Search

With the rapid development of the Internet of Things (IoTs), wearable sensors are playing an increasingly important role in daily monitoring of personal health and wellness. The signal-to-noise-ratio has become the most critical performance factor to consider. To enhance it, on the one hand, good sensing materials/devices have been employed; on the other hand, signal amplification and noise reduction circuits have been used. However, most of these devices and circuits work in an active sampling mode, requiring frequent data acquisition and hence, entailing high-power consumption. In this scenario, a flexible and wearable event-triggered sensor with embedded signal amplification without an external power supply is of great interest. Here, we report a flexible two-terminal piezotronic n-p-n bipolar junction transistor (PBJT) that acts as an autonomous and highly sensitive, current- and/or voltage-mediated pressure sensor. The PBJT is formed by two back-to-back piezotronic diodes which are defined as emitter-base and collector-base diodes. Upon force exertion on the emitter side, as a result of the piezoelectric effect, the emitter-base diode is forward biased while the collector-base diode is reverse biased. Due to the inherent BJT amplification effect, the PBJT achieves record-high sensitivities of 139.7 kPa-1 (current-based) and 88.66 kPa-1 (voltage-based) in sensing mode. The PBJT also has a fast response time of <110 ms under exertion of dynamic stimuli ranging from a flying butterfly to a gentle finger touch. Therefore, the PBJT advances the state of the art not only in terms of sensitivity but also in regard to being self-driven and autonomous, making it promising for pressure sensing and other IoT applications. [ABSTRACT FROM AUTHOR]

An analog pulse‐width‐modulation (A‐PWM) Micro‐LED (μLED) pixel circuit based on low‐temperature‐polysilicon (LTPS) thin‐film transistors (TFTs) for mobile displays is proposed. The progressive‐emission mode is implemented using a single Sweep (SW) signal by in‐pixel logic operation circuits. By adjusting the emission time of the progressive‐emission mode, the μLED is biased with the maximum quantum efficiency (EQE). Consequently, the static power consumption of proposed pixels is reduced by 29.2%, compared with conventional schemes. [ABSTRACT FROM AUTHOR]

A compact gate driver using p‐type low‐temperature polycrystalline silicon (LTPS) thin‐film transistors (TFTs) was proposed for Micro‐Light Emitting diodes (μLEDs) display using progressive emission analog pulse‐width modulation (A‐PWM) approach. The gate driver contains a simple waveform shaping module and outputs multiple sweep signals, including SW[n], EM[n], and S[n], by reusing the bootstrap node. Compared with conventional schemes, the proposed gate driver renders static power consumption reduction of the μLED display by 29.2%. [ABSTRACT FROM AUTHOR]

This paper studies high‐resolution AMOLED displays pixel and driving circuits using 3D stacking LTPS and oxide hybrid TFT integration technology systematically. It is demonstrated the OLED display resolution reaches 1167 PPI when the minimum line width/line spacing is reduced to 1 μm/0.5 μm. In addition, peripheral row and column drive circuits for the high display resolution were also illustrated. Good dynamic performance of the designed driving circuits was obtained thanks to the 3D TFTs. [ABSTRACT FROM AUTHOR]

This paper presents a PAM and PWM combined Mini‐LED pixel circuit based on oxide TFTs. In the PAM part, a constant current (1mA) allows Mini‐LEDs work at peak efficiency and reduce power consumption. A source follower structure compensates for ΔVTH and VSS IR rise, which has only one TFT on current path, so that the pixel circuit works at low voltage. In the PWM part, a diode connected structure compensates for ΔVTH. Simulation results show that the current error rate is less than 0.81% when ΔVTH of PAM part is within ±3 V. When VSS rises less than 3 V, the current error rate is less than 7.22%. When ΔVTH of PWM part is +3 V, emission time variation is reduced by 99.29% compared with the circuit without compensation. The supply‐voltage can be reduced from 19.7 V to 15 V thanks to the proposed Mini‐LED pixel circuit. [ABSTRACT FROM AUTHOR]

Featured Application: In order to meet the camouflage requirements for various applications, with different climates conditions of full-time, this paper proposes an adaptive real-time camouflage control system in the visible light band. The sensor technology, image processing technology, and display technology are well combined by this camouflage control system. This paper presents an adaptive camouflage system in visible band, featuring a dominant color feature-matching algorithm and pulse width modulation (PWM)-based display driving circuit. The control system consists of three parts, namely, the background sensing part, the central processing part, and the physical driving waveform generation part. Images of the local environment are sampled by the background sensing part, and then the dominant color feature matching algorithm is conducted to select a proper camouflage image that matches the local environment. Consequently, the cholesteric liquid crystals (CLCs) display using amplitude adjustable AC voltage, which is modulated by the physical driving waveform generation unit. The experimental results show that the matching degree of the proposed algorithm was 2.47 times that of the conventional hue (H), saturation (S), and value (V) histogram camouflage evaluation method, while the output peak wavelength of the reflective band can be adjusted from 604 to 544 nm according to the ambient color profile. [ABSTRACT FROM AUTHOR]