Search

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-level voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined with an equivalent representation of the electrical machine proved to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accurate results. This has been confirmed by comparing the results carried out from the simulations of a 110 kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling. [ABSTRACT FROM AUTHOR]

The degradation trend of photovoltaic modules depends on the technology, manufacturing techniques and climatic conditions of the site where they are installed. Longer useful life of the PV modules means that they will be able to produce much more energy than was used to build them; thus, extending the useful life of the modules is beneficial for the environment and increases the cost effectiveness of PVs. The problem of land use has prompted the development of agrivoltaic systems to exploit the same land both for the production of energy and for agriculture, and on water surfaces such as lakes and dams (floating PV). The exploitation of floating PV systems in onshore and offshore areas is currently under study. This constitutes an opportunity for which many factors must be taken into account; a fundamental aspect is the environmental impact, on which some recent studies have focused. Another aspect is the impact of the marine environment on PV system reliability and durability, due to the stress on operating conditions. The aim of this preliminary study is to evaluate the influence of the marine environment on the degradation trend of photovoltaic modules, based on existing models whose inputs are meteorological data from offshore locations. The results obtained from the application of a cumulative exposure model unexpectedly showed a lower degradation value in the offshore environment than on the mainland: −0.95% and −3% values of power decay, respectively. The absolute value of power decay in the onshore case is higher than the typical values because the used model has to be revised, as the empirical coefficients of the model have to be calculated according to the installation environment. The empirical coefficients used in the model were obtained in environmental conditions different from those under study. In the offshore case, the degradation estimated by the model does not take into account some environmental factors typical of the marine environment. Model adaptations calibrated with datasets of plants in environmental conditions similar to those analyzed would allow for greater accuracy in the results. [ABSTRACT FROM AUTHOR]

Considering the importance of lithium-ion (Li-ion) batteries and the attention that the study of their degradation deserves, this work provides a review of the most important battery state of health (SOH) estimation methods. The different approaches proposed in the literature were analyzed, highlighting theoretical aspects, strengths, weaknesses and performance indices. In particular, three main categories were identified: experimental methods that include electrochemical impedance spectroscopy (EIS) and incremental capacity analysis (ICA), model-based methods that exploit equivalent electric circuit models (ECMs) and aging models (AMs) and, finally, data-driven approaches ranging from neural networks (NNs) to support vector regression (SVR). This work aims to depict a complete picture of the available techniques for SOH estimation, comparing the results obtained for different engineering applications. [ABSTRACT FROM AUTHOR]

The traditional approach to calculate the active and reactive power in AC power systems requires the measurement of the phase shift between the voltage and current for the evaluation of the power factor. To do this, power analyzers can implement several methods. In principle, it is always necessary to identify specific points of waveforms (e.g., using a zero-crossing detection technique) and get their time shift. In a similar way, the frequency value must be evaluated in order to calculate the angular frequency. Unfortunately, this kind of common method exhibits some issues, such as the large sensitivity to noise. Moreover, inaccuracies in the evaluation of the power factor have a big impact on the final estimation of the electric power. This paper presents a simple but effective way to calculate the electric power, overcoming the need for a direct measurement of the phase shift and frequency. In particular, it is shown that the active power can be easily calculated as the difference between the peak value of the instantaneous power and apparent power. The reactive power and power factor are evaluated by exploiting the same quantities. The practical implementation of the proposed formulation in power analyzers guarantees several benefits without reducing accuracy. [ABSTRACT FROM AUTHOR]

A technique to improve the performance of grid-connected induction motors by exploiting an auxiliary winding set is proposed in this paper. This auxiliary winding features the same distribution of the main winding, although with a reduced number of turns and it is fed by an inverter a fraction of the power in comparison with the rated size of the induction motor. As shown in the paper, through the auxiliary winding, it is possible to set the machine power factor, increasing the efficiency of the power conversion system and mitigating speed oscillations due to torque disturbances. A mitigation of the grid current peaks due to motor start-up is obtainable. First, the proposed technique is theoretically introduced, then a feasibility assessment is accomplished by simulations. [ABSTRACT FROM AUTHOR]

A three-phase multi-level multi-input power converter topology is presented for grid-connected applications. It encompasses a three-phase transformer that is operated on the primary side in an open-end winding configuration. Thus, the primary winding is supplied on one side by a three-phase N-level neutral point clamped inverter and, on the other side, by an auxiliary two-level inverter. A key feature of the proposed approach is that the N-level inverter is able to perform independent management of N − 1 input power sources, thus avoiding the need for additional dc/dc power converters in hybrid multi-source systems. Moreover, it can manage an energy storage system connected to the dc-bus of the two-level inverter. The N-level inverter operates at a low switching frequency and can be equipped with very low on-state voltage drop Insulated-Gate Bipolar Transistor (IGBT) devices, while the auxiliary inverter is instead operated at low voltage according to a conventional high-frequency two-level Pulse Width Modulation (PWM) technique and can be equipped with very low on-state resistance Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET) devices. Simulations and experimental results confirm the effectiveness of the proposed approach and its good performance in terms of grid current harmonic content and overall efficiency. [ABSTRACT FROM AUTHOR]

This work presents a step-by-step procedure to estimate the lifetime of discrete SiC power MOSFETs equipping three-phase inverters of electric drives. The stress of each power device when it is subjected to thermal jumps from a few degrees up to about 80 °C was analyzed, starting from the computation of the average power losses and the commitment of the electric drive. A customizable mission profile was considered where, by accounting the working conditions of the drive, the corresponding average power losses and junction temperatures of the SiC MOSFETs composing the inverter can be computed. The tool exploits the Coffin–Manson theory, rainflow counting, and Miner's rule for the lifetime estimation of the semiconductor power devices. Different operating scenarios were investigated, underlying their impact on the lifetime of SiC MOSFETs devices. The lifetime estimation procedure was realized with the main goal of keeping limited computational efforts, while providing an effective evaluation of the thermal effects. The method enables us to set up any generic mission profile from the electric drive model. This gives us the possibility to compare several operating scenario of the drive and predict the worse operating conditions for power devices. Finally, although the lifetime estimation tool was applied to SiC power MOSFET devices for a general-purpose application, it can be extended to any type of power switch technology. [ABSTRACT FROM AUTHOR]

In this paper, a procedure to simulate an electronic power converter for control design and optimization purposes is proposed. For the addressed application, the converter uses SiC-MOSFET technology in bidirectional battery chargers composed of two power stages. The first stage consists of a single-phase AC/DC power factor correction synchronous rectifier. The following stage is a DC/DC dual active bridge. The converter has been modulated using a phase-shift technique which is able to manage bidirectional power flows. The development of a model-based simulation approach is essential to simplify the different design phases. Moreover, it is also important for the final validation of the control algorithm. A suitable tool consisting of a system-level simulation environment has been adopted. The tool is based on a block diagram design method accomplished using the Simulink toolbox in MATLAB™. [ABSTRACT FROM AUTHOR]

Distributed power converters represent a technical solution to improve the performance of large or utility-scale photovoltaic (PV) plants. Unfortunately, evaluation of the yield obtained in large PV fields by using distributed converters is a difficult task because of recurring partial unavailability, inaccuracy of power analyzers, operating constraints imposed by the Power Plant Controller and so on. To overcome such issues in real operating scenarios, a new modeling strategy has been introduced and validated in terms of computational complexity and accuracy. This approach is based on the state-space averaging technique which is applied to large PV plants with multiple conversion stages by performing some elaborations in order to get a final integrated model. The new modeling strategy has been tested in MatLab Simulink environment using data coming from a 300 MW PV plant located in Brazil representing the case study of this work. In this plant, one subfield is equipped with central inverters while another is with string inverters. The proposed model, whose accuracy is in the range from 2.2 to 2.7% with respect to the measured energy, effectively supports data analysis leading to a consistent performance assessment for the distributed conversion system. Final results highlight that string inverters ensure a gain of about 2% in terms of produced energy. [ABSTRACT FROM AUTHOR]