Search

Thermophotovoltaics, devices that convert thermal infrared photons to electricity, offer a key pathway for a variety of critical renewable energy technologies including thermal energy storage, waste heat recovery, and direct solar-thermal power generation. However, conventional far-field devices struggle to generate reasonable powers at lower temperatures. Near-field thermophotovoltaics provide a pathway to substantially higher powers by leveraging photon tunneling effects. Here we present a large area near-field thermophotovoltaic device, created with an epitaxial co-fabrication approach, that consists of a self-supported 0.28 cm2 emitter-cell pair with a 150 nm gap. The device generates 1.22 mW at 460 C, a twenty-five-fold increase over the same cell measured in a far-field configuration. Furthermore, the near-field device demonstrates short circuit current densities greater than the far-field photocurrent limit at all the temperatures tested, confirming the role of photon tunneling effects in the performance enhancement. Modeling suggests several practical directions for cell improvements and further increases in power density. These results highlight the promise of near-field thermophotovoltaics, especially for low temperature applications.

We present inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub-0.60 eV bandgaps grown on InP and GaAs substrates. The compositionally graded buffers in these devices have threading dislocation densities of 1.3x10^6 cm^-2 and 8.9x10^6 cm^-2 on InP and GaAs, respectively. The devices generate open-circuit voltages of 0.386 V and 0.383 V, respectively, at a current density of ~10 A/cm^2, yielding bandgap-voltage offsets of 0.20 and 0.21 V. We measured their broadband reflectance and used it to estimate thermophotovoltaic efficiency. The InP-based cell is estimated to yield 1.09 W/cm^2 at 1100 degrees C vs. 0.92 W/cm^2 for the GaAs-based cell, with efficiencies of 16.8 vs. 9.2%. The efficiencies of both devices are limited by sub-bandgap absorption, with power weighted sub-bandgap reflectances of 81% and 58%, respectively, which we assess largely occurs in the graded buffers. We estimate that the thermophotovoltaic efficiencies would peak at ~1100 degrees C at 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application to laser power conversion in the 2.0-2.3 micron atmospheric window. We estimate peak LPC efficiencies of 36.8% and 32.5% under 2.0 micron irradiances of 1.86 W/cm^2 and 2.81 W/cm^2, respectively., Comment: 14 pages, 6 figures

Thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste heat recovery. Here, we report the design, fabrication, and testing of large area (0.8 cm$^2$), scalable, single junction 0.74-eV GaInAs thermophotovoltaic devices reaching an efficiency of 38.8$\pm$2.0% and an electrical power density of 3.78 W/cm$^2$ at an emitter temperature of 1850{\deg}C. Reaching such a high emitter temperature and power density without sacrificing efficiency is a direct result of combining good spectral management with a highly optimized cell architecture, excellent material quality, and very low series resistance. Importantly, fabrication of 12 high-performing devices on a two-inch wafer is shown to be repeatable, and the cell design can be readily transferred to commercial epitaxy on even larger wafers. Further improvements in efficiency can be obtained by using a multijunction architecture, and early results for a two-junction 0.84-eV GaInPAs / 0.74-eV GaInAs device illustrate this promise., Comment: 27 pages, 15 figures

Near-field radiative heat transfer (NFRHT) between irregularly shaped dielectric particles made of SiO2 and morphology characterized by Gaussian random spheres is studied. Particles are modeled using the discrete system Green's function (DSGF) approach, which is a volume integral numerical method based on fluctuational electrodynamics. This method is applicable to finite, three-dimensional objects, and all system interactions are defined independent of thermal excitation by a generalized system Green's function. The DSGF method is deemed suitable to model NFRHT between irregularly shaped particles after verification against the analytical solution for chains of two and three SiO2 spheres. The NFRHT results reveal that geometric irregularity in particles leads to a reduction of the total conductance from that of comparable perfect spheres at vacuum separation distances smaller than the particle size, a regime in which NFRHT is a surface phenomenon. At vacuum separation distances larger than the particle size, NFRHT becomes a volumetric process, and the total conductance between irregularly shaped particles converges to that of comparable perfect spheres. Spectral analysis reveals, however, that particle irregularity leads to damping and broadening of resonances at all separation distances, thereby highlighting the importance of the DSGF method for spectral engineering in the near field. The reduced spectral coherence when particle size is larger than the vacuum separation distance is attributed to coupling of surface phonon-polaritons within the randomly generated, distorted particle features. For particle size smaller than the vacuum separation distance, resonance broadening and damping is linked with the multiple localized surface phonon modes supported by the composite spherical harmonic morphologies of the Gaussian random spheres., Comment: 59 pages, 9 figures, 6 supplementary figures

An ideal solar thermal absorber has a sharp transition between high and low absorptance at the wavelength where the blackbody emissive power begins to exceed the solar irradiance. However, most real selective absorbers have a fairly broad transition, leading to both solar absorption and thermal emission losses. Here, we model, fabricate, and characterize a highly selective semiconductor-dielectric-metal (Ga0.46In0.54As - MgF2 - Ag) solar absorber with an extremely sharp transition from high to low absorptance. The thin semiconductor serves as a selective filter, absorbing photons with wavelengths shorter than the bandgap and transmitting those with longer wavelengths. The highly reflective dielectric-metal rear mirror allows the structure to have very low emittance for longer wavelengths. These characteristics provide the absorber with a measured solar absorptance >91% below the bandgap wavelength and infrared emittance <5% at 100 C above the bandgap wavelength. This transition wavelength can be tuned by modifying the semiconductor composition, and modeling indicates that the absorber's optical properties should be stable at high temperatures, making the structure a good candidate for unconcentrated to highly concentrated solar thermal energy conversion., Comment: 16 pages, 6 figures