Search

Polyacrylonitrile and polyheteroarylenes, such as polybenzimidazole (PBI) and a polymer of intrinsic microporosity (PIM-1), have been employed to prepare nanoporous electrospun carbon nanofiber (CNF)-based materials for high-temperature proton-exchange (or polymer-electrolyte) membrane (HT-PEM) fuel cells. The nanoporous CNF mats are obtained by Nanospider (needle-free) electrospinning method from polymer solution followed by pyrolysis at 1500 °C to form nanoporous electrospun polymer nanofiber self-supporting mats with micropores (D < 2 nm) and mesopores (D 2–50 nm). The nanoporous CNF samples are extensively characterized by N2 and CO2 adsorption applying the BET, BJH, Dubinin–Radushkevich (DR), NLDFT, and GCMC methods, CO2 uptake, Raman spectroscopy, elemental analysis, electrical conductivity, electron microscopy, and XPS. The role of the polymer precursor on the obtained values of specific surface area (SSA) and volume for micro- and mesopores is presented and discussed. The PBI-based CNF material reaches a micropore SSA of 919 m2 g–1 and CO2 uptake of 4.0 mmol g–1 derived from CO2 adsorption (273 K) data, and a micropore SSA of 873 m2 g–1 according to the t-method derived from N2 adsorption data. Close values confirm higher accessibility of micropores compared with the case of PIM-based CNF, where the micropore SSA values derived from CO2 and N2 adsorption data are different and indicate the partial inaccessibility of micropores for low-temperature nitrogen adsorption (77 K). Platinum-decorated CNF mats are successfully tested as electrodes for HT-PEM fuel cells, showing the feasibility of using the mats as cathodes; nevertheless, further optimization is required. For CNF anodes, the HT-PEM fuel cell performance reaches 0.69 V at 0.2 A cm–2 and 0.53 W cm–2 at 1.4 A cm–2 which permits the use of the Pt/CNF mats as anodes. [ABSTRACT FROM AUTHOR]

The efficient use of renewable energy sources requires development of new electrocatalytic materials for electrochemical energy storage systems, particularly fuel cells. To increase durability of high temperature polymer electrolyte fuel cell (HT-PEMFC), Pt/carbon black based catalysts should be replaced by more durable ones, for example Pt/carbon nanofibers (CNF). Here, we report for the first time the quantitative ascorbic acid assisted deposition of Pt onto electrospun polyacrylonitrile-based CNF composite materials. The effect of their subsequent post-treatment at various temperatures (250 and 500 °C) and media (vacuum or argon-hydrogen mixture) on the Pt/C catalyst morphology is investigated. All obtained samples are thoroughly studied by high resolution electron microscopy, and Pt electrochemically active specific surface area was evaluated by cyclic voltammetry. [ABSTRACT FROM AUTHOR]

Different polyheteroarylenes, such as m-polybenzimidazole, polyphenylene oxide, polymer of intrinsic microporosity (PIM-1) and poly(N-phenylene-benzimidazole) were electrospun to obtain self-supporting polymer nanofiber mats. The mats after heat treatment, which contains stabilization in air at 250-350 °C and pyrolysis at 900-1000 °C under vacuum, convert into carbon nanofiber paper, a material which is suitable for Pt nanoparticle deposition. The possibility of usage of the obtained carbonized nanocomposites as entire gas diffusion electrodes for high temperature polymer electrolyte membrane fuel cell is shown. [ABSTRACT FROM AUTHOR]

Electrospinning of polyacrylonitrile/DMF dopes containing salts of nickel, cobalt, zirconium, cerium, gadolinium, and samarium, makes it possible to obtain precursor nanofiber mats which can be subsequently converted into carbon nanofiber (CNF) composites by pyrolysis at 1000–1200 °C. Inorganic additives were found to be uniformly distributed in CNFs. Metal states were investigated by transmission electron microscopy and X-ray photoelectron spectroscopy (XPS). According to XPS in CNF/Zr/Ni/Gd composites pyrolyzed at 1000 °C, nickel exists as Ni0 and as Ni2+, gadolinium as Gd3+, and zirconium as Zr4+. If CNF/Zr/Ni/Gd is pyrolyzed at 1200 °C, nickel exists only as Ni0. For CNF/Sm/Co composite, samarium is in Sm3+ form when cobalt is not found on a surface. For CNF/Zr/Ni/Ce composite, cerium exists both as Ce4+ and as Ce3+. Composite CNF mats were platinized and tested as cathodes in high-temperature polymer electrolyte membrane fuel cell (HT-PEMFC). Such approach allows to introduce Pt–M and Pt–MOx into CNF, which are more durable compared to carbon black under HT-PEMFC operation. For CNF/Zr/Ni/Gd composite cathode, higher performance in the HT-PEMFC at I >1.2 A cm-2 is achieved due to elimination of mass transfer losses in gas-diffusion electrode compared to commercial Celtec®P1000. [ABSTRACT FROM AUTHOR]