Search

Constructing highly efficient catalysts for the degradation of organic pollutants driven by solar light in aquatic environments is a promising and green strategy. In this study, a novel hexagonal sheet-like Pt/SnS2 heterojunction photocatalyst is successfully designed and fabricated using a hydrothermal method and photodeposition process for photocatalytic tetracycline (TC) degradation. The optimal Pt/SnS2 hybrid behaves with excellent photocatalytic performance, with a degradation efficiency of 91.27% after 120 min, a reaction rate constant of 0.0187 min−1, and durability, which can be attributed to (i) the formation of a metal/semiconductor interface field caused by loading Pt nanoparticles (NPs) on the surface of SnS2, facilitating the separation of photo-induced charge carriers; (ii) the local surface plasmon resonance (LSPR) effect of Pt NPs, extending the light absorption range; and (iii) the sheet-like structure of SnS2, which can shorten the transmission distance of charge carriers, thereby allowing more electrons (e−) and holes (h+) to transfer to the surface of the catalyst. This work provides new insights with the utilization of sheet-like structured materials for highly active photocatalytic TC degradation in wastewater treatment and environmental remediation. [ABSTRACT FROM AUTHOR]

Thermoplastic nonwoven composites were produced with the air‐laying and foam‐forming processes from cellulosic and plastic fibers. The two raw material combinations were (1) PP/PE (fiber length 3 mm), PP/PE (12 mm), fluff pulp fibers (2 mm) and (2) PP/PE (3 mm), fluff pulp fibers, viscose (10 mm). After forming, the fibrous sheets (400 gsm) were bonded with heat pressing (145°C). The effect of the carrier medium, air or aqueous foam, on the tensile and impact properties and sheet structure was explored. The air‐laids differed from the foam‐laids by sheet anisotropy, density, and the lack of an additional bonding regime between wood fibers due to the dry forming process. The PP/PE bonding fibers gave the air‐laids a good capacity to elongate compared to the foam‐laids. The advantage was lost when nonbonding viscose was added. The impact strength was dependent on the PP/PE dosage and the sheet density, rather than the moisture‐induced bonding between wood fibers. The changing long/short fiber ratios caused gradual shifts in sheet properties, usually a reduction in a mechanical property as the share of short fiber increased in the mix. Economic analysis revealed that increasing fluff content can reduce raw material costs, providing a possibility for cost optimization in total production costs. [ABSTRACT FROM AUTHOR]

Ethyl 2-[(2-oxo-2H-chromen-6-yl)oxy]acetate, C13H12O5, a member of the pharmacologically important class of coumarins, crystallizes in the monoclinic C2/c space group in the form of sheets, within which molecules are related by inversion centers and 21 axes. Multiple C—H...O weak hydrogen-bonding interactions reinforce this pattern. The planes of these sheets are oriented in the approximate direction of the ac face diagonal. Intersheet interactions are a combination of coumarin system π–π stacking and additional C—H...O weak hydrogen bonds between ethyl acetoxy groups.

Ethyl 2-[(2-oxo-2H-chromen-6-yl)­oxy]acetate, C13H12O5, a member of the pharmacologically important class of coumarins, crystallizes in the monoclinic C2/c space group in the form of sheets, within which mol­ecules are related by inversion centers and 21 axes. Multiple C—H⋯O weak hydrogen-bonding inter­actions reinforce this pattern. The planes of these sheets are oriented in the approximate direction of the ac face diagonal. Inter­sheet inter­actions are a combination of coumarin system π–π stacking and additional C—H⋯O weak hydrogen bonds between ethyl acet­oxy groups. [ABSTRACT FROM AUTHOR]

Constructing highly efficient catalysts for the degradation of organic pollutants driven by solar light in aquatic environments is a promising and green strategy. In this study, a novel hexagonal sheet-like Pt/SnS2 heterojunction photocatalyst is successfully designed and fabricated using a hydrothermal method and photodeposition process for photocatalytic tetracycline (TC) degradation. The optimal Pt/SnS2 hybrid behaves with excellent photocatalytic performance, with a degradation efficiency of 91.27% after 120 min, a reaction rate constant of 0.0187 min−1, and durability, which can be attributed to (i) the formation of a metal/semiconductor interface field caused by loading Pt nanoparticles (NPs) on the surface of SnS2, facilitating the separation of photo-induced charge carriers; (ii) the local surface plasmon resonance (LSPR) effect of Pt NPs, extending the light absorption range; and (iii) the sheet-like structure of SnS2, which can shorten the transmission distance of charge carriers, thereby allowing more electrons (e−) and holes (h+) to transfer to the surface of the catalyst. This work provides new insights with the utilization of sheet-like structured materials for highly active photocatalytic TC degradation in wastewater treatment and environmental remediation.

The photoreduction of CO2 to other products containing carbon through simulated photosynthesis is a promising area of research. However, given the complexity of the CO2 photocatalytic reduction reaction, it is crucial to adjust the structure of the photocatalysts. The focus of this study was on creating NaOH-modified Bi2WO6 nanosheet photocatalysts via a one-step hydrothermal route and using them to convert CO2 into CO through photocatalytic reduction under the condition of not using an electron sacrifice agent. The results of characterizations and activity data showed that adding an appropriate amount of NaOH significantly improved the photoreduction activity of CO2, as seen in the BWO-2 catalyst. The efficiency of photocatalysts could be improved by tuning the band structure through the addition of an appropriate amount of alkali. This adjustment improves the separation of photogenerated carriers and controls the concentration of oxygen vacancy to reduce recombination. As a result, the photocurrent activity is highly enhanced, leading to better reduction performance compared to unmodified photocatalysts. In experiments, the CO yield of the modified photocatalyst BWO-2 remained above 90 μmol/g after four trials, indicating its effectiveness in reducing CO2. This study offers insights into the regulation of band structure in bismuth-based photocatalysts for efficient CO2 reduction. [ABSTRACT FROM AUTHOR]

Introduction: Oil-based emulsion solution is a common pesticide formulation in agricultural spraying, and its spray characteristics are different from that of water spraying. The well understanding of its spray characteristics is the theoretical basis to improve the pesticide spraying technology. The objective of the present study is to deepen the understanding of the spray characteristics of oil-based emulsion. Method: In this paper, the spatial distribution characteristics of spray droplets of oil-based emulsion were captured visually using the high-speed photomicrography. On the basis of image processing method, the droplet size and distribution density of spray droplets at different spatial locations were analyzed quantitatively. The effects of nozzle configuration and emulsion concentration on spray structures and droplet spatial distribution were discussed. Results: Oil-based emulsion produced a special perforation atomization mechanism compared with water spray, which led to the increase of spray droplet size and distribution density. Nozzle configuration had a significant effect on oil-based emulsion spray, with the nozzle changed from ST110-01 to ST110-03 and ST110-05; the sheet lengths increased to 18 and 28 mm, respectively, whereas the volumetric median diameters increased to 51.19% and 76.00%, respectively. With emulsion concentration increased from 0.02% to 0.1% and 0.5%, the volumetric median diameters increased to 5.17% and 14.56%, respectively. Discussion: The spray droplet size of oil-based emulsion spray can be scaled by the equivalent diameter of discharge orifice of nozzles. The products of volumetric median diameters and corresponding surface tensions were nearly constant for the oil-based emulsion spray of different emulsion concentrations. It is expected that this research could provide theoretical support for improving the spraying technology of oil-based emulsion and increasing the utilization of pesticide. [ABSTRACT FROM AUTHOR]

Oil-based emulsion is a common herbicide formulation in agricultural spray, and its atomization mechanism is different from that of water spray. In this paper, a theoretical model based on the characteristics of spray sheets was proposed to predict the spray droplet size for oil-based emulsion spray. An image processing method was used to measure droplet size distributions for different spray pressures and nozzle configurations, and the measured results were used to validate the theoretical model. The results show that oil-based emulsion spray is characterized by the web structure constituted by perforations. The liquid originally occupied by spray sheets eventually gathers in these web structures. The proposed theoretical model is based on the size of the nozzle exit, the angle of spray sheets, and the perforation number in the web structure, which are relatively easy to obtain. The theoretical droplet size is in inverse proportion to the square root of the perforation number in the web structure while in proportion to the square root of the area of the nozzle exit. The captured images of spray sheets and the measured droplet size distribution show consistency with the theoretical prediction. The difference between theoretical results and measured volumetric median diameter is less than 10% for different spray pressures and nozzles. [ABSTRACT FROM AUTHOR]

Pulp fiber airlaid nonwovens were bonded with three binder formulations in a spray and foam process. The binders were: a commercial acrylic dispersion binder, a commercial bio-containing acrylic binder; and a citric acid-carboxymethyl cellulose mixture (CACMC) (1:1 by-weight). The binder solutions were applied at same concentrations onto A4-size airlaid sheets (80 gsm) under a vacuum with 2-sided spraying and 1-sided foam coating. The sheet structure, dry and wet tensile properties, and total absorption capacity were compared. The foam application densified and bulk bonded the sheets, whereas the spray application induced surface bonding. These factors fundamentally influenced the measured sheet properties. The dry tensile strength was linearly correlated with the relatively low binder dosages. The CACMC binder exposed the differences in the binder application processes well, and lead to strong sheets with small elongation and highly application method-dependent absorption capacity compared to acrylic binders. [ABSTRACT FROM AUTHOR]

Introduction: Oil-based emulsion solution is a common pesticide formulation in agricultural spraying, and its spray characteristics are different from that of water spraying. The well understanding of its spray characteristics is the theoretical basis to improve the pesticide spraying technology. The objective of the present study is to deepen the understanding of the spray characteristics of oil-based emulsion., Method: In this paper, the spatial distribution characteristics of spray droplets of oil-based emulsion were captured visually using the high-speed photomicrography. On the basis of image processing method, the droplet size and distribution density of spray droplets at different spatial locations were analyzed quantitatively. The effects of nozzle configuration and emulsion concentration on spray structures and droplet spatial distribution were discussed., Results: Oil-based emulsion produced a special perforation atomization mechanism compared with water spray, which led to the increase of spray droplet size and distribution density. Nozzle configuration had a significant effect on oil-based emulsion spray, with the nozzle changed from ST110-01 to ST110-03 and ST110-05; the sheet lengths increased to 18 and 28 mm, respectively, whereas the volumetric median diameters increased to 51.19% and 76.00%, respectively. With emulsion concentration increased from 0.02% to 0.1% and 0.5%, the volumetric median diameters increased to 5.17% and 14.56%, respectively., Discussion: The spray droplet size of oil-based emulsion spray can be scaled by the equivalent diameter of discharge orifice of nozzles. The products of volumetric median diameters and corresponding surface tensions were nearly constant for the oil-based emulsion spray of different emulsion concentrations. It is expected that this research could provide theoretical support for improving the spraying technology of oil-based emulsion and increasing the utilization of pesticide., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Gong, Chen, Cui, Wang, Zhang, Zhou and Liu.)

Oil-based emulsion is a common herbicide formulation in agricultural spray, and its atomization mechanism is different from that of water spray. In this paper, a theoretical model based on the characteristics of spray sheets was proposed to predict the spray droplet size for oil-based emulsion spray. An image processing method was used to measure droplet size distributions for different spray pressures and nozzle configurations, and the measured results were used to validate the theoretical model. The results show that oil-based emulsion spray is characterized by the web structure constituted by perforations. The liquid originally occupied by spray sheets eventually gathers in these web structures. The proposed theoretical model is based on the size of the nozzle exit, the angle of spray sheets, and the perforation number in the web structure, which are relatively easy to obtain. The theoretical droplet size is in inverse proportion to the square root of the perforation number in the web structure while in proportion to the square root of the area of the nozzle exit. The captured images of spray sheets and the measured droplet size distribution show consistency with the theoretical prediction. The difference between theoretical results and measured volumetric median diameter is less than 10% for different spray pressures and nozzles., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Gong, Chen and Kang.)