attention from industry due to their integration of structure and functional properties. However, large-sized Al-based foams still cannot be homogeneously strengthened by long-time aging due to their low thermal conductivity. In this study, we proposed an age-hardening approach that was applied in large-sized Al-0.16Sc-0.17Zr (wt.%) foams via micro-alloying with Zr and Ti compared with Al-0.21Sc foams; it not only achieved homogeneous strength by long-term aging but also reduced the cost of the alloy by substituting Zr and Ti for the more expensive Sc content. The results show that the Al3(Sc, Zr, Ti) phase with a core–shell structure as a crucial precipitation strengthening phase by micro-alloying with Zr and Ti was less prone to coarsening after a prolonged aging heat treatment. Therefore, the yielding strength of Al-Sc foam micro-alloying with Zr and Ti remained almost unchanged after a maximum aging time of 1440 h due to less coarsening precipitate, which is consistent with the results of mechanical experiments. These findings provide a new way for the heat treatment strengthening of large-sized Al-based foams, thus promoting their industrial applications. [ABSTRACT FROM AUTHOR]

In this paper, the urban signal propagation characteristics based on the location of blind sources are investigated. To address the issue of blind electromagnetic radiation sources in complex urban environments, intelligent methods for propagation channel path classification, and model determination are brought forth based on field test data. The intelligent classification method distinguishes between the Line-of-Sight (LoS) path channel and a direct path, the LoS multipath channel with a direct path and other multiple paths, and the Non-Line-of-Sight (NLoS) multipath channel without a direct path from the source to the test point. The modeling aspect determines the model type to which the received signal belongs based on the statistical model derived from the tested data of a specific source. A validation measurement system was constructed for the FM broadcasting band, and validation campaigns were conducted in the city of Wuhan. The process and analysis of the data using this method demonstrate the accurate distinction of the different propagation path channels and models and involve the construction of a statistical model for the FM band in Wuhan's urban area. [ABSTRACT FROM AUTHOR]

Apple is an important cash crop in China, and it is susceptible to fungal infections that have deleterious effects on its yield. Apple bitter rot caused by Colletorichum gloeosporioides is one of the most severe fungal diseases of apple. Salicylic acid (SA) is a key signalling molecule in the plant disease resistance signalling pathways. Lignin synthesis also plays a key role in conferring disease resistance. However, few studies have clarified the relationship between the SA disease resistance signalling pathway and the lignin disease resistance pathway in apple. MdMYB46 has previously been shown to promote lignin accumulation in apple and enhance salt and osmotic stress tolerance. Here, we investigated the relationship between MdMYB46 and biological stress; we found that MdMYB46 overexpression enhances the resistance of apple to C. gloeosporioides. We also identified MdARF1, a transcription factor upstream of MdMYB46, via yeast library screening and determined that MdARF1 was regulated by miR7125 through psRNATarget prediction. This regulatory relationship was confirmed through LUC and qRT-PCR experiments, demonstrating that miR7125 negatively regulates MdARF1. Analysis of the miR7125 promoter revealed that miR7125 responds to SA signals. The accumulation of SA level will result in the decrease of miR7125 expression level. In sum, the results of our study provide novel insights into the molecular mechanisms underlying the resistance of apple to C. gloeosporioides and reveal a new pathway that enhances lignin accumulation in apple in response to SA signals. These findings provide valuable information for future studies aimed at breeding apple for disease resistance., (© 2024 The Author(s). Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.)

Dislocation slips, twinning, shear banding (SBs), strain localization, and martensite formation are a few deformation modes that are activated in BCC metals and alloys. Strain, strain rate, and deformation temperature are other parameters that determine the activation of deformation modes in BCC alloys. This review focuses on several BCC alloys, such as beta-titanium (β-Ti), tantalum (Ta), and ferritic stainless steels (FSSs), all of which exhibit differences in deformation behavior. These alloys often undergo thermo-mechanical processing (TMP) to enhance their mechanical properties. TMP leads to the evolution of deformation-induced products, such as SBs, strain-induced martensite (SIM), strain localizations, and mechanical/deformation twins (DTs) during plastic deformation, while also influencing crystallographic texture. The deformation modes in β-Ti depend upon the stability of the β-phase (i.e., β-stabilizers); low-stability alloys show the formation of SIM along with slips and twins, whereas in highly stable β-Ti alloys, only slip+twin modes are observed as the primary deformation mechanisms. In the case of Ta, slip activity predominantly occurs on {110} planes, but it can also occur on planes with the highest resolved shear stress. The breakdown of Schmid's law or non-Schmid behavior for Ta and Ta-W alloys has been discussed in detail. The cold rolling (CR) of FSSs results in the formation of ridges, which is an undesirable phenomenon leading to very low formability. The microstructures of the rolled sheets consist of elongated ferrite grains with in-grain SBs, which are preferentially formed in the γ-fiber-oriented grains. The formation of finer grains after recrystallization improves both the mechanical properties and ridging resistance in FSS. Therefore, this review comprehensively reports on the impact of TMP on the microstructural and crystallographic texture evolution during the plastic deformation and annealing treatment of β-Ti, Ta alloys, and FSSs in BCC materials, using results obtained from electron microscopy and X-ray diffraction. [ABSTRACT FROM AUTHOR]

Artificial hybrid breeding can optimize parental traits to cultivate excellent hybrids with enhanced economic value. In this study, we investigated the growth performance and transcriptomes of Gymnocypris przewalskii (♀) and Gymnocypris eckloni (♂) and their F1 hybrid fishes. Hatched individuals of G. przewalskii (GP) and G. eckloni (GE) of the same size and their F1 hybrids (GH) were separately cultured for eight months in three cement tanks (n = 3). The growth indexes were measured, which showed that the growth rate of the groups was GE > GH > GP, while the survival rate was GH > GE > GP. The RNA-Seq data analysis of the muscles from the three Gymnocypris fish strains revealed that gene transcription has a significant impact on F1 hybrid fish and its parents. The differentially expressed genes (DEGs) in GH show less differences with GP, but more with GE. qRT-PCR was used to confirm the expression profiles of the chosen DEGs, and the results showed positive correlations with the RNA-seq data. KEGG enrichment results indicated that the DEGs were related to a variety of molecular functions, such as glycolysis/gluconeogenesis, arachidonic acid formation, citrate cycle, and the MAPK, PI3K-Akt, or mTOR signal pathways. Subsequent analysis indicated that there may be a significant correlation between the differential expression of IGF2 and a difference in the growth of GE and GP. [ABSTRACT FROM AUTHOR]

Acremonium fungi is one of the greatest and most complex genera in Hyphomycetes, comprising 130 species of marine and terrestrial sources. The past decades have witnessed substantial chemical and biological investigations on the diverse secondary metabolites from the Acremonium species. To date, over 600 compounds with abundant chemical types as well as a wide range of bioactivities have been obtained from this genus, attracting considerable attention from chemists and pharmacologists. This review mainly summarizes the sources, chemical structures, and biological activities of 115 recently reported new compounds from the genus Acremonium from December 2016 to September 2023. They are structurally classified into terpenoids (42%), peptides (29%), polyketides (20%), and others (9%), among which marine sources are predominant (68%). Notably, these compounds were primarily screened with cytotoxic, antibacterial, and anti-inflammatory activities. This paper provides insights into the exploration and utilization of bioactive compounds in this genus, both within the scientific field and pharmaceutical industry. [ABSTRACT FROM AUTHOR]

In order to increase the strength of Al-Zr alloys, which are promisingly used for heat-resistant conductors, the coupling effect of Mn addition (0.16 wt.% and 0.88 wt.%) and deformation on the precipitation, mechanical, and electrical properties of an Al-0.18wt.% Zr alloy was studied using transmission electron microscopy (TEM), atom probe tomography (APT), hardness testing, and electrical conductivity measurement, respectively. Results showed that the Mn addition fully suppresses the Al3Zr precipitation in both hot-deformed and undeformed cases, which is mainly due to a strong Mn-vacancy bonding, in which Mn atoms seize vacancies and hence reduce the available vacancies for Al3Zr nucleation. Minor 0.16 wt.% Mn addition causes a simultaneous decrease in hardness and electrical conductivity, regardless of whether there is deformation. The higher 0.88 wt.% Mn addition, however, significantly increases the hardness by over 40%, especially in combination with deformation. Possible influencing factors such as grain size, dislocations, intergranular/intragranular precipitation, and solute clusters are comparatively discussed in terms of microstructural features and mechanical/electrical properties that are tuned by Mn addition and/or deformation. It is found that the Mn addition can make remarkable contributions to the hardness and thermal stability of the Al-Zr alloys when coupled with deformation. [ABSTRACT FROM AUTHOR]

The hot tensile behavior of an extruded 6082 alloy sheet at varying temperatures and strain rates was investigated by a Gleeble3500 thermal simulation testing machine. The optical microscope (OM), scanning electron microscope (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) were applied to observe the microstructure evolution. It is found that the flow stress of the studied alloy declines with increasing deformation temperature. When deformed at high temperatures, the density of dislocation decreases obviously. In addition, precipitate coarsening occurs, resulting in a decrease in deformation resistance. The dimple number of the fracture samples increases with temperature and the size of the dimple becomes deeper, exhibiting an excellent plasticity. The 6082 sheet presents anisotropy of mechanical behavior at 300 °C, this can be attributed to the fibrous grain and the Brass component {011}<211>. The anisotropic behavior seems to be slighter with an increase in temperature. No obvious anisotropic behavior was found when tensiled at 400 °C. Because it is easier to activate the slip system at elevated temperatures, meanwhile, the recrystallization begins to occur at 400 °C. [ABSTRACT FROM AUTHOR]

In order to reinforce the mechanism of Ag in 5xxx aluminum alloys with low magnesium, research on the microstructure and mechanical properties of an Al-Mg-Mn-Ag-Cr-Zr alloy was conducted using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), hardness measurement, and tensile testing. The as-cast microscopic structure of the alloy comprises the Al6(Mn, Fe) phase and the T-Mg32(Al, Ag)49 phase. Changes in the characteristics of the investigated alloy were clear during the aging process. Based on the findings obtained from TEM and SAED analysis, it was evident that the predominant strengthening phase during the peak-aged stage is the β″ phase, observed when the alloy is aged for 24 h at 160 °C. The β″ phase had a L12-type crystal lattice architecture and presented a completely coherent relevance with the Al-matrix. The lattice parameter, a, of the β″ phase was 0.408 nm. The mechanical properties of the peak-aged alloy increased greatly as compared to the as-quenched alloy. The tensile strength exhibited a rise from 410 MPa to 449 MPa, representing a 9.5% increase, while the yield strength demonstrated an increase from 185 MPa to 273 MPa, indicating a significant enhancement of 47.5%. The method used in the present study has solved the problem of 5xxx aluminum alloys not being heat treatable for strengthening to a significant degree, considerably improving the alloy strength. In addition, new methods and foundations for exploiting new-type Al-Mg based alloys and developing high-strength aluminum alloys are provided in this study. [ABSTRACT FROM AUTHOR]

Abnormal sexual maturity exhibits significant detrimental effects on adult health outcomes, and previous studies have indicated that targeting histone acetylation might serve as a potential therapeutic approach to regulate sexual maturity. However, the mechanisms that account for it remain to be further elucidated. Using the mouse model, we showed that Trichostatin A (TSA), a histone deacetylase (HDAC) inhibitor, downregulated the protein level of Hdac1 in ovaries to promote the apoptosis of granulosa cells (GCs), and thus arrested follicular development and delayed sexual maturity. Using porcine GCs as a cell model, a novel sexual maturity-associated lncRNA, which was named as the stimulatory factor of follicular development (SFFD), transcribed from mitochondrion and mediated by HDAC1, was identified using RNA sequencing. Mechanistically, HDAC1 knockdown significantly reduced the H3K27ac level at the −953/−661 region of SFFD to epigenetically inhibit its transcription. SFFD knockdown released miR-202-3p to reduce the expression of cyclooxygenase 1 (COX1), an essential rate-limited enzyme involved in prostaglandin synthesis. This reduction inhibited the proliferation and secretion of 17β-estradiol (E2) while promoting the apoptosis of GCs. Consequently, follicular development was arrested and sexual maturity was delayed. Taken together, HDAC1 knockdown-mediated SFFD downregulation promoted the apoptosis of GCs through the miR-202-3p-COX1 axis and lead to delayed sexual maturity. Our findings reveal a novel regulatory network modulated by HDAC1, and HDAC1-mediated SFFD may be a promising new therapeutic target to treat delayed sexual maturity. [ABSTRACT FROM AUTHOR]

Simple Summary: Endoclita signifer (Lepidoptera, Hepialidae) poses a significant threat as a forestry pest to a diverse range of host plants. The gut microbiota of insects plays a pivotal role in establishing a symbiotic relationship with the host insect. Our research aims to scrutinize alterations in the gut microbiota and their correlation with distinct plant-feeding preferences, laying the groundwork for developing biological control strategies against E. signifer. We relocated E. signifer that had endured a period in Eucalyptus grandis × Eucalyptus urophylla to two different plant species, namely Mallotus apelta and Broussonetia papyrifera. Following a 4-week period, high-throughput sequencing was performed on the gut microbiota of moth larvae feeding on three plant species (E. grandis × E. urophylla, M. apelta, and B. papyrifera). The microbial composition in the E. signifer intestines exhibited similarities at the phylum level but disparities at the genus level. Concurrently, the E. signifer feeding preferences were predominantly linked to the nutritional composition of the plants. These findings imply that feeding preferences can impact the gut microbiota of E. signifer, with the nutritional composition of the plants emerging as a pivotal factor steering these preferences. This discovery introduces a novel perspective for the advancement of biological control techniques against E. signifer. Insects' gut microbiota plays a crucial role in their host selection, adaptation, and plasticity. This study explored the impact of gut bacteria on the adaptation of host selection under different stresses (diverse feeding preferences and no feeding preferences). The seventh instar E. signifer larvae were artificially transferred from the most-selected host E. grandis × E. urophylla (Es) to more preferred hosts, M. apelta (Ma), as well as the non-preferred host, B. papyrifera (Bp). We then obtained the larval gut of three different feeding preference hosts. The gut bacterial DNA was sequenced and analyzed based on 16S rRNA. There were significant differences in the composition of dominant gut bacteria between Es with Ma and Bp, but without significant differences between Ma and Bp. In the process, Burkholderia and Microbacillus with degrading pesticides had significant changes, and Enterococcus with insect gut probiotics also had significant changes. The presence of enterococcus may be one of the main causes of intestinal microbiota changes before and after host transfer. Notably, when the feeding of E. signifer changes, the complex connections that exist between gut bacteria also change. Additionally, there was a negative correlation between the feeding preferences of E. signifer and the metabolic functions of their gut bacteria. This study provided a theoretical basis for the prediction and use of gut bacteria to interfere with the feeding of E. signifer. [ABSTRACT FROM AUTHOR]

Autism spectrum disorder (ASD) prevalence is emerging with an unclear etiology, hindering effective therapeutic interventions. Recent studies suggest potential renin–angiotensin system (RAS) alterations in different neurological pathologies. However, its implications in ASD are unexplored. This research fulfills the critical gap by investigating dual arms of RAS and their interplay with Notch signaling in ASD, using a valproic acid (VPA) model and assessing astaxanthin's (AST) modulatory impacts. Experimentally, male pups from pregnant rats receiving either saline or VPA on gestation day 12.5 were divided into control and VPA groups, with subsequent AST treatment in a subset (postnatal days 34–58). Behavioral analyses, histopathological investigations, and electron microscopy provided insights into the neurobehavioral and structural changes induced by AST. Molecular investigations of male pups' cortices revealed that AST outweighs the protective RAS elements with the inhibition of the detrimental arm. This established the neuroprotective and anti-inflammatory axes of RAS (ACE2/Ang1-7/MasR) in the ASD context. The results showed that AST's normalization of RAS components and Notch signaling underscore a novel therapeutic avenue in ASD, impacting neuronal integrity and behavioral outcomes. These findings affirm the integral role of RAS in ASD and highlight AST's potential as a promising treatment intervention, inviting further neurological research implications. [ABSTRACT FROM AUTHOR]

The phase composition, microstructure, and mechanical properties of flat-rolled experimental Al-Cu-Mn system alloy with Si and Zr additions have been studied. The experimental results have been compared with data for the AA2219 commercial alloy pertaining to the same alloying system. Hot deformation of an experimental alloy causes the precipitation of ~100 nm sized dispersoids and refinement of the eutectic phase particles. The yield strength and relative elongation of the hot-deformed experimental alloy are 255 MPa and 8.6%, respectively. Subsequent cold deformation reduces the relative elongation by 3.5% and increases the yield strength by 50 MPa, while the ultimate tensile strength does not change. After long-term 350 °C exposure, the mechanical properties of the experimental alloy remain the same as those of the as-deformed one, whereas the yield strength of the 2219 alloy decreases by 2 times and the ultimate tensile strength by 1.4 times. Comparison of these experimental results with data for the 2219 alloy and other Al-Cu-Mn system alloys cited in this work and reported elsewhere suggests that a good thermal stability of Al-2Cu-2Mn-0.4Si-0.2Zr alloy rolled stock can be achieved through treatment using the regimes designed herein. [ABSTRACT FROM AUTHOR]

The effect of Mn content on the microstructure evolution and mechanical properties of Al–Cu–Mg–x Mn alloys at ambient temperature was investigated. The findings show that in the Mn-containing alloys at the as-cast state, the blocky primary T(Al20Cu2Mn3) phase coexisting with the Al2Cu phase appeared. With the increase in Mn content, the majority of the Al2Cu phase dissolved, nd a minor amount of the T phase remained at the grain boundary after solution treatment. The rod-like TMn (Al20Cu2Mn3) nanoprecipitate was simultaneously distributed at grain boundaries and the interiors, while a high density of needle-like θ″ (Al3Cu) nanoprecipitate was also observed in the T6 state. Further increases in Mn content promoted the dispersion of the TMn phase and inhibited the growth and transformation of the θ″ phase. Tensile test results show that 0.7 wt.% Mn alloy had excellent mechanical properties at ambient temperature with ultimate tensile strength, yield strength, and fracture elongation of 498.7 MPa, 346.2 MPa, and 19.2%, respectively. The subsequent calculation of strengthening mechanisms elucidates that precipitation strengthening is the main reason for the increase in yield strength of Mn-containing alloys. [ABSTRACT FROM AUTHOR]

Pulmonary fibrosis (PF) is a chronic interstitial lung disease characterized by myofibroblast abnormal activation and extracellular matrix deposition. However, the pathogenesis of PF remains unclear, and treatment options are limited. Epidemiological studies have shown that the average age of PF patients is estimated to be over 65 years, and the incidence of the disease increases with age. Therefore, PF is considered an age-related disease. A preliminary study on PF patients demonstrated that the combination therapy of the anti-senescence drugs dasatinib and quercetin improved physical functional indicators. Given the global aging population and the role of cellular senescence in tissue and organ aging, understanding the impact of cellular senescence on PF is of growing interest. This article systematically summarizes the causes and signaling pathways of cellular senescence in PF. It also objectively analyzes the impact of senescence in AECs and fibroblasts on PF development. Furthermore, potential intervention methods targeting cellular senescence in PF treatment are discussed. This review not only provides a strong theoretical foundation for understanding and manipulating cellular senescence, developing new therapies to improve age-related diseases, and extending a healthy lifespan but also offers hope for reversing the toxicity caused by the massive accumulation of senescence cells in humans. [ABSTRACT FROM AUTHOR]

Today, 7xxx aluminum alloys are widely used in aerospace and other fields due to their excellent properties such as low density, high specific strength, and good processing performance. The heat treatment process of 7xxx aluminum alloy is crucial in controlling the strengthening phases and grain size, which is a significant way to enhance the alloy's performance. In this study, solution heat treatment tests of 7050 aluminum alloys were carried out at different temperatures, ranging from 440 °C to 470 °C, with a holding time ranging from 0.5 h to 8 h, using a DIL 805A thermomechanical test machine. The microstructural evolution during the solution heat treatment was characterized using an optical microscope (OM), a scanning electron microscope (SEM), and a transmission electron microscope (TEM). The effects of the solution parameters on the alloy's microhardness were analyzed using a digital Vickers microhardness tester. According to the ASTM E112-13 standard, The Anelli grain growth models were established to illustrate the grain size evolution during solution heat treatment, and a modified Anelli grain growth model was established. The results indicated that the grain size significantly increases with the increase in the solution heat treatment time and temperature. The Anelli grain growth model can illustrate the phenomenon of grain growth more accurately in the solution heat treatment process of 7050 aluminum alloy. It was found that prolonging the time and elevating the temperature of the solution heat treatment reduced the microhardness of the aluminum alloy because of the dissolution of the precipitates. [ABSTRACT FROM AUTHOR]

This article conducts high-temperature creep tests on an Al-6.5Zn-2.3Mg-2.5Cu-0.1Zr-0.2Sc alloy in a solid solution + aging state at 200 °C and 150–180 MPa. Characterization of the microstructure of the specimen after creep test fracture was performed using SEM and TEM. The results indicate that the steady-state creep rate range of the alloy was 10−9 to 10−8 s−1, which was positively correlated with applied stress, while the creep life was negatively correlated with applied stress. Through failure analysis, it was found that the main deformation mechanism of the alloy was the dislocation climbing mechanism. The fracture mode of the alloy was ductile fracture. [ABSTRACT FROM AUTHOR]

In this paper, we studied the effects of a series of alloying atoms on the stability and micromechanical properties of aluminum alloy using a machine learning accelerated first-principles approach. In our preliminary work, high-throughput first-principles calculations were explored and the solution energy and theoretical stress of atomically doped aluminum substrates were extracted as basic data. By comparing five different algorithms, we found that the Catboost model had the lowest RMSE (0.24) and lowest MAPE (6.34), and this was used as the final prediction model to predict the solid solution strengthening of the aluminum matrix by the elements. Calculations show that alloying atoms such as K, Na, Y and Tl are difficult to dissolve in the aluminum matrix, whereas alloy atoms like Sc, Cu, B, Zr, Ni, Ti, Nb, V, Cr, Mn, Mo, and W exerted a strengthening influence. Theoretical studies on solid solutions and the strengthening effect of various alloy atoms in an aluminum matrix can offer theoretical guidance for the subsequent selection of suitable alloy elements. The theoretical investigation of alloy atoms in an aluminum matrix unveils the fundamental aspects of the solution strengthening effect, contributing significantly to the expedited development of new aluminum alloys. [ABSTRACT FROM AUTHOR]

High-temperature forming behaviors of a 7046-aluminum alloy were investigated by hot compression experiments. The microstructural evolution features with the changes in deformation parameters were dissected. Results indicated the formation of massive dislocation clusters/cells and subgrains through the intense DRV mechanism at low compression temperature. With an increase in deformation temperature, the annihilation of dislocations and the coarsening of subgrains/DRX grains became prominent, due to the collaborative effects of the DRV and DRX mechanisms. However, the growth of subgrains and DRX grains displayed the weakening trend at high strain rates. Moreover, two constitutive models involving a physically based (PB) model and a gate recurrent unit (GRU) model were proposed for predicting the hot compression features. By validation analysis, the predicted values of true stress perfectly fit with the experimental data, indicating that both the proposed PB model and the GRU model can accurately predict the hot compression behaviors of 7046-aluminum alloys. [ABSTRACT FROM AUTHOR]

The critical role of the DNA repair system in preserving the health and survival of living organisms is widely recognized as dysfunction within this system can result in a broad range of severe conditions, including neurodegenerative diseases, blood disorders, infertility, and cancer. Despite comprehensive research on the molecular and cellular mechanisms of DNA repair pathways, there remains a significant knowledge gap concerning these processes at an organismal level. The teleost zebrafish has emerged as a powerful model organism for investigating these intricate DNA repair mechanisms. Their utility arises from a combination of their well-characterized genomic information, the ability to visualize specific phenotype outcomes in distinct cells and tissues, and the availability of diverse genetic experimental approaches. In this review, we provide an in-depth overview of recent advancements in our understanding of the in vivo roles of DNA repair pathways. We cover a variety of critical biological processes including neurogenesis, hematopoiesis, germ cell development, tumorigenesis, and aging, with a specific emphasis on findings obtained from the use of zebrafish as a model system. Our comprehensive review highlights the importance of zebrafish in enhancing our understanding of the functions of DNA repair systems at the organismal level and paves the way for future investigations in this field. [ABSTRACT FROM AUTHOR]

Honey produced by A. mellifera contains minor components present in the nectar collected from plants. Various studies of honey components and all other bee products can be informative in assessing their quality. The aim of the present study was to determine the content and composition of fatty acids (FAs) in sea buckthorn oil (SBO), royal jelly (RJ) and bee pollen (BP) and the changes in FAs content in these products during storage. The diversity of FAs and the effect of storage time on FAs content was also evaluated for the prepared-for-preservation mixtures, which included the following samples: pollen mixed with honey at a ratio of 1:2 (w/w); sample BPH, a well; BPH + 1% (w/w) SBO; and BPH + 1% (w/w) SBO + 2% (w/w) RJ. Fresh bee-collected pollen and RJ were stored at −20 °C, whereas the conserved samples were stored at +4 °C in hermetically sealed jars. The data revealed that RJ demonstrated the highest diversity of fatty acids compared to BP and BP prepared for storage with honey along with SBO and RJ. Palmitic and stearic acids were found in the highest amounts out of the eight saturated fatty acids identified in the studied SBO and RJ. The amount of these fatty acids in RJ compared to SBO was 1.27 and 6.14 times higher, respectively. In total, twenty-two unsaturated fatty acids (USFA) were identified in RJ and fourteen were found in SBO. The SBO used in this study was found to be high in linoleic acid, resulting in an increased n-6 fatty acids ratio in the prepared samples. Essential fatty acids eicosapentaenoic (EPA) and docosahexaenoic (DHA) were found in RJ, as well as in BP and BP mixed with honey. These FAs were not identified in the samples prepared with SBO even in the sample supplemented with RJ. The highest decrease in docosadienoic fatty acid was found in the BPH sample compared to BP, while arachidonic acid mostly decreased in BPH + 1% SBO compared to the BPH + 1% (w/w) SBO + 2% (w/w) RJ samples stored at +4 °C. Bee-collected pollen had the greatest influence on the number of FAs in its mixture with honey. [ABSTRACT FROM AUTHOR]

It is known that a number of parts that operate in liquid media, such as the propellers of motorboats and pleasure river vessels, as well as the rotors of household pumps and the radiators and pumps in the cooling system of motor vehicles are made, as a rule, of aluminum-based alloy. Research during maintenance leads to the conclusion that, in certain operating conditions, due to the turbulent character of the flow, with pressure drops to below the vaporization level, it inevitably reaches the threshold of cavitation, which manifests itself through its effects, especially through erosion. To increase the lifetime, these alloys are currently subjected to techniques to improve the structure's resistance to the cyclic stresses of cavitational microjets. Among these techniques are volumetric heat treatments, which lead to changes in the microstructure and mechanical property values, with an effect on the behavior and resistance to cavitation erosion. This paper studies the influence of heat aging treatments on the cavitation erosion behavior of an aluminum alloy type 6082, in the cast state. The heat treatments applied were 140 °C/1 h, 12 h, 24 h and 180 °C/1 h, 12 h, 24 h. The MDEmax and MDERs parameters were determined and a correlation could be made between the values of the mechanical-resilient characteristics and the resistance to cavitation erosion in the case of aluminum alloy 6082. [ABSTRACT FROM AUTHOR]

As a group of antibiotics largely used in China's animal husbandry, fluoroquinolone (FQ) residues in honey may pose potential threats to human health. This study performed a five-year investigation on the occurrence of FQ residues in honey in 521 Apis mellifera and 160 Apis cerana honey samples collected from Zhejiang Province, China and compared FQ residue profiles in honey with a subgroup of various factors. Deterministic and probabilistic risk assessments of exposure to FQ residues in honey were further conducted. Overall, four FQs were detected in 6.9% (47/681) of analyzed samples; banned norfloxacin with the highest level (7890 μg·kg−1) and detection frequency (4.9%) was the primary safety risk factor associated with honeybees raised in China. FQ detection frequency and concentration of rape honey was highest among four of the largest and most stable honeys (rape, acacia, chaste, and linden) in China. Processed honey from commercial sale channels had a significantly higher detection frequency of FQ residues than raw honey from apiaries. Deterministic assessment showed that the noncarcinogenic hazard quotient (HQ) value of the dietary intake of FQs by the local population was between 4.75 × 10−6 and 1.18 × 10−3, less than 1.0, indicating that FQ residues in honey posed a low risk for consumers. The order of the HQ value was ciprofloxacin > norfloxacin > enrofloxacin > ofloxacin. Probabilistic assessment showed that at P95, the HQ of FQs for the age groups of children, adolescents, adults, and older adults over 65 years ranged from 2.39 × 10−5 to 0.217, less than 1, and the exposure risk for adults was higher than for children and adolescents. Sensitivity analysis showed that FQ concentrations were the major contributors to health risks. Although a low risk was found, a strict hive management is needed for beekeepers regarding troubles of food safety, international trade, and human bacterial resistance. [ABSTRACT FROM AUTHOR]

The water retention curve (WRC) of a geosynthetic clay liner (GCL) is influenced by the presence of exchangeable cations in the leachate during changes in water content in a landfill construction. This research aims to investigate the impact of salinity on the WRC of GCL. To measure the WRC of GCL under different sodium chloride (NaCl) concentrations on the drying path, a chilled-mirror dew-point device capable of controlling the GCL's volume was employed. Additionally, the dry state microstructure of the GCL was examined using electron microscopy. The test outcomes indicate that GCL hydrated with higher salinity has greater suction at the same water content during drying. This influence can be attributed to changes in salinity and the precipitation of NaCl crystals within the bentonite when water evaporates, which in turn affects the bentonite's microstructure and leads to increased matric suction. By introducing the Fredlund and Xing model and parameter relationship, it is possible to predict the WRC of GCL under salinity effects after measuring the WRC under different salinity conditions on the drying path. [ABSTRACT FROM AUTHOR]

In the present paper, different surface preparations are investigated with the aim of increasing the wear behaviour of an electrophoretic graphene coating on a copper plate. The study was divided into two steps: In the first step (pre-tests), to detect the most promising pretreatment technology, five different surface preparations were investigated (electropolishing, sandblasting, degreasing and pickling, laser cleaning and laser dots).In the second step, on the basis of the results of the first step, a 32 full factorial plan was developed and tested; three treatment types (pickled and degreased, laser-cleaned, and laser dots) and three different voltages (30, 45 and 60 V) were adopted. Analysis of variance (ANOVA) was used to evaluate their influence on wear resistance; in particular, the maximum depth and width of the wear tracks and the coating break distance were investigated. The results of this study show that, in optimal conditions, laser treatment (particularly laser dots) canlead to as high as a four-fold increase in wear resistance. [ABSTRACT FROM AUTHOR]

In the present study, Fe1.1(CrxMn1-x)1.9O4 nanoparticles (0 ≤ x ≤ 0.5) were successfully synthesized by a combustion method, and the influence of Cr substitution on the structural and magnetic properties of the obtained nanoparticles was studied by various methods. The structural analysis revealed that the sample with x = 0 has a tetragonal structure, while all Cr-doped samples crystallize into a cubic structure. Additionally, the results of TEM show that doping with chromium leads to an increase in particle size. The magnetic hysteresis loops demonstrate the behavior typical for soft magnetic materials with low coercivity and remanence magnetization. The magnetic measurements revealed that the saturation magnetization of the obtained nanoparticles demonstrates a decreasing trend with increasing Cr content. The influence of chromium doping on the observation change in saturation magnetization is discussed. Based on the results of temperature-dependent magnetization measurements, it was found that the temperature of a magnetic transition in synthesized nanoparticles depends on Cr content. [ABSTRACT FROM AUTHOR]

Quinoa (Chenopodium quinoa Willd.) is a dicotyledonous cereal that is rich in nutrients. This important crop has been shown to have significant tolerance to abiotic stresses such as salinization and drought. Understanding the underlying mechanism of stress response in quinoa would be a significant advantage for breeding crops with stress tolerance. Here, we treated the low-altitude quinoa cultivar CM499 with either NaCl (200 mM), Na2CO3/NaHCO3 (100 mM, pH 9.0) or PEG6000 (10%) to induce salinity, alkalinity and hypertonia, respectively, and analyzed the subsequent expression of genes and small RNAs via high-throughput sequencing. A list of known/novel genes were identified in quinoa, and the ones responding to different stresses were selected. The known/novel quinoa miRNAs were also identified, and the target genes of the stress response ones were predicted. Both the differently expressed genes and the targets of differently expressed miRNAs were found to be enriched for reactive oxygen species homeostasis, hormone signaling, cell wall synthesis, transcription factors and some other factors. Furthermore, we detected changes in reactive oxygen species accumulation, hormone (auxin and ethylene) responses and hemicellulose synthesis in quinoa seedlings treated with stresses, indicating their important roles in the response to saline, alkaline or hyperosmotic stresses in quinoa. Thus, our work provides useful information for understanding the mechanism of abiotic stress responses in quinoa, which would provide clues for improving breeding for quinoa and other crops. [ABSTRACT FROM AUTHOR]