Search

The effect of doping with holmium (Ho) and erbium (Er) rare-earth elements (REE) on the main parameters and characteristics of photocells based on p-GaSe/n-InSe heterostructures has been experimentally studied. Photo-electromotive force measurements were performed for undoped and rare-earth doped samples and obtained results comparatively analyzed. The light characteristic of the samples shows that significant improvement are observed in the rare-earth doped crystals. The possibility of targeted control, as well as increasing their reproducibility and stability by changing the content of the introduced impurity (NREE), is shown. The optimal situation is provided by alloying Er with NREE≈10−1 at.%. [ABSTRACT FROM AUTHOR]

The paper reveals the influence of Li, B and the composition of metal contacts on the processes of resistive switching in memristive structures M/NC/D/M. After field exposure in structures Cu/(Co50Fe50)x(LiNbO3)100–x/s-LiNbO3/Cu/sitall, Cu/(Co50Fe50)x(LiNbO3)100–x/d-LiNbO3/Cu/sitall and Cu/(Co40Fe40B20)x(SiO2)100–x/d LiNbO3/Cu/sitall at x < 13 was detected a residual voltage (up to 16 mV) due to the electromigration of Li ions, that leading to a "reversible" type of VAC hysteresis and instability of the time dependencies of induced resistive states. In the structures of Cu/(Co40Fe40B20)x(LiNbO3)100–x/s-LiNbO3/Cu/sitall, Cr/Cu/Cr/(Co40Fe40B20)x(LiNbO3)100–x/s-LiNbO3/Cr/Cu/Cr/sitall containing B, the residual voltage is reduced by formation of chemical compounds B with percolated Li atoms. When limiting the electromigration of Li ions, the main mechanism of resistive switching is the processes of electromigration of oxygen vacancies in the dielectric oxide layer. Suppression of residual voltage in the Cr/Cu/Cr/(Co50Fe50)x(LiNbO3)100–x/s-LiNbO3/Cr/Cu/Cr/sitall structure due to the introduction of a Cr buffer layer that does not dissolve Li leads to the absence of bipolar resistive switching in these structures. [ABSTRACT FROM AUTHOR]

The paper reveals the influence of Li, B and the composition of metal contacts on the processes of resistive switching in memristive structures M/NC/D/M. After field exposure in structures Cu/(Co50Fe50)x(LiNbO3)100–x/s-LiNbO3/Cu/sitall, Cu/(Co50Fe50)x(LiNbO3)100–x/d-LiNbO3/Cu/sitall and Cu/(Co40Fe40B20)x(SiO2)100–x/d LiNbO3/Cu/sitall at x < 13 was detected a residual voltage (up to 16 mV) due to the electromigration of Li ions, that leading to a "reversible" type of VAC hysteresis and instability of the time dependencies of induced resistive states. In the structures of Cu/(Co40Fe40B20)x(LiNbO3)100–x/s-LiNbO3/Cu/sitall, Cr/Cu/Cr/(Co40Fe40B20)x(LiNbO3)100–x/s-LiNbO3/Cr/Cu/Cr/sitall containing B, the residual voltage is reduced by formation of chemical compounds B with percolated Li atoms. When limiting the electromigration of Li ions, the main mechanism of resistive switching is the processes of electromigration of oxygen vacancies in the dielectric oxide layer. Suppression of residual voltage in the Cr/Cu/Cr/(Co50Fe50)x(LiNbO3)100–x/s-LiNbO3/Cr/Cu/Cr/sitall structure due to the introduction of a Cr buffer layer that does not dissolve Li leads to the absence of bipolar resistive switching in these structures. [ABSTRACT FROM AUTHOR]

To measure the spatial distribution of the magnetic field, both single Hall sensors and arrays of Hall sensors are used. In most cases, a one-dimensional ruler is sufficient. The finished device is called a measuring carriage. The rest of the article describes the first stage of its creation. This article consists in Hall sensor rejection, during which the sensors operate under extreme operating conditions (with increased electrical and thermal loads). During this so-called accelerated aging, the changes in the residual stress values, temperature coefficients, nonlinearity, and divergence of the sensitivity coefficient were monitored. This study can serve as a methodological guide in determining the selection criteria for Hall sensors for precision measuring systems. The need for aging sensors was shown to stabilize their long-term characteristics. In addition, the process of rejecting sensors according to the parameters of interest is described. [ABSTRACT FROM AUTHOR]

Recycling lithium-ion batteries provides sustainable raw materials. Crushing and separation are necessary for extracting metals, like lithium, from batteries. Crushing a battery carries a risk of fire or explosion. Fully discharging the battery is crucial for safe production. Discharging batteries in a salt solution is a simple and cost-effective large-scale process. However, it is important to note that there is a potential risk of corrosion and loss of battery elements when batteries are immersed in a salt solution. The purpose of this study is to investigate the effectiveness of two distinct methodologies at enhancing the voltage drop of a cylindrical battery when immersed in a salt solution while preventing corrosion. These techniques involve the application of iron and copper accelerators. A 20 wt.% salt water solution was chosen based on the research of several researchers. As the current flows through the metal parts, it encounters electrical resistance and forms an electric circuit with the electrolyte solution. This interaction converts electrical energy into various physical–electrical–electrochemical phenomena, leading to a decrease in battery voltage. Research revealed that the battery can be discharged up to 100% within 4 h without causing corrosion to its components. Another point to note is that if copper conductors are used, it is possible to decrease the battery voltage by around 90% within 8 h. The gap between the copper conductor and the battery had a direct impact on the battery's discharge rate. Reducing the distance significantly increased the discharge rate, as confirmed by experimental evidence. This discharge mechanism was thoroughly described in a schematic, and, to further explain the electrochemical reaction, the Pourbaix diagram was utilized for both the Fe-Na-Cl and Cu-Na-Cl systems. Moreover, our theoretical predictions were validated through a chemical and mineralogical analysis of the precipitates that formed in the solution. [ABSTRACT FROM AUTHOR]

Recycling lithium-ion batteries provides sustainable raw materials. Crushing and separation are necessary for extracting metals, like lithium, from batteries. Crushing a battery carries a risk of fire or explosion. Fully discharging the battery is crucial for safe production. Discharging batteries in a salt solution is a simple and cost-effective large-scale process. However, it is important to note that there is a potential risk of corrosion and loss of battery elements when batteries are immersed in a salt solution. The purpose of this study is to investigate the effectiveness of two distinct methodologies at enhancing the voltage drop of a cylindrical battery when immersed in a salt solution while preventing corrosion. These techniques involve the application of iron and copper accelerators. A 20 wt.% salt water solution was chosen based on the research of several researchers. As the current flows through the metal parts, it encounters electrical resistance and forms an electric circuit with the electrolyte solution. This interaction converts electrical energy into various physical–electrical–electrochemical phenomena, leading to a decrease in battery voltage. Research revealed that the battery can be discharged up to 100% within 4 h without causing corrosion to its components. Another point to note is that if copper conductors are used, it is possible to decrease the battery voltage by around 90% within 8 h. The gap between the copper conductor and the battery had a direct impact on the battery’s discharge rate. Reducing the distance significantly increased the discharge rate, as confirmed by experimental evidence. This discharge mechanism was thoroughly described in a schematic, and, to further explain the electrochemical reaction, the Pourbaix diagram was utilized for both the Fe-Na-Cl and Cu-Na-Cl systems. Moreover, our theoretical predictions were validated through a chemical and mineralogical analysis of the precipitates that formed in the solution.

With the widespread application of permanent magnet synchronous motor (PMSM) drives, the demand for safety and reliability has increased. Inverter open-circuit fault is a frequent and severe failure that requires reliable detection and remedial measures. This paper proposes an open-circuit fault diagnosis technique based on voltage residual analysis that does not require additional voltage sensors. The proposed technique analyzes the characteristics of the reference voltage and the actual output voltage under both healthy and fault conditions. To achieve fast and reliable fault detection, it uses the DC component and second harmonic component in the residual voltage between estimated voltage and controller reference voltage. Once an open-circuit fault is detected, the polarity of the DC component is capable of identifying the fault location. The effectiveness and robustness of the proposed technique are verified through simulations and testing on a triple redundant PMSM under various load and speed conditions. [ABSTRACT FROM AUTHOR]

Users expect reliable operation of the surge arrester during overvoltages, which may originate from a switching process or a lightning discharge. The necessary conditions to guarantee these expectations are: appropriate construction of the surge arrester, its production being maintained in accordance with technical standards, and a positive results of the type test (as well routine and acceptance tests). The recipient, especially when purchasing large quantities of the product, can check the final quality of the product through selective testing of samples from the market in order to find the best supplier. This manuscript specifies the basic parameters of low-voltage (LV) surge arresters of four manufacturers. Basic electrical parameters, i.e. leakage current and varistor voltage ( $\text{U}_{\mathrm {1mA}}$ ) before and after the nominal discharge current ( $\text{I}_{\mathrm {n}}$ ) of $8~\mu \text{s}$ /20 $\mu \text{s}$ , were determined for 10 randomly selected surge arresters of each manufacturer. Moreover one sample of each varistor batches was aged by fifty 8 $\mu \text{s}$ /20 $\mu \text{s}$ current impulses with $\text{I}_{\mathrm {n}}$ . The obtained results of structural analysis indicate that the crystal structure of the varistor materials changes after ageing process, affecting its electrical properties. The proposed research methodology can be employed as a basis for forecasting the stability of the arrester parameters under operating conditions.

Before the disposal of lithium–cobalt batteries and lithium–manganese batteries, they must first be discharged to a voltage no greater than 0.5 V. Above 0.5 V, the batteries will catch alight and explode on being opened. Various methods of battery discharge are considered: self-discharge using a flashlight; and battery immersion in NaCl solutions of concentration 5, 10, or 15 wt %. Discharge in salt solution is associated with electrolysis. This process may be theoretically described by means of the basic principles of chloride electrolysis. The effective concentration of the salt solution in battery discharge is found to be 10 wt %. Graphs showing the discharge of LiMn2O4 and LiCoO2 batteries over time are plotted, for a motionless medium. The discharge time is decreased in reactors where mechanical mixers ensure transient or turbulent motion of the liquid (assessed on the basis of the Reynolds number ReM). By atomic-emission spectrometry, the components formed in the residue after battery discharge are determined. On the basis of the results, mixer parameters for preliminary discharge of lithium–cobalt and lithium–manganese batteries are recommended, such that subsequent battery disposal in industrial conditions poses no environmental risks. [ABSTRACT FROM AUTHOR]

With the widespread application of permanent magnet synchronous motor (PMSM) drives, the demand for safety and reliability has increased. Inverter open-circuit fault is a frequent and severe failure that requires reliable detection and remedial measures. This paper proposes an open-circuit fault diagnosis technique based on voltage residual analysis that does not require additional voltage sensors. The proposed technique analyzes the characteristics of the reference voltage and the actual output voltage under both healthy and fault conditions. To achieve fast and reliable fault detection, it uses the DC component and second harmonic component in the residual voltage between estimated voltage and controller reference voltage. Once an open-circuit fault is detected, the polarity of the DC component is capable of identifying the fault location. The effectiveness and robustness of the proposed technique are verified through simulations and testing on a triple redundant PMSM under various load and speed conditions.

In order to study the strong electromagnetic pulse effect of critically vulnerable equipment in power systems and evaluate the survivability under high-altitude electromagnetic pulses, it is necessary to study the characteristics of the transient response of metal oxide arresters to the high-altitude electromagnetic pulse by experiment. In this paper, an experimental platform for high-altitude electromagnetic pulse conduction current injection for a typical 10 kV metal oxide arrester was set up, and the key parameters such as peak value of overshoot voltage, peak value of residual voltage, action voltage and response time were obtained by the experiment. The results show that: the action voltage of this type of metal oxide arrester is 3.53 times higher than that of its rated voltage; the peak value of overshoot voltage is 2.19 times that of the peak value of residual voltage under lightning impulse current; the peak value of residual voltage is 1.57 times that under lightning impulse; and the response time varies little with the electromagnetic pulse conduction current amplitude, averaging 46.86 nanoseconds under a high-altitude electromagnetic pulse conduction environment. [ABSTRACT FROM AUTHOR]

In order to study the strong electromagnetic pulse effect of critically vulnerable equipment in power systems and evaluate the survivability under high-altitude electromagnetic pulses, it is necessary to study the characteristics of the transient response of metal oxide arresters to the high-altitude electromagnetic pulse by experiment. In this paper, an experimental platform for high-altitude electromagnetic pulse conduction current injection for a typical 10 kV metal oxide arrester was set up, and the key parameters such as peak value of overshoot voltage, peak value of residual voltage, action voltage and response time were obtained by the experiment. The results show that: the action voltage of this type of metal oxide arrester is 3.53 times higher than that of its rated voltage; the peak value of overshoot voltage is 2.19 times that of the peak value of residual voltage under lightning impulse current; the peak value of residual voltage is 1.57 times that under lightning impulse; and the response time varies little with the electromagnetic pulse conduction current amplitude, averaging 46.86 nanoseconds under a high-altitude electromagnetic pulse conduction environment.

• The fuzziness of residual voltage, the correlation of duration and the chaos of occurrence time are proposed. • Three prediction models to predict voltage sag characteristics is proposed. • Fuzzy membership function is used to describe the voltage sag fluctuation of nodes under time-varying conditions. • A evidence theory synthesis formula is proposed to enhance the predictability of duration. • The phase space reconstruction is used to describe the multi-dimensional factors affecting the occurrence of voltage sag. An effective method of assisting utilities and users to avoid the risk of voltage sags is the accurate prediction of voltage sags. This study analyzes the predictability and proposes the prediction models for three characteristics of voltage sags based on measured data. First, this study defines the time series of voltage sag and analyzes the predictability of the residual voltage, duration, and time of occurrence. Second, this study proposes a fuzzy logic prediction model of the residual voltage to address the fuzziness of the residual voltage. Third, this study proposes an evidence theory prediction model of the duration according to the correlation between the residual voltage and duration. Further, this study proposes a chaotic signal prediction model of the occurrence time by reconstructing the phase space of the occurrence time. Finally, the measured voltage sag data from 10 sites are used to analyze and validate the proposed prediction models. [ABSTRACT FROM AUTHOR]

• Electromagnetic transient model for varistor-based surge protective devices. • Resistive, inductive, and capacitive behavior of varistor-based SPDs. • Residual voltage of SPDs depends significantly on their base configuration. • Excellent simulation results for a wide range of very fast-front impulse currents. • The model can be used for insulation coordination studies and dimensioning of SPDs. This work provides a simplified transient model for low-voltage DIN rail surge protective devices (SPDs), accounting for their resistive, inductive, and capacitive behavior. The time-domain modeling approach is based on impulse current and sinusoidal voltage experiments. The lumped-circuit model is implemented in the ATP-EMTP environment and yields results in satisfactory agreement with the experimentally derived residual voltage and energy absorption of commercially available DIN rail SPDs for single- and three-phase installations. The proposed model can be used for evaluating the protection level and maximum residual voltage of SPDs under standard and non-standard surge currents and can be an effective tool employed in insulation coordination studies of power systems. [ABSTRACT FROM AUTHOR]

• The single-phase reclosing technique should not be used in half-wavelength transmission systems. • The residual voltage of half wavelength transmission system can be used to determine the existence of faults. • The frequency difference of residual voltage can be used to determine the existence of faults. • We propose a complete and feasible three-phase adaptive reclosure scheme for half wavelength transmission system. UHV AC transmission lines use adaptive reclosure technology not only to avoid reclosing in the permanent faults, but also effectively prevent the emergence of reclosing overvoltage, adaptive reclosure is of great significance, and its technical principle is based on the study and judgment of the existence of the fault. The reactive power of half-wavelength transmission lines along the line was self-balanced, no shunt reactor equipment, there is no "beat frequency" phenomenon, and very little information is available after the three-phase trip. In this paper, we analyze the fault traveling wave's frequency characteristics and identify the fault's characteristics based on the residual voltage frequency difference of the line after the three-phase trip. After the disappearance of the line fault, the stable frequency difference obtained by CVT reflects the entire length of the line, which is not affected by the system boundary conditions and can complete the reliable identification of the disappearance of the line fault. The two-terminal criterion is given for the short-line dead zone problem, and then a three-phase adaptive reclosure scheme for half-wavelength transmission lines based on the frequency difference to identify fault disappearance is proposed. Extensive RTDS digital-analog hybrid tests show that the method is correct and robust. [ABSTRACT FROM AUTHOR]

• Complete VFTO(s) generation and measurement system based on (MPC) and (TLT) technologies. • Five commercial ZnO varistors of the same reference were used in the characterization. • The influence of the applied overvoltage front time on the capacitive effect of the varistor is confirmed. To study the behavior of low voltage ZnO varistors against Very Fast Transient Overvoltage (VFTO), the authors have developed a complete VFTO(s) generation and measurement system based on magnetic pulse compression (MPC) and Transmission Line Transformer (TLT). This system has an output voltage of 24 kV, rise time of 32 ns, and a bandwidth of 10 MHz. The measurement system comprises a damped resistive voltage divider with an impedance of 1000 MΩ and a maximum bandwidth of 10 MHz. The experiment was performed with five commercial zinc oxide varistors with a nominal voltage of 150 V, each one was subjected to VFTO-type voltage pulses and, by Analysis of Variance (ANOVA), a single varistor was selected to perform the case study. This work presents an experimental methodology to observe the response of low voltage ZnO varistors against VFTO. This response is the delay of the residual voltage to the applied discharge current and indicates the poor performance of these devices against VFTOs. Our methodological proposal consists of a series of laboratory tests that will allow manufacturers and consumers to take corrective measures in case of malfunction, damage of the varistor material, or permanent degradation of the device. [ABSTRACT FROM AUTHOR]

• The electrostatic field and voltage distribution analyses are carried out on 245 kV surge arrester by considering various shield designs using numerical techniques. • Design of grading shield and development of GISA is verified by performing dielectric duties as per IEC 62,271–203. • The lightning and switching impulse discharge current tests were conducted on the developed 245 kV GISA assembly and residual voltages were recorded. • V-I characteristics of GISA is established by measuring residual voltages for the entire current range. The voltage distribution across gas insulated surge arrester (GISA) is highly non-uniform as compared to conventional porcelain-clad surge arresters. The aim of the present paper is to optimize design of grading shield in such a way that the non-uniformity voltage factor across GISA must be less than ±10%. To achieve this order of non-uniformity factors, special grading shields like window based cylindrical and conical shields are proposed. In the present paper, 245 kV GISA model has been considered to analyze voltage distribution across the metal-oxide (MO) blocks. The electrostatic field and voltage distribution analyses are carried out on surge arrester by considering various shield configurations using numerical techniques. Further, design of shield and development is verified by performing dielectric duties on GISA assembly without MO blocks as per IEC 62,271–203. The lightning and switching impulse discharge current tests were carried out on the developed 245 kV GISA residual voltages were recorded. These voltage levels for above discharge currents are found to be in the order of 2.8 – 3.2 p. u. and are at acceptable levels as per IEC 60,099–4. Finally, protection level or V-I characteristics of GISA is established by measuring residual voltages for the entire current range. [ABSTRACT FROM AUTHOR]