Search

A CFD model was performed with commercial software through the adoption of the finite volume method and a SIMPLE algorithm. SiO2-P25 particles were added to water/ethylene glycol as a base fluid. The result is considered a new hybrid nanofluid (HN) for investigating heat transfer (HT). The volume concentrations were 0.5, 1.0, and 1.5%. The Reynolds number was in the range of 5000–17,000. The heat flux (HF) was 7955 W/m2, and the wall temperature was 340.15 K. The numerical experiments were performed strictly following the rules that one should follow in HT experiments. This is important because many studies related to nanofluid HT overlook these details. The empirical correlations that contain the friction factor perform better with higher Reynolds numbers than the correlations based only on Reynolds and Prandtl numbers. When temperature differences are moderate, researchers may consider using constant properties to lower computational costs, as they may give results that are similar to temperature-dependent ones. Compared with previous research, our simulation results are in agreement with the experiments in real time. [ABSTRACT FROM AUTHOR]

The progressive use of renewable energy sources to ensure a continuous and abundant energy supply is the significant target towards a sustainable and secure energy system. Previously, the countries that had relied on fossil fuel as a dominating energy source are now endorsing energy system transition towards renewable energy sources. In this study, a comparative assessment of the energy problems of South Asian countries is summarized. Nevertheless, there are many similarities and differences in the electricity supply system of these countries. Long-term planning for renewable energy development is suggested for a diverse population and dispersed geographical location considering all the significant challenges. However, appropriate schemes are imperative for integrating significant renewable energy sources. This study introduces a foresight plan of the electricity model according to the demand and supply balance for extensive technical analysis. The EnergyPLAN modeling tool was employed to work out a more ambitious VRE integration scenario than the official plans. The reference model was validated according to legitimate and authentic data, and then, the technically most feasible renewable energy-based alternate scenario was built. The additional grid integration cost of variable renewable energy was quantitatively investigated for comprehensive power system modeling for a real-time economic analysis. The results may be adapted and support developing more sustainable power generation serving 1787 million in South Asian countries. [ABSTRACT FROM AUTHOR]

In the current research, surface-modified SiO2 nanoparticles were used upon immersion in an applied base fluid (ethylene glycol:water = 1:1). The atomic layer deposition method (ALD) was introduced to obtain a thin layer of TiO2 to cover the surface of SiO2 particles. After the ALD modification, the TiO2 content was monitored by energy dispersive X-ray spectroscopy (EDS). Transmission electron microscopy (TEM) and FT-IR spectroscopy were applied for the particle characterization. The nanofluids contained 0.5, 1.0, and 1.5 volume% solid particles and zeta potential measurements were examined in terms of colloid stability. A rotation viscosimeter and thermal conductivity analyzer were used to study the nanofluids' rheological properties and thermal conductivity. These two parameters were investigated in the temperature range of 20 °C and 60 °C. Based on the results, the thin TiO2 coating significant impacted these parameters. [ABSTRACT FROM AUTHOR]

In this paper, we present a study on thermal conductivity and viscosity of nanofluids containing novel atomic layer deposition surface-modified carbon nanosphere (ALD-CNS) and carbon nanopowder (ALD-CNP) core-shell nanocomposites. The nanocomposites were produced by atomic layer deposition of amorphous TiO2. The nanostructures were characterised by scanning (SEM) and transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, thermogravimetry/differential thermal analysis (TG/DTA) and X-ray powder diffraction (XRD). High-concentration, stable nanofluids were prepared with 1.5, 1.0 and 0.5 vol% nanoparticle content. The thermal conductivity and viscosity of the nanofluids were measured, and their stability was evaluated with Zeta potential measurements. The ALD-CNS enhanced the thermal conductivity of the 1:5 ethanol:water mixture by 4.6% with a 1.5 vol% concentration, and the viscosity increased by 37.5%. The ALD-CNS increased the thermal conductivity of ethylene–glycol by 10.8, whereas the viscosity increased by 15.9%. The use of a surfactant was unnecessary due to the ALD-deposited TiO2 layer. [ABSTRACT FROM AUTHOR]

The solar chimney power plant (SCPP) is a straightforward and clean technique to generate electricity from solar radiation. However, this technology still faces major challenges, such as low efficiency, which has hindered its industrialization. This study experimentally develops a novel collector design to improve the solar chimney collector's efficiency. The new design includes metallic tubes as solar radiation absorbers hung from the canopy of the collector. The metallic tubes are open at the top and sealed with transparent sheets at the bottom to decrease the solar radiation reflected into the ambient air. Experimental and 3-D computational fluid dynamics (CFD) analyses are performed to validate the new design. The effects of hanging metallic tubes on temperature and velocity distribution are explored. The temperature increased by about 5 K at the chimney inlet, causing a roughly 8% rise in collector efficiency due to the fact that metallic tubes operate as an extended surface. The impact of various tube geometries on solar chimneys' efficiency is examined. The CFD findings reveal that the metallic tube geometry variation has considerably impacted the collector's efficiency. Thus, the collector efficiency is increased by changing tube diameter by around 33.7%, similar to changing tube length by 30%. [Display omitted] • A new solar chimney's collector design was experimentally developed and compared with CFD simulation. • Effects of hung metallic tubes on air temperature and velocity distribution were explored. • Effects of various metallic tube geometries on the collector's efficiency were studied and compared. • The collector efficiency increased from 25% in conventional solar chimneys to 33.90% in the improved ones. [ABSTRACT FROM AUTHOR]

Halloysite nanotube (HNT) which is cheap, natural, and easily accessible 1D clay, can be used in many applications, particularly heat transfer enhancement. The aim of this research is to study experimentally the pool boiling heat transfer (PBHT) performance of novel halloysite nanofluids at atmospheric pressure condition from typical horizontal heater. The nanofluids are prepared from halloysite nanotubes (HNTs) nanomaterials-based deionized water (DI water) with the presence of sodium hydroxide (NaOH) solution to control pH = 12 to obtain stable nanofluid. The nanofluids were prepared with dilute volume concentrations of 0.01–0.5 vol%. The performance of PBHT is studied via pool boiling curve and pool boiling heat transfer coefficient (PBHTC) from the typical heater which is the copper horizontal tube with a thickness of 1 mm and a diameter of 22 mm. The temperatures of the heated tube surface are measured to obtain the PBHTC. The results show an improvement of PBHTC for halloysite nanofluids compared to the base fluid. At 0.05 vol% concentration, HNT nanofluid has the best enhancement of 5.8% at moderate heat flux (HF). This indicates that HNT is a potential material in heat transfer applications. [ABSTRACT FROM AUTHOR]