Search

The automobile industry uses magnesium for load-bearing components due to its low density, durability, and ductility. This study investigated a nanocomposite containing Nb2O5 (3 and 6 wt%) nanoparticles as reinforcement with AZ31 magnesium alloy made by stir casting. A severe plastic deformation was conducted on the cast samples via equal-channel angular pressing (ECAP) after homogenization at 410 °C for 24 h and aging at 200 °C for 10 h. The microstructural distributions and mechanical properties of the magnesium metal matrix composites (MMCs) reinforced with Nb2O5 nanoparticles were investigated via ECAP. With the increase in the number of ECAP passes, the grain sizes became uniform, and the size of secondary phases reduced in the pure Nb2O5/AZ31 MMC. The grain size decreased remarkably after the ECAP process from 31.95 µm to 18.41µm due to the dynamic recrystallization during plastic deformation. The mechanical properties of hardness, ultimate tensile strength, and elongation effectively improved after each ECAP pass. The maximum values achieved for the Nb2O5/AZ31 composite subjected to ECAP were 64.12 ± 12 HV, 151.2 MPa, and 52.71%. [ABSTRACT FROM AUTHOR]

The process engineering of Mg alloys is nevertheless compromised due to their relatively poor mechanical properties. To address some of these difficulties, metal-matrix composites (MMCs) of Mg-alloys have been investigated for sometime. In the present work, small amounts (up to 1 wt%) of WS 2 nanotubes are mixed with Mg-alloy (AZ31) using melt-stirring process above 700 °C. The new MMC nanocomposites exhibit much superior mechanical properties vis a vis the pristine alloy. Metallographic investigation demonstrates that the average grain size has been reduced in inverse proportion to the added amounts of nanotubes up to 1 wt%. Physical considerations suggest that the main mechanism responsible for the reinforcement effect lies in the mismatch between the thermal expansion coefficients of the metal and the nanotubes. This mismatch induced large density of dislocations in the grain boundaries in the vicinity of the nanotube-matrix interface, which obstruct the crack propagation. [ABSTRACT FROM AUTHOR]

Abstract: The effects of Mn substitution for Mg on the microstructure, mechanical properties, and corrosion behavior of Mg69−xZn27Ca4Mnx (x=0, 0.5 and 1at.%) alloys were investigated using X-ray diffraction, compressive tests, electrochemical treatments, and immersion tests, respectively. Microstructural observations showed that the Mg69Zn27Ca4 alloy was mainly amorphous. The addition of Mn decreases the glass-forming ability, which results in a decreased strength from 545MPa to 364MPa. However, this strength is still suitable for implant application. Polarization and immersion tests in the simulated body fluid at 37°C revealed that the Mn-doped Mg–Zn–Ca alloys have significantly higher corrosion resistance than traditional ZK60 and pure Mg alloys. Cytotoxicity test showed that cell viabilities of osteoblasts cultured with Mn-doped Mg–Zn–Ca alloys extracts were higher than that of pure Mg. Mg68.5Zn27Ca4Mn0.5 exhibits the highest bio-corrosion resistance, biocompatibility and has desirable mechanical properties, which could suggest to be used as biomedical materials in the future. [Copyright &y& Elsevier]

Abstract: Mg69Zn27Ca4 with a spot of Fe particle-reinforced alloys was synthesized by Cu-mold injection casting using industrial raw materials. The microstructure, mechanical properties and corrosion resistance of these Mg-based alloys were studied by X-ray diffraction, differential scanning calorimeter, compressive testing and electrochemical measurements, respectively. The Mg69Zn27Ca4 alloy can be controlled to become fully amorphous using the industrial raw materials. With Fe particle addition, ductile α-Mg and Mg–Zn dendrites were embedded in the amorphous matrix, which enhanced the compressive strength and fracture strain. The Mg69Zn27Ca4 glassy alloy and Mg69Zn27Ca4/Fe alloy remarkably improved the corrosion resistance in 3.5wt% NaCl solution compared with AZ31 and pure Mg. Therefore, Mg69Zn27Ca4 and Mg69Zn27Ca4/Fe alloys have high potential as engineering materials. [Copyright &y& Elsevier]