Search

Ultrathin and two-dimensional (2D) metals can support strong plasmons, with concomitant tight field confinement and large field enhancement. Accordingly, 2D-metal nanostructures exhibiting plasmonic resonances are highly sensitive to the environment and intrinsically suitable for optical sensing. Here, based on a proof-of-concept numerical study, nano-engineered ultrathin 2D-metal films that support infrared plasmons are demonstrated to enable highly responsive refractive index (RI) sensing. For 3 nm-Au nanoribbons exhibiting plasmonic resonances at wavelengths around 1600 nm, a RI sensitivity of SRI > 650 nm per refractive index unit (RIU) is observed for a 100 nm-thick analyte layer. A parametric study of the 2D-Au system indicates the strong dependence of the RI sensitivity on the 2D-metal thickness. Furthermore, for an analyte layer as thin as 1 nm, a RI sensitivity up to 110 (90 nm/RIU) is observed in atomically thin 2D-In (2D-Ga) nanoribbons exhibiting highly localized plasmonic resonances at mid-infrared wavelengths. Our results not only reveal the extraordinary sensing characteristics of 2D-metal systems but also provide insight into the development of 2D-metal-based plasmonic devices for enhanced IR detection. [ABSTRACT FROM AUTHOR]

Background Coronary heart disease (CHD) is a cardiovascular disease with high mortality. At present, percutaneous coronary intervention (PCI) is considered as the main effective treatment for CHD due to less trauma, shorter course of treatment, and better curative effect. However, PCI alone is not a permanent cure, so cardiac rehabilitation (CR) is needed for a supplement. Nowadays, the evaluation of the nursing-sensitive quality of CR after PCI focuses on the outcomes of patients, lacks a complete evaluation indicator system, and is prone to problems such as nursing management imbalance. Objective A scientific, sensitive, comprehensive and practical nursing-sensitive quality indicator system based on the structure-process-outcome model was constructed to provide a reference for evaluating nursing sensitive quality of CR after PCI. Methods Firstly, through literature analysis and semi-structured interview, the indicator system was collected, screened and determined. Then, the framework of the indicator system was established, and the draft of nursing-sensitive quality indicator system of CR after PCI was formed. Subsequently, the nursing-sensitive quality indicator system of CR after PCI was initially established using Delphi method. Finally, the specific weight was determined by analytic hierarchy process (AHP), and the nursing-sensitive quality indicator system of CR after PCI was established and perfected. Results Two rounds of expert consultations were separately given 15 questionnaires, and all these questionnaires were returned, with a questionnaire response rate of 100%. Such result indicated that experts were highly motivated. Besides, the authoritative coefficients for two rounds of expert consultations were 0.865 and 0.888, and the coordination coefficients were 0.491 and 0.522, respectively. Hence, the experts’ authority and coordination were high and the results were reliable. After the second round of expert consultation, the nursing-sensitive quality indicator system of CR after PCI was established, eventually. This system consisted of 3 first-level indicators (structural indicator, process indicator and outcome indicator), 11 s-level indicators and 29 third-level indicators. Conclusion A relatively complete and reliable nursing-sensitive quality indicator system of CR after PCI has been established in this study. Such system is scientific and reliable and can provide a reference for the evaluation of clinical teaching quality of CR after PCI. [ABSTRACT FROM AUTHOR]

The microstructures and mechanical properties of laser penetration welded joints of overlap steel-on-aluminum were investigated. The structure of the intermetallic compound layer without interlayer consists of FeAl and FeAl3 phases. After the Ni-foil was added, the thickness of the intermetallic compound layer and the content of the brittle and hard Al-Fe phase decreased significantly, and some new phases of Al0.9Ni1.1 and FeNi were formed. It was found that the Ni interlayer enhanced the tensile property of the joint by about 40% and decreased the microhardness of the intermetallic compounds, which is attributed to the improvement of the toughness of the welded joint made by the Ni interlayer. It is an effective way to improve the mechanical properties of the laser welding joint by adding a nickel interlayer to improve the metallurgical reaction. [ABSTRACT FROM AUTHOR]

Phononic crystals are a kind of artificial acoustic metamaterial whose mass density and elastic modulus are periodically arranged. The precise and efficient design of phononic crystals with specific bandgap characteristics has attracted increasing attention in past decades. In this paper, an improved adaptive genetic algorithm is proposed for the reverse customization of two-dimensional phononic crystals designed to maximize the relative bandwidth at low frequencies. The energy band dispersion relation and transmission loss of the optimal structure are calculated by the finite-element method, and the effective wave-attenuation effect in the bandgap range is verified. This provides a solution for the custom-made design of acoustic metamaterials with excellent low-frequency bandgap sound insulation or other engineering applications. [ABSTRACT FROM AUTHOR]

The flammability and gas barrier properties are essential for package material. Herein, a highly-oriented self-assembly nanocoating composed of polyvinyl alcohol (PVA) and montmorillonite (MMT) was prepared for endowing polyethylene terephthalate (PET) films with excellent flame retardancy and gas barrier properties. The specific regular nanosheet structure of the PVA/MMT composite nanocoating was confirmed by Fourier transform infrared (FTIR) and X-ray diffraction (XRD). Thermogravimetric analysis (TGA) and the vertical burning test (VBT) suggested that the thermal stability and flame-retardancy of the coated PET films were considerably improved with more pick-up of the resulting nanocoating. When reaching 650 °C, there was still 22.6% char residual left for coated PET film, while only 6% char residual left for pristine PET film. During the vertical burning test, the flame did not spread through the whole PET film with the protection of PVA/MMT nanocoating, and no afterflame was observed. Scanning electron microscopy (SEM) is consistent with vertical burning test, proving that the thermal stability and flame retardancy of coated PET films were considerably enhanced with the increment of PVA/MMT. Thanks to the multi-layer structure, PVA/MMT nanocoating could effectively improve the gas barrier properties of PET films, and the oxygen vapor transmittance rate and water vapor transmittance rate of PET films were more than four hundred times lower and 30% lower than those of neat PET film. Our work demonstrates that bi-functional flame retardant and gas barrier materials could be gained via constructing inorganic/organic highly-oriented self-assembly nanocoating, which is promising in the area of packaging. [ABSTRACT FROM AUTHOR]

It is very appealing to develop cheap, highly sensitive and efficient metal ion fluorescence sensors as traditional instrument methods are inherently costly and time‐consuming. Carbon dots (CDs) are widely used for sensing metal ions, attributing to their merits of good biocompatibility, low toxicity, easy surface modification and excellent photostability. This article reviewed the research progress of CDs as metal ion sensors in recent years, and studied their modification methods and detection performances. Finally, the challenges and opportunities of CDs as metal ion sensors were also analyzed. This article is expected to provide inspiration and help for researchers focusing on CDs as metal ion sensors. [ABSTRACT FROM AUTHOR]

Chiral nanostructures have immense potential for complete polarization control of light. Given the intrinsic 3D structure of circularly polarized light, nanoarchitectures with structural chirality in 3D space are usually required to achieve "full" chiroptical response. On the other hand, due to the lack of available active materials at optical wavelengths, examples of chiral photonic devices that can be tuned in an active manner remain rare. Here, based on the large Kerr nonlinearities of silicon, the nonlinear chiroptical response from a planar Si metasurface supporting high quality (Q)‐factor guided mode resonances (GMRs) at near‐infrared wavelengths, are numerically demonstrated. In the linear regime, the optical anisotropy of the C2‐symmetric structure associated with the observed GMRs leads to a pair of chiral resonance modes, enabling pronounced cross‐polarization transmission circular dichroism and a strong handedness‐dependent field enhancement effect. Owing to the nonlinear Kerr effect, such Si metasurfaces are seen to exhibit prominent chiral‐selective optical nonlinearity. Importantly, a pronounced co‐polarization transmission circular dichroism is observed, suggesting that the circularly polarized waves in the nonlinear regime possess asymmetric Jones matrices. Dielectric chiral metasurfaces with Kerr nonlinearities can be utilized to facilitate polarization‐state modulators with simple planar structures. [ABSTRACT FROM AUTHOR]

Notched beam specimens were loaded by the three-point bending test device, and the effects of different volume contents and combinations of steel fibers on the tensile properties of hybrid steel fiber–reinforced self-compacting concrete (HSFRSCC) were studied. The failure law and strain field distribution of the specimens were studied by digital image correlation (DIC) technology. Moreover, the curves between the load and crack mouth opening displacement (CMOD) of 18 groups of hybrid steel fiber–reinforced concrete specimens were obtained, and the stress–strain curves of 18 groups of specimens were derived from the load–CMOD curves. The results show that both single and hybrid steel fibers can improve the crack deformation resistance and tensile properties of concrete, but hybrid steel fibers have a more significant improvement effect. Only when the content of steel fiber is more than 0.6% can it have a more obvious postpeak descending section, and hybrid steel fiber has higher postpeak deformation capacity and flexural toughness. The fundamental reason why concrete with hybrid steel fibers has better tensile properties is that micro and macro steel fibers cooperate with each other to resist cracks, improving the toughness of concrete after cracking. Finally, the mechanism of different size and volume content of steel fiber was analyzed from the micro level, which can be used as a reference for the engineering design of HSFRSCC in the future. [ABSTRACT FROM AUTHOR]

Hydrogen solubility was determined in olivine and orthopyroxene under water‐saturated conditions at P = 3–5 GPa and T = 1373–1573 K. For olivine, polycrystalline samples were prepared from San Carlos olivine, and for orthopyroxene synthetic samples were prepared from oxide mixture containing 1.5–5 wt% of Al2O3. Olivine and orthopyroxene were placed next to each other and annealed under various pressure and temperature conditions for 3–5 hr. Hydrogen content was measured across each sample by FTIR spectroscopy. Under the water‐saturated conditions, the hydrogen solubility in olivine increases with pressure and temperature similar to previous results. Hydrogen solubility in Al2O3‐bearing orthopyroxene also increases with temperature and pressure for a fixed Al2O3 content. Based on these observations we calculated the partition coefficients of hydrogen between orthopyroxene and olivine assuming the fugacity dependence of hydrogen solubility in olivine and Al2O3‐bearing orthopyroxene reported by previous studies. We find that the partition coefficient depends weakly on temperature but strongly on pressure and water fugacity. Our results are extended to an open system where Al2O3 content in orthopyroxene changes with pressure and temperature. At relatively low pressures and low water fugacity (in the lithosphere (shallower than ∼50 km)), the partition coefficient is high and a majority of hydrogen is present in orthopyroxene. Consequently, the influence of water on the bulk physical properties is small. In contrast, at higher pressures and higher water fugacity (in the asthenosphere), the partition coefficient is smaller and a substantial amount of hydrogen is present in olivine. Consequently, hydrogen has a strong effect on the bulk properties of the asthenosphere reducing viscosity and increasing electrical conductivity. Plain Language Summary: Water has strong influence on a number of physical and chemical properties of minerals and rocks, and therefore distribution of hydrogen in the deep Earth has been studied extensively. For the upper mantle, some rock samples are available and we can directly determine the hydrogen content in these minerals. However, samples collected from various localities have experienced a broad range of thermodynamic conditions since they were at chemical equilibrium when partial melting (including cooling) occurred and water loss during transportation to the surface. Therefore, a correction needs to be applied to the influence of thermodynamic history if one wants to learn hydrogen distribution in Earth from these rock samples. So, the purpose of this study is to determine the hydrogen partition coefficient between olivine and orthopyroxene at a variety of thermodynamic conditions including pressure, temperature and water fugacity. Key Points: Hydrogen solubility was determined in olivine and orthopyroxene under water‐saturated conditions at P = 3–5 GPa and T = 1373–1573 KWe found that hydrogen content in Al2O3‐bearing orthopyroxene increases with temperature and pressure for a fixed Al2O3 contentThe hydrogen partition coefficient between olivine and orthopyroxene depends weakly on temperature but strongly on pressure and water fugacity [ABSTRACT FROM AUTHOR]

Carbon dots (CDs) can be widely used in the field of sensing because of its good water solubility, low toxicity, high fluorescence stability and excellent biocompatibility. It has become a popular trend to prepare high-value, inexpensive, renewable and environmentally friendly CDs sensors from biomass resources. This article reviewed the research progress of biomass-derived CDs as chemical, physical and biological sensors in recent years and studied their preparation processes and sensing abilities. Furthermore, the prospects and challenges of biomass-CDs sensors were discussed. This article is expected to provide inspirations for the design, preparation and application of biomass-CDs sensors in the future. [ABSTRACT FROM AUTHOR]

Handwritten Text Recognition has achieved an impressive performance in public benchmarks. However, due to the high inter- and intra-class variability between handwriting styles, such recognizers need to be trained using huge volumes of manually labeled training data. To alleviate this labor-consuming problem, synthetic data produced with TrueType fonts has been often used in the training loop to gain volume and augment the handwriting style variability. However, there is a significant style bias between synthetic and real data which hinders the improvement of recognition performance. To deal with such limitations, we propose a generative method for handwritten text-line images, which is conditioned on both visual appearance and textual content. Our method is able to produce long text-line samples with diverse handwriting styles. Once properly trained, our method can also be adapted to new target data by only accessing unlabeled text-line images to mimic handwritten styles and produce images with any textual content. Extensive experiments have been done on making use of the generated samples to boost Handwritten Text Recognition performance. Both qualitative and quantitative results demonstrate that the proposed approach outperforms the current state of the art. [ABSTRACT FROM AUTHOR]

Porcine reproductive and respiratory syndrome virus (PRRSV) infection inhibits swine leukocyte antigen class I (SLA-I) expression in pigs, resulting in inefficient antigen presentation and subsequent low levels of cellular PRRSV-specific immunity as well as persistent viremia. We previously observed that the non-structural protein 4 (nsp4) of PRRSV contributed to inhibition of the β2-microglobulin (β2M) and SLA-I expression in cells. Here, we constructed a series of nsp4 mutants with different combination of amino acid mutations to attenuate the inhibitory effect of nsp4 on β2M and SLA-I expression. Almost all nsp4 mutants exogenously expressed in cells showed an attenuated effect on inhibition of β2M and SLA-I expression, but the recombinant PRRSV harboring these nsp4 mutants failed to be rescued with exception of the rPRRSV-nsp4-mut10 harboring three amino acid mutations. However, infection of rPRRSV-nsp4-mut10 not only enhanced β2M and SLA-I expression in both cells and pigs but also promoted the DCs to active the CD3+CD8+T lymphocytes more efficiently, as compared with its parental PRRSV (rPRRVS-nsp4-wt). These data suggested that the inhibition of nsp4-mediated β2M downregulation improved β2M/SLA-I expression in pigs. • The Nsp4 gene of PRRSV on virus level inhibit the expression of β2M/SLA-I gene in pigs in this research filed. • The three amino acid sites of Nsp4 gene we have screened play a key role in inhibition of the expression of β2M/SLA-I gene in pigs. • The rPRRSV-nsp4-mut10 can induce more expression of β2M/SLA-I which accelerates the clearance of PRRSV in pigs. [ABSTRACT FROM AUTHOR]

porcine reproductive and respiratory syndrome (PRRS), caused by porcine reproductive and respiratory syndrome virus (PRRSV) infection, is an important swine infectious disease that causes substantial losses worldwide each year. PRRSV is a positive-sense single-stranded RNA virus that is highly susceptible to mutation and recombination, making vaccine and drug research for the disease extremely difficult. In this study, the binding of PRRSV nsp2 to HSP71 protein was detected by using the IP/MS technique. And the inhibitory effect of HSP71 on nsp2 antagonistic activity was validated by measuring NF-kB luciferase reporter. According to stress from inhibitory effects, the amino acid variation profile of PRRSV nsp2 under HSP71 stress was further analyzed using second-generation sequencing. Surprisingly, the results indicated that HSP71 pressure limits the random mutations of PRRSV nsp2 and maintains the dominant PRRSV strain within the population. Mutant strain showed weaker antagonistic activity and replication capability in cell. These results imply the binding of HSP71 with PRRSV nsp2 may lead to maintain the stability of highly virulent strains of PRRSV. • Hsp71 binds and inhibits PRRSV nsp2. • hsp71 binding contributes to the stabilization of PRRSV nsp2. • PRRSV nsp2 is prone to random mutations in normal cells. [ABSTRACT FROM AUTHOR]

The resonant nature and geometric scalability make metamaterials an ideal platform for an enhanced light–matter interaction over a broad frequency range. The mid-infrared (IR) spectral range is of great importance for vibrational spectroscopy of molecules, while IR metamaterials created from lithography-based planar nanostructures have been used to demonstrate enhanced molecular detection. Compared with visible and near-infrared, the relative long wavelengths of IR light make it possible to achieve three-dimensional (3D) IR metamaterials via the state-of-the-art 3D fabrication techniques. Here, we design and fabricate a 3D printed plasmonic metamaterial absorber (MMA), and by performing Fourier-transform IR spectroscopy, we demonstrate that a series of molecular fingerprint vibrations of glycine can be significantly enhanced by the high absorption mode supported by the 3D meta-atoms of the MMA. The observed enhanced IR detection can also be partially attributed to the improved accessibility offered by the 3D architecture of the MMA. In particular, due to capillary forces during the drying process, the microscale 3D printed features lead to selective analyte deposition in high-field regions, which provides another degree of freedom in the design of the 3D printed structures for surface-enhanced IR detection. Our study shows the flexibility of metastructures based on advanced 3D printing technology in tailoring the interaction between IR light and materials on a subwavelength scale. [ABSTRACT FROM AUTHOR]

Purpose: Abnormal CD38 expression in some hematologic malignancies, including lymphoma, has made it a biomarker for targeted therapies. Daratumumab (Dara) is the first FDA-approved CD38-specific monoclonal antibody, enabling successfully immunoPET imaging over the past years. Radiolabeled Dara however has a long blood circulation and delayed tumor uptake which can limit its applications. The focus of this study is to develop 64Cu-labeled Dara-F(ab′)2 for the visualization of CD38 in lymphoma models. Methods: F(ab′)2 fragment was prepared from Dara using an IdeS enzyme and purified with Protein A beads. Western blotting, flow cytometry, and surface plasmon resonance (SPR) were performed for in vitro assay. Probes were labeled with 64Cu after the chelation of 1,4,7-triazacyclononane-1,4,7-triacetic acid (NOTA). Small animal PET imaging and quantitative analysis were performed after injection of 64Cu-labeled Dara-F(ab′)2, IgG-F(ab′)2, and Dara for evaluation in lymphoma models. Results: Flow cytometry and SPR assay proved the specific binding ability of Dara-F(ab′)2 and NOTA-Dara-F(ab′)2 in vitro. Radiolabeling yield of [64Cu]Cu-NOTA-Dara-F(ab′)2 was over 90% and with a specific activity of 4.0 ± 0.6 × 103 MBq/μmol (n = 5). PET imaging showed [64Cu]Cu-NOTA-Dara-F(ab′)2 had a rapid and high tumor uptake as early as 2 h (6.9 ± 1.2%ID/g) and peaked (9.5 ± 0.7%ID/g) at 12 h, whereas [64Cu]Cu-NOTA-Dara reached its tumor uptake peaked at 48 h (8.3 ± 1.4%ID/g, n = 4). In comparison, IgG-F(ab′)2 and HBL-1 control groups found no noticeable tumor uptake. [64Cu]Cu-NOTA-Dara-F(ab′)2 had significantly lower uptake in blood pool, bone, and muscle than [64Cu]Cu-NOTA-Dara and its tumor-to-blood and tumor-to-muscle ratios were significantly higher than controls. Conclusions: [64Cu]Cu-NOTA-Dara-F(ab′)2 showed a rapid and high tumor uptake in CD38-positive lymphoma models with favorable imaging contrast, showing its promise as a potential PET imaging agent for future clinical applications. [ABSTRACT FROM AUTHOR]

The Pancharatnamâ€"Berry phase induced by the winding topology of polarization around a vortex singularity at bound states in the continuum (BIC) provides a unique approach to optical vortex (OV) generation. The BIC-based OV generators have the potential to outperform their counterparts that rely on spatial variations in terms of design feasibility, fabrication complexity, and robustness. However, given the fact that this class of OV generators originates from the topological property of the photonic bands, their responses are generally fixed and cannot be dynamically altered, which limits their applications to photonic systems. Here, we numerically demonstrate that a silicon photonic crystal slab can be used to realize optically switchable OV generation by simultaneously exploiting the vortex topology in momentum space in conjunction with silicon’s nonlinear dynamics. Picosecond switching of OV beams at near-infrared wavelengths are observed. The demonstrated nontrivial topological nature of the active generators can significantly expand the application of BIC toward ultrafast vortex beam generation, high-capacity optical communication, and mode-division multiplexing. [ABSTRACT FROM AUTHOR]

• Aspergillus and G- bacteria are the predominant strains in FN children. • mNGS is far superior to TPD in detecting fungal infections. • mNGS is conducive to targeted therapy and improved prognosis of FN children. To investigate the application value of metagenomic next-generation sequencing (mNGS) in children with hematological diseases presenting with Febrile Neutropenia (FN). We retrospectively analyzed the clinical data of 49 hematological children with FN, and compared the results of mNGS with those of traditional pathogen detection (TPD) and the prognoses of mNGS positive group and negative group. A total of 77 pathogenic strains were identified, of which 70 strains were detected by mNGS, 19 strains by TPD, and Aspergillus and G- bacterias were the predominant strains in FN children who developed bloodstream infections. 42 cases were in the mNGS-positive group, of which 17 were simple infections, 25 were mixed infections, and 7 were in the negative group; the TPD-positive group contained 19 cases, all of which were simple infections. The detection rate of total and mixed pathogens was higher than that of TPD, and the difference was statistically significant (P<0.05). The mNGS positive group was detected earlier than the negative group, and with lower mortality and drug-related adverse events (DRAE), and the difference was statistically significant (P<0.05). For FN children with hematological diseases, early mNGS can effectively improve the efficacy of pathogen detection, and precise treatment after clarifying the pathogens can reduce mortality and avoid antibiotic abuse. [ABSTRACT FROM AUTHOR]

Although the development of energy and mineral resources strongly supports China's rapid industrialization and urbanization, it has led to a series of ecological and environmental problems. Strengthening the spatial regulation considering the ecological and environmental protection on energy and mineral resource development areas is an important aspect of realizing China's sustainable development. In this study, we mapped, categorized, and analyzed the ecological cumulative effects of the Chinese 134 prefectural mining units based on the pressure-state-response model, which is demonstrated as impact of mining activities on ecological environment, ecological environmental fragility, and ecological function. This investigation developed a stress zoning typology of the mining units based on scores of three dimensions of the ecological cumulative effects and classified 134 prefectural mining units into eight types of stress zones. A series of regulation and policy suggestions have been proposed to different types of zones from three aspects: space control, intensity control, and development mode control. The application of this evaluation and spatial zoning system will contribute to the refined spatial management of China's mining areas. [ABSTRACT FROM AUTHOR]

[Display omitted] • A zwitterionic hydrogel was introduced for moisture-energy generation. • The polyelectrolyte changes were resisted through the salt-in effect. • The adsorption capacity of the hydrogel reached 3.0 g g−1 at 90% RH and 25 °C. • The device exhibiting an I sc of up to 945 μA cm−1 and a V oc of 0.802 V. Hygroscopic salt composite hydrogels (HSCHs) offer a promising solution for combating global water scarcity by harvesting atmospheric water. Importantly, this is aided by an interior water gradient that facilitates ion transport, which opens up opportunities for power generation. The current and potential outputs are restricted by inadequate water collection and excessive cross-link density. Herein, a novel zwitterionic nanocomposite conductive hydrogel (ZNCH) is introduced to resist polyelectrolyte changes by leveraging the salt-in effect of cationic and anionic functional groups. The poly-[2-(methacryloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide-based ZNCH endows the HSCH with an enhanced swelling property together with an improved water storage capacity. The adsorption capacity of water reaches 3.0 g g−1 after 10 h of operation at 25 °C and 90% RH. More importantly, ZNCH replaces H bonds with Li bonds under the Hofmeister effect, resulting in the generation of a substantial number of free H+ ions. These endow the ZNCH with highly efficient power generation performance, associating with a short-circuit current of up to 945 μA, a current density of 945 μA cm−1, and an open-circuit voltage of 0.802 V. This work motivates the improvement of materials and devices that convert energy from atmospheric water. [ABSTRACT FROM AUTHOR]

Sb 2 Te thin film exhibits remarkable crystallization speed, which allows rapid data conversion in phase change memory (PCM). Thermal stability is a key challenge to enable reliable data retention. Meanwhile, it is necessary to study the transition energy in the process of crystallization when the thermal stability of the amorphous state is improved. Herein, we demonstrated an alloying strategy to optimize thermal stability and transition energy. Zn was screened to be a promising alloying element. Nano-composite Zn 0.75 Sb 2 Te thin film was designed, which exhibited excellent thermal stability and optimized transition energy. The data retention temperature for 10 years (T 10-yr) increased by ∼ 218 %, and the transition energy consumption decreased by ∼ 27 % compared with Sb 2 Te thin film. The enhancement of these properties originated from Zn-modified local chemical bonding. Zn induced the formation of tetrahedron with strong bonds (Zn–Te and Zn–Sb bonds) and dragged the atomic diffusion in amorphous phase to improve thermal stability. The structural disorder and complexity of the first and second nearest neighbors of atoms were stimulated by Zn alloying, which inhibited the carrier transports, increased the amorphous resistance, and reduced the transition energy in the process of crystallization. [Display omitted] • An alloying strategy is proposed to improve the thermal stability. • Transition energy could also be reduced by the alloying strategy. • Zn induces the formation of tetrahedrons in amorphous Sb 2 Te film. • Nano-composite Zn–Sb 2 Te film is prepared. • Microstructure and phase change mechanism of Sb 2 Te film depend on the Zn content. [ABSTRACT FROM AUTHOR]

Rapid and high‐resolution histological imaging with minimal tissue preparation has long been a challenging and yet captivating medical pursuit. Here, the authors propose a promising and transformative histological imaging method, termed computational high‐throughput autofluorescence microscopy by pattern illumination (CHAMP). With the assistance of computational microscopy, CHAMP enables high‐throughput and label‐free imaging of thick and unprocessed tissues with large surface irregularity at an acquisition speed of 10 mm2/10 s with 1.1‐µm lateral resolution. Moreover, the CHAMP image can be transformed into a virtually stained histological image (Deep‐CHAMP) through unsupervised learning within 15 s, where significant cellular features are quantitatively extracted with high accuracy. The versatility of CHAMP is experimentally demonstrated using mouse brain/kidney and human lung tissues prepared with various clinical protocols, which enables a rapid and accurate intraoperative/postoperative pathological examination without tissue processing or staining, demonstrating its great potential as an assistive imaging platform for surgeons and pathologists to provide optimal adjuvant treatment. [ABSTRACT FROM AUTHOR]

Stemming from bound states in the continuum (BICs), momentum‐space polarization vortices observed in photonic structures provide an attractive approach to generating optical vortex (OV) beams. On the other hand, dominated by the selection rules, the harmonic generation from nanostructures exhibits a nonlinear geometric phase that depends on both the harmonic orders and the handedness of circularly polarized harmonic signals. Here, the third‐ and fifth‐harmonic optical vortex generation from an amorphous silicon photonic crystal slab, supporting the guided resonance associated with BICs at near infrared wavelengths, is numerically demonstrated. The results show that, determined by the nonlinearity phase, the topological charge (lnω) associated with the nth‐harmonic OV beams follows σ(n∓1)q, where q is the polarization charge of the BIC and the ∓ sign represents the opposite or same polarization of the nth‐harmonic signal relative to the circular polarization state (σ) of the fundamental waves. Exploiting harmonic multiplexing, this approach can significantly improve the channel capacity of OV generators based on topologically protected optical BICs. [ABSTRACT FROM AUTHOR]

Benefiting from the planar π-conjugated (HxC3N3O3)x−3 (x = 0–3) groups, cyanurate crystals have recently become a research hotspot in birefringent materials. Herein, by combining the (HxC3N3O3)x−3 (x = 0–3) group with the (CN3H6)+ cationic group, two metal-free cyanurates, GU(H2C3N3O3) (I) and GU3(H2C3N3O3)3(H3C3N3O3) (II), were obtained by the hydrothermal method. These compounds have wide band gaps (∼5 eV) and a large birefringence (∼0.40@400 nm), demonstrating their potential to be ultraviolet birefringent crystals. Moreover, first-principles calculations indicate that their large birefringence values originated from the synergistic effect of the (CN3H6)+ cations and (HxC3N3O3)x−3 (x = 0–3) groups. These findings provide a new design strategy for exploring low-cost UV birefringent crystals with a large birefringence. [ABSTRACT FROM AUTHOR]

Van der Waals (vdW) deep‐UV (DUV) nonlinear optical (NLO) crystal is an important material system recently developed. Herein, we review its concept and original intention, and then summarized the discovery process of related materials, including the role of A‐site cations and the resulting two‐/one‐dimensional vdW DUV NLO systems. Finally, we evaluate the practical DUV NLO performance and prospected the opportunities and challenges. [ABSTRACT FROM AUTHOR]

• Risk compensation effect of helmet use is studied based on selected bicyclists. • Targeted maximum likelihood estimator and ensemble learning are applied in this study. • Our results suggest the existence of risk compensation effect due to helmet use. Introduction: Safety is a critical factor in promoting sustainable urban non-motorized travel modes like bicycles. Helmets have shown to be effective in reducing injury severity in bicycle crashes, however, their effects on bicyclists' behaviors still requires deeper understanding, especially amid the emerging trend of using shared bicycles. Risk compensation effects suggest that bicyclists may offset perceived gains in safety from wearing a helmet by increasing risk-taking behaviors. A better understanding of these compensation effects can be useful in assessing various bicycle safety related programs. Method: Using a sample of 131 bicyclists from the San Francisco Bay area, this research studies how bicyclists respond with respect to risk-taking behaviors under various urban-street conditions, as a function of helmet use. Study participants were each shown 12 videos, shot in Berkeley, California, from the perspective of a bicyclist riding behind another bicyclist. A fractional factorial experiment design was used to systematically vary contextual attributes (e.g., speed, bike lane facilities, on-street parking, passing vehicles) across the videos. After each video, participants were asked to indicate if they would overtake the bicyclist in the video. With the help of data adaptive estimation techniques, targeted maximum likelihood estimation (TMLE) was applied to estimate the average risk difference between helmeted users and non-users, controlling for self-selection effects. Individual-based nonparametric bootstrap was performed to assess the uncertainty associated with the estimator. Results: Our findings suggest, on average, individuals more likely to wear a helmet are 15.6% more likely to undertake a risky overtaking maneuver. Practical Applications: This study doesn't try to oppose mandatory helmet laws, but rather serves as a cautionary warning that road safety programs may need to consider strategies in which unintended impact of bicycle helmet use can be mitigated. Moreover, our findings also provide additional evaluation component when it comes to the cost-benefit assessment of helmet-related laws. [ABSTRACT FROM AUTHOR]

Shear horizontal (SH) waves are commonly generated by periodic permanent magnet (PPM) electromagnetic acoustic transducers (EMATs) in metallic media. Conventional PPM EMATs generate ultrasonic waves, which simultaneously propagate both forward and backward. This can be an undesirable characteristic, since the backward wave can be eventually reflected, reaching the receiver transducer where it can mix with the signal of interest. This limitation can be overcome using two side-shifted PPM arrays and racetracks coils to generate SH waves in a single direction. That design relies on the EMAT wavefront diffraction to produce constructive and destructive interference, but produces unwanted backward traveling sidelobes. Here, we present a different design, which uses a conventional PPM array and a dual linear-coil array. The concept was numerically simulated, the main design parameters were assessed and the unidirectional EMAT was experimentally evaluated on an aluminum plate, generating the SH0-guided wave mode nominally in a single direction. The amplitude ratio of the generated waves at the enhanced to the weakened side is above 20 dB. Since the wavefronts from the two sources are perfectly aligned, no obvious backward sidelobes are present in the acoustic field, which can significantly reduce the probability of false alarm of an EMAT detection system. [ABSTRACT FROM AUTHOR]

Investigating green and effective means for ammonia synthesis is an important but challenging task. Electrochemical ammonia synthesis (EAS) from an indirect route (N2 → NOx → NH3) provides a feasible alternative strategy. The key step in this route is the reduction of NOx to NH3 instead of N2, which requires the investigation of efficient catalysts with high selectivity of NH3. Herein, we initially demonstrate a highly efficient electrochemical reduction of NO2− to NH3 with nickel phosphide (Ni2P) as the catalyst. The system exhibits low onset potential (0.2 V vs. RHE) and high faradaic efficiency (>90%) for EAS. Experimental results and theoretical calculations reveal that the in situ generated hydrogen atoms on the surface of Ni2P greatly promote the reduction of NO2− to NH3. [ABSTRACT FROM AUTHOR]

Van‐der‐Waals (vdW) deep‐ultraviolet (DUV) nonlinear‐optical (NLO) materials hold great potential to extend DUV NLO applications to two dimensions, but they are rare in nature. In this study, we propose a design principle to realize vdW DUV NLO materials via structural evolution from the non‐vdW (BO3)‐(BeO3F) layers in KBe2BO3F2 (KBBF) to the vdW (BO3)‐(BeO4H) layers in berborite Be2BO5H3 (BBH) and the vdW (BO4)‐(BeO4) layers in beryllium metaborate BeB2O4 (BEBO). Based on first‐principles calculations, the fundamental NLO properties of BBH and BEBO demonstrate that a balanced DUV NLO performance can be achieved in these two systems. Importantly, BBH, a layered material existing in nature, can achieve an available DUV phase‐matched output with strong second harmonic generation (SHG) for 177.3/193.7 nm DUV lasers, which is almost identical to that of KBBF. Remarkably, BEBO shows an excellent DUV SHG capacity and an even shorter phase‐matching wavelength than KBBF. Therefore, the newly discovered vdW BBH and BEBO, once verified by experiments, could provide an ideal platform to study DUV NLO effects in three dimensions and two dimensions. [ABSTRACT FROM AUTHOR]

Van‐der‐Waals (vdW) deep‐ultraviolet (DUV) nonlinear‐optical (NLO) materials hold great potential to extend DUV NLO applications to two dimensions, but they are rare in nature. In this study, we propose a design principle to realize vdW DUV NLO materials via structural evolution from the non‐vdW (BO3)‐(BeO3F) layers in KBe2BO3F2 (KBBF) to the vdW (BO3)‐(BeO4H) layers in berborite Be2BO5H3 (BBH) and the vdW (BO4)‐(BeO4) layers in beryllium metaborate BeB2O4 (BEBO). Based on first‐principles calculations, the fundamental NLO properties of BBH and BEBO demonstrate that a balanced DUV NLO performance can be achieved in these two systems. Importantly, BBH, a layered material existing in nature, can achieve an available DUV phase‐matched output with strong second harmonic generation (SHG) for 177.3/193.7 nm DUV lasers, which is almost identical to that of KBBF. Remarkably, BEBO shows an excellent DUV SHG capacity and an even shorter phase‐matching wavelength than KBBF. Therefore, the newly discovered vdW BBH and BEBO, once verified by experiments, could provide an ideal platform to study DUV NLO effects in three dimensions and two dimensions. [ABSTRACT FROM AUTHOR]

Sodium‐based layered oxide cathodes are competitive candidates for commercial sodium‐ion batteries owing to their high theoretical capacities, low costs, and simple synthesis. P3‐type layered oxides with large open channels enable fast Na+ transport and hence good rate performance. However, the lower crystal symmetry of P3‐type oxides and variation of Na+ contents in the Na layer during desodiation/sodiation lead to large electrostatic repulsion changes between TMO2 slabs (TM=Transition Metal), resulting in irreversible phase transitions, and fast performance degradation. Herein, a potential Na+ conductor Na2SeO4 is first found that it can be easily in situ grown on P3‐Na0.45Ni0.2Mn0.8O2 to form a novel heterostructure P3‐Na0.45Ni0.2Mn0.8O2/Na2SeO4. The synergy between P3‐Na0.45Ni0.2Mn0.8O2 and Na2SeO4 functions in promoting Na+ diffusion and suppressing P3‐O3 phase transitions upon deep sodiation, which results in recorded high‐rate capability (68.2% capacity retention with retained 83.9 mAh g−1 capacity at 6400 mA g−1) and superior cycling stability (capacity retention 75% after 1000 cycles) among all reported P3‐type cathodes. Thus, it is believed that this novel heterostructure design opens a new pathway to promote practical applications for layered oxide cathodes in sodium‐ion batteries. [ABSTRACT FROM AUTHOR]

This study compares three zircon synthesis techniques (synthesis, high-temperature and high-pressure sintering and fast hot-pressing sintering) for the preparation of reference materials for Hf isotope analysis of zircon by laser ablation multi-collector inductively-coupled plasma mass spectrometry (LA-MC-ICP-MS). Ultrafine milled zircon powder particles doped with Yb2O3 produced by wet milling were used to synthesize zircon samples by using high-temperature and high-pressure sintering and fast hot-pressing sintering techniques. Li–Mo flux was necessary to obtain synthetic zircon grains. Zr signals for synthetic zircon grains and high-temperature and high-pressure sintered zircon are consistent with those of natural zircons but higher than that of fast hot-pressing sintered zircon, indicating that high-temperature and high-pressure sintered zircon has approximated the theoretical maximum density due to high pressure. The Hf isotopic compositions of high-temperature and high-pressure sintered and fast hot-pressing sintered zircon are comparable to those of the initial starting materials, whereas the Hf isotopes in synthetic zircon grains deviate slightly from those of the initial Hf solution. Compared with Hf isotope ratios obtained by SN-MC-ICP-MS, all preparation techniques give reliable LA-MC-ICP-MS results, suggesting that all synthetic zircon samples have great potential as both tools for in situ method development and isotopic reference materials. [ABSTRACT FROM AUTHOR]

With the popularization of steel fiber reinforced concrete (SFRC), research on the packing of steel fiber-aggregate (F-A) mixtures has become a significant prerequisite for the mix design of SFRC. Although the compressible packing model (CPM) can be used to predict the packing density (PD) of F-A mixtures, its interaction coefficients are determined from the elementary particle classes without fibers (narrow particle size distribution), which limits the applicability of the CPM. In this study, after adding steel fibers to binary aggregate with wide particle size distribution, the PDs of steel fiber-binary aggregate (F-BA) mixtures were measured. The method of establishing interaction coefficients for F-A mixtures was modified, and the general formulas of interaction coefficients were proposed. The novel CPM model after comprehensive corrections of fiber disturbance parameter and interaction coefficients for F-A mixture was established. Compared with the conventional CPM, the prediction accuracy of novel CPM was greater. [Display omitted] • The effect of aggregate combinations and steel fiber combinations on packing density evolution was studied. • Corrections of fiber disturbance parameter and interaction coefficients in Compressible Packing Model were proposed. • The novel CPM was developed for packing density prediction of steel fiber-binary aggregate mixtures. • The novel CPM can be applied to aggregate with large particle classes. [ABSTRACT FROM AUTHOR]

• Ultrahigh through-plane thermal conductivity achieved by continuous carbon fibers. • Thermal-induced and slant slicing-induced flexibility. • Leakage proof capacity from polymer skeleton and carbon fiber arrays. • Novel thermal management capacity from high through-plane thermal conductivity and heat absorbed during phase change. With the rapid development of micro-nano electronics, thermally conductive materials with remarkable through-plane thermal conductivity (κ ⊥) and great flexibility are greatly urgent to effective thermal management. The fillers with high thermal conductivity (TC) are commonly assembled to achieve this target. However, the imperfect contact between the joint fillers will lead to high thermal resistance (R), hindering thermal transport. Herein, we fabricated thermal interface materials (TIMs) with ultra-high κ ⊥ (up to 168.4 W m−1 K−1) and adjustable flexibility by the combination of highly thermally conductive carbon fiber bundles (CF) and polymer encapsulated phase change materials (PCMs). The alignment of consecutive CF guarantees the continuity of thermal paths, greatly facilitating thermal transport. While the slantly slicing technique and softening effect of PCMs beyond phase transition temperature lead to an attenuated compression stress (1.6 MPa@10% strain with a CF loading of 50 wt%). What's more, the latent heat absorbed by PCMs is also conducive to thermal management. Thus, during a CPU temperature-control experiment, the application of as-prepared TIMs manifests a temperature decline of 33.9 °C of CPU. This work opens a new perspective to fabricating TIMs with ultrahigh κ ⊥ and low compression stress (σ) by the combination of thermally induced flexible matrix and the slantly slicing technique of aligned CFs. [ABSTRACT FROM AUTHOR]

Shear horizontal (SH) waves are widely used in the non-destructive evaluation and structural health monitoring fields. Conventional periodic permanent magnet electromagnetic acoustic transducers (PPM EMAT) can generate a single SH wave mode, which propagates in both forward and backward directions. Generation in a single direction is usually preferred to ease signal interpretation and increase inspection reliability. Recently, we have proved that a single, either fundamental or high-order, SH wave mode can be unidirectionally generated using a dual PPM EMAT, with carefully designed driving signals. Distinct SH modes present different applicability due to their particular response to features in the structure, such as defects. Hence, unidirectional generation of two different SH modes simultaneously with a dual-array transducer is investigated in this paper. The selectivity of wave modes and the selectivity of the propagation direction are studied by combining pure wave mode excitability with the superposition of optimal excitation signals for unidirectional generation, addressed in the frequency–wavenumber domain. Excitation signals for optimal and simultaneous generation of the SH0 and SH1 modes propagating in the same direction or in opposite directions have been designed. Experiments on an aluminium plate have demonstrated that the two wave modes can be effectively simultaneously generated with only one dual-array transducer and the propagation direction of each wave mode can be flexibly controlled using the designed excitation signals. • A single dual-array transducer excites distinct unidirectional waves simultaneously. • Pure wave excitation and direction are addressed in the frequency–wavenumber domain. • Superposition of optimal excitation signals ensures simultaneous wave generation. • A dual PPM-EMAT simultaneously generated SH0 and SH1 modes in distinct directions. • The generation direction of each wave mode can be conveniently controlled. [ABSTRACT FROM AUTHOR]

Steel fiber can significantly improve the tensile strength, toughness, and crack resistance of concrete matrix, but there is limited research on the packing of single steel fiber-aggregate (SF-A) and hybrid steel fiber-aggregate (HF-A) mixtures. To investigate the effect of steel fibers on the packing of aggregates, the loosely-packed packing density (PD) of 36 SF-A mixtures and 36 HF-A mixtures was measured via the high-rigidity container. The results indicated that the PD always decreased with increasing fiber volume regardless of single or hybrid steel fibers and the size ratio of steel fiber to aggregate particle was a crucial parameter affecting this lowering effect. Moreover, a novel prediction model considering the relative size of fiber and aggregate as key factors was developed and the synergistic effect on aggregates by hybrid fibers was also incorporated into the model. Prediction errors less than 1% were evaluated after calibrating the model parameters. [Display omitted] • The packing rules of the steel fiber-aggregate mixtures are clarified. • A synergistic effect of hybrid steel fibers on aggregate is proposed. • The calculation method for the fiber disturbance factor is modified. • A prediction model of packing density for single and hybrid steel fiber-aggregate mixtures is presented. [ABSTRACT FROM AUTHOR]

• Effective and low-consumption finishing strategy for multifunctional stainless steel mesh and sponges. • Superhydrophobic coating with micro/nano structures is rationally constructed without organic solvents. • Rational water-based aza-Michael addition reaction coating strategy realizes on-demand special wettability. Superhydrophobic porous materials are widely used in oil-water separation due to their water-blocking and oil-passing properties. However, the preparation of most superhydrophobic porous materials is generally energy-intensive and must be performed using organic solvents. In this study, we describe a straightforward and cost-effective strategy for fabricating superhydrophobic coatings on nanosized soil particle-modified stainless steel mesh (SSM). The coating is prepared via the aza-Michael reaction of stearyl acrylate and melamine-urea–formaldehyde (MUF) resin catalysed by methyl cyclodextrin in water. Superhydrophobic meshes with water contact angles (WCAs) exceeding 150° are obtained, exhibiting extraordinary water repellency. The superhydrophobic mesh also effectively prevents surface contamination, creating a self-cleaning surface that is both waterproof and dustproof. Most importantly, the superhydrophobic mesh presents excellent oil separation performance for oil-water mixtures of various compositions, maintaining extremely high separation efficiency (>98%) even after 80 cycles. Additionally, we successfully apply this strategy to the preparation of superhydrophobic melamine sponges with excellent oil adsorption capacity (17.6–44.2 g/g). This innovative study provides an effective strategy for designing biomimetic superhydrophobic surfaces and is a promising development in the field of environmentally friendly oil-water separators. [ABSTRACT FROM AUTHOR]

With the rapid development of the electronics industry, there is a growing demand for packaging materials that possess both high thermal conductivity (TC) and low electrical conductivity (EC). However, traditional insulating fillers such as boron nitride, aluminum nitride, and alumina (Al2O3) have relatively low intrinsic TC. When graphene, which exhibits both superhigh TC and EC, is used as a filler to fill epoxy resin, the TC of blends can be much higher than that of blends containing more traditional fillers. However, the high EC of graphene limits its application in cases where electrical insulation is required. To address this challenge, a method for coating graphene sheets with an in situ grown Al2O3 layer has been proposed for the fabrication of epoxy-based composites with both high TC and low EC. In the presence of a cationic surfactant, a dense Al2O3 layer with a network structure can be formed on the surface of graphene sheets. When the total content of Al2O3 and graphene mixed filler reached 30 wt%, the TC of the epoxy composite reached 0.97 W m−1 K−1, while the EC remained above 1011 Ω·cm. Finite element simulations accurately predicted TC and EC values in accordance with experimental results. This material, with its combination of high TC and good insulation properties, exhibits excellent potential for microelectronic packaging applications. [ABSTRACT FROM AUTHOR]

[Display omitted] • Magmatism formed during the initial stage (ca. 480Ma) and advanced stage (ca. 450Ma) of exhumation of subducted continental crust have been recognized in South Altyn western China. • Two stages of magmatism exhibits evidence for the partial melting of subducted continental crust during differential exhumation process of South Altyn in Palaeozoic. The early Palaeozoic continental subduction–collisional belt in South Altyn (SA) western China distributes a large amount of (ultra)-high-pressure ((U)HP) metamorphic and granitic rocks associated with subduction, collision, and exhumation. In this study, four granitic rocks were collected from Bashenwake located in eastern SA. The ages of the garnet-bearing alkali-feldspar granite (GAFG), garnet-bearing granitic gneiss (GGG), alkali-feldspar granite (AFG), and syenogranite (SG) are 458.0 ± 4.1, 483.0 ± 4.1, 450.0 ± 2.4, and 482.0 ± 4.9 Ma, respectively. Whole-rock major and trace elements and Sr–Nd–Pb isotope, and zircon Hf isotope compositions for all samples exhibit characteristics of a continental crustal source. Based on partial melting modeling, the source temperature of the GGG, GAFG, AFG and SG was concluded as 750–780 °C, 730–760 °C, 730–770 °C and ca. 800 °C, respectively. The source pressure was estimated as ca. 0.8 GPa for the GGG, GAFG and AFG, and ca. 1.2 GPa for SG. Combined with studies on (U)HP metamorphic rocks in SA, this study reveals that GGG is formed by metamorphism while SG is formed from partial melting of upper crustal rocks heated by upwelling mantle during the initial stage of exhumation (ca. 480 Ma) of subducted continental crust in SA. During further stage of exhumation of the subducted continental crust at ca. 450 Ma, the GAFG and AFG were formed from partial melting of GGG as a result of decreased pressure and further mantle upwelling. Consequently, the exhumation age of subducted continental crust in eastern SA is ca. 30 Myr earlier than that in western SA. Thus, the geochronology and petrogenesis of four granitic samples in this study exhibit one of very few evidence for partial melting of subducted continental crust during the exhumation and also provide magmatism exhibits evidence for the differential exhumation model of eastern SA in Palaeozoic. [ABSTRACT FROM AUTHOR]

A superhydrophobic coating composed of epoxy on the bottom and siloxane-modified silica on the top was prepared by employing the scraping and spraying methods. The superhydrophobic coating possesses excellent mechanical properties, is superhydrophobic (water contact angle, WCA = 164.3°), and has low adhesion. The long-term corrosion resistance of the epoxy coating and the superhydrophobic coating in a 3.5 % NaCl solution and hydrogen sulfide environment was assessed using electrochemical impedance spectroscopy (EIS), polarization curve analysis, immersion testing, and X-ray diffraction (XRD). Test results indicate that the superhydrophobic coating has excellent anti-corrosion capability in an H 2 S environment for 50 days and in a 3.5 % NaCl solution for 60 days. This is of great significance for developing the potential applications of superhydrophobic coatings in H 2 S environments. [Display omitted] • Epoxy resin and superhydrophobic surface combination for carbon steel substrate protection. • The coating showed anticorrosive effect in 3.5 % sodium chloride solution. • Superhydrophobic surface has excellent corrosion resistance in H 2 S environment of alternating temperatures and humidities. [ABSTRACT FROM AUTHOR]

Phase change materials (PCMs) are potential candidates in passive thermal regulation and energy storage fields due to their high latent heat capacity around phase transition temperature. However, the leakage problem and low thermal conductivity are two obstructive factors for the extended application of PCMs. Herein, a series of paraffin@silicon dioxide microcapsules (Pa@SiO 2)/graphene sheets (GS)/silicone rubber (SR) phase change composites (PCCs) were prepared. It is found that the inorganic SiO 2 shell is conducive to enhancing the thermal conductivity of PCCs and the double encapsulation by the SiO 2 shell and SR skeleton can restrict the leakage of liquid Pa during phase transition. With a Pa@SiO 2 content of 70 wt%, the PCCs have a high latent heat of 126.1 J/g and enhanced thermal conductivity of 0.37 W m−1 K−1, which is 131.25% higher compared to that of pure SR. In addition, the introduction of graphene sheets further boosts the thermal conductivity of PCCs to 2.69 W m−1 K−1. The obtained PCCs lead to a surprising temperature decline of nearly 35 °C of a commercial lithium-ion battery during a high discharge rate (7.4 C). This work provides an efficient route to fabricate microcapsules-based PCCs for passive thermal regulation. [Display omitted] [ABSTRACT FROM AUTHOR]

As a symbolic ceramic oxide, the reaction of SiO 2 as an insulating layer with the Fe–Si–Al/SiO 2 soft magnetic composites (SMCs), substrate during heat treatment, as well as the resulting microscopic phase transition of the core–shell structure and its influence on the magnetic properties, are worth investigating. In this study, based on the successful synthesis of Fe–Si–Al based SMCs using fluidised chemical vapour deposition combined with an electric hot–press sintering method, the evolution of the insulating layers was investigated under different heat–treatment temperatures and closely linked to the magnetic performance of the composites. During heat treatment at high temperatures, the formation of high–resistivity oxides (Al 2 O 3) after heat treatment results in a low inter–particle eddy current loss, while excessive temperature causes disintegration of the core–shell heterostructure. This leads to a discernible increase in eddy current and hysteresis losses and a decrease in permeability and resistivity. The SMCs had an Ms of 115.8 emu/g, a resistivity of 6.86 mΩ cm, and a hysteresis loss of 56.3 kW/m3 at 10 mT and 100 kHz when heat-treated at 1373 K for 120 min, which was the best among all samples. This research provides a novel approach to building SMCs with inorganic ceramic insulating layers and a comprehensive understanding of the relationship between the heat–treatment process parameters, microstructure, and magnetic properties which is highly significant for industrial production. [Display omitted] [ABSTRACT FROM AUTHOR]

• Novel adaptation of transformers for handwriting recognition tasks, bypassing recurrent neural nets. • Competitive results achieved in low resource scenario with synthetically pretrained model. • Extensive ablation and comparative studies conducted to understand and modify transformer properly for HTR. • Implicit language modelling ability proved. • The state-of-the-art performance achieved on public IAM dataset. The advent of recurrent neural networks for handwriting recognition marked an important milestone reaching impressive recognition accuracies despite the great variability that we observe across different writing styles. Sequential architectures are a perfect fit to model text lines, not only because of the inherent temporal aspect of text, but also to learn probability distributions over sequences of characters and words. However, using such recurrent paradigms comes at a cost at training stage, since their sequential pipelines prevent parallelization. In this work, we introduce a novel method that bypasses any recurrence during the training process with the use of transformer models. By using multi-head self-attention layers both at the visual and textual stages, we are able to tackle character recognition as well as to learn language-related dependencies of the character sequences to be decoded. Our model is unconstrained to any predefined vocabulary, being able to recognize out-of-vocabulary words, i.e. words that do not appear in the training vocabulary. We significantly advance over prior art and demonstrate that satisfactory recognition accuracies are yielded even in few-shot learning scenarios. [ABSTRACT FROM AUTHOR]

Array transducers are commonly used to generate several types of waves, such as ultrasonic guided waves. They consist of a series of periodic wave source elements, and thus define a nominal or dominant wavelength of generated waves. A common approach to generating waves in a single direction is to use two identical wave sources, or two arrays of sources forming a dual-array transducer, that are separated by a quarter wavelength. Then, one source is activated a quarter of a time period after the other. In this way, constructive interference arises in one direction, whilst destructive interference arises in the opposite direction, making the total wave source unidirectional. This principle assumes that the frequency content of the generated wave is monochromatic. When there is some frequency bandwidth to the wave generated, such as with finite-length pulses, one cannot satisfy simultaneously constructive and destructive interference in opposite directions with dual-array transducers. For a non-dispersive wave mode, ideal destructive interference for pulsed waveform is obtained if one of the sources is inverted relative to the other, so that, in theory, complete cancellation can be achieved. Moreover, most guided wave modes are dispersive, meaning that, different frequencies propagate at different phase speeds. This limits the amount of wave cancellation in one direction and constructive interference in the other. Here, we describe the operation of the dual-array transducer in the frequency–wavenumber domain and use it to propose two new excitation methods, based on a frequency-dependent phase-shift strategy, that is designed through the dispersion relationship of the wave mode of interest. These provide ideal constructive or destructive interferences for dispersive waves, and achieve optimal unidirectional generation behaviour for dispersive wave modes. The new methods were experimentally assessed with shear horizontal ultrasonic waves, generated by a dual periodic permanent magnet electromagnet acoustic transducer. The optimal excitation signal yielded up to 30 dB unidirectionality, when generating the dispersive SH1 wave mode in an aluminium plate. • Unidirectional wave generation is addressed in the frequency–wavenumber domain. • Usual time-delay excitation methods were proved not appropriate for dispersive waves. • We propose a method that optimally generates dispersive waves unidirectionally. • A dual PPM-EMAT was used to generate shear horizontal waves in a single direction. • About 30 dB unidirectionality was achieved for the dispersive SH1 mode experimentally. [ABSTRACT FROM AUTHOR]

Array transducers can allow wavelength and frequency selectivity and can be used to generate different types of waves, such as ultrasonic bulk or guided waves. Dual-array transducers consist of two interlaced arrays, where the elements of each array are electrically connected. Therefore, by driving each array with a pair of phased pulses one can achieve a degree of wave generation control that allows unidirectional generation, unlike single array transducers that generate waves in both 0° and 180° directions with respect to the array's longitudinal axis. In this paper, we present a one-dimensional analytical model to determine the ultrasonic waves generated by dual-array transducers based on the excitability of the array in the frequency–wavenumber domain, the so-called operation region, determined by the joint spatial and temporal spectrum of the dual-array. We further exploited it to analyse the effectiveness of unidirectional generation with time-delayed excitation signals that provide ideal constructive or destructive interferences. The model also provides the time-domain received waveforms, which were compared to experimentally generated shear-horizontal ultrasonic guided waves, with a dual periodic permanent magnet array electromagnetic acoustic transducer, showing very good agreement. The adequate selection of the excitation signal allowed one to obtain up to about 40 dB unidirectionality experimentally. • Dual-array transducers are modelled in the frequency–wavenumber domain. • The interference mechanism of two types of time-delayed pulses is analysed. • A Dual-PPM EMAT is used to experimentally generate SH guided waves unidirectionally. • Model-predicted time-domain signals and experimental ones show excellent agreement. • About 40 dB unidirectionality was achieved with the ideal excitation pulses. [ABSTRACT FROM AUTHOR]

Cellulose nanofibrils (CNF) films are generally regarded as promising alternatives for non-biodegradable plastics films. However, the shortcomings of high hydrophilic performance, low elongation and poor folding endurance continue to pose challenges in commercial application. In the present study, we established controllable reflectance CNF films by applying a facile and scalable poly (butylene adipate-co-terephthalate) (PBAT)/SiO 2 nanoparticles (NPs) reinforced strategy in a free chemical modification manner. CNF/PBAT films have the favorable combination of hydrophobicity, elongation and folding endurance. The results reveal a significant improvement in the hydrophobic properties of CNF/PBAT films (water contact angle >80°), as well as a 3 times improvement in folding resistance (1210 cycles), a 3.7 times improvement in tensile strength (89.8 MPa) and controlled reflectance properties. Additionally, we examined the hiding power and color difference of the CNF/PBAT films, and explored the underlying principle for the enhanced hydrophobicity, folding resistance, elongation and reflectance. Finally, the CNF/PBAT films exhibited stable comprehensive performance after we applied the films in drinking straws. The present study provides a facile strategy to prepare hydrophobic, folding resistant, reinforced and reflectance-controlled CNF films and could promote industrial use in the fields of glass film, beverage appliances, packaging, and flexible electronic devices. [Display omitted] • Increasing the layer spacing and porosity of CNF films by mixing with SiO2. • Mechanical, elongation, folding and reflectance properties of prepared composite improved markedly. • CNF/PBAT films display a controlled adjustment in reflectance, hiding power, and color difference. • CNF/PBAT films provide stability for packaging, electronics and other advanced applications. [ABSTRACT FROM AUTHOR]

A non-Darcy flow with moving boundary conditions in a low-permeability reservoir was solved using the homotopy analysis method (HAM), which was converted into a fixed-boundary mathematical model via similarity transformation. Approximate analytical solutions based on the HAM are guaranteed to be more accurate than exact analytical solutions, with relative errors between 0.0089% and 2.64%. When λ = 0, the pressure drop of the Darcy seepage model could be instantaneously transmitted to infinity. When λ > 0, the pressure drop curve of the non-Darcy seepage model exhibited the characteristics of tight support, which was clearly different from the Darcy seepage model's formation pressure distribution curve. According to the results of the HAM, a moving boundary is more influenced by threshold pressure gradients with a longer time. When the threshold pressure gradients were smaller, the moving boundaries move more quickly and are more sensitive to external influences. One-dimensional, low-permeability porous media with a non-Darcy flow with moving boundary conditions can be reduced to a Darcy seepage model if the threshold pressure gradient values tend to zero. [ABSTRACT FROM AUTHOR]

• Melamine modified carbon dots (Me-CDs) exhibits 92.36% corrosion inhibition efficiency on carbon steel in neutral medium. • Adsorption isotherm of Me-CDs conforms to Temkin adsorption model, involving both chemisorption and physisorption. • Hydrophobic Me-CDs film adheres on carbon steel via coordinate-covalent bond and multilayer accumulation effect. Melamine modified carbon dots (Me-CDs) was synthesized by hydrothermal method and used as effective corrosion inhibitor for Q235 carbon steel in 3.5 wt% sodium chloride (NaCl) solution. The microstructure and surface properties of Me-CDs were characterized using XRD, FTIR, XPS and TEM. The corrosion inhibition behavior and mechanism of Me-CDs for carbon steel were investigated using weight loss and electrochemical methods, in combination with some surface characterizations (including SEM, AFM and contact angle tester). Results showed that Me-CDs as mixed-type adsorbent inhibitor could effectively prevent carbon steel from corrosion, and the maximum corrosion inhibition efficiency can reach 92.36% at 200 mg/L. The absorption of Me-CDs conformed to Temkin adsorption model, involving both chemisorption and physisorption. Based on the results of characterization analysis, the chemisorption from multiple adsorption centers, physisorption by blocking and barrier effect, and the formation of hydrophobic film on the surface of carbon steel was proposed to clarify the corrosion inhibition mechanism of Me-CDs. [ABSTRACT FROM AUTHOR]

A novel strategy for spraying nanosized soil particles on steel mesh to prepare the superlyophobic soil mesh by a facile surface treatment technology, and successfully apply it to various immiscible liquids separation. [Display omitted] • A multifunctional, sustainable material for immiscible liquid mixtures separation. • Under nonpolar (polar) liquid superlyophobicity of polar (nonpolar) liquid. • Used chemical properties-structure relationships to give material performance. • Low cost manufacturing, environment friendly, dimplicity of operator. • Good corrosion resistance in acidic, alkaline and high salt environment. Immiscible liquids separation has recently become a worldwide challenge due to the expanding industrial activity. It is still thorny to put forward a universal strategy for constructing multi-superlyophobic surfaces in immiscible liquids systems due to a thermodynamic contradiction. Herein, a low-cost, environmentally friendly pre-wetted nanosized soil coated-mesh (NSCM) was prepared, which shows the property of under-nonpolar-liquid superlyophobic to polar liquid, or under-polar-liquid superlyophobic to nonpolar liquid. The NSCM was fabricated in aqueous solutions by spraying melamine formaldehyde resin modified nanosized soil particles on a stainless-steel mesh for selective immiscible liquid separation. After the NSCM is prewetted with heavy liquid, heavy liquid can be removed from the light immiscible liquid mixtures by gravity. The as-prepared NSCM showed a high separation efficiency of above 99% for a series of immiscible liquids mixtures, even after 60 separation cycles. More importantly, the electrochemical tests indicated that the NSCM exhibited the outstanding durability after being immersed in alkali (pH = 10.0, NaOH), acidic (pH = 4.0, HCl) and high-concentrated salt solutions (3.5 wt% NaCl) for 30 days. The calculated R t values were approximately 1.04 × 107, 2.65 × 106 and 7.59 × 105 Ω·cm2, respectively. And the corresponding corrosion rates were 0.013712, 0.96438, and 2.5818 μm/year, respectively. These excellent performances of the NSCM make it an ideal candidate material for separation, and even in a wider field of sea wastewater treatment. [ABSTRACT FROM AUTHOR]

• Single crystal structure of a novel ultraviolet NLO tourmaline was solved. • Sellmeier equations were obtained by fitting the measured refractive indices. • Phase matching range of the title crystal is obtained from the Sellmeier equations. • The linear and NLO properties were investigated by the experimental and theory calculation. Transparent tourmaline NaAl 9 (BO 3) 3 Si 6 O 21 OH is first reported by combining experimental and theory calculation methods, which exhibits potential ultraviolet nonlinear optical properties. [Display omitted] Tourmaline, as an important mineral, has received intensive interest, since it is not only a valuable gemstone, but also is a piezoelectric or pyroelectric material, due to the polar structural configuration. However, its nonlinear optical (NLO) properties were not explored so far, because a transparent crystal with high transmittance is scarce, being essential to optical functional materials. Here, we report a novel ultraviolet (UV) NLO tourmaline crystal with chemical composition NaAl 9 (BO 3) 3 Si 6 O 21 OH for the first time by combining first-principles analysis and experimental measurements. It exhibits a short UV absorption edge, considerable second harmonic generation effect and moderate birefringence, thereby facilitating its phase-matching coherent beam output in the range from visible to UV regions. [ABSTRACT FROM AUTHOR]