Search

In recent years, Electric Vehicles (EVs) are contributing a major share in Thailand and benefit the environment. Most of the EV charging stations are sourced from solar energy as it becomes a carbon-free source of energy production. Secondly, Thailand is rich in solar irradiance, and higher irradiance leads to higher power production. On the other hand, in tropical conditions, solar Photovoltaic (PV) module temperature increases following the solar irradiance due to high ambient temperature, resulting negative impact on the efficiency and lifespan of photovoltaic (PV) modules. Further, to increase PV power production, in this study, different rates of cooling strategies are proposed. The study found that reducing the temperature by 5% to 25% resulted in increased average power outputs of 5947.94W, 6021.43W, 6094.92W, 6168.41W, and 6241W, respectively. Notably, 25% of the cooling rate achieved higher production. However, it is lower than the nominal power production. Following that, economic analysis and environmental impacts are analyzed for Thailand’s EV charging station using a different cooling rate of PV module. Overall, it is concluded that, depending on the economic viability of the EV charging station, cooling technology can be applied, and it will benefit the EV charging station both economically and environmentally. To further enhance the solar PV power production approach for EV charging stations in Thailand, it is imperative to prioritize future endeavors towards optimizing cooling technology, integrating energy storage, and implementing supportive policies.

This investigation explored the intensive characteristics of biomass and biochar from oil palm trunk (OPT) and oil palm fronds (OPF) for supporting the increasing demand of solid biofuels in Thailand. The characteristics of these samples were also compared to low grade sub-bituminous coal (LGSBC). The results indicate that converting OPT and OPF to biochar not only enhanced the fuel ratio and atomic ratios, but it also improved the energy content. The higher heating values (HHV) of OPT and OPF biochars were 26.92 and 28.05 MJ/kg. The fuel ratio, atomic ratio and HHV of biochars were better than those of LGSBC and biomass forms. Thermal decomposition and combustion characteristics of biomass and biochar from OPT and OPF were clearly different in N2and air atmospheres. The biomass and biochar from OPT and OPF had high contents of alkali elements, consequently their ashes had high concentrations of some oxides like SiO2 and K2O. Biomass and biochar ashes from OPT and OPF had low initial deformation temperature (IDT). The IDT of OPT biochar ash was the lowest (907 °C), while the IDT of ash from LGSBC was above 1500 °C. The slagging and fouling indexes of biochars were clearly different from the LGSBC and biomass forms. Therefore, biomass and biochar from OPT and OPF have potential for solid biofuel use, and they are promising for further upgrading and applications. The user needs to be concerned with ash related problems like ash fusion, slagging, and fouling during combustion of these solid biofuels.

The structural alteration of carbon nitride (CN) for photocatalytic CO2 reduction is a promising research topic in the environmental and energy sectors. This work discusses the fabrication of photocatalyst through a heterojunction architecture obtained from the molecular engineering of electron-rich organic monomer 2,6-pyridinedicarboxylic acid (PDA) with CN precursor (CN/PDAx). The successful integration of PDA in the structure of CN served as a charge inducting entity to enhance charge separation and photocatalytic CO2 reduction under visible light (λ = 420 nm). The DFT results indicated that the upshift in the HOMO level of CN after integration of PDA in its framework was the most lawful for the charge separation and for obtaining a high reduction potential. As-synthesized photocatalysts were demonstrated for various integral analysises and after evaluating the process of photocatalytic CO2 reduction under visible light region (λ = 420 nm). The optimized sample CN/PDA10 has the most excellent photocatalytic activity producing 85.4 μmol/h of CO and 21.3 μmol/h of H2, achieving a 7.5-fold enhanced catalytic efficiency as compared to pure CN. We hope that this work will attract more attention to synthesizing efficient photocatalysts for energy production and environmental remediation.

Semiconductor-based photocatalytic technology is regarded as an efficient pathway for resolving the energy scarcity across the globe. In this regard, graphitic carbon nitride (g-C3N4)-based materials could be alternatively employed in photochemical applications such as photovoltaic energy generation via CO2 photoreduction and water splitting, along with natural resource purification via organic/inorganic pollutant degradation. Indeed, this kind of assertion has been made by considering the intrinsic physicochemical properties of g-C3N4 nanomaterials, owing to their increased surface area, quantum yield, surface charge isolation, distribution, and ease of modification through material configuration or incorporation of preferred interfacial capabilities. This review article has been designed to provide the most up-to-date information regarding the further assessment of the important advancements in fabrication along with photochemical applications of various g-C3N4 nanomaterials, while specifically focusing on the scientific reason behind its success in each assessment. The discovery of interventions to alleviate such restrictions and boost photocatalytic performance has gained substantial interest. Following photo-excitation fundamentals, this work explains two distinct photoexcitation mechanisms, the carrier and charge transfer techniques, wherein the significant exciting state impact of g-C3N4 has still not been widely focused on in past studies. In this regards, we cautiously introduce the updated advances and associated functions of the alteration techniques, including morphological features, elemental dopants, deficiency engineering, and heterojunction implemented in photocatalytic performance, which are equated from the carrier and charge transport perceptions. The future perspectives in designing and properly tuning the highly active hierarchical or copolymer g-C3N4 nanoparticles in a photocatalytic system, which may improve the renewable energy cultivation and reduction efficiency are critically deciphered in detail and outlined thoroughly.

In Figure 2a [...]

The objective of this study was to investigate the production and properties of mixed pellets made from rubberwood (Hevea brasiliensis Muell. Arg) and refuse-derived fuel (RDF) waste with no added binder. Three different conditions of mixed pellets were developed to compare their chemical and physical properties to rubberwood pellets. The produced samples were subjected to both ultimate and proximate analyses. The contents of C, H, N, S, and Cl significantly increased with the increasing amount of refuse-derived fuel in the samples, resulting in reduction of the volatile matter. The mechanical durability of the pellet samples ranged between an average value of 98 and 99%. Mixed pellets containing 50% of rubberwood and 50% of refuse-derived fuel have improved heating values by 22.21% compared to rubberwood pellets. Moreover, mixed pellets having 50% of wood and 50% of refuse-derived fuel had the highest density and the highest energy compared to the other samples. Based on the findings of this study, it appears that the manufactured mixed pellets have the potential to be used as high-energy fuel.

This study assessed suitable smart grid areas for power generation and distribution from solar and small hydro energy resources in Western Uganda by employing the fuzzy analytic hierarchy process (AHP) based on geographic information system (GIS) data. This was performed based on the selected economic, environmental, and technical criteria by the authors guided by the experts’ judgements in the weighing process. The main criteria also included various sub-criteria. The sub-criteria of the economic criterion included distance from transmission lines, topography, and distance to roads. The environmental sub-criteria covered land use, sensitive areas, and protected areas. The technical sub-criteria were on distance from demand centers, available potential energy resources (solar and hydro), and climate (rainfall and sunshine). The weights of the main criteria and the sub-criteria were calculated by using the fuzzy AHP. These weights were then used in the GIS environment to determine both the potential for power generation from the solar energy resource and the smart grid suitable areas. According to the weight results, the economic criteria has the highest weight, followed by environmental and technical criteria. The validation of the experts’ judgements for each criterion by comparing the results from fuzzy AHP with AHP confirmed insignificant differences in weights for all criteria. The obtained suitable smart grid areas in Western Uganda have been classified into three parts, that is, the South, North, and Central. Therefore, this is a one-of-a-kind study that, in the authors’ view, will provide the initial insights to the government, policymakers, renewable energy practitioners, and researchers to investigate, map, and embrace decarbonization strategies for the electricity sector of Uganda.

Light-driven heterogeneous photocatalysis has gained great significance for generating solar fuel; the challenging charge separation process and sluggish surface catalytic reactions significantly restrict the progress of solar energy conversion using a semiconductor photocatalyst. Herein, we propose a novel and feasible strategy to incorporate dihydroxy benzene (DHB) as a conjugated monomer within the framework of urea containing CN (CNU-DHBx) to tune the electronic conductivity and charge separation due to the aromaticity of the benzene ring, which acts as an electron-donating species. Systematic characterizations such as SPV, PL, XPS, DRS, and TRPL demonstrated that the incorporation of the DHB monomer greatly enhanced the photocatalytic CO2 reduction of CN due to the enhanced charge separation and modulation of the ionic mobility. The significantly enhanced photocatalytic activity of CNU–DHB15.0 in comparison with parental CN was 85 µmol/h for CO and 19.92 µmol/h of the H2 source. It can be attributed to the electron–hole pair separation and enhance the optical adsorption due to the presence of DHB. Furthermore, this remarkable modification affected the chemical composition, bandgap, and surface area, encouraging the controlled detachment of light-produced photons and making it the ideal choice for CO2 photoreduction. Our research findings potentially offer a solution for tuning complex charge separation and catalytic reactions in photocatalysis that could practically lead to the generation of artificial photocatalysts for efficient solar energy into chemical energy conversion.