Search

Atmospheric aerosols impact the Earth's climate system directly by scattering and absorbing solar radiation, and it is important to characterise the aerosol optical properties in detail. This study reports the development and validation of an airborne dual-wavelength cavity-attenuated phase-shift (CAPS) single monitor, named A2S2 (Aerosol Absorption Spectral Sizer), based on the commercial CAPS single-scattering albedo monitor (CAPS-PM SSA ; Aerodyne), to simultaneously measure the aerosol optical scattering and extinction at both 450 and 630 nm wavelengths. Replaced pressure and temperature sensors and an additional flow control system were incorporated into the A2S2 for its utilisation on board research aircraft measuring within the troposphere. The evaluation of A2S2 characteristics was performed in the laboratory and included the investigation of the signal-to-noise ratio, validation of performance at various pressure levels, optical closure studies and intercomparing with the currently validated techniques. The chamber experiments show that the A2S2 can perform measurements at sample pressures as low as 550 hPa and at sample temperatures as high as 315 K. Based on the Allan analysis results, we have evaluated that the minimum detection limit of the measurements shows that the measurements have a limit accuracy of ∼ 2 Mm-1 at 450 nm and ∼ 1 Mm-1 at 630 nm for 1 Hz measurements of both scattering coefficients (σsca) and extinction coefficients (σext). The optical closure study with size-selected polystyrene latex (PSL) particles shows that the truncation error of the A2S2 is negligible for particles with particle volume diameter (Dp) < 200 nm, while, for the larger sub-micrometre particles, the measurement uncertainty of A2S2 increases but remains less than 20 %. The average factors to correct the truncation error are 1.13 and 1.05 for 450 and 630 nm, respectively. A simplified truncation correction, dependent on the scattering Ångström exponent (SAE), was developed to rectify truncation errors of the future A2S2 field measurement data. The σsca and σext measured by the A2S2 show good agreement with the concurrent measured results from the nephelometer and the CAPS particle extinction monitor (CAPS-PM ex). The absorption coefficient (σabs) derived through the extinction-minus-scattering (EMS) method by the A2S2 also corresponds with the results obtained from the aethalometer. The A2S2 was successfully deployed during an aircraft measurement campaign (Atmospheric ChemistRy Of the Suburban foreSt – ACROSS) conducted in the vicinity of Paris and the surrounding regions. The average SSA measured during the entire ACROSS flight campaign is 0.86 and 0.88 at 450 and 630 nm, respectively, suggesting that light-absorbing organic aerosols play a significant role. The average SAE and absorption Ångström exponent (AAE) varied due to measurements in various pollution conditions. The results presented in this study indicate that the A2S2 instrument is reliable for measuring aerosol σsca and σext at both blue and red wavelengths, and it stands as a viable substitute for future airborne evaluations of aerosol optical properties. [ABSTRACT FROM AUTHOR]

Atmospheric aerosols impact the Earth’s climate system directly by scattering and absorbing solar radiation, and it is important to characterise the aerosol optical properties in detail. This study reports the development and validation of an airborne dual-wavelength cavity-attenuated phase shift-single (CAPS) monitor, named A2S2 (Aerosol Absorption Spectral Sizer) based on the commercial CAPS single scattering albedo monitor (CAPS-PMSSA, Aerodyne), to simultaneously measure the aerosol optical scattering and extinction at both 450 nm and 630 nm wavelengths. New pressure and temperature sensors and an additional flow control system were incorporated into the A2S2 for its utilization onboard research aircraft measuring within the troposphere. The evaluation of A2S2 characteristics was performed in the laboratory and included the investigation of the signal-to-noise ratio, validation of performance at various pressure levels, optical-closure studies and intercomparing with the currently validated techniques. These laboratory characterisation experiments show that the A2S2 can perform measurements at sample pressures as low as 550 hPa and at sample temperatures as high as 315 K, with an uncertainty of 1 Mm-1 at 450 nm and 0.3 Mm-1 at 630 nm for 1 Hz measurements of both scattering coefficients (σsca) and extinction coefficients (σext). The optical-closure study with size-selected polystyrene latex (PSL) particles show that the truncation error of the A2S2 is negligible for particles with particle volume diameter (Dp) < 200 nm, while for the larger sub-micrometre particles, the measurement uncertainty of A2S2 increases but remains less than 20 %. The A2S2 shows good agreement with the validated instruments for the σsca and σext at 450 nm and 630 nm. The A2S2 was successfully deployed during an aircraft measurement campaign (ACROSS) conducted in the vicinity of Paris and the surrounding regions. The average SSA measured during the entire ACROSS flight campaign is 0.86 and 0.88 at 450 nm and 630 nm, respectively, while the Scattering Ångström Exponent (SAE) varies due to measurements in various pollution conditions. The A2S2 measured σsca results exhibit overall good agreement with the nephelometer results, and it successfully produced altitude profile results over the varied background conditions. The results presented in this study indicate that the A2S2 instrument is reliable for measuring aerosol σsca and σext at both blue and red wavelengths, and it is suitable to replace the nephelometer onboard for future aircraft campaigns. [ABSTRACT FROM AUTHOR]

Aerosol intensive optical properties, including Ångström exponents for aerosol light extinction (EAEs), scattering (SAEs) and absorption (AAEs) as well as and the single-scattering albedo (SSA), are indicators for aerosol size, chemical composition, radiative behaviour and particle sources. Derivation of these parameters requires the measurement of aerosol optical properties at multiple wavelengths, which usually involves the use of several instruments. Our study aims to quantify the uncertainties in the determination of these intensive properties using an optical closure approach. In our laboratory closure study, we measured the full set of optical properties for a range of light-absorbing particles with different properties externally mixed with ammonium sulfate to generate aerosols with controlled SSA values. The investigated absorbing particle types were fresh combustion soot emitted by an inverted flame soot generator (SOOT; fractal agglomerates), Aquadag (AQ; compact aggregates), Cabot black (BC; compact agglomerates) and an acrylic paint (magic black, shape unknown). The instruments used in this study were two cavity attenuated phase shift particle monitors for single-scattering albedo (CAPS PM SSA 's; λ=450 , 630 nm) for measuring light-extinction and light-scattering coefficients, one integrating nephelometer (λ=450 , 550, 700 nm) for light-scattering coefficients, and one tricolour absorption photometer (TAP; λ=467 , 528, 652 nm) for filter-based light-absorption coefficients. One key finding is that the coefficients of light absorption, scattering and extinction derived from combing the measurements of two independent instruments agree with measurements from single instruments; the slopes of regression lines are equal within reported uncertainties (i.e. closure is observed). Despite closure for measured absorption coefficients, we caution that the estimated uncertainties for absorption coefficients, propagated for the differential method (DM; absorption = extinction minus scattering), can exceed 100 % for atmospherically relevant SSA values (>0.9). This increasing estimated uncertainty with increasing SSA yields AAE values that may be too uncertain for measurements in the range of atmospheric aerosol loadings. We recommend using the DM for measuring AAE values when the SSA < 0.9. EAE- and SAE-derived values achieved closure during this study within stated uncertainties for extinction coefficients greater than 15 Mm -1. SSA values for 450 and 630 nm wavelengths internally agreed with each other within 10 % uncertainty for all instrument combinations and sampled aerosol types, which fulfils the defined goals for measurement uncertainty of 10 % proposed by Laj et al. (2020) for GCOS (Global Climate Observing System) applications. [ABSTRACT FROM AUTHOR]

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nonvolatile particulate matter (nvPM) emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program was devised to understand reported variability in the ARP6320A sampling system nvPM measurements. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 campaigns devoted to: (1) assessing the response of three different black carbon mass analyzers to particles of different size, morphology, and chemical composition; (2) characterizing the particles generated by 6 different combustion sources according to morphology, effective density, and chemical composition; and (3) assessing any significant difference between black carbon as determined by the 3 mass analyzers and the total PM determined via other techniques. Results from VARIAnT 3 and 4 campaigns revealed agreement of about 20% between the Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PM SSA) monitor and the thermal-optical reference method for elemental carbon (EC) mass, independent of the calibration source used. For the LII-300, the measured mass concentrations in VARIAnT 3 fall within 18% and in VARIAnT 4 fall within 27% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT 3 and on an LGT-60 start cart in VARIAnT 4, respectively. It was also found that the three mass instrument types (MSS, CAPS PM SSA , and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion as a particle source (combustor or turbine engine). With respect to the particle size measurements, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Gravimetric measurements of the total aerosol mass produced by the various DFCAs differed from the reference EC, BC and integrated particle size distribution measured aerosol masses. The measurements of particle size distributions and single particle analysis performed using the miniSPLAT indicated the presence of larger particles (≳150 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and containing ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PM SSA instrument and higher OC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E−31 assumption that engine exit exhaust particles are mainly composed of black carbon. • PA and CAPS BC mass measurement methods have less variability than the LII BC method. • Gravimetric mass 30–40% greater than reference EC and 50–60% greater than BC masses. • Secondary particle mode >150 nm was observed dominated by non-volatile OC and containing ash. • Calibration of LII with a turbine combustion source more effective than other methods. [ABSTRACT FROM AUTHOR]

Aerosol intensive optical properties like the Ångström exponents for aerosol light extinction, scattering and absorption, or the single-scattering albedo are indicators for aerosol size distributions, chemical composition and radiative behaviour and contain also source information. The observation of these parameters requires the measurement of aerosol optical properties at multiple wavelengths which usually implies the use of several instruments. Our study aims to quantify the uncertainties of the determination of multiple-wavelengths intensive properties by an optical closure approach, using different test aerosols. In our laboratory closure study, we measured the full set of aerosol optical properties for a range of light-absorbing aerosols with different properties, mixed externally with ammonium sulphate to generate aerosols of controlled single-scattering albedo. The investigated aerosol types were: fresh combustion soot emitted by an inverted flame soot generator (SOOT, fractal aggregates), Aquadag (AQ, spherical shape), Cabot industrial soot (BC, compact clusters), and an acrylic paint (Magic Black, MB). One focus was on the validity of the Differential Method (DM: absorption = extinction minus scattering) for the determination of Ångström exponents for different particle loads and mixtures of light-absorbing aerosol with ammonium sulphate, in comparison to data obtained from single instruments. The instruments used in this study were two CAPS PMssa (Cavity Attenuated Phase Shift Single Scattering Albedo, ? = 450, 630 nm) for light extinction and scattering coefficients, one Integrating Nephelometer (? = 450, 550, 700 nm) for light scattering coefficient and one Tricolour Absorption Photometer (TAP, ? = 467, 528, 652 nm) for filter-based light absorption coefficient measurement. Our key finding is that the coefficients of light absorption sap, scattering ssp and extinction sep from the Differential Method agree with data from single reference instruments, and the slopes of regression lines equal unity within the precision error. We found, however, that the precision error for the DM exceeds 100% for sap values lower than 10-20 Mm-1 for atmospheric relevant single scattering albedo. This increasing uncertainty with decreasing sap yields an absorption Ångström exponent (AAE) that is too uncertain for measurements in the range of atmospheric aerosol loadings. We recommend using DM only for measuring AAE values for sap > 50 Mm-1. Ångström exponents for scattering and extinction are reliable for extinction coefficients from 20 up to 1000 Mm-1 and stay within 10% deviation from reference instruments, regardless of the chosen method. Single-scattering albedo (SSA) values for 450 nm and 630 nm wavelengths agree with values from the reference method ssp (NEPH)/sep (CAPS PMSSA) with less than 10% uncertainty for all instrument combinations and sampled aerosol types which fulfil the defined goals for measurement uncertainty of 10% proposed by Laj et al., 2020 for GCOS (Global Climate Observing System) applications. [ABSTRACT FROM AUTHOR]

We report the development and validation of a new humidified aerosol single-scattering albedometer to quantify the effects of water uptake on submicrometer particle optical properties. The instrument simultaneously measures in situ aerosol light extinction (σep) and scattering (σsp) using a cavity-attenuated phase shift-single scattering albedo particulate matter (PM) monitor (CAPS-PMSSA, Aerodyne Research, Inc., Billerica, MA, USA). It retrieves by difference aerosol light absorption (σap) and directly quantifies aerosol single-scattering albedo (SSA), the aerosol "brightness." We custom built a relative humidity (RH) control system using a water vapor-permeable membrane humidifier and coupled it to the CAPS-PMSSA to enable humidified aerosol observations. Our humidified instrument (H-CAPS-PMSSA) overcomes problems with noise caused by mirror purge-flow humidification, heating, and characterizing cell RH. Careful angular truncation corrections in scattering, particularly for larger particles, were combined with empirical observations. Results show that the optimal operational size to be Dp < 400 nm. The H-CAPS-PMSSA was evaluated with several pure single-component aerosols including ammonium sulfate ((NH4)2SO4), absorbing nigrosin, and levoglucosan, an organic biomass smoke tracer. The measured σep, σsp, and the derived optical hygroscopicity parameter (κ) for size-selected ammonium sulfate are in good agreement with literature values. For dry size-selected nigrosin in the 100 < Dp < 400 nm range, SSA values increased from ∼0.3 to 0.65 with increasing Dp. The enhancement in nigrosin σap at RH = 80% was a factor of 1.05–1.20 relative to dry conditions, with the larger particles showing greater enhancement. SSA increased with RH with the largest fractional enhancement measured for the smallest particles. For polydisperse levoglucosan, we measured an optical κ of 0.26 for both light extinction and scattering and negligible absorption. Our new instrument enables reliable observations of the effects of ambient humidity on mixed aerosol optical properties, particularly for light-absorbing aerosols whose climate forcing is uncertain due to measurement gaps. Copyright © 2021 American Association for Aerosol Research [ABSTRACT FROM AUTHOR]