Search

Pore-throat size is a very crucial factor controlling the reservoir quality and oiliness of tight sandstones, which primarily affects rock-properties such as permeability and drainage capillary pressure. However, the wide range of size makes it difficult to understand their distribution characteristics as well as the specific controls on reservoir quality and oiliness. In order to better understand about pore-throat size distribution, petrographic, scanning electron microscopy (SEM), pressure-controlled mercury injection (PMI), rate-controlled mercury injection (RMI), quantitative grain fluorescence (QGF) and environmental scanning electron microscopy (ESEM) investigations under laboratory pressure conditions were performed on a suite of tight reservoir from the fourth member of the Lower Cretaceous Quantou Formation (K 1 q 4 ) in the southern Songliao Basin, China. The sandstones in this study showed different types of pore structures: intergranular pores, dissolution pores, pores within clay aggregates and even some pores related to micro fractures. The pore-throat sizes vary from nano- to micro-scale. The PMI technique views the pore-throat size ranging from 0.001 μm to 63 μm and revealed that the pore-throats with radius larger than 1.0 μm are rare and the pore-throat size distribution curves show evident fluctuations. RMI measurements indicated that the pore size distribution characteristics of the samples with different porosity and permeability values look similar. The throat size and pore throat radius ratio distribution curves had however significant differences. The overall pore-throat size distribution of the K 1 q 4 tight sandstones was obtained with the combination of the PMI and RMI methods. The permeability is mainly contributed by a small part of larger pore-throats (less than 30%) and the ratio of the smaller pore-throats in the samples increases with decreasing permeability. Although smaller pore-throats have negligible contribution on reservoir flow potential, they are very significant for the reservoir storage capacity. The pore-throats with average radius larger than 1.0 μm mainly exist in reservoirs with permeability higher than 0.1mD. When the permeability is lower than 0.1mD, the sandstones are mainly dominated by pore-throats with average radius from 0.1 μm to 1.0 μm. The ratio of different sized pore-throats controls the permeability of the tight sandstone reservoirs in different ways. We suggest that splitting or organizing key parameters defining permeability systematically into different classes or functions can enhance the ability of formulating predictive models about permeability in tight sandstone reservoirs. The PMI combined with QGF analyses indicate that oil emplacement mainly occurred in the pore-throats with radius larger than about 0.25–0.3 μm. This result is supported by the remnant oil micro-occurrence evidence observed by SEM and ESEM. [ABSTRACT FROM AUTHOR]

The tight sandstones of the Cretaceous Quantou formation are the main exploration target for hydrocarbons in the southern Songliao basin. Authigenic quartz is a significant cementing material in these sandstones, significantly reducing porosity and permeability. For efficient predicting and extrapolating the petrophysical properties within these tight sandstones, the quartz cement and its origin need to be better understood. The tight sandstones have been examined by a variety of methods. The sandstones are mostly lithic arkoses and feldspathic litharenites, compositionally immature with an average framework composition of Q 43 F 26 L 31 , which are characterized by abundant volcanic rock fragments. Mixed-layer illite/smectite (I/S) ordered interstratified with R = 1 and R = 3 is the dominating clay mineral in the studied sandstone reservoirs. Two different types of quartz cementation modes, namely quartz grain overgrowth and pore-filling authigenic quartz, have been identified through petrographic observations, CL and SEM analysis. Homogenization temperatures of the aqueous fluid inclusions indicate that both quartz overgrowths and pore-filling authigenic quartz formed with a continuous process from about 70 °C to 130 °C. Sources for quartz cement produced are the conversion of volcanic fragments, smectite to illite reaction and pressure solution at micro stylolites. Potassium for the illitization of smectite has been sourced from K-feldspar dissolution and albitization. Silica sourced from K-feldspars dissolution and kaolinite to illite conversion is probably only minor amount and volumetrically insignificant. The internal supplied silica precipitate within a closed system where the transport mechanism is diffusion. The quartz cementation can destroy both porosity and permeability, but strengthen the rock framework and increase the rock brittleness effectively at the same time. [ABSTRACT FROM AUTHOR]