Search

This paper proposes a systematic method for the identification of the load circuit parameters (say the $\boldsymbol{R}$ , $\boldsymbol{L}$ , and $\boldsymbol{C}$ elements) based only on the information of the instantaneous voltage and current measured at the point of common coupling (pcc). Geometric Algebra (GA) and concepts of differential geometry are used to produce a rigorous mathematical framework. The identification is formulated as a multidimensional geometrical problem that is solved conveniently by means of GA. Once the passive elements of the load have been identified, the active and reactive powers can be computed from first electromagnetic principles (Maxwell Equations). The theory is general and is verified with linear and nonlinear circuits. The paper shows single-phase circuits but the theory can be extended to three-phase circuits. The method is easy to program and has shown to be very robust for all tested cases. Because of its generality, the method presented will find applications beyond electric circuits. [ABSTRACT FROM AUTHOR]

Titanium tetrachloride (TiCl4) is a well-known source of titanium (Ti) for the formation of titanium nitride (TiN) barrier material in the semiconductor interconnection process; however, the reaction of by-products with airborne molecules can cause unexpected pump trips and equipment breakdown from the by-product powder build-up. Plasma scrubbers are used to decompose by-products, but hydrogen chloride (HCl) and nitrogen oxides are produced during and after the process. The process mechanisms change when the temperature and applied power of the heat source change. In this paper, we study the influence of the reactor temperature and applied power to the heat source on the decomposition capacity of TiCl4 in a plasma pretreatment system (PPS). We examine the effect of the temperature and heat source power to understand the reaction mechanisms for the composition and decomposition of gaseous species with chemical reactions through simultaneous methods. We analyzed the system with computational fluid dynamics (CFD) and chemical kinetic simulation to investigate the changes of the system mechanism. Subsequently, we achieved results for the correlation between the temperature of the reactor, power applied to the heat source, composition and decomposition of species, and chemical reaction mechanisms. [ABSTRACT FROM AUTHOR]

The fourteen papers in this special section focus on high performance light emitting diode (LED) drivers. In recent years, as the fourth generation of light source, light-emitting diodes (LEDs) have been widely used in many applications such as street lighting, automotive, and residential lighting because of their long lifetime, low maintenance requirement, and environment friendliness. As the performance of LEDs will be influenced obviously by the drivers, researchers have shown a growing interest in optimizing the drivers. Although these problems such as current balancing, eliminating electrolytic capacitor, and improving the topologies are not new, the high-frequency high-efficiency trend of LED drivers has given rise to additional challenges. These papers provide an insight on some of the newly emerging challenges and potential solutions to overcome those issues. [ABSTRACT FROM PUBLISHER]

This paper is aimed to compare the performance of toroidal inductors and planar spiral inductors in multilayered technologies, in terms of achievable inductance density. The optimization of planar toroidal inductors in multilayered substrates is investigated theoretically, and closed formulae are derived for their inductances as a function of geometrical parameters. The obtained model is validated by experimental results and electromagnetic simulation. From the comparison of the inductance of toroidal inductors and compact spiral inductors, a selection rule is proposed to choose the most suitable topology that leads to the most compact design. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive self-tuned current controller design for an LCL-filtered LC-tuned single-phase shunt hybrid active power filter (HAPF), which offers adaptability and flexibility of the control system to filter parameters changes. System modelling and online identification of parameters are presented. Then, a systematic self-tuned controller (STC) design is proposed to calculate the controller parameters and obtain the final control law adaptively. The exact HAPF parameters design is described and the overall closed-loop stability evaluation with considering digital control delay is discussed in this paper. To confirm the theoretical achievements, simulations and experimental tests on a real prototype system are performed. The results are in good accordance and demonstrate the effectiveness and superior performance of the suggested control technique. Furthermore, a comprehensive comparison between the proposed control technique and other controllers is provided to show the superiority of the proposed system from different aspects. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

This paper analyzes the unsymmetrical operation of the dc/dc MMC caused by parametric uncertainty. The unsymmetrical operation is referred to as the condition in which parameters involved in ac power generation are not equal in the phase-legs of the converter. Because existing models in the literature cannot exhibit the unsymmetrical operation of the dc/dc MMC, new detailed and simplified steady-state models are developed in this paper. In the developed models, the connection between the operation of different phase-legs shows itself when the dc-link impedance is considered. Using the developed models, the parameters that can force the converter to operate in unsymmetrical conditions are identified, and the maximum variation that the converter can tolerate is found. It is shown that even a small parameter variation leads to the leakage of the ac circulating current into the dc-link, which is not acceptable. By conducting various case studies, the impacts of the dc-link length, the transmitted power, and the conversion ratio on the unsymmetrical operation of the dc/dc MMC are characterized. The results showed that the converter would be more sensitive to the parameter variation as these parameters increase. Comparative analysis and simulation results confirm the validity and effectiveness of the presented models and analysis method. [ABSTRACT FROM AUTHOR]

In a previous paper, we introduced a modified Steinmetz equation to account for dc-bias field effects, which requires only a simple dc permeability measurement to predict total power loss. In this paper, we expanded our investigation to include Finemet nanocrystalline material and found that our modified Steinmetz formalism was effective in predicting dc-bias-related losses for this system as well. In this paper, it was observed that Finemet cores exhibit lower losses than Metglas cores under identical test frequencies and bias fields. In addition, we show that a full characterization of the dc loss component necessitates the consideration of higher order ( $n>1$ ) harmonic components. In order to quantify these higher frequency loss components, a dc–dc converter-based test system was built to intentionally introduce inductor current harmonics by varying the filter capacitance and parasitic inductance of the test system. Both core types were evaluated under fundamental frequencies of 20 to 150 kHz and dc-bias fields of up to 1.3 kA/m, with the inclusion of distorted waveforms obtained by varying filter capacitance. At higher frequencies, the Metglas cores were found to exhibit greater loss fractions associated with the higher order harmonic components. A detailed summary of the measured core loss characteristics for both core types is included and discussed. This paper includes the details of the measurements, the modified Steinmetz relation, and the loss extraction algorithm used for analysis. [ABSTRACT FROM PUBLISHER]

The quantitative analysis of the iron loss taking magnetic hysteresis behavior into account is essential for the development of high-efficiency electric machines. In a previous paper, a novel magnetic circuit model incorporating a play model, which is one of the phenomenological models of magnetic hysteresis, was proposed. It was clear that the proposed model can calculate the hysteresis loop of a ring core with high speed and high accuracy. However, this method was applied only for the objects with simple shapes. Thus, it is necessary to extend the applicable range for the objects with more complicated shapes. This paper presents a novel reluctance network analysis (RNA) model incorporating the play model and indicates the validity of the proposed RNA model by using a three-phase-laminated-core variable inductor as an object of discussion. [ABSTRACT FROM AUTHOR]

As part of the ongoing China Fusion Engineering Test Reactor (CFETR) studies, this work focused on the study of the electromagnetic (EM) loads distribution on inboard (IB) and outboard (OB) blanket vertical segments. In this paper, a major central disruption scenario with a 36-ms linear current quench was performed in the ANSYS finite element software. EM forces and moments, both on the single module and the complete blanket segment, were calculated for the updated helium-cooled ceramic breeder (HCCB) blanket. Furthermore, the effect of EM loads with respect to poloidal segmentations on the back plate (BP) was studied. Results show that the EM forces and moments in the IB blanket barely changed, but in the OB blanket, great changes occurred. With poloidal segmentations increasing, EM forces loads on the BP will be reduced. This paper may provide important data to support subsequent optimization of the BP of CFETR and could also be a technical reference for other fusion organizations. [ABSTRACT FROM AUTHOR]

This paper has introduced two important indexes, turn-off surge voltage (TSV) on power switch and peak positive pole potential (PPPP) of storage batteries, which can be used to evaluate switching transient process of high-voltage energy storage system. Research on them is of great significance to power switch choice and high-voltage isolation design in engineering applications. Power switch response process at the turning off moment and transient process in freewheel stage have been analyzed by the established small-signal model of single power switch; then, a power switch test platform for hybrid energy storage system was built to verify it. Taking pulsed-power supply charging device with a novel inductor of low resistance and high inductance as a research object, this paper has analyzed dynamic process of the TSV and the PPPP at the turning off moment through establishing state space model of the whole system. Comparison shows that the numerical curves match the simulated curves well. Finally, the exactness of the employed model has been further verified in two pulse capacitor charging experiments. [ABSTRACT FROM AUTHOR]

In this paper, a new configuration of dielectric-barrier discharge (DBD) reactor with three electrodes was manufactured and used to produce ozone. Designed flatly, this reactor is capable of establishing three different discharge modes from type of the volume and surface discharges, without modifying its internal structure. The aim of presenting this paper is to experimentally analyze the three discharge modes and their combination using a second channel to produce ozone. The two reactor channels are identical in terms of dimensions, material, and manufacturing process. Two frequency-adjustable pulse generators of the same electrical characteristics and two high-voltage transformers were used in the course of the experiments. The applied sinusoidal voltage is from 0 to 12 kVp-p. The frequency range was determined and fixed for all three discharge modes for the highest ozone concentration at a fluctuation rate of 1 L/min. Effects of increasing the applied voltage on the obtained concentration from the three different discharge modes were experimentally analyzed. Using the provided inlets–outlets, the effect of flowing gas through the length and width of the discharge area on ozone concentration was investigated, and appropriate flow directions were determined for the flowing gas under either of the three discharge modes. Experimentally results have been done for this three discharge modes as well as hybrid modes. The maximum ozone production rate achieved up to 14.52 g/h in the series combination of two different volume discharge. At 96% oxygen purity, ozone production yield, in two modes volume discharge VaDBD and surface discharge SDBD, have been improved up to 529.87 g/kWh. However, the total input power of the entire system is 120.2 W. [ABSTRACT FROM AUTHOR]

In the paper by Patra et al., a single-inductor multiple-output switcher was presented to produce buck, boost, and inverted outputs simultaneously. Unfortunately, this study showed some unexpected mistakes, especially in state-space equations and in the calculation of output voltages. The objective of this note was to provide correct analysis and rectify the errors in this paper. Some tables and equations have been modified that were present in the initial draft of this paper. The obtained parameters in this work could be an effective supplement and extension for the original work in the paper by Patra et al. [ABSTRACT FROM AUTHOR]

In inertial confinement fusion, the scientific issues include the generation and transport of driver energy, the pellet design, the uniform target implosion physics, and the realistic nuclear fusion reactor design. In this paper, we present a pellet injection into a power reactor in heavy-ion inertial fusion (HIF). We employ a magnetic correction method to reduce the pellet alignment error in HIF reactor chamber, including the gravity, the reactor gas drag force, and the injection errors. We found that the magnetic correction device proposed in this paper is effective to construct a robust pellet injection system with a sufficiently small pellet alignment error. [ABSTRACT FROM AUTHOR]

This paper addresses the mechanisms of wideband power amplifiers’ efficiency degradation in comparison with their narrowband operation. It starts by identifying some possible causes for this performance degradation, showing that the baseband terminations are dominant. A detailed explanation for the efficiency degradation is then presented, considering the scenarios where the most important baseband components fall before or after the resonance imposed by the bias and matching networks. A theoretical model that is able to describe this performance degradation is also presented. Finally, the proposed theory is validated through two implemented power amplifiers with the same fundamental and harmonic terminations, but with different baseband networks, showing that an optimized bias network design can improve the efficiency performance of a PA. [ABSTRACT FROM AUTHOR]

This paper will describe the influence of mesh geometry on the homogeneity of discharges, power, and efficiency of ozone generation. Homogeneous discharges increase the efficiency of the generation of ozone. Geometry of mesh electrodes affects the power and type of discharges, concentration, and efficiency of the ozone generation. The analysis of selected results indicates the need for the use of mesh electrodes with a small cross section at least $0.1\times0.1$ mm2 mesh to obtain a homogeneous discharge. The mechanism by which the geometry of mesh electrodes on the homogeneity of discharge is illustrated in this paper. Homogeneous discharges increase the efficiency of the generation of ozone that reduces the cost of ozone production. The results of the experimental studies show an increase in the average efficiency of 60% of the ozone generation and a 20% reduction in the demand for power with the constant concentration of ozone, justifies the problem. [ABSTRACT FROM AUTHOR]

Aiming at the fault traveling wave on the LCC-MMC HVDC transmission line, this paper analyzed its reflection and refraction characteristics at the DC buses and the fault point, plotted its propagation grid diagrams, obtained the relationship between the polarity of fault traveling wave and the boundary elements, and drew the conclusion that when the impedance of DC filter is far less than the wave impedance of transmission line, the existing fault location methods that need to distinguish these two waves according to their polarities are not applicable to the LCC-MMC HVDC system. On these bases, this paper proposed a modal traveling wave arrival time difference-based location principle for pole-to-ground fault, and a fault traveling wave propagation path ratio-based location principle for pole-to-pole fault, these principles neither need to identify the wave polarity, nor need the wave velocity value. In order to better extract the wave heads and their arrival time, this paper pre-treated the sampling data to make sure all the wave heads are extracted from the same frequency band, then the wave heads and their arrival time can be extracted with the empirical mode decomposition. The simulation results verified the effectiveness of the proposed fault location principle. [ABSTRACT FROM AUTHOR]

Light-emitting diodes (LEDs) are widely used in street lighting, landscape lighting, liquid crystal display (LCD) backlighting, healthcare, etc. As an important part of LED lighting products, LED driver plays a vital role in maintenance costs reduction, energy saving and lifetime prolongation. In this paper, a single-stage LED driver is proposed, which is integrated by a totem-pole bridgeless power factor correction (PFC) unit and several modular LCL-T resonant rectifiers. The totem-pole bridgeless PFC unit and the LCL-T resonant rectifiers are integrated by sharing switches, which can simplify the circuit and reduce the system cost. The output current can be regulated by applying the variable inductor control. Constant duty cycle and fixed switching frequency operation can be achieved as well. The operating principle and the performance of the proposed converter are analyzed in this paper. In addition, a precise parameter design method is proposed by considering the high-order harmonics. At last, an experimental prototype is established to validate the proposed parameter design and variable inductor control method. [ABSTRACT FROM AUTHOR]

This paper presents a new spiral inductor based on substrate integrated suspended line (SISL) technology. SISL is a new type of transmission line, which has many merits, such as low loss, low dispersion, and self-packaging. New series of spiral inductors based on this advanced SISL platform is proposed and modeled in this paper. SISL to microstrip transition is designed for the measurement of the SISL inductor, and an open-short deembedding method is introduced for the accurate extraction of inductor network parameters. A $\pi$ equivalent circuit model is applied for modeling of the SISL inductor and new double-sided SISL (DSISL) inductor, and the accurate empirical expression of inductance L$ , peak quality factor Q_{\mathrm {max}} , and self-resonance frequency are given. The typical relative error of each expression is less than 8%. Finally, a new DSISL inductor with patterned substrate is proposed, which can significantly improve the quality factor up to 40%. Simulation and measurement results show good agreement. [ABSTRACT FROM PUBLISHER]

This paper describes experimental verification of single-phase variable inductor prototypes rated at 2.4 kVAr (75 mH, 10 A, 230 V, 24 kg) and 12 kVAr (43 mH, 30 A, 400 V, 78 kg). Results for much smaller devices rated at 1-10 Var are also shown. The variability of inductance of the main AC winding was achieved by adding a DC winding, wound through the apertures placed symmetrically in the core such that both windings were magnetically orthogonal. Local saturation caused by the magnetic field due to DC winding creates virtual air gaps. This method is capable of lowering the main inductance by over 90% if no real air gap is present, but for industrial applications the range of variability is likely to be closer to 20-30% range, depending on the size of the real air gap in the magnetic circuit. The amount of variation/control can be improved by using more than one control winding. Very good repeatability of performance was observed, with relatively small total harmonic distortion introduced due to control. The experimental findings agree with a generalised analytical model. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

The main standard for avionic equipment DO-160G defines a set of tests that require compliance before the employment of a device in aircraft. An important test involves the generator voltage and consequential current distortion of the three-phase load in the variable 360–800 Hz frequency grid. The main purpose of this paper is to present and analyze a systematic design methodology for three-phase boost and buck rectifiers in order to meet with the voltage distortion test requirement. For a given voltage harmonic profile, the current harmonic limits that have to be satisfied are translated into equivalent per-harmonic admittances and a profile of maximum rectifier input admittance versus frequency is obtained. The defined profile, due to normalization, is applicable to arbitrary power level with simple shifting by the base admittance governed by the converter nominal power. It is shown that for boost-type rectifiers there is a tradeoff between current controller bandwidth and input inductor size, while for the buck-type rectifiers main limitation lies in the input LC filter design used for differential electromagnetic interference filtering. The experimental results conducted on an SiC three-phase 10 kW VIENNA rectifier are tightly backing up the proposed theoretical analysis. This paper is accompanied by three videos demonstrating experimental measurement of d-axis open-loop duty cycle to inductor current transfer function, loop-gain of d-axis current controller with 3.8 kHz bandwidth and variable grid frequency 360–800 Hz operation of the converter under 0% and 10% input three-phase voltage total harmonic distortion. [ABSTRACT FROM AUTHOR]

With the rapid development of photovoltaic and fuel cell stacks, high voltage gain converters are urgently demanded. Conventional boost is limited by the exaggerated duty cycle, it is impossible to obtain a high voltage gain while ensuring efficiency. Therefore, a zero-voltage switching (ZVS)-modified SEPIC converter that combines a voltage multiplier cell with traditional SEPIC is proposed in this paper. With detailed parameters design process, this presented converter works at zero voltage switching (ZVS), while obtaining high voltage gain without extremely high duty cycle. Besides, voltage stress is also reduced and low-voltage component with lower parasitic parameters can be used, thus efficiency is maintained. In order to further improve the power density, an integrated inductor scheme is adopted in this paper without changing intrinsic working states of the two inductors. A 36-W prototype is built, and experiments are conducted to verify the advantages of the proposed converter. The efficiency is up to 91.5% at full load. [ABSTRACT FROM AUTHOR]

Active cell balancing is the process of equalizing the State-of-Charge (SoC) of all cells in a series-connected battery pack via charge transfers. While several balancing architectures and equalization strategies exist in the literature, optimization of the circuit components in a balancing architecture has not been sufficiently studied so far. Intuitively, one would select components with low parasitic resistances to minimize the energy dissipation. However, as will be shown in this paper, this might not be an optimal choice in most situations. In this paper, we propose an optimization framework that performs an efficient design space exploration to identify the energy-efficient circuit configuration of a balancing architecture. Moreover, for the first time, we propose a methodology to obtain the optimal operating frequency of an active cell balancing architecture and a control circuit to maintain the operation at the optimal frequency. For this purpose, we derive a closed-form analytical model of the charge transfer process with which we obtain the performance metrics required for our framework. Case studies show that such optimally dimensioned active cell balancing architectures operated at the optimal frequency reduce the energy dissipation by approximately 49% compared to the intuitive approach of selecting components with least parasitic resistances. [ABSTRACT FROM AUTHOR]

In this paper, a laser headlight power converter (LHPC) was developed to drive the InGaN-based blue beam laser diode (BBLD). The LHPC was composed of the four–switch step-up step-down converter (FSSUSDC), the FSSUSDC controller, and the current error compensator (CEC). When the BBLD dynamic resistance was increased under the high ambient air temperature, the FSSUSDC operated in the step-down mode, and the CEC employed the proportional-integral control, the BBLD driving current exhibited an ignition current spike, which could destroy the semiconductor material of the BBLD, resulting in optical output power decay. Therefore, a new four-gradation gain (FGG) control method was proposed to mitigate the ignition current spike of the BBLD. This paper presented the BBLD temperature characteristic, an analysis of the LHPC ignition current, a CEC compensation design, and an analysis and design of the FGG control. [ABSTRACT FROM AUTHOR]

This paper provides an experimental discussion on a real-time real-power emulator that plays an important role in achieving a total test of medium-voltage, high-power, high-speed induction motor drives. The use of the emulator brings cost and time savings to the test. The test bench including the emulator is characterized by connecting two modular multilevel double-star chopper-cell (DSCC) converters connected in a front-to-front way. This paper designs, builds, and tests a 400- ${\rm V}_{\rm dc}$ , 10-kW downscaled test bench. It mainly consists of the following two identical DSCC converters: 1) one DSCC converter is used as an inverter under test; and 2) the other as a real-time real-power high-fidelity emulator. Experimental waveforms confirm that the emulator can reproduce electrical and mechanical operating performance of the three-phase 200-V, 10-kW, four-pole, 9000-r/min induction motor loaded with a centrifugal compressor. [ABSTRACT FROM AUTHOR]

A high-frequency high voltage gain discontinuous conduction mode coupled-inductor boost LED driver based on planar component is presented in this paper. GaN switch is adopted with lower conducting resistance and higher switching speed. Zero voltage switching (ZVS) is achieved at the same time to reduce high switching loss caused by high switching frequency. Compared with the previous work, the voltage gain is higher and efficiency is higher because of ZVS. This paper focuses on high efficiency; therefore, resonant gate driver is adopted and efficiency is increased by 0.6%. In terms of the coupled-inductor, planar component is used and parameter optimization is also proposed to realize lower loss, including wingding loss and fringing loss caused by the air gap. A 500 kHz 36 W prototype has been designed to demonstrate theoretical analysis. In addition, comparison of drive loss between the resonant gate driver used in this paper and conventional driver implemented by Si8271 is made, revealing advantages of the resonant driver. Obtained efficiency was up to 92.1% at full load. [ABSTRACT FROM AUTHOR]

The use of electronic equipment and other dc-compatible appliances in homes and offices is increasing at a very fast rate, as well as the distributed generation of energy. These two statements will most likely trigger, in a near future, the adoption of district-scale dc grids, connecting dc microgeneration plants and consumers, in an effort to cut the number of conversion steps required to deliver power to dc appliances. DC–DC converters will be fundamental in these systems, allowing the establishment of several voltage levels. The reliability of these converters plays a critical role, ensuring service continuity of the loads connected to them. With the increment of reliability in mind, this paper proposes a simple yet effective open-circuit fault diagnostic method suitable for interleaved dc–dc boost converters, but equally functional for other dc–dc converter topologies. The improvements introduced in this paper greatly simplify the diagnostic action, while making the correct diagnostic of faults independent of the switching duty cycle. Moreover, an alternative reconfiguration scheme is proposed to mitigate the adverse impacts of such faults. To prove the effectiveness of these strategies, a three-phase interleaved boost converter prototype was used in the experiments. [ABSTRACT FROM AUTHOR]

A DC system saturated core fault current limiter (DCSFCL) was proposed to limit the fast rising trend of fault current in HVDC system. However, traditional method to calculate and design the DCSFCL tend to neglect leakage flux around the permanent magnet (PM), leading to large calculation error and inappropriate design procedure. The novel contribution of this paper is that it proposed a modularization method to analyze the permeance of both PM and adjacent air. Hence, the leakage flux effect is considered properly and a more accurate permeance matrix can be derived in a pure mathematical way. In this case, DCSFCL can be calculated much faster than the FEA simulation program with a promising accuracy regarding fault limiting performance. More importantly, design flow of the DCSFCL and related PM biased devices was given as well. Calculation result shows that inductance value calculated by the proposed method has less than 1% error compared with fine meshed FEA simulation result and about 20% increase in accuracy compared with traditional method that neglects PM leakage flux effect. Prototype of the DCSFCL was also built and experimental tests were carried out to verify the correctness of the proposed method. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

This paper offers a new approach for far-field high-resolution imaging of conducting obstacles based on arrays of frequency-multiplexed subwavelength resonant elements. Each resonator is a circular aperture in a metallic screen that is strongly miniaturized by means of loading by a thin epsilon-negative and near-zero metamaterial (MTM) liner. Each MTM-lined aperture exhibits a fano-shape transmission profile, i.e., a peak followed by a minimum, and the resonance frequencies of different apertures are chosen such that the resonance of one lies within/very close to the antiresonance of the other to ensure strong decoupling. This paper shows that blocking an aperture using a conducting disc removes the corresponding resonance peak/minimum from the transmission/far-field amplitude spectrum, enabling far-field detection of any distribution of such obstacles with a spatial resolution determined by the aperture sizes, which measure less than one-sixth of free-space wavelength at their respective resonance frequencies. The proposed imaging mechanism is verified through full-wave HFSS simulations as well as far-field measurements. Some challenges associated with this approach are then discussed. [ABSTRACT FROM AUTHOR]

This paper presents a shutdown dose rate (SDR) calculation to estimate a newly developed preliminary concept of the equatorial port model for the Korean fusion demonstration reactor (K-DEMO). The equatorial port model was designed to provide effective radiation shielding abilities adopting the port shielding block and labyrinth structure, which was integrated into the modified K-DEMO neutronic analysis model by the Monte Carlo automatic modeling system. A rigorous two-step method was applied to couple transport (MCNP) and activation (FISPACT) codes according to three steps of calculation procedures. The results of neutron flux and decay gamma transport calculation for the equatorial port area have been indicated in this paper. The SDR calculation result near the equatorial port area reveals that a dose level in the equatorial port interspace was below $100~\mu $ Sv/h after 12 days of the shutdown. Shielding blocks and two labyrinth structures prove that they effectively attenuate neutrons on the current concept of the equatorial port model. [ABSTRACT FROM AUTHOR]

The demand on mobile electronics to continue to shrink in size while increasing in efficiency drives the demand on the internal passive components to do the same. Power amplifiers require inductors with small form factors, high quality factors ( Q\texts ), and high operating frequency in the single-digit gigahertz range. This paper explores the use of magnetic materials to satisfy the demands of power amplifier inductor applications. This paper then discusses the optimization choices regarding material selection, device design, and fabrication methodology. The inductors achieved here present the best performance to date for an integrated magnetic core inductor at high frequencies with a 1-nH inductance and peak $Q$ value of four at about 3 GHz. Such compact inductors show potential for efficiently meeting the need of mobile electronics in the future. [ABSTRACT FROM AUTHOR]

A variable inductor consists of a magnetic core, primary dc windings, and secondary ac windings. The effective inductance of the secondary ac winding can be controlled by the primary dc current because of its nonlinear magnetic characteristic. Hence, variable inductors can be applied as a reactive power compensator for voltage stabilization in electric power systems, and have desirable features such as a simple and robust structure, low cost, and high reliability. In a previous paper, a concentric-winding-type three-phase variable inductor with a 2-D structure has been proposed. It was demonstrated that the 2-D variable inductor has good controllability and a low distortion current. To further increase productivity and reduce costs, this paper presents a novel concentric-winding-type three-phase variable inductor with a 3-D structure. It is demonstrated that the leakage flux of the proposed 3-D variable inductor is reduced by more than 30%. Furthermore, a 6.6 kV–100 kVA 3-D variable inductor is designed and compared to its 2-D counterpart. It is proved that eddy current loss, which is induced within an oil-immersed self-cooled tank because of leakage flux from the variable inductor, can be reduced to one-third of that of the 2-D variable inductor. [ABSTRACT FROM AUTHOR]

This paper presents a new soft switching high voltage gain interleaved dc-dc converter with a three-windings coupled inductor for a fuel cell vehicle. Two interleaved and intercoupled boost cells are connected by the input parallel and output series (IPOS) configuration, realizing low input current ripple and high voltage gain simultaneously. All power switches can operate under soft switching conditions by only adding a simple auxiliary circuit composed of one auxiliary inductor and one power switch. Besides, the auxiliary inductor is coupled with the main inductors, which results in a rapid zero convergence of the auxiliary current and a small conduction loss of the auxiliary circuit. The operating principle, steady state characteristic, comparison with other converters, and parameter design are analyzed in this paper. Finally, the main characteristics of the proposed converter are verified by a 1-kW laboratory prototype. [ABSTRACT FROM AUTHOR]

When a fault occurs on the dc side of the voltage source converter based high voltage direct current (VSC-HVDC) transmission system, the fault current rises quickly due to the low damping of the dc system. Using a dc fault current limiter (DC-FCL) to limit the rise of the fault current can significantly reduce the breaking requirements of the DCCB. A topology of a bidirectional active dc fault current limiter (BA-FCL) based on coupled inductor is proposed in this paper. No expensive full-controlled power electronic devices are used in this topology. Only a few half-controlled power electronic devices are used to achieve active control of the current limiting unit. Compared with many topologies of current limiter at present, the fault current limiting effect of BA-FCL is improved significantly while the cost, volume, topology complexity, and control complexity are reduced. The stress analysis and parameter design of the proposed current limiter are carried out. Finally, the simulation case study and hardware experiment are implemented to verify the good economy and current limiting performance of the proposed topology. [ABSTRACT FROM AUTHOR]

The use of VSC-HVDC grids for offshore wind farm integration will require the use of dc breaker systems and presently they require dc reactors to limit the rate of rise of fault current. The introduction of large dc reactors throughout a VSC-HVDC system can have a significant impact on its stable operation and will require additional control. This paper analyzes this problem and proposes a PSS-like control (DCPSS) to aid dc grid stability and cope with this effect. A generalized analytical model for studies on dc voltage control is presented. Key stability and transient performance issues caused by the use of the dc reactors in a multiterminal system are investigated by analyzing poles, zeros, and frequency responses of open-loop and closed-loop models. Design and location identification methods for the DCPSS are provided. An excellent damping enhancement is achieved by this controller. The analytical studies and time-domain simulations in this paper are performed based on two VSC-HVDC models. [ABSTRACT FROM AUTHOR]

This paper suggests a cascade output voltage regulation strategy for dc/dc boost converters that embeds a robust inner-loop current controller against parameter variations. The contributions of this paper are divided into two parts. The first contribution is to present a simple and robust inner-loop current controller despite parameter uncertainties, guaranteeing the stability of the whole closed-loop system including the first-order internal dynamics. The second contribution is to show that an outer-loop proportional–integral regulator can stabilize the output voltage error without relying on any parameter information. Simulations and experiments using a 3-kW dc/dc boost converter showed that the proposed method offers satisfactory closed-loop performance in the presence of parameter uncertainties. [ABSTRACT FROM PUBLISHER]

This paper investigates the Multilevel Current Source Converter (MCSC) STATCOM. It proposes a new method of modulation. The new modulation method produces less THD and di/dt at the terminals of the MCSC STATCOM when compared to the widely used Phase-Shifted Carrier SPWM (PSC-SPWM). To ensure the inductors' currents remain balanced, a Current Balancing Algorithm (CBA) is presented. The CBA does not require any controls. It relies on assigning optimum switching states to each CSC module in real-time. In addition, two control strategies are presented in this paper. The first one assumes the STATCOM to be a SISO. Therefore, it only requires one PI controller. However, the gains for the controller must be changed if the STATCOM was to transition from capacitive mode to inductive mode, or vice versa. The second control strategy overcomes this problem by implementing a TITO integral state feedback controller. The contributions of this paper are validated via simulation and experimental results. [ABSTRACT FROM AUTHOR]