Search

In many applications, interior permanent magnet synchronous machines (IPMSMs) with fractional slot concentrated windings (FSCWs) are considered promising candidates in terms of higher power density and efficiency. In addition, employing a multiphase stator winding improves the drive train availability and increases reliability. This study investigates the effect of applying stator shifting to five‐phase FSCW winding IPMSMs to suppress the effect of the slot harmonics by doubling the number of slots. In this case, the winding coil pitch will be two, which stands as a compromise between single‐tooth and distributed winding topologies. This highly improves the air gap flux distribution, significantly reduces both rotor core and magnet eddy current losses, and increases saliency ratio and reluctance torque component. Moreover, an improved performance under fault conditions, in terms of lower torque ripple, and core and magnet losses, adds to the main advantages of this technique. Various slot/pole combinations suitable for five‐phase machines are investigated. A full simulation case study based on two‐dimensional finite element analysis is applied to the 20‐slot/18‐pole stator with single‐tooth winding under both healthy and open‐circuit phase fault cases. [ABSTRACT FROM AUTHOR]

In electric drive applications that are based on high‐speed induction motors (IMs) with an extended speed range, stator winding pole‐changing is a possible technique to avoid oversizing the driving motor. The electronic pole changing employed in multiphase IMs has gained recent interest because it avoids physical winding reconfiguration. The effective number of poles of the air gap flux distribution can be electronically altered by simply changing the applied current sequence to a multiphase stator. The main problem associated with this technique is the significant increase in machine magnetising current with the increase in effective pole number when conventional multiphase distributed windings are employed. This study proposes a new fractional‐slot concentrated winding layout with a special stator connection suitable for pole‐amplitude modulated IMs that offers a 2:1 pole ratio while maintaining equal magnetising current for both winding pole pairs. Moreover, constant power operation can be achieved for a speed range of over 4 pu. The main concept is discussed and verified through simulations and experimentally. The machine mathematical model and the required vector space decomposition‐based controller are also presented. [ABSTRACT FROM AUTHOR]

In this study, a cost‐effective HVDC shunt tap with low‐number of relatively low‐voltage semiconductor devices and small‐sized passive components is proposed. The proposed architecture is based on employing three single‐phase half‐bridge Modular Multilevel Converters (MMCs), where the DC sides of MMCs are connected in series across the total DC‐link voltage. The MMCs are adopted instead of conventional Two‐Level Voltage Source Converters (2L‐VSCs) to avoid the complications of series connection of Insulated Gate Bipolar Transistors (IGBTs). The involved MMCs in the suggested architecture are operated with the conventional 2L modulation, which results in insignificant arm inductors and Sub‐Modules (SMs) capacitances (in range of µH and µF, respectively). This, in turn, affects positively the converter cost and footprint. Each arm of the involved MMCs can be considered as a high‐voltage valve of a 2L‐VSC. To maintain the balance of SMs capacitors, each arm of the involved (N + 1)‐level MMC has an extra SM (a balancing SM) to select N out of N + 1 SMs during the turn‐off condition. The operational concept, design, and assessment of the proposed architecture are presented in this study. Simulation results are provided for substantiation of the proposed concept. Finally, a scaled down single‐phase prototype is used for experimental validation. [ABSTRACT FROM AUTHOR]

This study proposes an isolated on‐board integrated battery charger using an interior permanent magnet (IPM) machine with a nine‐slot/eight‐pole combination or its multiples, and equipped with a non‐overlapped fractional slot concentrated winding. The proposed winding layout comprises three three‐phase winding sets that are connected in such a way as to provide six motor terminals. Hence, a six‐phase or two three‐phase converters will be required for propulsion. Under motoring mode, the machine can be effectively regarded as a six‐phase machine, which provides a high fault‐tolerant capability, and allows for a 'limp home' mode of operation. Additionally, all magneto motive force subharmonics are eliminated, which significantly reduces the induced rotor eddy current losses, when compared with a conventional three‐phase motor having the same slot/pole combination. In battery charging mode, the winding is reconfigured, so that the machine is considered as a three‐phase to six‐phase rotating transformer. A 40 kW IPM machine is designed and simulated under different modes of operation using two‐dimensional finite element analysis to validate the proposed concept. A small‐scale prototype machine is also used for experimental validation. [ABSTRACT FROM AUTHOR]

The half‐bridge modular multilevel converter (HB‐MMC) is one of the most promising topologies for high‐voltage direct current (HVDC) systems. Unlike full‐bridge MMC (FB‐MMC) and clamp double sub‐module MMC (CDSM‐MMC), HB‐MMCs are defenceless against DC side faults. Different types of DC circuit breakers (DC CBs) assisted with arrester banks/damping resistors such as solid‐state CB and hybrid DC CBs can be used to interrupt the DC fault current. Arrester banks are used to protect against overvoltage after interrupting the fault current and in turn to demagnetise the circuit inductors. The main disadvantage of the arresters is that they forcibly break apart when they are overloaded. In this study, an arrester‐less fault current limiter is proposed for HB‐MMC configuration, which provides an opposing voltage during the DC side fault. This is achieved by inserting external pre‐charged capacitors in the DC current path during the fault. The selection of these external capacitors, their suitable initial voltages, and their charging stations are also presented in this study. A comparison between the proposed scheme and the CDSM‐MMC has been held as well. The proposed protection scheme is assessed using a simulation study for a point‐to‐point nine‐level HB‐MMC‐based HVDC system. [ABSTRACT FROM AUTHOR]

Conventional modular multilevel converters (MMCs) are promising converters for high-voltage high-power applications. Unlike DC-AC conversion, DC-DC conversion of MMCs suffers from unbalanced capacitor voltages due to the energy drift problem. In this study, a new modular DC-DC converter is proposed, which consists of front-end half-bridge MMC with half-bridge submodules followed by full-bridge MMC with full-bridge submodules. The proposed modular multilevel DC-DC converter can be used effectively for connecting two different DC voltage levels in high-/medium-voltage DC grids. The proposed architecture provides successful DC-DC conversion with balanced capacitor voltages throughout the arm interchange concept. It also provides a high conversion ratio, bidirectional power flow, low losses, low current stresses, reduced number of submodules, and DC fault blocking capability. Detailed illustration, operational concept, and design of the proposed architecture with the arm interchange concept are presented. Simulation results for a high-voltage high-power DC-DC converter with the suggested approach are presented to demonstrate the system performance during different normal as well as abnormal operating conditions. Finally, a scaled-down prototype has been implemented for validation. The extracted simulation and experimental results elucidate the presented claims. [ABSTRACT FROM AUTHOR]

Conventional modular multilevel converters (MMCs) are promising converters for high‐voltage high‐power applications. Unlike DC–AC conversion, DC–DC conversion of MMCs suffers from unbalanced capacitor voltages due to the energy drift problem. In this study, a new modular DC–DC converter is proposed, which consists of front‐end half‐bridge MMC with half‐bridge submodules followed by full‐bridge MMC with full‐bridge submodules. The proposed modular multilevel DC–DC converter can be used effectively for connecting two different DC voltage levels in high‐/medium‐voltage DC grids. The proposed architecture provides successful DC–DC conversion with balanced capacitor voltages throughout the arm interchange concept. It also provides a high conversion ratio, bidirectional power flow, low losses, low current stresses, reduced number of submodules, and DC fault blocking capability. Detailed illustration, operational concept, and design of the proposed architecture with the arm interchange concept are presented. Simulation results for a high‐voltage high‐power DC–DC converter with the suggested approach are presented to demonstrate the system performance during different normal as well as abnormal operating conditions. Finally, a scaled‐down prototype has been implemented for validation. The extracted simulation and experimental results elucidate the presented claims. [ABSTRACT FROM AUTHOR]

Here, a new bi‐directional hybrid modular non‐isolated DC–DC converter is proposed where it consists of a boost converter (BC) fed from the high‐voltage (HV) side. At the BC output stage, a certain number of half bridge submodules (HB‐SMs) is connected across the BC switch. During the turn‐on period of BC switch, the HB‐SMs are connected sequentially to the low‐voltage (LV) side, which results in charging/discharging their capacitors from/into the LV side. While, during the turn‐off period, the LV side is bypassed and the HB‐SMs capacitors are connected in series across the BC output stage, which results in discharging/charging them into/from the HV side. The power flow is controlled in both directions by controlling the duty cycle. The proposed configuration provides self‐balancing operation thanks to the sequential connection of HB‐SMs capacitors, and it also provides the ability to operate with high conversion ratios. Illustration and analysis of the proposed converter and its closed‐loop controller are presented. A full design of the values and ratings of the involved components are presented. Simulation study for a 2.5 MW (25 kV/10 kV) DC–DC converter is presented. Finally, experimental results for a downscaled prototype are presented for validation. [ABSTRACT FROM AUTHOR]

In this study, a new transformerless wind energy conversion system to integrate high‐power multi‐phase permanent magnet wind generators to medium‐voltage local grids is presented. The proposed converter topology consists of multi‐half‐bridge modules with a high ac–direct current (dc) boosting capability. Each phase of an open winding multi‐phase generator is connected to the ac side of a half‐bridge module, whereas the dc sides of the half‐bridge modules are connected in series forming the high‐voltage dc‐link output. The proposed architecture facilitates the employment of semiconductor switches with a relatively low‐voltage rating, which equals the dc‐link voltage divided by the number of generator phases. A detailed analysis of the proposed architecture along with the required closed‐loop control is presented. The proposed architecture is simulated under different operating conditions using a typical 2 MW system, while the experimental validation is carried out using a low‐scale prototype converter. [ABSTRACT FROM AUTHOR]

This study proposes a new architecture of flywheel energy storage system (FESS) which can be implemented at generating unit (GU) level (e.g. wind turbine) or scaled up for application in grid‐side converter (GSC) stations of a multi‐terminal direct current (MTDC) system. The proposed architecture suppresses DC voltage leaps under grid faults, and performs power levelling duty at grid connection points. When implemented at GU level, the proposed FESS features a doubly‐fed induction machine (DFIM) – the flywheel machine – where its six stator winding terminals are connected in series between the grid and the GSC. The flywheel converter is of partial power rating, and is connected to the DFIM rotor. When employed at an MTDC GSC station, several submodules are connected to build an FESS station. The study proposes the control concept and the general topology of the FESS station. The performance parameters of the system are tested under normal and abnormal operating conditions. Results and analyses indicate smooth dynamic operation, the economic advantage and the improved fault ride‐through capability because of the proposed system. [ABSTRACT FROM AUTHOR]