Search

This article is focused on the design of a high-voltage (800 V) bidirectional boost converter with high efficiency at medium-low power levels. Triangular current mode (TCM) enhances the efficiency of the converter at low power, thanks to soft-switching operation, but it requires variable switching frequency and large current ripple through the inductor. The former can be implemented by using silicon carbide (SiC) mosfets and the latter can be minimized by using interleaved modules. At low power, TCM requires high switching frequency, a minimum negative inductor current, and a minimum deadtime to obtain zero voltage switching. These values vary for different input/output voltage ratios and must be properly selected to reduce deadtime losses, normally neglected in the literature since it is assumed that they have low impact. However, it can be relevant at high frequencies (especially for devices with high reverse conduction voltage drop, such as SiC mosfets). In this article, deadtime losses are included in the proposed losses models and the selection of optimum values of deadtime and minimum inductor current to minimize these deadtime losses are analytically evaluated and experimentally validated. [ABSTRACT FROM AUTHOR]

A converter intended to be used for the interconnection of battery-based energy storage systems with the cells of a multilevel converter is addressed in this paper. High efficiency at light and medium loads is important in these applications and it can be achieved using soft switching techniques. Two control techniques with fixed and variable switching frequency are proposed and compared. The use of silicon carbide (SiC) mosfets provides a higher attainable switching frequency, which is especially interesting in variable frequency control techniques, allowing the operation at high voltages and high switching frequencies, with high efficiencies over a wide power range. A synchronous boost DC/DC converter rated for 400 to 800 V and 10 kW is designed and developed with SiC mosfets obtaining efficiencies higher than 97% from 100% to 3.5% of full load using a variable switching frequency (up to 200 kHz) control. Significant efficiency improvement is achieved at medium and light loads. [ABSTRACT FROM PUBLISHER]

Quasi-square wave mode with zero voltage switching (QSW-ZVS) is an operation mode in which the switching losses can be minimized. However, a large inductance current ripple is needed in this mode, which limits the maximum attainable power of the topology. A possible way to increase the power managed by a QSW-ZVS mode converter is to use a modular converter. An input parallel output parallel (IPOP) arrangement, in which the current can be shared among the modules, can increase the total power proportionally to the number of modules. This paper addresses two main proposals. The first one is a master–slave technique to extend the QSW-ZVS mode to an IPOP modular converter, achieving an interleaved solution which minimizes the total input current ripple and assures the current balance among the modules. The second one is a comparison of four different control techniques applied to the IPOP modular converter to improve the overall efficiency at light to medium load: balanced master–slave technique, master–slave with phase-shedding, asymmetrical master–slave, and burst mode (or hysteretic control). These four strategies are theoretically analyzed, experimentally validated and compared using a 150–400 V 2 kW modular IPOP prototype made up of four synchronous boost converter operating in QSW-ZVS mode. [ABSTRACT FROM PUBLISHER]

This paper describes a modular architecture based on the dual-active bridge (DAB) converter in input-series–output-parallel (ISOP) connection. This work is focused on the input voltage sharing to ensure a proper operation of each module by means of an active control of input and output voltages. A small-signal model of the modular architecture is proposed and a decoupled control loops’ scheme is used to implement the control strategy. An experimental setup has been built in order to validate the model of the DAB converter in ISOP connection and the proposed control strategy, taking different operating conditions and constructive parameter values into account. [ABSTRACT FROM AUTHOR]

This paper addresses the performance of the bidirectional dual active bridge (DAB) converter. One of the advantages of the DAB is the possibility to achieve the zero-voltage switching (ZVS) operation in all the switches of this converter. However, the ZVS operation range can be lost for light loads, especially if high voltage is required in at least one of the DAB ports and the phase-shift control is used to regulate the power processed by the converter. Theoretically simple averaged and small-signal models are presented for the DAB converter. Using the study presented in this paper, the boundaries of the ZVS operation can be easily evaluated. The proposed models and analysis of the ZVS boundaries allow the proposal and evaluation of two different design strategies with different purposes: on the one hand, increasing the ZVS operation range and, on the other, improving efficiency at full load. Moreover, some techniques are presented for increasing the ZVS operation range and improving the efficiency of the DAB at full load (both using phase-shift control) employing the aforementioned analysis to obtain certain design criteria and conclusions. Finally, the proposed models, design strategies, and techniques to improve the performance of the DAB are experimentally tested using a 1-kW prototype with input and output voltages of 48 and 400 V, respectively. [ABSTRACT FROM AUTHOR]