Search

The continuous monitoring of soil water content is commonly carried out using low-frequency capacitance sensors that require a site-specific calibration to relate sensor readings to apparent dielectric bulk permittivity (Kb) and soil water content (θ). In fine-textured soils, the conversion of Kb to θ is still challenging due to temperature effects on the bound water fraction associated with clay mineral surfaces, which is disregarded in factory calibrations. Here, a multi-point calibration approach accounts for temperature effects on two soils with medium to high clay content. A calibration strategy was developed using repacked soil samples in which the Kb-θ relationship was determined for temperature (T) steps from 10 to 40 °C. This approach was tested using the GS3 and TEROS-12 sensors (METER Group, Inc. Pullman, WA, USA; formerly Decagon Devices). Kb is influenced by T in both soils with contrasting T-Kb relationships. The measured data were fitted using a linear function θ = a K b + b with temperature-dependent coefficients a and b. The slope, a(T), and intercept, b(T), of the loam soil were different from the ones of the clay soil. The consideration of a temperature correction resulted in low RMSE values, ranging from 0.007 to 0.033 cm3 cm−3, which were lower than the RMSE values obtained from factory calibration (0.046 to 0.11 cm3 cm−3). However, each experiment was replicated only twice using two different sensors. Sensor-to-sensor variability effects were thus ignored in this study and will be systematically investigated in a future study. Finally, the applicability of the proposed calibration method was tested at two experimental sites. The spatial-average θ from a network of GS3 sensors based on the new calibration fairly agreed with the independent area-wide θ from the Cosmic Ray Neutron Sensor (CRNS). This study provided a temperature-corrected calibration to increase the accuracy of commercial sensors, especially under dry conditions, at two experimental sites. [ABSTRACT FROM AUTHOR]

Soil moisture profile sensors (SMPSs) have a high potential for climate-smart agriculture due to their easy handling and ability to perform simultaneous measurements at different depths. To date, an accurate and easy-to-use method for the evaluation of long SMPSs is not available. In this study, we developed laboratory and field experiments to evaluate three different SMPSs (SoilVUE10, Drill&Drop, and SMT500) in terms of measurement accuracy, sensor-to-sensor variability, and temperature stability. The laboratory experiment features a temperature-controlled lysimeter to evaluate intra-sensor variability and temperature stability of SMPSs. The field experiment features a water level-controlled sandbox and reference TDR measurements to evaluate the soil water measurement accuracy of the SMPS. In both experiments, a well-characterized fine sand was used as measurement medium to ensure homogeneous dielectric properties in the measurement domain of the sensors. The laboratory experiments with the lysimeter showed that the Drill&Drop sensor has the highest temperature sensitivity with a decrease of 0.014 m3 m−3 per 10 °C, but at the same time showed the lowest intra- and inter-sensor variability. The field experiment with the sandbox showed that all three SMPSs have a similar performance (average RMSE ≈ 0.023 m3 m−3) with higher uncertainties at intermediate soil moisture contents. The presented combination of laboratory and field tests were found to be well suited to evaluate the performance of SMPSs and will be used to test additional SMPSs in the future. [ABSTRACT FROM AUTHOR]

Understanding the impact of land use/land cover (LULC) change on hydrology is the key to sustainable water resource management. In this study, we used the Soil and Water Assessment Tool (SWAT) to evaluate the impact of LULC change on the runoff in the Rur basin, Germany. The SWAT model was calibrated against the observed data of stream flow and runoff at three sites (Stah, Linnich, and Monschau) between 2000 and 2010 and validated between 2011 and 2015. The performance of the hydrological model was assessed by using statistical parameters such as the coefficient of determination (R2), p-value, r-value, and percentage bias (PBAIS). Our analysis reveals that the average R2 values for model calibration and validation were 0.68 and 0.67 (n = 3), respectively. The impacts of three change scenarios on stream runoff were assessed by replacing the partial forest with urban settlements, agricultural land, and grasslands compared to the 2006 LULC map. The SWAT model captured, overall, the spatio-temporal patterns and effects of LULC change on the stream runoffs despite the heterogeneous runoff responses related to the variable impacts of the different LULC. The results show that LULC change from deciduous forest to urban settlements, agricultural land, or grasslands increased the overall basin runoff by 43%, 14%, and 4%, respectively. [ABSTRACT FROM AUTHOR]

Due to their unique characteristics, cosmic-ray neutron sensors (CRNSs) have potential in monitoring and informing irrigation management, and thus optimising the use of water resources in agriculture. However, practical methods to monitor small, irrigated fields with CRNSs are currently not available and the challenges of targeting areas smaller than the CRNS sensing volume are mostly unaddressed. In this study, CRNSs are used to continuously monitor soil moisture (SM) dynamics in two irrigated apple orchards (Agia, Greece) of ~1.2 ha. The CRNS-derived SM was compared to a reference SM obtained by weighting a dense sensor network. In the 2021 irrigation period, CRNSs could only capture the timing of irrigation events, and an ad hoc calibration resulted in improvements only in the hours before irrigation (RMSE between 0.020 and 0.035). In 2022, a correction based on neutron transport simulations, and on SM measurements from a non-irrigated location, was tested. In the nearby irrigated field, the proposed correction improved the CRNS-derived SM (from 0.052 to 0.031 RMSE) and, most importantly, allowed for monitoring the magnitude of SM dynamics that are due to irrigation. The results are a step forward in using CRNSs as a decision support system in irrigation management. [ABSTRACT FROM AUTHOR]

To ensure the good chemical status of surface water across Europe, it is necessary to increase research on the comprehensive impact of land use and land cover changes, i.e., deforestation, on the natural environment. For this reason, we used data from 9-year environmental monitoring in the Wüstebach experimental catchment of the TERENO (Terrestrial Environmental Observatories) network to determine the impact of partial deforestation on solute fluxes and stream water ionic composition. In 2013, a partial deforestation experiment was conducted in the study area using a cut-to-length logging method. To this end, two headwater catchments were compared: one partially deforested (22% of the catchment area) and one untreated control catchment. The concentrations of ions in stream water, groundwater, and precipitation were analyzed: Ca2+, Mg2+, Na+, K+, Al3+, Fetot, Mn2+, NO3−, SO4−, and Cl−. Most of the ions (Na+, Ca2+, Mg2+, Cl−, and SO4−) showed decreasing trends in concentrations after deforestation, indicating a dilution effect in stream water due to the reduction of the supply of solutes with precipitation in the open deforested area. The fluxes of these ions decreased by 5–7% in the first year after deforestation, although the stream runoff increased by 5%. In the second year, the decrease in ion fluxes was greater, from 6% to 24%. This finding confirms that only limited soil erosion occurred after the deforestation because the soil was well protected during logging works by covering harvester lanes with branches. Only K+ and NO3− ions showed increasing trends in both concentrations and fluxes in the partially deforested catchment in the first two to three years after deforestation. Spruce die-offs, common in Europe, may decrease the concentration and fluxes of base cations in surface water in a nutrient-limited environment. However, the simultaneous planting of young broad-leaved trees with post-harvesting regrowth could create a nutrient sink that protects the catchment area from nutrient depletion. [ABSTRACT FROM AUTHOR]

In recent years, wireless sensor network (WSN) technology has emerged as an important technique for wireless sensing of soil moisture from the field to the catchment scale. This review paper presents the current status of wireless sensor network (WSN) technology for distributed, near real-time sensing of soil moisture to investigate seasonal and event dynamics of soil moisture patterns. It is also discussed how WSN measurements of soil measurements contribute to the validation and downscaling of satellite data and non-invasive geophysical instruments as well as the validation of distributed hydrological models. Finally, future perspectives for WSN measurements of soil moisture are highlighted, which includes the improved integration of real-time WSN measurements with other information sources using the latest wireless communication techniques and cyberinfrastructures. [ABSTRACT FROM AUTHOR]

Cosmic ray neutron sensors (CRNS) are increasingly used to determine field-scale soil moisture (SM). Uncertainty of the CRNS-derived soil moisture strongly depends on the CRNS count rate subject to Poisson distribution. State-of-the-art CRNS signal processing averages neutron counts over many hours, thereby accounting for soil moisture temporal dynamics at the daily but not sub-daily time scale. This study demonstrates CRNS signal processing methods to improve the temporal accuracy of the signal in order to observe sub-daily changes in soil moisture and improve the signal-to-noise ratio overall. In particular, this study investigates the effectiveness of the Moving Average (MA), Median filter (MF), Savitzky–Golay (SG) filter, and Kalman filter (KF) to reduce neutron count error while ensuring that the temporal SM dynamics are as good as possible. The study uses synthetic data from four stations for measuring forest ecosystem–atmosphere relations in Africa (Gorigo) and Europe (SMEAR II (Station for Measuring Forest Ecosystem–Atmosphere Relations), Rollesbroich, and Conde) with different soil properties, land cover and climate. The results showed that smaller window sizes (12 h) for MA, MF and SG captured sharp changes closely. Longer window sizes were more beneficial in the case of moderate soil moisture variations during long time periods. For MA, MF and SG, optimal window sizes were identified and varied by count rate and climate, i.e., estimated temporal soil moisture dynamics by providing a compromise between monitoring sharp changes and reducing the effects of outliers. The optimal window for these filters and the Kalman filter always outperformed the standard procedure of simple 24-h averaging. The Kalman filter showed its highest robustness in uncertainty reduction at three different locations, and it maintained relevant sharp changes in the neutron counts without the need to identify the optimal window size. Importantly, standard corrections of CRNS before filtering improved soil moisture accuracy for all filters. We anticipate the improved signal-to-noise ratio to benefit CRNS applications such as detection of rain events at sub-daily resolution, provision of SM at the exact time of a satellite overpass, and irrigation applications. [ABSTRACT FROM AUTHOR]

Tree water use is a key variable in forest eco-hydrological studies and is often monitored by sap flow measurements. Upscaling these point measurements to the stand or catchment level, however, is still challenging. Due to the spatio-temporal heterogeneity of stand structure and soil water supply, extensive measuring campaigns are needed to determine stand water use from sap flow measurements alone. Therefore, many researchers apply water balance models to estimate stand transpiration. To account for the effects of limited soil water supply on stand transpiration, models commonly refer to plant water stress functions, which have rarely been parameterized for forest trees. The aim of this study was to parameterize the Feddes water stress model for Norway spruce (Picea abies [L.] Karst.). After successful calibration and validation of the soil hydrological model HYDRUS-1D, we combined root-zone water potential simulations with a new plant water stress factor derived from sap flow measurements at two plots of contrasting soil moisture regimes. By calibrating HYDRUS-1D against our sap flow data, we determined the critical limits of soil water supply. Drought stress reduced the transpiration activity of mature Norway spruce at root-zone pressure heads <-4100 cm, while aeration stress was not observed. Using the recalibrated Feddes parameters in HYDRUS-1D also improved our water balance simulations. We conclude that the consideration of sap flow information in soil hydrological modeling is a promising way towards more realistic water balance simulations in forest ecosystems. [ABSTRACT FROM AUTHOR]

Several studies currently strive to improve the spatial resolution of coarse scale high temporal resolution global soil moisture products of SMOS, SMAP, and ASCAT. Soil texture heterogeneity is known to be one of the main sources of soil moisture spatial variability. With the recent development of high resolution maps of basic soil properties such as soil texture and bulk density, relevant information to estimate soil moisture variability within a satellite product grid cell is available. We use this information for the prediction of the sub-grid soil moisture variability for each SMOS, SMAP, and ASCAT grid cell. The approach is based on a method that predicts the soil moisture standard deviation as a function of the mean soil moisture based on soil texture information. It is a closed-form expression using stochastic analysis of 1D unsaturated gravitational flow in an infinitely long vertical profile based on the Mualem-van Genuchten model and first-order Taylor expansions. We provide a look-up table that indicates the soil moisture standard deviation for any given soil moisture mean, available at https://doi.org/10.1594/PANGAEA.878889. The resulting data set helps identify adequate regions to validate coarse scale soil moisture products by providing a measure of representativeness of small-scale measurements for the coarse grid cell. Moreover, it contains important information for downscaling coarse soil moisture observations of the SMOS, SMAP, and ASCAT missions. In this study, we present a simple application of the estimated sub-grid soil moisture heterogeneity scaling down SMAP soil moisture to 1 km resolution. Validation results in the TERENO and REMEDHUS soil moisture monitoring networks in Germany and Spain, respectively, indicate a similar or slightly improved accuracy for downscaled and original SMAP soil moisture in the time domain for the year 2016, but with a much higher spatial resolution. [ABSTRACT FROM AUTHOR]

The scale difference between point in situ soil moisture measurements and low resolution satellite products limits the quality of any validation efforts in heterogeneous regions. Cosmic Ray Neutron Probes (CRNP) could be an option to fill the scale gap between both systems, as they provide area-average soil moisture within a 150-250 m radius footprint. In this study, we evaluate differences and similarities between CRNP observations, and surface soil moisture products from the Advanced Microwave Scanning Radiometer 2 (AMSR2), the METOP-A/B Advanced Scatterometer (ASCAT), the Soil Moisture Active and Passive (SMAP), the Soil Moisture and Ocean Salinity (SMOS), as well as simulations from the Global Land Data Assimilation System Version 2 (GLDAS2). Six CRNPs located on five continents have been selected as test sites: the Rur catchment in Germany, the COSMOS sites in Arizona and California (USA), and Kenya, one CosmOz site in New SouthWales (Australia), and a site in Karnataka (India). Standard validation scores as well as the Triple Collocation (TC) method identified SMAP to provide a high accuracy soil moisture product with low noise or uncertainties as compared to CRNPs. The potential of CRNPs for satellite soil moisture validation has been proven; however, biomass correction methods should be implemented to improve its application in regions with large vegetation dynamics. [ABSTRACT FROM AUTHOR]

Soil water content is a key variable for understanding and modelling ecohydrological processes. Low-cost electromagnetic sensors are increasingly being used to characterize the spatio-temporal dynamics of soil water content, despite the reduced accuracy of such sensors as compared to reference electromagnetic soil water content sensing methods such as time domain reflectometry. Here, we present an effective calibration method to improve the measurement accuracy of low-cost soil water content sensors taking the recently developed SMT100 sensor (Truebner GmbH, Neustadt, Germany) as an example. We calibrated the sensor output of more than 700 SMT100 sensors to permittivity using a standard procedure based on five reference media with a known apparent dielectric permittivity (1 < Ka < 34.8). Our results showed that a sensor-specific calibration improved the accuracy of the calibration compared to single "universal" calibration. The associated additional effort in calibrating each sensor individually is relaxed by a dedicated calibration setup that enables the calibration of large numbers of sensors in limited time while minimizing errors in the calibration process. [ABSTRACT FROM AUTHOR]

Parameterization of physically based and distributed hydrological models for mesoscale catchments remains challenging because the commonly available data base is insufficient for calibration. In this paper, we parameterize a mesoscale catchment for the distributed model HydroGeoSphere by transferring evapotranspiration parameters calibrated at a highly-equipped headwater catchment in addition to literature data. Based on this parameterization, the sensitivity of the mesoscale catchment to spatial variability in land use, potential evapotranspiration and precipitation and of the headwater catchment to mesoscale soil and land use data was conducted. Simulations of the mesoscale catchment with transferred parameters reproduced daily discharge dynamics and monthly evapotranspiration of grassland, deciduous and coniferous vegetation in a satisfactory manner. Precipitation was the most sensitive input data with respect to total runoff and peak flow rates, while simulated evapotranspiration components and patterns were most sensitive to spatially distributed land use parameterization. At the headwater catchment, coarse soil data resulted in a change in runoff generating processes based on the interplay between higher wetness prior to a rainfall event, enhanced groundwater level rise and accordingly, lower transpiration rates. Our results indicate that the direct transfer of parameters is a promising method to benefit highly equipped simulations of the headwater catchments. [ABSTRACT FROM AUTHOR]

This study aims to produce accurate predictions of the NO2 concentrations at a specific station of a monitoring network located in the Bay of Algeciras (Spain). Artificial neural networks (ANNs) and sequence-to-sequence long short-term memory networks (LSTMs) were used to create the forecasting models. Additionally, a new prediction method was proposed combining LSTMs using a rolling window scheme with a cross-validation procedure for time series (LSTM-CVT). Two different strategies were followed regarding the input variables: using NO2 from the station or employing NO2 and other pollutants data from any station of the network plus meteorological variables. The ANN and LSTM-CVT exogenous models used lagged datasets of different window sizes. Several feature ranking methods were used to select the top lagged variables and include them in the final exogenous datasets. Prediction horizons of t + 1, t + 4 and t + 8 were employed. The exogenous variables inclusion enhanced the model's performance, especially for t + 4 (ρ ≈ 0.68 to ρ ≈ 0.74) and t + 8 (ρ ≈ 0.59 to ρ ≈ 0.66). The proposed LSTM-CVT method delivered promising results as the best performing models per prediction horizon employed this new methodology. Additionally, per each parameter combination, it obtained lower error values than ANNs in 85% of the cases. [ABSTRACT FROM AUTHOR]

The European heat wave of 2018 was characterized by extraordinarily dry and hot spring and summer conditions in many central and northern European countries. The average temperatures from June to August 2018 were the second highest since 1881. Accordingly, many plants, especially trees, were pushed to their physiological limits. However, while the drought and heat response of field crops and younger trees have been well investigated in laboratory experiments, little is known regarding the drought and heat response of mature forest trees. In this study, we compared the response of a coniferous and a deciduous tree species, located in western and central–western Germany, to the extreme environmental conditions during the European heat wave of 2018. Combining classic dendroecological techniques (tree–ring analysis) with measurements of the intra–annual stem expansion (dendrometers) and tree water uptake (sap flow sensors), we found contrasting responses of spruce and oak trees. While spruce trees developed a narrow tree ring in 2018 combined with decreasing correlations of daily sap flow and dendrometer parameters to the climatic parameters, oak trees developed a ring with above–average tree–ring width combined with increasing correlations between the daily climatic parameters and the parameters derived from sap flow and the dendrometer sensors. In conclusion, spruce trees reacted to the 2018 heat wave with the early completion of their growth activities, whereas oaks appeared to intensify their activities based on the water content in their tree stems. [ABSTRACT FROM AUTHOR]

With the upcoming L-band Synthetic Aperture Radar (SAR) satellite mission Radar Observing System for Europe L-band SAR (ROSE-L) and its integration into existing C-band satellite missions such as Sentinel-1, multi-frequency SAR observations with high temporal and spatial resolution will become available. The SARSense campaign was conducted between June and August 2019 to investigate the potential for estimating soil and plant parameters at the agricultural test site in Selhausen (Germany). It included C- and L-band air- and space-borne observations accompanied by extensive in situ soil and plant sampling as well as unmanned aerial system (UAS) based multispectral and thermal infrared measurements. In this regard, we introduce a new publicly available SAR data set and present the first analysis of C- and L-band co- and cross-polarized backscattering signals regarding their sensitivity to soil and plant parameters. Results indicate that a multi-frequency approach is relevant to disentangle soil and plant contributions to the SAR signal and to identify specific scattering mechanisms associated with the characteristics of different crop type, especially for root crops and cereals. [ABSTRACT FROM AUTHOR]

Affordable and accurate weather monitoring systems are essential in low-income and developing countries and, more recently, are needed in small-scale research such as precision agriculture and urban climate studies. A variety of low-cost solutions are available on the market, but the use of non-standard technologies raises concerns for data quality. Research-grade all-in-one weather stations could present a reliable, cost effective solution while being robust and easy to use. This study evaluates the performance of the commercially available ATMOS41 all-in-one weather station. Three stations were deployed next to a high-performance reference station over a three-month period. The ATMOS41 stations showed good performance compared to the reference, and close agreement among the three stations for most standard weather variables. However, measured atmospheric pressure showed uncertainties >0.6 hPa and solar radiation was underestimated by 3%, which could be corrected with a locally obtained linear regression function. Furthermore, precipitation measurements showed considerable variability, with observed differences of ±7.5% compared to the reference gauge, which suggests relatively high susceptibility to wind-induced errors. Overall, the station is well suited for private user applications such as farming, while the use in research should consider the limitations of the station, especially regarding precise precipitation measurements. [ABSTRACT FROM AUTHOR]

Soils are the dominant source of atmospheric nitrous oxide (N2O), especially agricultural soils that experience both waterlogging and intensive nitrogen fertilization. However, soil heterogeneity and the irregular occurrence of hydrological events hamper the prediction of the temporal and spatial dynamics of N2O production and transport in soils. Because soil moisture influences soil redox potential, and as soil N cycling processes are redox-sensitive, redox potential measurements could help us to better understand and predict soil N cycling and N2O emissions. Despite its importance, only a few studies have investigated the control of redox potential on N2Oemission from soils in detail. This study aimed to partition the different microbial processes involved in N2O production (nitrification and denitrification) by using redox measurements combined with isotope analysis at natural abundance and 15N-enriched. To this end, we performed long-term laboratory lysimeter experiments to mimic common agricultural irrigation and fertilization procedures. In addition, we used isotope analysis to characterize the distribution and partitioning of N2O sources and explored the 15N-N2O site preference to further constrain N2O microbial processes. We found that irrigation, saturation, and drainage induced changes in soil redox potential, which were closely related to changes in N2O emission from the soil as well as to changes in the vertical concentration profiles of dissolved N2O, nitrate (NO3−) and ammonium (NH4+). The results showed that the redox potential could be used as an indicator for NH4+, NO3−, and N2O production and consumption processes along the soil profile. For example, after a longer saturation period of unfertilized soil, the NO3− concentration was linearly correlated with the average redox values at the different depths (R2 = 0.81). During the transition from saturation to drainage, but before fertilization, the soil showed an increase in N2O emissions, which originated mainly from nitrification as indicated by the isotopic signatures of N2O (δ15N bulk, δ18O and 15N-N2O site preference). After fertilization, N2O still mainly originated from nitrification at the beginning, also indicated by high redox potential and the increase of dissolved NO3−. Denitrification mainly occurred during the last saturation period, deduced from the simultaneous 15N isotope analysis of NO3− and N2O. Our findings suggest that redox potential measurements provide suitable information for improving the prediction of soil N2O emissions and the distribution of mineral N species along the soil profile under different hydrological and fertilization regimes. [ABSTRACT FROM AUTHOR]

The effects of land use change on the occurrence and frequency of preferential flow (fast water flow through a small fraction of the pore space) and piston flow (slower water flow through a large fraction of the pore space) are still not fully understood. In this study, we used a five year high resolution soil moisture monitoring dataset in combination with a response time analysis to identify factors that control preferential and piston flow before and after partial deforestation in a small headwater catchment. The sensor response times at 5, 20 and 50 cm depths were classified into one of four classes: (1) non-sequential preferential flow, (2) velocity based preferential flow, (3) sequential (piston) flow, and (4) no response. The results of this analysis showed that partial deforestation increased sequential flow occurrence and decreased the occurrence of no flow in the deforested area. Similar precipitation conditions (total precipitation) after deforestation caused more sequential flow in the deforested area, which was attributed to higher antecedent moisture conditions and the lack of interception. At the same time, an increase in preferential flow occurrence was also observed for events with identical total precipitation. However, as the events in the treatment period (after deforestation) generally had lower total, maximum, and mean precipitation, this effect was not observed in the overall occurrence of preferential flow. The results of this analysis demonstrate that the combination of a sensor response time analysis and a soil moisture dataset that includes pre- and post-deforestation conditions can offer new insights in preferential and sequential flow conditions after land use change. [ABSTRACT FROM AUTHOR]

Soil water content (SWC) monitoring is often used to optimize agricultural irrigation. Commonly, capacitance sensors are used for this task. However, the factory calibrations have been often criticized for their limited accuracy. The aim of this paper is to test the degree of improvement of various sensor- and soil-specific calibration options compared to factory calibrations by taking the 10HS sensor as an example. To this end, a two-step sensor calibration was carried out. In the first step, the sensor response was related to dielectric permittivity using calibration in media with well-defined permittivity. The second step involved the establishment of a site-specific relationship between permittivity and soil water content using undisturbed soil samples and time domain reflectometry (TDR) measurements. Our results showed that a model, which considered the mean porosity and a fitted dielectric permittivity of the solid phase for each soil and depth, provided the best fit between bulk permittivity and SWC. Most importantly, it was found that the two-step calibration approach (RMSE: 1.03 vol.%) provided more accurate SWC estimates compared to the factory calibration (RMSE: 5.33 vol.%). Finally, we used these calibrations on data from drip-irrigated almond and apple orchards and compared the factory calibration with our two-step calibration approach. [ABSTRACT FROM AUTHOR]