Search

• Unique 0.1 mm/pixel IR thermography diagnostic for plasma-wall interaction studies. • Improved accuracy and reliability on field of view positioning. • Operational on WEST tokamak since 2020. • Diagnostic is accurate to the monoblock. The Very High spatial Resolution (VHR) infrared thermography diagnostic developed by CEA-IRFM is installed in the WEST tokamak to measure surface temperature of the actively cooled W-monoblocks (MB) of the Plasma Facing Units (PFUs), which are similar to the International Thermonuclear Experimental Reactor (ITER) ones. It is a major diagnostic to investigate the behavior of PFU during experimentation thanks to its very high spatial resolution (0.1 mm / pixel), movable field of view (FoV) and the wide-range temperature measurement. In particular, it can study the evolution of monoblocks mounted in the tokamak, the influence of the shaping of these components submitted to high heat load and the behavior of the leading edges regarding the assembling tolerances between adjacent monoblocks. Finally, such diagnostic directly contributes to the specification assessment of the ITER divertor units. This diagnostic was operational during the 2019 WEST experimentation and its enhanced design for the 2020 WEST experimentation campaign. In order to monitor 30 × 12 mm monoblocks temperature, the VHR IR diagnostic is able to move its narrow FoV (64 × 51 mm) to specific targets on the observable divertor area (360 × 420 mm). Position and focus steering are achieved through motor-controlled mirrors and lenses operated by a dedicated Labview application on a remote unit. Mirror positioning occurs between pulses under normal WEST operation conditions, and can withstand thermal radiation and disruptions during pulses. Repeatability, hysteresis, mechanical components reliability are critical parameters to provide accurate positioning (<1 mm) of the FoV. The tuning and calibration of these actuators in accordance with WEST environment is crucial to guarantee the best position of the FoV and optical performances. This paper gives the FoV positioning implementation details and performance of the VHR in WEST. [ABSTRACT FROM AUTHOR]

A tangential infrared thermography system is installed in the WEST tokamak to observe the thermal scene of the first wall and the divertor components through a wide-angle tangential view. The goal is to provide and monitor the heat load deposition on the plasma facing components. About one-sixth of the chamber is observed, including sectors of the baffle, the lower and upper divertors, one inner bumper, vertical displacement event (VDE) protections, one ICRH antenna, and other parts of the wall. It is used for real time machine protection by monitoring temperature thresholds in delimited region of interest, and for analysis of normal or specific heat load events during operation such as VDE, ELM, disruption or runaways. This wide-angle view uses one aspherical and one on-axis plane mirrors, a sapphire window and three lenses for the objective of the camera. The optical line is optimized for two wavelengths 1.7 and 4 µm. The field of view is 60° on a 512×640 pixels Focal Plane Array. The endoscope is fully actively cooled. The thermal scene is complex to interpret given the fully metallic and radiative environment and the uncertainties on the emissivity which is angular-dependent and changes with the surface properties. This involves significant inaccuracy on the recovery of the real temperature. In this context, an interpretation by modeling approach is better suited, based on ray-tracing simulations taking into account the optical properties of materials. For instance, this allowed discriminating reflections patterns from real thermal events in the wide-angle view. A description of the wide-angle infrared diagnostic and its performances is presented as well as experimental measurements obtained in the WEST Tokamak. [ABSTRACT FROM AUTHOR]

WEST is a full W tokamak with an extensive set of diagnostics for heat load measurements especially in the lower divertor. It is composed by infrared thermography, thermal measurement with thermocouples and fibre Bragg grating embedded few mm below the surface and flush mounted Langmuir probes. A large database including different magnetic equilibrium and input power is investigated to compare the heat load pattern (location, amplitude of the peak and heat flux decay length) on the inner and outer strike point regions: from the first ohmic diverted plasma (obtained during the second experimental campaign C2 in 2018) up to the high power (8 MW total injected) and high energy (up to 90 MJ injected energy in lower single null configuration) experiments performed in the last experimental campaign (C4 in 2019). Concerning the peak location, a good agreement (<1 cm) is obtained between thermal inversions and flush-mounted LP measurements. The peak heat flux from the whole set of diagnostics is in good agreement and mainly in the ±20% range, while the heat flux decay length reported on the target shows significant discrepancy between diagnostics and location in the machine (±40% range). Despite such discrepancy, heat flux decay length at target is found to scale mainly with the magnetic flux expansion through the variation of the X-point height, as expected. The improved plasma performances achieved during C4 enabled to reach significant heat load in the divertor, up to 6 MW m−2 with 4 MW of additional heating power showing the capability to reach the ITER relevant heat load (10 MW m−2 steady state) with about 7 MW of additional power in L-mode discharge. The heat load distribution is clearly asymmetric with a 3/4 and 1/4 distribution on the outer and inner strike point region respectively for the parallel heat flux. [ABSTRACT FROM AUTHOR]

ITER (www.iter.org) will take advantage of tungsten (W) actively cooled plasma facing units (PFUs) in the lower divertor. These PFUs will receive a steady state plasma heat flux of 10 MW m−2 and up to 20 MW m−2 in slow transients, pushing these components to their limit. For machine protection reasons and for the study of the plasma wall interactions, temperature measurements are foreseen with mid wave infra-red (MWIR: 3–5 μm) thermography systems to cover most of the ITER chamber, including the divertor (tungsten material) and first wall (beryllium material) [1]. Absolute temperature measurements from 70 °C and the cooling temperature of the PFUs, up to 3500 °C (W melting temperature at 3422 °C), are considered. Those measurements require knowledge of the emissivity of the tungsten PFU surfaces as a function of the temperature and wavelength used for the IR monochrome thermography system. This paper summarizes the emissivity measurements performed on tungsten surfaces in high heat flux test beds and the WEST tokamak [2] and uses the experimental emissivity values to compute the expected uncertainties in ITER (ΔT/T) using monochrome and bicolor thermography techniques. The results show that the monochrome technique is not able to fulfill the ΔT/T < 10% requirement, while the bicolor technique is able to reduce the temperature uncertainty below 10%. Laboratory bicolor thermography measurements using a filter wheel (including six MWIR interference filters) have been successfully performed up to 830 °C with temperature uncertainty ΔT/T < 3%. In the WEST tokamak, the two dimensions emissivity map is varying by a factor of five within 27 cm along a PFU, from 0.13 to 0.65, showing that the monochrome IR thermography will have difficulties staying within the ITER requirements ΔT/T < 10% from 70 °C up to 3500 °C. [ABSTRACT FROM AUTHOR]

• We presented the WEST full tungsten actively cooled divertor, mentioning its relevance with the ITER one. • Main features including key elements related to the large-scale production, the reception tests, and the installation into the WEST tokamak are reported. • Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted. • Results related to the assessment of heat removal capability by IR-thermography and high heat flux test are discussed. The WEST (W - for tungsten - Environment in Steady-state Tokamak) platform aims to support the ITER tungsten divertor technology, manufacturing and long pulse operation. For this purpose, the Tore Supra tokamak has been deeply modified (mainly the installation of a lower and upper divertor coil structure), enabling a restart in 2016 and a first phase of operation (Phase I) until the end of 2020. Following this first phase, a limited number of actively cooled PFUs (Plasma Facing Units), based on ITER divertor technology, were industrially produced and implemented into the WEST vacuum vessel. The second phase of operation (Phase II) will be with a full actively cooled divertor. The first WEST experimental campaign with this new configuration (Phase II) started in 2022. This paper reports on the key elements related to the large-scale industrial production, the reception tests, and the installation of the ITER-like divertor components (including embedded instrumentation) into the WEST tokamak. Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted, mentioning its relevance with ITER divertor specifications. Results related to the assessment of heat removal capability by IR thermography examination and high heat flux test, as well as the He-leak tightness control are also discussed. [ABSTRACT FROM AUTHOR]

Plasma facing components temperature measurement is required to ensure safe high power for long pulse tokamak operation and for physics studies. During the WEST phase 1, a set of 20 thermocouples (TC) and 4 fibers Bragg grating (FBG) have been exposed to five experimental campaigns with 3889 plasmas for a total plasma duration of about 7h15 and 21.2 GJ of cumulated injected energy. This paper presents the performances in terms of response time and high temperature sustaining assess with high heat flux tests performed in the HADES facility. The response time of the TC remains at the same level as before their installation in the divertor. However, the FBG have shown clear increase of their response time depending on the location due to a degradation of the thermal contact of the graphite adhesive and the FBG or component. Finally, one regenerated FBG has been exposed to high temperature, showing that absolute temperature measurement is found reliable up to 1100 °C with the start of some spectrum degradations. Full erasure of the grating is obtained after 10 s at 1200 °C well above the stable temperature of 900 °C of the regenerated FBG. [ABSTRACT FROM AUTHOR]

The main objective of WEST is to study the behavior of the ITER-like divertor monobloc components, test their resistance and ageing under ITER relevant heat loads. For the upcoming phase 2 of WEST, the lower divertor is now fully equipped with the ITER-like actively cooled bulk tungsten Plasma Facing Units (PFU), designed to withstand 10MW/m² in steady state. This divertor is also equipped with an enlarged set of ThermoCouples (TCs x 16) and Fiber Bragg Gratings (FBGs) probes (x5) with 14 measurement spots each to evaluate the heat loading during the experiments. This paper presents the new TC and FBG diagnostics as well as the associated inverse method used to estimate the surface heat flux from the embedded temperature measurements in the divertor. The performance of each diagnostic will be evaluated with synthetic measurements generated with realistic heat flux intensity and distribution. The results of a parametrical analysis shows that each diagnostic is able to estimate the spatial distribution of the expected heat fluxes in WEST. [ABSTRACT FROM AUTHOR]

Plasma Facing Components (PFCs) temperature measurement is required to ensure safe high power for long pulse tokamak operation and for physics studies. A set of twenty thermocouples (TCs) and four optical fiber temperature sensing probes, each of them including eleven wavelength-multiplexed fiber Bragg gratings (FBGs) written with UV radiation, have been integrated and deployed in the WEST lower divertor. To avoid any thermal erasure occurring above 400 °C, the gratings have been regenerated using a high temperature annealing process. The FBG probes are embedded in tungsten-coated graphite components with no active cooling. The diagnostic was working correctly from the first plasma breakdown achieved in WEST (in 2017) until the first dismantling of the lower divertor three years later (2020). Collected data are sorted by temperature range to investigate the ageing of both PFCs and diagnostics. Measurements obtained with FBGs and TCs are consistent, no long-term drift is reported during the overall period of use. The maximum temperature reported by FBGs in the divertor is 830 °C obtained with 90 MJ of cumulated plasma energy in one pulse. A short but reversible collapse of the Bragg peak (from 5 down to 2 dB) has been observed under high temperature due to the strong temperature gradients measured along the fiber (about 20 °C/mm, for an FBG size of 3 mm). This feedback demonstrates that regenerated FBGs are suitable for long-term temperature monitoring in tokamak environment with high heat load, high temperature and gradient, strong magnetic field and vacuum constraint. [ABSTRACT FROM AUTHOR]

During the 2019 experimental campaign, the WEST tokamak was partially equipped with ITER-like plasma facing units (PFUs) made of discrete monoblocks (MBs) in one of the twelve lower divertor sectors. The magnetic field lines can enter the gaps between two MBs and strike their leading edges (LEs) with near normal incidence, leading to high localized heat flux, temperature and thermomechanical stress during both stead-state operation and transients. Exposed leading edges are a particular matter of concern because of potential crack formation, recrystallization or even melting of tungsten. During the 2019 experimental campaign in WEST, five of them were misaligned (vertical misalignment h = 0.30 ± 0.1 mm) with their poloidal leading edges exposed to the plasma heat flux. A medium wavelength IR filter (MWIR: 3.9 ± 0.1 μm) was installed in the very high resolution infrared system, featuring a submillimeter spatial resolution (∼0.1 mm/pixel). This system has a temperature detection threshold of T threshold, BB ≈ 250 °C. In this paper, thermal analysis will be presented with a specific focus on overheating of poloidal and toroidal edges using post-mortem measured emissivity maps. The study reveals an unexpected hot spot in the top LE corner of misaligned PFUs at the outer strike point (OSP). Photonic calculations were performed with different emissivity on top and lateral surfaces, in order to consider the complex reflectance characteristics in the toroidal gaps. During this experiment, the Larmor radius (0.35 mm) is comparable to the gap size. Thus, the helical trajectory of the particles may significantly affect the heat load distribution in the edges vicinity. Heat load simulations were performed with ion orbit modeling that consider the Larmor radius, to study its impact on the thermal distribution of the MB. The photonic simulations showed that it was possible to observe a false hot spot at the top LE corner, with both optical approximation (OA) and ion orbit (IO) modeling, due to reflections and different emissivity values. [ABSTRACT FROM AUTHOR]