Search

Date fruit drying is a process that consumes a significant amount of energy due to the long duration required for drying. To better understand how moisture flows through the fruit during drying and to speed up this process, drying studies must be conducted in conjunction with mathematical modeling, energy analysis, and environmental economic analysis. In this study, twelve thin-layer mathematical models were designed utilizing experimental data for three different date fruit varieties (Sakkoti, Malkabii, and Gondaila) and two solar drying systems (automated solar dryer and open-air dryer). These models were then validated using statistical analysis. The drying period for the date fruit varieties varied between 9 and 10 days for the automated solar dryer and 14 to 15 days for open-air drying. The moisture diffusivity coefficient values, determined using Fick's second law of diffusion model, ranged from 7.14 × 10−12 m2/s to 2.17 × 10−11 m2/s. Among the twelve thin-layer mathematical models, we chose the best thin drying model based on a higher R2 and lower χ2 and RMSE. The Two-term and Modified Page III models delivered the best moisture ratio projections for date fruit dried in an open-air dryer. For date fruit dried in an automated solar dryer, the Two-term Exponential, Newton (Lewis), Approximation diffusion or Diffusion Method, and Two-term Exponential modeling provided the best moisture ratio projections. The energy and environmental study found that the particular amount of energy used varied from 17.936 to 22.746 kWh/kg, the energy payback time was 7.54 to 7.71 years, and the net CO2 mitigation throughout the lifespan ranged from 8.55 to 8.80 tons. Furthermore, economic research showed that the automated solar dryer's payback period would be 2.476 years. [ABSTRACT FROM AUTHOR]

An optimization technique, the Kepler optimizer (KO), is presented to enable permanent magnet synchronous wind generators (PMSWG) to run safely under faults and to accomplish the goal of low-carbon efficient power delivery and sustainable development. Utility companies are struggling, which is preventing the increase in wind penetration, in spite of the grid incorporation of PMSWG. One of these undisputed concerns is the grid-side voltage dip (VD) and swell (VS) at the PCC. Converters and DCL capacitors are particularly vulnerable to PCC nonstandard voltages because of an imbalance in the DCL input–output powers. Because of this, it is essential to provide WF-GCs to support grid operations, and developing techniques to realize FRTCs has become a crucial GC need. Installing an industrial braking chopper (BC) across the DCL is the suggested technique, due to its effectiveness and low price. In addition, a new KO-based control system for BC is used to enhance its effectiveness. Four situations were examined to assess and analyze the proposed control system regarding the transient response of the system. These situations exposed the investigated system to an irregular grid condition: without BC, with BC controlled by a hysteresis controller, and with BC controlled by KO-based PI (proposed) at (a) 100% VD, (b) 70% VD, (c) 30% VD, and (d) 20% VS. To verify the advantages and efficacy of the suggested control systems in the examined circumstances, MATLAB/SIMULINK was utilized. The simulation findings confirmed the feasibility of the suggested system as a whole and the control structures in suppression of all parameter transient changes, while also achieving FRTC. Furthermore, maintaining a steady DCL voltage serves as an advantage that would lengthen the electrical converters' lifetime and shorten the time that the unit would be turned off if it happens to fail. [ABSTRACT FROM AUTHOR]

To avert climate change, there has been a rise in the usage of green energy sources that are also beneficial to the environment. To generate sustainable energy in a financially and technically efficient manner, our research attempts to close the gaps. The potential of green sources like photovoltaic (PV) and biomass for a rural community southwest of Sohag Al Gadida City, Sohag, Egypt, is examined in this research considering its techno-economic (TE) and eco-friendly feasibility. The HOMER Pro v3.14 package is used as a scaling and optimization instrument, to calculate the price of the PV/biomass setup and the size and characteristics of its parts. This is to estimate the corresponding electrical production and reduce the total annual cost for the customer. The suggested system structure is validated through the presentation of simulation outcomes and evaluations utilizing MATLAB/SIMULINK R2022a. In addition, a TE-environmental investigation of the optimized PV/biomass structure is performed. The optimum structure is carefully chosen from the best four configurations using the demand predilection by analogy to the perfect technique based on the generation cost, operation cost, energy production, and renewable fraction. The results also indicate that using hybrid PV/biomass is an attractive choice with the initial capital cost (ICC: USD 8.144), net present cost (NPC: USD 11,026), a low cost of energy (LCOE: 0.184 USD/kWh), and the high renewable fraction (RF: 99.9%) of the system. The annual CO2 emission performance of a PV/biomass system is much better than that of the grid alone and PV/diesel. This method might be applied in rural areas in other developing countries. [ABSTRACT FROM AUTHOR]

The integration of clean energy sources (CESs) into modern power systems has been studied using various power converter topologies. The challenges of integrating various CESs are facilitated by the proper design of multi-port power converter (MPPC) architecture. In this study, a brand-new two-stage MPPC is suggested as a solution to the intermittent nature and slow response (SR) of CESs. The suggested system combines a DC\DC and a DC\AC converter and storage unit, and the suggested circuit additionally incorporates a number of CESs (PV\wind\fuel cell (FC)). This article discusses the power management and control technique for an integrated four-port MPPC that links three input ports (PV, wind, and FC), a bidirectional battery port, and an isolated output port. One of the recent optimization techniques (Harris Hawk's algorithm) is applied to optimize the system's controller gains. By intelligently combining CESs with complementary characteristics, the adverse effects of intermittency are significantly mitigated, leading to an overall enhancement in system resilience and efficiency. Furthermore, integrating CESs with storage units not only addresses SR challenges but also effectively combats intermittent energy supply. The proposed system exhibits improved dynamic capabilities, allowing it to efficiently distribute excess energy to the load or absorb surplus energy from external sources. This dual functionality not only optimizes system operation but also contributes to a reduction in system size and cost, concurrently enhancing reliability. A comprehensive investigation into operational principles and meticulous design considerations are provided, elucidating the intricate mechanics of the suggested MPPC system. Employing MATLAB/Simulink, the proposed architecture and its control mechanisms undergo rigorous evaluation, affirming the feasibility and efficacy of this innovative system. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems are crucial to the production of electricity for a newly established community in Egypt, especially in grid-tied systems. Power quality (PQ) issues appear as a result of PV connection with the power grid (PG). PQ problems cause the PG to experience faults and harmonics, which affect consumers. A series compensator dynamic voltage restorer (DVR) is the most affordable option for resolving the abovementioned PQ problems. To address PQ difficulties, this paper describes a grid-tied PV combined with a DVR that uses a rotating dq reference frame (dqRF) controller. The main goal of this study is to apply and construct an effective PI controller for a DVR to mitigate PQ problems. The artificial rabbits optimization (ARO) is used to obtain the best tune of the PI controller. The obtained results are compared with five optimization techniques (L-SHADE, CMAES, WOA, PSO, and GWO) to show its impact and effectiveness. Additionally, Lyapunov's function is used to analyze and evaluate the proposed controller stability. Also, a mathematical analysis of the investigated PV, boost converter, and rotating dqRF control is performed. Two fault test scenarios are examined to confirm the efficacy of the suggested control approach. The parameters' (voltage, current, and power) waveforms for the suggested system are improved, and the system is kept running continuously under fault periods, which improves the performance of the system. Moreover, the findings demonstrate that the presented design successfully keeps the voltage at the required level with low THD% values at the load side according to the IEEE standards and displays a clear enhancement in voltage waveforms. The MATLAB/SIMULINK software is used to confirm the proposed system's performance. [ABSTRACT FROM AUTHOR]

In recent modern power systems, the number of renewable energy systems (RESs) and nonlinear loads have become more prevalent. When these systems are connected to the electricity grid, they may face new difficulties and issues such as harmonics and non-standard voltage. The proposed study suggests the application of a whale optimization algorithm (WOA) based on a fractional-order proportional-integral controller (FOPIC) for unified power quality conditioner (UPQC) and STATCOM tools. These operate best with the help of their improved control system, to increase the system's reliability and fast dynamic response, and to decrease the total harmonic distortion (THD) for enhancing the power quality (PQ). In this article, three different configurations are studied and assessed, namely: (C1) WOA-based FOPIC for UPQC, (C2) WOA-based FOPIC for STATCOM, and (C3) system without FACTS, i.e., base case, to mitigate the mentioned drawbacks. C3 is also considered as a base case to highlight the main benefits of C1 and C2 in improving the PQ by reducing the %THD of the voltage and current system and improving the systems' voltage waveforms. With C2, voltage fluctuation is decreased by 98%, but it nearly disappears in C1 during normal conditions. Additionally, during the fault period, voltage distortion is reduced by 95% and 100% with C2 and C1, respectively. Furthermore, when comparing C1 to C2 and C3 under regular conditions, the percentage reduction in THD is remarkable. In addition, C1 eliminates the need for voltage sag, and harmonic and current harmonic detectors, and it helps to streamline the control approach and boost control precision. The modeling and simulation of the prepared system are performed by MATLAB/Simulink. Finally, it can be concluded that the acquired results are very interesting and helpful in the recovery to the steady state of wind systems and nonlinear loads, thereby increasing their grid connection capabilities. [ABSTRACT FROM AUTHOR]

Changes in climatic circumstances, as well as intermittency, which has a significant impact on the overall energy system output from renewable energy sources (RESs), require the development of control strategies for extracting the maximum power available from RESs. To accomplish this task, several techniques have been developed. An efficient maximum power point tracking (MPPT) technique should be utilized to guarantee that both wind-generation and PV-generation systems provide their full advantages. In this paper, a new MPPT approach with jellyfish search optimization (JSO) is developed; in addition, a unified power-quality conditioner (UPQC) is utilized to enhance the performance of the microgrid (MG) and to solve the power-quality issues for the sensitive load. The MG, which includes a photovoltaic (PV), a wind turbine, and a fuel cell battery, is examined and modeled for uniform and nonuniform wind speed and solar irradiance. A comparison between the developed algorithm and different maximum power tracking algorithms is presented. Additionally, four case studies are carried out to verify the effectiveness of the introduced UPQC in enhancing power-quality problems. The research outcome shows high performance from the developed algorithm when assessed with additional algorithms. MATLAB/Simulink software is utilized for the simulation of the wind, PV, and FC control systems. However, experiment validation tests are given under the same condition of PV irradiation to validate the simulation results. The experimental validation is executed by utilizing the PV module simulation model, threefold, 23 V/2A CO3208-1A with solar altitude emulator CO3208-1B board, and the results are compared to the simulation results. [ABSTRACT FROM AUTHOR]

Modern electrical power systems now require the spread of microgrids (MG), where they would be operating in either islanded mode or grid-connected mode. An inherent mismatch between loads and sources is introduced by changeable high renewable share in an islanded MG system with stochastic load demands. The system frequency is directly impacted by this mismatch, which can be alleviated by incorporating cutting-edge energy storage technologies and FACTS tools. The investigated islanded MG system components are wind farm, solar PV, Electric vehicles (EVs), loads, DSTATCOM, and diesel power generator. An aggregated EVs model is connected to the MG during uncertain periods of the generation of renewable energy (PV and wind) to support the performance of MGs. The ability to support ancillary services from the EVs is checked. DSTATCOM is used to provide voltage stability for the MG during congestion situations. The MG is studied in three scenarios: the first scenario MG without EVs and DSTATCOM, the second scenario MG without DSTATCOM, and the third scenario MG with all components. These scenarios are addressed to show the role of EVs and DSTATCOM, and the results in the third scenario are the best. The system voltage and frequency profile is the best in the last scenario and is entirely satisfactory and under the range of the IEEE standard. The obtained results show that both EVs and DSTATCOM are important units for improving the stability of modern power grids. The Matlab/Simulink program is considered for checking and validating the dynamic performance of the proposed configuration. [ABSTRACT FROM AUTHOR]

The synergetic control technique (SCT) has the solution for understanding the symmetry inherent in the non-linear properties of wind turbines (WTs); therefore, they achieve excellent performance and enhance the operation of the WT. Small-scale WTs are efficient and cost-effective; they are usually installed close to where the generated electricity is used. This technology is gaining popularity worldwide for off-grid electricity generation, such as in rural homes, farms, small factories, and commercial properties. To enhance the efficiency of the WT, it is vital to operate the WT at its maximum power. This work proposes an efficient and fast maximum power point tracking (MPPT) technique based on the SCT to eradicate the drawbacks of the conventional methods and enhance the operation of the WT at the MPP regardless of wind speed and load changes. The SCT has advantages, such as robustness, simplified design, fast response, no requirement for knowledge of WT characteristics, no need for wind sensors or intricate power electronics, and straightforward implementation. Furthermore, it improves speed convergence with minimal steady-state oscillations at the MPP. The investigated configuration involves a wind-driven permanent magnet synchronous generator (PMSG), uncontrolled rectifier, boost converter, and variable load. The two converters are used to integrate the PMSG with the load. Three scenarios (step changes in wind speed, stochastic changes in wind speed, and variable electrical load) are studied to assess the SCT. The results prove a high performance of the suggested MPPT control method for a fast convergence speed, boosted WT efficacy, low oscillation levels, and applicability under a variety of environmental situations. This work used the MATLAB/Simulink program and was then implemented on a dSPACE 1104 control board to assess the efficacy of the SCT. Furthermore, experimental validation on a 1 kW Darrieus-type WT driving a PMSG was performed. [ABSTRACT FROM AUTHOR]

Wind generators have attracted a lot of attention in the realm of renewable energy systems, but they are vulnerable to harsh environmental conditions and grid faults. The influence of the manta ray foraging optimizer (MRFO) on the dynamic performance of the two commonly used variable speed wind generators (VSWGs), called the permanent magnet synchronous generator (PMSG) and doubly-fed induction generator (DFIG), is investigated in this research article. The PMSG and DFIG were exposed to identical wind speed changes depending on their wind turbine characteristics, as well as a dangerous three-phase fault, to evaluate the durability of MRFO-based wind side controllers. To protect VSWGs from hazardous gusts and obtain the optimum power from incoming wind speeds, we utilized a pitch angle controller and optimal torque controller, respectively, in our study. During faults, the commonly utilized industrial approach (crowbar system) was exclusively employed to aid the studied VSWGs in achieving fault ride-through (FRT) capability and control of the DC link voltage. Furthermore, an MRFO-based PI controller was used to develop a crowbar system. The modeling of PMSG, DFIG, and MRFO was performed using the MATLAB/Simulink toolbox. We compared performances of PMSG and DFIG in reference tracking and resilience against changes in system parameters under regular and irregular circumstances. The effectiveness and reliability of the optimized controllers in mitigating the adverse impacts of faults and wind gusts were demonstrated by the simulation results. Without considering the exterior circuit of VSWGs or modifying the original architecture, MRFO-PI controllers in the presence of a crowbar system may help cost-effectively alleviate FRT concerns for both studied VSWGs. [ABSTRACT FROM AUTHOR]