Search

In this study, the space charge in oil-impregnated thick pressboard and Kraft paper were measured by the pulsed electroacoustic (PEA) method from -20 to +60 °C. A bipolar charge transport model was used to simulate the transport processes of homocharge and heterocharge, and the acoustic attenuation process in the samples. The test results show that space charge accumulates in the thick pressboard and Kraft paper increases first and then decreases with temperature, and its maximum appears at 40°C, while little space charge accumulates at -20°C. The space charge near the lower electrode shrinks in the oil-impregnated thick pressboard at high temperature and the shrinkage is larger at 60°C. In the oil-impregnated Kraft paper, the accumulation and charge density of positive charge is different from negative charge. The ion transport process model simulates the charge shrinkage near the electrode, and disappears at the upper electrode after the acoustic attenuation simulation. The model established in this paper can well simulate the space charge distribution of oil-impregnated thick pressboard and Kraft paper under different temperatures. [ABSTRACT FROM AUTHOR]

The paper presents the application of the Cole-Cole model for determining the runs of the return voltage of the paper-oil insulation sample through a computer simulation. Different insulation conditions were simulated through an adequate selection of parameters a and T of the Cole-Cole model. For calculation purposes, a series - parallel substitute scheme, obtained through approximation of discrete characteristic operator impedance Za of the model applied, was used. The diagnostics of the simulated insulation condition was based on the analysis of a few selected parameters of the return voltage, obtained from time characteristics. [ABSTRACT FROM AUTHOR]

In this paper the accelerated aging experiments of oil-paper insulation are carried out to simulate the oil-paper aging process under normal thermal aging process. On the basis of the results of accelerated aging experiments, how the deviation degree of aging status change under the same aging factors is studied, and a method to calculate the failure probability due to the loss of mechanical strength of the insulation is put forward. This paper presents an approach for economic assessment on insulation diagnosis through accelerated aging experiments. The foundation of this approach for economic assessment on insulation diagnosis is to establish condition simulation method of triple relationships between condition status, aging time and failure probability according to data from accelerated aging experiments. The conclusions are made that the economic and technical factors can affect the optimum life cycle cost of each maintenance strategy, which consequently affects the economic feasibility of condition-based maintenance strategies. [ABSTRACT FROM AUTHOR]

The article reports on research into sketch-understanding systems for tablet personal computers (tablet PC). It discusses the work of the Sketch Understanding Group, of which the author is a member, at the Massachusetts Institute of Technology (MIT) on developing a "magic paper," or "intelligent paper," a paper-like surface that can convert sketches of physical systems into animated computer graphics. Sketch-understanding systems go beyond traditional computer-aided design (CAD) programs that produce diagrams, and beyond handwriting recognition systems.

This column discusses the 2015 ISCA Influential Paper Award, which recognized "Wattch: A Framework for Architectural-Level Power Analysis and Optimizations" by David Brooks, Vivek Tiwari, and Margaret Martonosi. [ABSTRACT FROM AUTHOR]

This paper proposes a new method to improve re performance of intra-field interpolation which is the mos~ important element of deinterlacing method. Traditional edge- based methods were poor at determining accurate edge iirection which decides interpolation performance. The 7roposed method decides the direction and slope of edge based on locally adaptive-thresholded binary image to mprove efficiency and accuracy, and it also increased the ~orizontal size of search window to 15 for better direction ietermination at gentle slope. Compared to traditional edge- based methods, interpolation based on binary image, which is ,`enerated using the proposed method, leads to great erformance improvement. With computer simulations for a ~`ariety of images, this paper shows the new approach is much ~etter than traditional methods.. [ABSTRACT FROM AUTHOR]

This paper presents an implementation of an ~daptive beamformer in a hands-free unit. The proposec~ ~daptive beamformer suppresses stationary noise an~ nterference sound. The adaptive beamformer and acoustic `cho canceller were implemented in a compact hands-free mit with a low-cost DSP. Experimental results demonstrate he noise reduction performance of the hands-free unit'. [ABSTRACT FROM AUTHOR]

Beginning with the June issue of the Transactions, papers will be separated into two categories; Part A — Dielectric Fundamentals and Part B — Dielectric Applications. Professor Huseyin Hiziroglu of Kettering University is the co-editor of Part A papers and Professor Giovanni Mazzanti of Bologna University is the co-editor of Part B papers. [ABSTRACT FROM AUTHOR]

Wind turbine generators in a windfarm are connected by underground cables. Lightning sometimes strikes a nacelle or a blade. Lightning overvoltages due to a direct lightning strike to the system cause damages in the underground cable. Many parameters should be investigated to establish a rational lightning protection design for wind power generation system. Numerical simulation is a useful method to discuss the influence of the parameters on the lightning overvoltages. This paper uses an Electro-Magnetic Transients Program for the lightning surge analysis. This paper discusses the influence of grounding method of metallic sheath of the cable and grounding resistance on the lightning overvoltages for the direct lightning strike to the generation system. [ABSTRACT FROM AUTHOR]

The article presents information on the topics such as modeling, simulation, and analysis of social systems covered by the journal IEEE Transactions on Computational Social Systems and the names of the websites where the papers can be submitted.

Describes the above-named upcoming special issue or section. May include topics to be covered or calls for papers. [ABSTRACT FROM AUTHOR]

This paper presents new results on a novel coupled-physics modality called magneto-acousto-electrical tomography (MAET). With static magnetic field, a beam of ultrasound is applied to the sample to be imaged; the ultrasonic vibration can lead to the separation of the charges due to the Lorentz force and produces the current distributed in the object. In this paper, simulations were conducted on biological tissue model, and the electrical properties were reconstructed, which could reflect the state of physiological or pathological. We also conducted experiments to detect the voltage signal of microvolt level by the electrodes placed around the sample. The series of experiments were conducted on low-conductivity (0.2 S/m) animal gelatin phantom and real biological tissue, successively placed in a 260 mT magnetic field and sonicated with a plane ultrasonic transducer of central frequency 2.25 MHz. In this paper, we obtained axis resolution of 1 mm, much more significant improvement than the previous reports. More importantly, the experimental result does also demonstrate the feasibility of MAET to image the electrical properties of biological tissue. [ABSTRACT FROM AUTHOR]

In this paper, a quad-mode endfire planar phased antenna array with wide scan angle and 1.2 mm clearance is proposed for 5G mobile terminals. The proposed antenna can obtain over 8 GHz of impedance bandwidth. In this paper, it is suggested to efficiently combine a multimode array element with different radiation patterns for each mode into a phased antenna array. In the array, similar and wide embedded radiation patterns are obtained for the all four modes. Furthermore, a coaxial to differential stripline transition is designed in this paper. The differential feeding structure is very compact and utilizes only MMPX connector and vias. The total scan pattern and coverage efficiency of the measured and simulated phased array antenna are calculated in the range from 25 to 33 GHz, and good agreement between measured and simulated results is observed. The mean coverage efficiency along the frequency range is very similar, but minor difference in variance of coverage efficiency is observed in the measurements. The coverage efficiency of around 50% for the threshold gain of 5 dBi is achieved in the chosen frequency range. [ABSTRACT FROM AUTHOR]

In the system and control community, the sliding mode control technology has been known as a tool which is able to handle system uncertainties and external disturbances. Simplicity in implementation and good stability performance are the other interesting features of the sliding modes. However, traditional sliding mode controllers exhibit two weaknesses, as follows: 1) generally, they have asymptotic stability in sliding mode dynamics which results in a slow speed system and 2) the so-called chattering phenomenon exists, which produces undesirable high frequency oscillations in the control signal. In this paper, the former problem is solved using a twofold terminal sliding manifold displaying desired transient and steady state behavior. The latter issue is responded to by a twofold sliding mode technology which leads to a continuous sliding control rule instead of a discontinuous switching control. The effects of uncertain terms as well as external perturbations with unknown bounds are fully compensated using updated parameters. The values of the updated parameters approach fixed values as the system trajectories converge to the equilibrium states. The analytical results of this paper are theoretically proved using the Lyapunov technique and the finite-time control strategy. Comparative computer simulations on a robotic manipulator confirm the fast convergence attribute and robust performance of the introduced adaptive robust nonsingular terminal sliding control algorithm. [ABSTRACT FROM AUTHOR]

This paper presents a simulation study of the dynamics of dust grains around a small asteroid. Plasma-asteroid interactions and asteroid charging are obtained from fully kinetic particle-in-cell simulations. Dust transport simulation takes into account the electrostatic force, solar radiation pressure, and the gravitational force. Both the result derived from laboratory measurements of regolith surface charging and the single dust charging model are considered for dust charging. For the small asteroid considered in this paper, we find that dust transport is mostly determined by the competition between the electrostatic force and the solar pressure and dust distribution is sensitive to both dust charging and dust grain size. For dust grains in the tens of micrometer size range, the solar radiation pressure dominates dust transport at small dust charge-to-mass ratio, whereas the electrostatic force dictates dust transport at large dust charge-to-mass ratio. [ABSTRACT FROM AUTHOR]

The article offers information on the publication of "IEEE Transactions on Computational Social System" and topics covered under the publication which include modeling, simulation and understanding of social system from computational perspectives. The article covered in the publication include social network dynamics, social intelligence and cognition, and computational behavior modeling.

This paper is dedicated to study the experimental validation of a numerical model based on La-Fe-Co-Si layered operating near room temperature. For the purpose of this paper, a numerical simulation based on the transient energy equations is proposed for modeling the heat exchange between the multilayer material and the carrier fluid in the regenerator bed with an applied magnetic field of 1.5 T. The main findings of the simulation show a comparison between the numerical model and experimental setup including the magnetocaloric effect of La-Fe-Co-Si, pressure drop, and exergy and exergetic efficiency. [ABSTRACT FROM AUTHOR]

Due to the rapid advances taking place in the development and application of GaN electronics, there is an immediate need to take cognizance of the recent technological improvements and bring the potential and opportunities that exist in the area to a wider device community. The primary goal of this special issue is, therefore, to put together works in different aspects, including modeling, design, technology, characterization and applications so that this special issue will not only be of great archival value but also attract new researchers into this area for Digital Object Identifier 10.1109/TED.2013.2278653 further accelerating the application of III-N devices in building reliable, cheaper, and high-performance electronic systems. The papers collected in this special issue have been grouped into six topics. They are: 1) Fabrication and characterization of GaN-based devices. 2) High power GaN HEMTs for power switching applications. 3) High speed GaN HEMTs for RF applications. 4) Reliability and parasitic issues in GaN HEMTs. 5) Simulation-based development of GaN HEMTs devices. 6) GaN-based low noise amplifiers and gate drive circuits. [ABSTRACT FROM AUTHOR]

This paper contributes to the accurate and efficient computation of control system equations in electromagnetic-transient simulation tools. The proposed approach is based on the formulation of a reduced rank Jacobian matrix in a fully iterative Newton method. In addition, this paper compares the accuracy and efficiency for the proposed method's variants, including a hybrid approach with a fixed-point solution. [ABSTRACT FROM PUBLISHER]

This paper describes the output performance of a strapped vane type 2.450 ± 0.030-GHz magnetron in the presence of a dielectric material. A 3-D particle in cell software computer simulation technology has been used for this study. The side resonators (cavities) of the magnetron are partially filled with a low-loss dielectric material ( \varepsilon r=11.7 and tan \delta =3.5\times 10^-6 ). The efficiency and output power of the magnetron have been increased by 2% and 10%, respectively, by dielectric material filling. It has been found that oscillation start-up time of magnetron is not directly affected by dielectric material filling as described in previous research papers. In addition, it has also been found that magnetron output performance remains almost the same for the lossless and the low-loss dielectric material. [ABSTRACT FROM PUBLISHER]

The high-voltage direct current cable insulations consist of polymeric or mass-impregnated paper materials. Their electric conductivities depend on the electric field and the temperature. Losses inside the conductor and in the insulation increase the temperature, resulting in increased losses and in a possible thermal runaway process. In this paper, coupled electro-thermal field simulations including nonlinear field-dependent conductivities are carried out. With a varying applied voltage and a current in the conductor, the condition for a thermal breakdown is computed. To compute the losses inside a 1-D insulation model, the finite-difference method is used. The simulation results conform well to experimental measurements. An approximation of the condition for a thermal breakdown is developed and show equal results in comparison to the coupled electro-thermal field simulations. [ABSTRACT FROM AUTHOR]

Vacuum interrupter is widely used in the medium-voltage power system. Controlling the arc by the magnetic field is an effective method to improve the breaking capacity. The transverse magnetic field (TMF) forces the constricted arc to rotate to reduce local overheating. In this paper, three kinds of TMF contacts, which are Swastika-type contact, cup-shaped contact, and double-TMF contact that combines Swastika-type and cup-shaped contacts coaxially, are investigated in a demountable vacuum chamber with a high-speed camera. The arc voltage and current are also recorded. The experiments were conducted with circuit currents from 5 to 20 kA (root mean square) with a frequency of 50 Hz. There are four current levels in the experiment, which are 5, 10, 15, and 20 kA, and at least three tests are taken for each current level. The results showed that under low current (I = 10 kA), the arc of the three TMF contacts did not rotate. Under high current (I = 20 kA), it was observed that the arc of Swastika-type and double-TMF contacts rotated in the gap. The arc speed of double-TMF contacts is higher than that of Swastika-type contacts. The cup-shaped contacts have the highest arc voltage and noise among the three TMF contacts. The Swastika-type contacts were eroded most seriously. The simulation results show the force distribution of the arc on different locations. The resultant force makes the arc rotate counterclockwise. [ABSTRACT FROM AUTHOR]

This paper is an extension of the procedure pointed out to evaluate the distortion of the exponential signal, modeled as multiexponential signal with different amplitudes and time constants. This procedure evaluates the distortion by applying the Prony-like method to the signal reconstructed by zero-crossing time evaluated on the difference between the exponential original signal and the reference sinusoidal one. The extension proposed in this paper concerns with the use of the low-chirp signal as reference instead of the sinusoidal signal. The low-chirp signal permits to increase the number of the zero-crossing time in the section of exponential signal with the higher slope and decreasing in the section with the lower slope. This setting permits to estimate the distortion of the exponential signal with higher accuracy and precision. The parameters’ amplitude, phase, and start frequency of the reference low-chirp signal are used to reconstruct the exponential signal in the zero-crossing time in order to overcome the problem of the high-resolution sampling. Their estimation is carried out by the time-varying sine-fitting algorithm that processes the resulting signal that is the difference between the exponential original signal and the low-chirp signal. Advantages of the proposed extended procedure regard the direct estimation of the reference low-chirp signal parameters from the resulting signal over-sampled at low resolution, and the use of only one input acquisition channel that permits to overcome the synchronization problem between the reference and the resulting signal. The numerical and experimental tests validate the extended procedure. [ABSTRACT FROM AUTHOR]

Faster-than-Nyquist (FTN) transmission employing antenna polarization multiplexing and higher order modulation (HoM) schemes can significantly increase the spectral efficiency (SE) of the existing wireless backhaul links. However, the benefits of each of these SE enhancement techniques come with a price. While FTN introduces inter-symbol interference, a dual-polarized (DP) transmission suffers from cross-polarization interference (XPI), and HoM makes a communication system vulnerable to phase-noise (PN) distortions. In this paper, we investigate, for the first time, a DP-FTN HoM transmission system. We propose a XPI cancellation and PN mitigation structure, coupled with adaptive decision-feedback equalization or linear precoding, to jointly mitigate interference and accomplish carrier-phase tracking. The DP systems combined with the FTN signaling presented in this paper offer more than 150% increase in SE compared with a single-polarized Nyquist transmission. The effectiveness of the proposed algorithms is demonstrated through computer simulations of a coded DP-FTN microwave communication system in the presence of PN. Numerical results suggest that with the proposed interference cancellation methods, a DP-FTN transmission can yield a 3–5.5-dB performance improvement over an equivalent DP-Nyquist system that employs a higher modulation order to achieve the same data rate. [ABSTRACT FROM AUTHOR]

Magnetic flux leakage (MFL) response predicting is important for defect estimation. This paper first proposes a concept of basic signal by discovering the combination property of the MFL response. The basic signal can be used to predict the MFL response conveniently by a basic signal combination method (BSCM), which is also innovatively put forward in this paper. In this method, the basic signal is calculated in advance, and the MFL response can be calculated by several transformation and combination operations. Both the simulation and experimental results demonstrate the feasibility of BSCM. Compared with other traditional methods (magnetic dipole method and finite-element method), BSCM shows a good performance on both the computational speed and accuracy. [ABSTRACT FROM AUTHOR]

Through numerical simulations and calibrated experiments, the aim of the work presented in this paper is placed on the development of a polarity changeable magnetizing platform for a rotary magnetic encoder using a permanent magnet and thin silicon steel plate. Parameter studies are conducted via finite-element analyses to obtain optimized geometric design parameters for the magnetizer, leading to desirable magnetic flux density and effective magnetized patterns on the magnetic media. [ABSTRACT FROM AUTHOR]

This paper proposes a leader–follower-based model of mobile molecular communication networks for target detection applications. The proposed model divides the application functionalities of molecular communication networks into two types of mobile bio-nanomachine: leader and follower bio-nanomachines. Leader bio-nanomachines distribute in the environment to detect a target and create an attractant gradient around the target. Follower bio-nanomachines move according to the attractant gradient established by leader bio-nanomachines; they approach the target and perform necessary functionalities, such as releasing drug molecules. This paper develops mathematical expressions for the proposed model, describes wet laboratory experiments designed to estimate model parameters, and performs biologically realistic computer simulation experiments to evaluate the performance of the proposed model. The main contributions of this paper are to demonstrate the functional division of molecular communication networks, which will facilitate the design and development of molecular communication networks. Furthermore, insight into the application-level performance of molecular communication networks will be provided based on the proposed model. [ABSTRACT FROM PUBLISHER]

The risk of unstable subsynchronous oscillations (SSO) in DFIG-based wind parks radially connected to transmission lines with series capacitive compensation is typically assessed with numerous electromagnetic transient (EMT) simulations, which is a time-consuming process. However, not all operating scenarios present risk of SSO and require such a detailed investigation. This paper proposes two charts based on impedance equivalents of wind generators obtained through frequency scans to quickly map which combinations of parameters can create unstable SSOs and which combinations are risk-free. With the information, engineers can immediately filter out scenarios with no risk of instability and conduct detailed studies on fewer scenarios that are truly critical. These charts can be obtained with simple equations that use only information readily available in practice to engineers, without the need to run any computer simulation. The charts also reveal the key operating conditions that can increase the risk of an unstable SSO and provide real-time quantitative insights into how close a wind park is to an instability. Application examples are provided to illustrate how this approach can help engineers speed up studies to identify the risk of SSO. [ABSTRACT FROM AUTHOR]

Orthogonal/vector approximate message-passing (AMP) is a powerful message-passing (MP) algorithm for signal reconstruction in compressed sensing. This paper proves the convergence of Bayes-optimal orthogonal/vector AMP in the large system limit. The proof strategy is based on a novel long-memory (LM) MP approach: A first step is a construction of LM-MP that is guaranteed to converge systematically. A second step is a large-system analysis of LM-MP via an existing framework of state evolution. A third step is to prove the convergence of state evolution recursions for Bayes-optimal LM-MP via a new statistical interpretation of existing LM damping. The last is an exact reduction of the state evolution recursions for Bayes-optimal LM-MP to those for Bayes-optimal orthogonal/vector AMP. The convergence of the state evolution recursions for Bayes-optimal LM-MP implies that for Bayes-optimal orthogonal/vector AMP. Numerical simulations are presented to show the verification of state evolution results for damped orthogonal/vector AMP and a negative aspect of LM-MP in finite-sized systems. [ABSTRACT FROM AUTHOR]

The flexibility in transmission networks is not fully utilized in existing energy management systems (EMSs). Corrective transmission switching (CTS) is proposed in this two-part paper to enable EMS to take advantage of the flexibility in transmission systems in a practical way. This paper proposes the following two EMS procedures: first, Procedure-A connects real-time security-constrained economic dispatch (RT SCED) with real-time contingency analysis (RTCA), which is consistent with industrial practice; and second, Procedure-B, an enhanced version of Procedure-A, includes CTS in EMS with the proposed concept of branch pseudo limit used in RT SCED. Part-I of this paper presents the methodology, whereas Part-II includes detailed results analysis. It is demonstrated that Procedure-A can effectively eliminate the base case overloads and the potential post-contingency overloads identified by RTCA, and Procedure-B can achieve significant congestion cost reduction with consideration of CTS in RT SCED. Numerical simulations also illustrate that integrating CTS into RT SCED would improve social welfare. [ABSTRACT FROM AUTHOR]

This paper is devoted to the further development of a numerical model for the simulation of high-current vacuum arcs (HCVA) with cathode attachment in the form of multiple cathode spots. The model allows one to simulate different modes of HCVA and the transition between them. It is shown that the secondary plasma, arising from the anodic sputtering and nonadherence of the incident ions, affects the constriction of the plasma and the transition between the HCVA modes. [ABSTRACT FROM AUTHOR]

Analyzing the timing properties of asynchronous systems is essential for characterizing their performance and power. Previous work on timing showed that such systems under and-causality and fixed delay exhibit periodicity properties. We give a different graph-based rigorous proof of the exact timing behavior of more general classes of such systems, and conclude their exact periodicity property, where each of the signal transition will occur with the same period after finite occurrences. We established our results under weaker assumption about system connectivity/topology, and this paper provides the theoretical foundation, for the exact periodicity property to be applied and exploited in circuits containing a combination of synchronous and asynchronous components. We provide simulation-based results for several typical asynchronous circuit topologies to quantify this time period in practical circuits. We also provide an extension of our analysis and methods to the case of bounded delay systems. A key result that is a consequence of our analysis is that asynchronous circuits can be integrated with synchronous logic via a metastability-free interface, thereby eliminating the high-overhead synchronizers when an asynchronous circuit is fully surrounded by synchronous logic. [ABSTRACT FROM PUBLISHER]

Recently, several papers on preventive maintenance (PM) have shown that segregation of PM’s can be beneficial when it comes to improving factory performance. However, these were limited to either cases of equal PM segregation and/or without consideration of other factors and operating conditions such as incurred setup or the number of tools in the toolset. In this paper, we extend previous work in this area in two major respects. First, we consider the more realistic case of PM segregation into equal or unequal portions and second, we evaluate the impact of PM segregation under various operating conditions via simulation. Our simulation experiments provide insight and guidelines for practitioners in planning the PM activity such that the overall performance is improved. [ABSTRACT FROM AUTHOR]

This paper develops a merging procedure for functional test sequences that achieves test compaction for a pool of functional test sequences by reducing the number of sequences in the pool. The procedure has the following new features: 1) in contrast to existing selection procedures, the merging procedure described in this paper increases the fault coverage of test sequences in the pool, thus enhancing the ability to reduce the number of sequences and 2) in contrast to existing procedures that concatenate or merge test sequences, the procedure described in this paper does not increase the lengths of the sequences it merges. The procedure is based on the concept of restoration of test vectors. In the context of test sequence merging, restoration consists of copying test vectors from a test sequence Tj into a test sequence Ti in order to allow Ti to detect faults that Tj detects. The merging procedure focuses on the removal of one test sequence Tj at a time by restoring test vectors from Tj into other sequences, allowing them to detect the faults that Tj detects. Experimental results for benchmark circuits demonstrate that the procedure reduces the number of sequences in a pool significantly. [ABSTRACT FROM PUBLISHER]

This paper presents a compact analytical I – V model for short-channel double-gate transition metal dichalcogenide filed-effect transistors in the subthreshold region. A closed-form expression is proposed for the characteristic length in the scale length approach, which is based on physical device parameters. It is then used to find the channel potential and drain current in the subthreshold region. This model is verified with the numerical results of a nonequilibrium Green’s function (NEGF) simulator. There is good agreement between the results of the proposed model and the numerical NEGF simulations in the subthreshold region, while it captures the effects of the device’s physical parameters. [ABSTRACT FROM PUBLISHER]

This paper considers the co-design technique of quantization and event-driven control for reducing the negative influences of network on the system performance of networked control systems (NCSs). Event-driven strategy aims at reducing the frequency of transmission, while signal quantization reduces the amounts of data for each transmission. By combining these two techniques, this paper establishes the quantized event-driven control approaches for both the fixed and relative event threshold cases. The system stability and the existence of the minimum interevent interval (MIEI) are analyzed. Finally, the validity of the proposed approaches is illustrated by the numerical simulations. [ABSTRACT FROM AUTHOR]

In this paper, a self-adaptive protection system is proposed for adjusting the time dial (TD) of reclosers found in electrical power distribution systems (EPDSs). The self-adjustment is carried out in both phase and ground protection. The methodology considers the fuses along the feeder to obtain the fuse-saving philosophy. This feature allows less interference on the protection system already implemented by the electrical power distribution utilities. This methodology also allows using other frameworks, such as the estimation of the fault distance. The software used for computer modeling and simulation was PSCAD™/EMTDC™. The flexibility provided by the method, which allows the incorporation of new logic and changes in decision-making, resulted in an adaptive method with a good performance against different locations, types, and fault impedance. It also resulted in better coordination between the protection devices (PDs). The results compared with well-coordinated conventional protection have shown significant performance gain with the adaptive system. [ABSTRACT FROM AUTHOR]

The tip size of metal protrusions is an important factor affecting corona discharge, since it influences the electric filed, the ionization range and strength around the protrusion defect. Most existing studies on the influence of protrusion tip size on corona discharge are implemented by experimental methods. However, these studies are difficult to obtain the microphysical process of charged particles, which is related to the generation of current pulses and electromagnetic (EM) waves. In this paper, a hydrodynamic simulation model is proposed to study the effect of protrusion tip size on the microphysical process and current pulses of negative corona discharge. A mapping relationship between microscopic behaviors of charged particles and current pulses is established by this simulation method. Based on the comparison of microphysical quantities, the effect of defect tip size on the detailed parameters of current pulses is clearly explained. It shows that with the increase of tip size under a constant voltage, all the five parameters of current pluses increase. The rising time is related to the effective ionization coefficient, while the falling time is dependent on the velocities of positive and negative ions. The experiment and simulation results coincide in current waveforms and all five parameters. [ABSTRACT FROM AUTHOR]

The dynamic interaction of vehicles/bridges is an important part of the research field of the Electromagnet Suspension (EMS) maglev train. However, multiple factors affect the dynamics of the coupling system, which increases the complexity of the vehicle-bridge coupling system, and makes it difficult to analyze. Herein, combining the advantages of theoretical derivation and numerical calculation, a fast and accurate analysis method of maglev vehicle and bridge system is proposed to analyze the influence of bridge and controller on the dynamics of the maglev system. This work is directed to the Changsha maglev express line, in which the mathematical equations for the vehicle- bridge system is presented. Then the influence of the parameter on the system is analyzed. Finally, the vibration experimental test system is set up, and the vibration test of the maglev vehicle bridge is tested by the test scheme, and the experimental results data are given. The test results of vibration acceleration are in good agreement with the calculation results of the proposed method, which verifies the accuracy of the model and the analysis method. Therefore, the research in this paper can provide theoretical guidance for Maglev engineering, and the analysis method in this paper can also be used in the study of other vehicles, such as the high-speed maglev train. [ABSTRACT FROM AUTHOR]

The paper presents the results of experimental registrations and numerical simulations of the transient overvoltages caused by single phase intermittent arc earth fault in 35 kV network with isolated neutral. Experimental laboratory investigation is performed in order to implement appropriate arc fault model for arcs with low and discontinuous current. Single phase to earth arc fault is created in field in 35 kV network. Numerical model of the system is created in EMTP-ATP software. Overvoltage waveshapes and overvoltage factors are calculated and compared to measured values. Good agreement between the measured and calculated results is achieved. [ABSTRACT FROM AUTHOR]

Coded caching can significantly reduce the communication bandwidth requirement for satisfying users’ demands by utilizing the multicasting gain among multiple users. Most existing works assume that the users follow the prescriptions for content placement made by the system. However, users may prefer to decide what files to cache. To address this issue, we consider a network consisting of a file server connected through a shared link to $\boldsymbol {K}$ users, each equipped with a cache which has been already filled arbitrarily. Given an arbitrary content placement, the goal is to find a delivery strategy for the server that minimizes the load of the shared link. In this paper, we focus on a specific class of coded multicasting delivery schemes known as the “clique cover delivery scheme.” We first formulate the optimal clique cover delivery problem as a combinatorial optimization problem. Using a connection with the weighted set cover problem, we propose an approximation algorithm and show that it provides an approximation ratio of $(\textbf {1} + \log \boldsymbol {K})$ , while the approximation ratio for the existing coded delivery schemes is linear in $\boldsymbol {K}$. Numerical simulations show that our proposed algorithm provides a considerable bandwidth reduction over the existing coded delivery schemes for almost all content placement schemes. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the realization of synchronized spread spectrum code division multiple access (synchronized SS-CDMA) for the quasi-zenith satellite system (QZSS) safety confirmation system during major disasters. The QZSS is expected to provide a highly accurate positioning service and allow two-way communication, which includes the terminal location and short messages. The proposed synchronized SS-CDMA scheme realizes direct access from mobile terminals to the satellite and the simultaneous transmission of many users using SS codes with a large spreading factor. All terminals synchronize their own clock and frequency with those of the global navigation satellite system (GNSS). In this scheme, maintaining orthogonality among users in both the time and frequency domains is the most important problem. In this paper, for the consideration of mobile use, the effect of residual timing jitter and frequency offset in a fading environment is evaluated by computer simulation. As a result, acceptable timing and frequency errors for terminals are clarified in order for the system to be viable using the GNSS. [ABSTRACT FROM AUTHOR]

Silicon carbide (4H-SiC) devices experiencing avalanche conditions can reach temperatures above 1500 K. Simulation of impact ionization in devices should, therefore, include models valid up to such high temperatures. However, calibrations of impact ionization coefficients are available only up to 580 K, and simulations of switching show deviations from measurements at higher temperatures. In this paper, a more accurate model based on the underlying physics of high temperature and anisotropic avalanche generation is proposed. This model enables calibrations performed at room temperature along the ${c}$ -axis to be more precisely extrapolated to any temperature of interest in 2-D device simulations. The model provides an excellent fit to the measurements of breakdown voltages during unclamped inductive switching tests of power MOSFETs, enabling a more accurate prediction of ruggedness. The more comprehensive physics included in the model makes it also applicable to other wide bandgap semiconductors such as GaN, diamond, and Ga2O3, which also exhibit a high critical electric field. [ABSTRACT FROM AUTHOR]