Search

To resist large electromagnetic loads, the ITER correction coils (CCs) are protected by a 20-mm thickness 316LN austenitic stainless steel case. Due to the strict tolerance requirement of the case manufacture, tungsten inert gas (TIG) welding technology was used for subcase assembly welding, whereas laser beam welding (LBW) technology was applied to enclosure welding of the cases. The case shall be operated at 4.2 K and shall undergo considerably cyclic stress due to magnet electromagnetization as well as interaction with the toroidal field (TF) and poloidal field (PF). This article focuses on the assessment of the mechanical properties of the welding joints at cryogenic temperature. Results indicated that the values of the ultimate tensile strength of the TIG welding joint and the LBW welding joint were 1555 and 1522 MPa, respectively, which reach to 99.7 and 97.6% of that of the base material (BM). The elongation at the fracture of both the TIG and LBW weldments was larger than 35%. The plane strain fracture toughness KIc(J) of the TIG and the LBW weldments was 210 and 241 MPa·m1/2, respectively. The fractographic analysis indicated that the fracture surface was composed of fine equiaxed dimples, which indicated that both welding joints fractured in a ductile manner. The welding joints survived the minimum of 30 000 cycles fatigue test at stress level and load ratio specified by the ITER document. In addition, the fatigue crack growth rates of both welding joints were lower than that of the BM. All mechanical properties of both the welding joints satisfied the ITER specifications. [ABSTRACT FROM AUTHOR]

• The two-dimensional temperature field of the tensile process was investigated based on Digital Image Correlation (DIC) technology and cooling heat transfer model. • The reconstructed temperature field is in good agreement with the temperature rise in the tensile process. • The observed trend of increased martensite production is consistent with the simulated predictions. To better understand the tensile fracture behavior and temperature variation during the tension testing of the 316LN at cryogenic temperatures, a two-dimensional temperature field solution method is developed based on two-dimensional strain field measured by the digital image correlation technology combined with the Taylor Quinney coefficient model and the intrinsic model of strain-induced martensitic phase transformation. The method allows for visualization of the strain field and temperature variation of the 316LN austenitic stainless steel at cryogenic temperature. By numerical simulation, the localized temperature elevation of the 316LN is determined to be 13.3 K during the tensile test at 77 K, which is in good agreement with the experimental result of 10.2 K. This model reconstructed the two-dimensional temperature field variation throughout the entire tensile test, which is beneficial for facilitating the analysis of the mutual relation between the mechanical properties and microstructural evolution of the 316LN and other metastable austenitic stainless steels in cryogenic temperatures. [ABSTRACT FROM AUTHOR]

In this work, the microstructure evolution and magnetic properties of the 316LN austenitic stainless steels under high-cycle-fatigue loading at liquid helium temperature (4.2 K) were assessed by using the X-ray diffractometer (XRD), electron microscopy and magnetic measurements. The microstructure was composed of a single face-centered cubic (FCC) phase, and the high local misorientation was found near the grain boundaries. Observations through the high-resolution transmission electron microscopy reveals that the deformation was dominated by the dislocation and stacking faults. The magnetic susceptibility varies slightly after cyclic loading test at 4.2 K. [Display omitted] [ABSTRACT FROM AUTHOR]

• The 0.2% proof stress and ultimate tensile strength at 4.2 K for 35% pre-strained specimens increased respectively around 86% and 18% compared to those of the as-received material. • The elongation at fracture at both RT and 4.2 K decreased for the pre-strained 316LN SS compared to those of the as-received material. • The pre-strained 316LN SS fractured at 4.2 K exhibits a ductile fracture mode. In the present work, influences of room temperature tensile pre-strain on cryogenic tensile properties of 316LN austenitic stainless steel (SS) were investigated. The tensile properties of the 316LN SS with various tensile pre-straining amounts of 15%, 25% and 35% were measured at both room temperature (RT) and liquid helium temperature (4.2 K). Results indicated that both 0.2% proof strength (R p0.2) and ultimate tensile strength (R m) at both RT and 4.2 K of the pre-strained 316LN SS significantly increased compared to those of the as-received material. The R p0.2 and R m at 4.2 K for 35% pre-strained specimens increased around 86% and 18%, respectively, compared to those of the as-received material. However, the elongation at fracture (A) at both RT and 4.2 K decreased for the pre-strained 316LN SS compared to those of the as-received material. The fractured morphologies of the pre-strained 316LN SS were investigated by means of scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Dimples in the surface fractured at both RT and 4.2 K of the as-received and pre-strained 316LN exhibited a ductile fracture mode. Moreover, fractographic results indicated that the pre-strain treatment considerably decreased the ductility at both RT and 4.2 K. TEM analyses revealed that pre-strain treatment at RT led to dislocation accumulation and stress-induced martensite phase occurred at 4.2 K, which interpreted the cryogenic tensile properties of the pre-strained 316LN SS. [ABSTRACT FROM AUTHOR]