Search

This article presents a novel approach to the analysis of heat release in a hydrogen-fueled internal combustion spark-ignition engine with exhaust gas recirculation (EGR). It also discusses aspects of thermodynamic analysis common to modeling and empirical analysis. This new approach concerns a novel method of calculating the specific heat ratio (cp/cv) and takes into account the reduction in the number of moles during combustion, which is characteristic of hydrogen combustion. This reduction in the number of moles was designated as a molar contraction. This is particularly crucial when calculating the average temperature during combustion. Subsequently, the outcomes of experimental tests, including the heat-release rate, the initial combustion phase (denoted CA0-10) and the main combustion phase (CA10-90), are presented. Furthermore, the impact of exhaust gas recirculation on the combustion process in the engine is also discussed. The efficacy of the proposed measures was validated by analyzing the heat-release rate and calculating the mean combustion temperature in the engine. The application of EGR in the range 0-40% resulted in a notable prolongation of both the initial and main combustion phases, which consequently influenced the mean combustion temperature. [ABSTRACT FROM AUTHOR]

Hydrogen as potential engine fuel can appear either as a single gas or as a component in processing gases e.g. syngas, hythane and coke gas. The research in this paper investigates impact of combustible mixture dilution on abnormal combustion called knock in the reciprocating internal combustion engine. Dilution can be realized by either exhaust gas recirculation (EGR) or making the combustible mixture lean. Novelty of this work is a new metrics defined as dilution ratio, which makes it possible to compare knock reduction caused by either EGR or leaning the air-gas mixture to the engine. Two gaseous fuels were investigated: hydrogen and coke gas with 65% hydrogen. Conclusion based on the proposed dilution ratio states that, for hydrogen as the fuel, applying EGR is more effective in knock reduction than making the mixture lean. It was found that EGR strategy in the hydrogen fueled engine can reduce knock intensity from initial 40 kPa–20 kPa, whereas by leaning the mixture to the same dilution ratio, the knock is reduced to approximately 28 kPa. With respect to coke gas, it is proved that both EGR and lean mixtures influence on knock reduction at the same strength. • Combustible mixture dilution impact on combustion knock intensity. • Dilution ratio as a metrics for both exhaust gas recirculation and lambda. • Engine knock reduced more effectively by applying exhaust gases recirculation. • The correlation between dilution ratio and knock intensity is almost linear. [ABSTRACT FROM AUTHOR]

The main objective of this study was to examine impact of hydrogen addition to the compression ignition engine fueled with either rapeseed methyl ester (RME) or 7% RME blended diesel fuel (RME7) on combustion phases and ignition delay as well as smoke and exhaust toxic emissions. Literature review shows in general, hydrogen in those cases is used in small amounts below lower flammability limits. Novelty of this work is in applying hydrogen at amounts up to 44% by energy as secondary fuel to the compression ignition engine. Results from experiments show that increase of hydrogen into the engine makes ignition delay shortened that also affects main combustion phase. In all tests the trends of exhaust HC and CO toxic emissions vs. hydrogen addition were negative. The trend of smokiness decreased steadily with increase of hydrogen. Amounts of hydrogen addition by energy share were limited to nearly 35% due to combustion knock occurring at nominal load. • Hydrogen as secondary fuel for the diesel engine. • Main combustion phase and ignition delay shorten with hydrogen addition. • Indicated thermal efficiency stays not changed remarkably. • Hydrogen addition decreases smokiness, unburnt hydrocarbons and carbon monoxide. • Knock occurred at hydrogen addition over 35% by energy. [ABSTRACT FROM AUTHOR]

The paper presents results from investigation on a new type of fuel which can be implemented for the both automotive and power industry. The proposed fuel is of a completely renewable origin based on ethanol and glycerol at the ratio of 3:1 (75% and 25%), respectively. Hence, it does not contribute to unsustainable CO 2 emissions to the atmosphere. The analysis of combusting the ethanol-glycerol blend in the spark-ignited reciprocating engine was focused on engine performance, combustion thermodynamics, and toxicity content in the exhaust gases. The analysis was conducted as a comparative analysis for gasoline and ethanol, which were treated as reference fuels. The toxic emissions of CO, NOx, and unburnt hydrocarbons (UHC) did not differ remarkably from the gasoline emissions tests. The engine performance expressed by the indicated mean effective pressure deteriorated less than 3%. It was found that the ethanol-glycerol blend at the ratio of 3:1 (75/25%) can be directly applied as a substitute fuel for either gasoline or ethanol in internal combustion engines in the automotive and power industry. [Display omitted] • Investigation of ethanol-glycerol blend (3,1) for the internal combustion engine. • The engine performance (IMEP) deteriorated less than 3%. • Exhaust emissions of the blend are at similar level of gasoline 95 emissions tests. • Ethanol-glycerol blend can be applied as fuel for the spark-ignited engine. • Glycerol blended ethanol - considered an economic and energy-effective technology. [ABSTRACT FROM AUTHOR]

Abstract: Combustion knock is abnormal combustion taking place in an internal combustion spark ignited engine. It might be particularly observed in the engine at the end of combustion when the air–fuel mixture residue can be self-ignited due to exceeding auto-ignition temperature of this mixture. However, while hydrogen is combusted the knock can also occur as a result of non-auto-ignited combustion events. Investigation on knock, presented in the manuscript, was conducted in a hydrogen fueled spark ignited single cylinder engine with variable compression ratio. To express in numbers intensity of the combustion knock the in-cylinder pressure pulsations were used as a credible metrics. On the basis of analysis of these pulsations the hydrogen knock was distinguished as light and heavy one depending on its origin. The light knock is generated by combustion instabilities, which are a source for generating pressure waves inside the engine cylinder. The heavy knock results from hydrogen auto-ignition at the end of combustion. Its intensity is several times higher in comparison to the light knock. These observations were additionally confirmed by analysis of heat release rate. Finally, the light and the heavy knock were characterized by average amplitude of the pulsations from the entire test series of hundreds and several thousands kPa, respectively. [Copyright &y& Elsevier]

Abstract: The paper presents results and discussion on syngas combustion in a spark ignited internal combustion engine driving a power generator (16kW/1500rpm). The syngas applied as the engine fuel is produced by gasifying municipal sewage sludge. Unlike fermentation biogas, the syngas obtained from sewage sludge gasification is found a fuel, which generates several difficulties (non-stable combustion, misfiring events) while burning in the SI engine. The analysis of cycle-by-cycle engine run shows that the engine working on syngas features will run unsteadily due to the occurrence of misfiring events caused by the relatively low calorific value of the syngas. Thus, combustion of such a syngas in the SI IC engine can generate malfunctions. Therefore, the syngas was enriched with methane at various ratios starting from 0% up to 60% by volume. The impact of methane addition on the engine performance and exhaust emission was also presented in the paper. As investigated, 40% methane enrichment in the syngas was found sufficient amounts to obtain satisfactory engine run. Thus, in practice, the syngas from sewage sludge gasification is a troublesome fuel, but can satisfactorily be applied to the SI engine when enriched with natural gas or biogas. [Copyright &y& Elsevier]

Abstract: The paper mainly focuses on applying the two-stage combustion system with a pre-chamber into the stationary internal combustion spark ignited engine. It especially concentrates on applying throttle less operation at partial load and reduction of the NO x emission. Considerations conducted in the paper are based on the in-cylinder combustion progress analysis. Additionally, analysis of tailpipe toxic emission, with particular focus on the NO x formation in the engine equipped with the pre-chamber, is also performed. The paper presents both results of 3-D combustion modeling in the SI engine and results conducted on a test SI engine. The 3-D modeling was performed in the KIVA-3V code. Next, results from modeling were compared with results obtained from tests. Finally, satisfactory good consistency between modeled and experimental courses of both pressure, temperature and NO x were obtained. Thus, the engine model with the proposed two-stage combustion system properly simulates engine working conditions on the test bed. Results from both analyses confirmed that the two-stage combustion system significantly shortens combustion duration of an ultra lean gasoline–air mixture and contributes to reduction in NO x . [Copyright &y& Elsevier]

The paper presents results from an investigation focused on toxicity content in the exhaust gases emitted by an internal combustion compression ignition engine fueled with glycerol-ethanol blends at ratio of 50/50% by volume. The innovative issue of this engine is the application of two high pressure injectors for injecting both glycerol-ethanol blend and diesel pilot fuel at high pressure (over 200 MPa). As known, glycerol is considered a byproduct from biodiesel production technologies, hence its cost is relatively low compared to other renewable alternative fuels which can be applied as fuels to the reciprocating piston engines. It was found that the toxic components UHC, NOx and CO were below the maximum allowed limits. Both NOx and smoke emissions were strongly reduced with increasing glycerol-ethanol fraction in the fuel. Summarizing, a fueling strategy such as that proposed in this paper makes it possible to effectively and environmentally friendly combust crude glycerol in compression ignition engines working in a heat and power cogeneration unit. Exhaust gas emission tests conducted in this case confirmed the usability of this technology to be implemented into practice. [ABSTRACT FROM AUTHOR]