Search

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]

A single-stage high-frequency resonant ac/ac converter converts the ac-line input voltage into the high-frequency sinusoidal output voltage, which consists of two power conversion units, i.e., a power factor correction (PFC) unit and a high-frequency resonant dc/ac unit, and it can be used to derive a modular multichannel constant current LED driver. By adopting a totem-pole bridgeless PFC boost rectifier to reduce conduction losses, a single-stage bridgeless high-frequency resonant ac/ac converter is proposed in this paper. The operating principle is described, and the performance analysis is presented in detail. Moreover, the quantitative parameter design method of the main circuit is presented, which is suitable for other single-stage ac input converters, such as a single-stage PFC rectifier. Finally, a 130-W prototype has been built and tested to verify the correction of related theoretical analysis and parameter design. [ABSTRACT FROM AUTHOR]

Insulated-gate bipolar transistor (IGBT) modules and dc-link capacitors are important parts in the majority of power electronic converters which contribute to cost, size, and failure rate on a considerable scale. This paper presents an online condition monitoring method for both IGBT modules and dc-link capacitors of power converters based on short-circuit current of an IGBT module, which is a good condition indicator according to the theory analysis. The failure prediction of dc-Link capacitor is realized by equivalent series resistance, which can be calculated by short-circuit current and a step voltage, and the bond wires fatigue can also be identified by the short-circuit current. The proposed method is capable for detecting small changes in the failure indicators of IGBT modules and electrolytic capacitors, and its effectiveness is validated by a confirmatory experiment. The novelty of the proposed method is that the degradations of IGBT modules and capacitors can be identified simultaneously, and has the merits of low cost and circuit simplicity [ABSTRACT FROM PUBLISHER]

Potential defects inside an insulated gate bipolar transistor (IGBT) module can be seen as precursors of being about to wear out, and are important for health monitoring of the IGBT module which is used to enhance reliability. A method for detecting defects in the IGBT module by identifying dynamic changes of the gate current is presented in this paper. It is based on the fact that parasitic elements inside the IGBT module are affected by local damage induced by aging over time, and subsequently, these influences are easily distinguished by dynamic changes of the gate current. The proposed prognostic approach is based on relevance vector machine framework, which can give accurate predictions and allow operators to observe unhealthy IGBT modules inside a power converter, and then take appropriate measures timely to avoid breakdown. The parasitic elements involved in the gate circuit are extracted, and their contributions to dynamic changes of the gate current are also discussed. Finally, a confirmatory experiment is carried out, and the correctness of the proposed method is verified. [ABSTRACT FROM AUTHOR]

This paper presents a reconfigurable structure dc–dc converter with wide output range and constant peak power (RS-WOCP). This converter is an extension of the traditional isolated dc–dc converter with two output channels by adding an active switch and two diodes. Theoretical analysis indicates that the proposed RS-WOCP converter is able to smoothly reconfigure the output channels in parallel or series to realize wide output voltage range. With this approach, the output voltage is shared equally in the series operating mode and so is the output current in the parallel operating mode. Therefore, the power rating of devices is significantly reduced and the output rectifiers and filters can distribute power losses and thermal stresses. Operating principle, control strategy, modeling, and stability analysis are illustrated in this paper. An experimental prototype of a 200-W DSP-based RS-WOCP converter was built. The experimental results have verified the steady-state performance and fast dynamic response in the whole output voltage range. Comparisons with two close relatives of wide output converters show that the proposed RS-WOCP converter is advantageous for wide output range constant peak power applications. [ABSTRACT FROM AUTHOR]