Search

Gallium oxide (Ga2O3), with an ultrawide bandgap corresponding to the deep ultraviolet (DUV) range, has attracted significant attention in optical filter‐free photodetectors. In practical terms, DUV photodetectors employed in extreme conditions, for example, flame detection and space exploration, face the challenges of performance degradation caused by high/low‐temperature transformation. Here, DUV photodetectors are tailored with high durability and stability by one‐step‐grown β‐Ga2O3 films via pulsed laser deposition. A high‐oxygen‐pressure scheme effectively addresses the issue of film‐free deposition at specifically high temperatures, facilitating the formation of polycrystalline high‐resistivity β‐Ga2O3 films. As a result, the devices exhibit outstanding performance, including a low dark current (4.4 pA @30 V), high photoresponsivity (147.36 A W−1), and fast response time (3.1/22.6 ms). Additionally, the photoresponse performance shows minimal degradation at high temperatures up to 300 °C and even improves at low temperatures down to −100 °C, ranking it among the most robust DUV photodetectors. The mechanism of photoresponse, involving the exciton formation, bandgap evolution, carrier‐phonon scatter, etc., is also elucidated in a wide temperature range. This work provides an efficient solution for developing robust Ga2O3 DUV photodetectors with excellent performance for extreme‐condition applications. [ABSTRACT FROM AUTHOR]

With the rapid development of modern communication technology, it has become a core problem in the field of communication to find new ways to effectively modulate signals and to classify and recognize the results of automatic modulation. To further improve the communication quality and system processing efficiency, this study combines two different neural network algorithms to optimize the traditional signal automatic modulation classification method. In this paper, the basic technology involved in the communication process, including automatic signal modulation technology and signal classification technology, is discussed. Then, combining parallel convolution and simple cyclic unit network, three different connection paths of automatic signal modulation classification model are constructed. The performance test results show that the classification model can achieve a stable training and verification state when the two networks are connected. After 20 and 29 iterations, the loss values are 0.13 and 0.18, respectively. In addition, when the signal-to-noise ratio (SNR) is 25dB, the classification accuracy of parallel convolutional neural network and simple cyclic unit network model is as high as 0.99. Finally, the classification models of parallel convolutional neural networks and simple cyclic unit networks have stable correct classification probabilities when Doppler shift conditions are introduced as interference in practical application environment. In summary, the neural network fusion classification model designed can significantly improve the shortcomings of traditional automatic modulation classification methods, and further improve the classification accuracy of modulated signals. [ABSTRACT FROM AUTHOR]

The work presented an electrochemical anode method with different electrolyte concentrations and heat posttreatment to control the stoichiometry and structure of Cu2−xS electrocatalysts. X‐ray diffraction, X‐ray photoelectron spectroscopy, and scanning electron microscopy were employed to characterize the composition and morphology, whereas the electrocatalytic activity was evaluated by linear scanning voltammetry and electrochemical impedance spectroscopy. The results showed that the electrochemical method successfully synthesized thin flake‐shaped Cu7S4, which exhibited optimal performance at the electrolyte concentration of 0.45 mol L1 with maximum turnover frequency of 0.786 s−1, maximum mass activity of 0.539 A g−1, minimum charge transfer resistance of 0.156 Ω cm−2, and minimum overpotential of 154 mV at a current density of 10 mA cm−2. In the Cu7S4 structure, Cu2+ and S2− were coordinated in a CuS4 tetrahedral structure, whereas Cu+ and S2− were coordinated in a CuS3 triangular structure. Heat posttreatment could change the stoichiometry from 1.75 to 1.8 and improve the electrochemical performance. In the Cu9S5 structure, the CuS3 triangular structure had disappeared. Under the same conditions, the overvoltage was only 128 mV. [ABSTRACT FROM AUTHOR]

A numerical simulation model of a natural ventilation greenhouse is helpful for improving the production and quality of greenhouse crops in tropical areas. Field experiments show that the mean coefficient of variation of indoor light intensity in four seasons was lower than 10.0%. The highest indoor temperature reached 39.3 °C during summer, while the average indoor temperature ranged from 24 °C to 26 °C in the other three seasons. The average relative humidity in the greenhouse ranged from 76% to 87% annually, which was higher and more stable than that in the external environment. A three-dimensional steady-state numerical model of the greenhouse was established based on computational fluid dynamics. Under natural ventilation conditions, the maximum error between the simulated value and the measured value of the temperature in each measuring point was 5.90%. And the average relative error between the simulated and measured values was 3.0% in the range of 0.7−1.5 m of crop cultivation height. Finally, a numerical simulation of adding side windows and expanding the vents was carried out. The results show that these methods can homogenize the airflow distribution in the greenhouse and improve the utilization efficiency of natural ventilation without more mechanical system operations. [ABSTRACT FROM AUTHOR]

The growth of Cu2O crystal planes was be controlled by adding surfactant to the NaCl solution in this manuscript. The structure and composition of the synthesized Cu2O particles were characterized by X‑ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), and specific surface area test method (BET). The photocatalytic activities were evaluated by degrading methyl orange (MO) solution under magnetic stirring. The results shown that the synthesized Cu2O particle was spherical self-assembly structure when the surfactant was CTAB, and behaved higher degradation performance. Under dark conditions, the adsorption efficiency of 100 mg L–1 MO solution reached 67.08% in the first 1 min by 0.33 g L–1 CTAB-Cu2O, and after 15 min, the adsorption degradation efficiency of MO had reached 99.17%. The maximum adsorption capacity of CTAB-Cu2O was 297.28 mg g–1. The adsorption kinetics obeyed pseudo-second-order kinetics and followed the Freundlich isotherm. [ABSTRACT FROM AUTHOR]

Comprehensive Summary: As the third generation new battery, the power conversion efficiency (PCE) of metal halide perovskite solar cells (PSCs) has increased from 3.8% in 2009 to 25.8% currently certified, which fully shows that they have great research value and development prospect. As one of the main components of high‐efficiency PSCs, hole transport materials (HTMs) play an important role in extracting and transporting holes and inhibiting charge recombination. However, commonly used HTMs require doping, and the hygroscopicity and corrosiveness of the dopants will destroy the stability of PSCs and hinder their commercialization. Therefore, it is of great significance to develop dopant‐free HTMs. In this review, the dopant‐free HTMs in recent six years are reviewed and summarized systematically, including organic small molecules, polymers and cross‐linkable materials. We focus on the design of the molecular cores and discuss their structure–property correlation, conductivity, and photovoltaic performance. Finally, how to design an ideal HTM is summarized. We hope that this review can provide reference for the development of low‐cost and dopant‐free HTMs to prepare efficient and stable PSCs. [ABSTRACT FROM AUTHOR]

The optimum phenylalanine (Phe) requirement for hybrid grouper (Epinephelusfuscoguttatus ♀ × Epinepheluslanceolatus ♂) juveniles was determined through an 8-week growth trial. A total of seven isoenergetic (340 kcal per 100 g of dry matter), isonitrogenous, and isolipidic diets were made, containing 8.2 (Phe 8.2), 9.2 (Phe 9.2), 10.1 (Phe 10.1), 11.2 (Phe 11.2), 13.3 (Phe 13.3), 15.2 (Phe 15.2), and 17.3 g/kg (Phe 17.3), respectively. Triplicate tanks of juvenile fish (about 16.7 g/fish) were fed each experimental diet twice daily until apparent satiation. The results indicated that different dietary Phe levels significantly influenced weight gain percentage (WG), feed efficiency (FE), protein efficiency ratio (PER), as well as, productive protein value (PPV). Fish fed Phe 8.2 had the lowest WG or PPV among all experimental treatments. Furthermore, the optimal dietary Phe level increased fold height, width, enterocyte, and microvillus height of fish. The Phe 10.1 group exhibited higher growth hormone (GH) expression in the pituitary compared to other groups. Expression of hepatic insulin-like growth factor-1 (IGF-1) and growth hormone receptor 1 (GHR1) displayed a similar pattern of variation to that of GH. The Phe 13.3 group had lower expression of S6 kinase 1 (S6K1) and target of rapamycin (TOR) than other groups. In addition, fish fed Phe 10.1 had lower levels of nuclear factor erythroid 2 (Nrf2) and heat shock protein 70 (HSP70) in the head kidney, and Cu/Zn-superoxide (Cu/ZnSOD) dismutases in the midgut compared to fish fed other Phe levels. Generally, optimal Phe content in the diet of hybrid grouper was estimated to be 12.7 g/kg of dry matter (27.3 g/kg of dietary protein), and at this level, the feed utilization, gut micromorphology, and immunity of fish were also elevated. [ABSTRACT FROM AUTHOR]

This study is aimed at evaluating the effects of dietary protein-to-energy ratios on the growth, immunological response, antioxidative capacity, liver and intestinal histology, and growth-related gene expression of hybrid yellow catfish (Pelteobagrus fulvidraco ♀ × Pelteobagrus vachelli ♂). Eight diets were formulated to form different protein/energy ratios of 84, 88, 90, 93, 95, 96, 99, and 103 mg/kcal (P/E84, P/E88, P/E90, P/E93, P/E95, P/E96, P/E99, and P/E103), respectively. These diets contain different levels of gross energy (GE), ranging from 4.13 to 4.76 kcal g-1. Seven hundred and twenty healthy fish (17.15 ± 0.02 g) were randomly dispersed into 24 rectangular fiberglass tanks with 8 treatments in triplicate groups. The fish fed a P/E ratio of 95 mg/kcal demonstrated the best growth and feed utilization. A significant (P < 0.05) increase in percent weight gain (WG%) and specific growth rate (SGR) was seen as the dietary P/E ratio ameliorated from P/E84 to P/E95, followed by a decreased pattern in these parameters. Feed conversion ratio (FCR) and daily feed intake (DFI) were significantly impacted by dietary P/E ratios (P < 0.05). Additionally, an optimum P/E ratio improved intestinal morphology. However, low or high P/E ratio diets can cause oxidative stress, impaired liver function, and significantly reduced nonspecific immunity. The expression of target of rapamycin (TOR) and insulin-like growth factor-1 (IGF1) genes in the liver was considerably influenced by dietary protein-to-energy ratios (P < 0.05). Based on the statistical analysis of WG% against the dietary P/E ratio, the optimal P/E ratio for the studied species was estimated to be 92.92 mg/kcal. [ABSTRACT FROM AUTHOR]

In this study, SnO2-Sb2O3/GAC particle electrodes were prepared using the dip-calcination method. The particle electrodes were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer Emmett Teller (BET), thermogravimetric test and linear sweep voltammetry (LSV), which proved that the metal oxide was successfully loaded on the granular activated carbon and exhibited high electrocatalytic activity and thermal stability. The effects of initial pH, electrolytic voltage, electrolyte concentration, initial phenol concentration and particle electrode dosage on the performance of the three-dimensional (3D) electrocatalytic oxidation in phenol degradation were investigated. The results showed that under the optimal conditions, the removal rates of phenol and chemical oxygen demand (COD) were 99.65% and 67.16%, respectively. Finally, it was found that the novel particle electrodes had the ability of stable operation, maintaining high-efficiency operation no less than 15 times, which further highlights their robustness and durability. [ABSTRACT FROM AUTHOR]

In this study, a heterotrophic/biofilm‐electrode autotrophic denitrification reactor (HAD‐BER) was constructed and nano‐ɑ‐Fe2O3 was coated on granular activated carbon (GAC) as a third electrode to enhance the nitrate removal performance. The introduction of nano‐ɑ‐Fe2O3 could stimulate microorganisms to secrete more extracellular polymeric substances (EPS), accelerating the electron transfer. Moreover, more denitrification bacteria were enriched on the particle electrodes, especially Pseudomonas and Thermomonas, which played a significant role in denitrification. The denitrification performance at different COD/N ratios (0.65–3.23) and current intensities (0–150 mA) was investigated in depth. When the nitrate concentration of the influent was 60 mg/L, nitrate was almost completely removed at the optimal current intensity (60 mA) and COD/N ratio (1.29). At the same time, there was almost no nitrite (<0.10 mg/L) and ammonia nitrogen (0 mg/L) accumulation in the effluent. This study provided a new direction for the advancement of HAD‐BER and accelerated its implementation. Practitioner Points: By introducing nano‐a‐Fe2O3 into HAD‐BER, more denitrification bacteria were enriched on the particle electrodes.The increased contents of polysaccharide and protein content could accelerate the electron transfer.Almost completely denitrification could be achieved at current = 60 mA and COD/N = 1.29.The study provided a new direction for the further development of HAD‐BERs. [ABSTRACT FROM AUTHOR]

The exploration of information for aircraft wake vortex enables us to obtain new knowledge of wake turbulence separation standards. Traditional manual methods cannot work satisfactorily for the identification of great number of wake vortex data with high accuracy. Fortunately, the LiDAR intensity data can be explained by integrating LiDAR products with the strategies of computer vision. To overcome the limitation of traditional manual methods, this paper is aimed at developing an automatic method to identify a given set of wake vortices from various aircrafts. The main innovation works are outlined as follows. (1) From the wake vortex data that consists of various aircrafts measured by Wind3D 6000 LiDAR, a grayscale dataset of wake flow is constructed to boost the deep learning model for identifying aircraft wake vortex. (2) Following this, we propose a new method for the identification of aircraft wake vortex by modifying the VGG16 network, providing binary classifications of uncertain behavior patterns for wake vortices. To evaluate the proposed identification model, performance evaluation was conducted on our dataset, where experimental results revealed the values of 0.984, 0.951, 0.959, and 0.955 in terms of accuracy, precision, recall, and F1-score, respectively. [ABSTRACT FROM AUTHOR]

In order to reduce the wake separation between a ARJ21 aircraft and its front aircraft and to improve the airspace capacity and airport operation efficiency, theoretical analysis and experimental verification were carried out based on the actual detection of aircraft wake vortex data by airport wind lidar combined with the domestic aircraft ARJ21 aerodynamic response model. The aerodynamic force and moment of a ARJ21 aircraft under the action of different front aircraft wake were obtained. The results show that the ARJ21 is in no bump state when follows a B747 with an interval of 9.3km, and the rolling moment coefficient is less than the limit range. When follows a A320 or B737 with an interval of 6km, the ARJ21 is in the state of no turbulence, and the rolling moment coefficient is less than the limit range. The results show that the wake separation of a ARJ21 aircraft has a certain reduction space. [ABSTRACT FROM AUTHOR]

Wine‐processed Angelica Sinensis is a widely used Chinese medicinal decoction piece in China. However, there are hardly any robust markers indicating the processing procedure of wine‐processed Angelica Sinensis, including the amount of rice wine and processing degree. A strategy integrating untargeted metabolomics and chemometric analysis for deducing robust markers was provided and applied to the discrimination of processing procedure. First, 86 compounds were tentatively identified in wine‐processed Angelica Sinensis by ultra‐high‐performance liquid chromatography coupled with quadrupole‐time of flight mass spectrometry. Second, 93 potential chemical markers were selected using multivariate analysis, among which nine robust chemical markers were selected by verification with commercial samples. Finally, the effects of processing temperature, time, and amount of rice wine on the three selected chemical markers were investigated through a rapid analytical method. It was demonstrated that both m/z 258.1097 and 238.1189 were positively correlated with the amount of rice wine and processing degree. In summary, this study introduced two candidate processing markers as robust markers for discriminating the processing procedures of wine‐processed Angelica sinensis. It also proposed a strategy to provide the reference for the research of other decoction pieces. [ABSTRACT FROM AUTHOR]

Fish coloration, evolved from selection and adaptation, is a prominent feature of remarkable aquaculture merits. Fish possess more pigment cell types than any other vertebrates and are an excellent model for the study of mechanisms underlying skin coloration and pigmentation at levels from molecular genetics to system biology. How to effectively improve skin colour in ornamental and aquaculture fish has long been a focus on selective breeding programmes. In this review article, we introduce different types of chromatophore and early development of pigmentation, describe cellular mechanisms related to morphological and physiological changes of body colour and demonstrate applications of single‐sex control and molecular marker–assisted breeding in body colour selection. We also reviewed genes that have been found involving in neural crest migration and development, as well as those involved in melanin‐based coloration and other types of pigmentation, and explored how to use transgenic technology for enhancing fish body colour. The applications of genome editing and other omics technologies in relation to fish coloration are also illustrated. Finally, we present our perspectives about future fish coloration research and practice in aquaculture. Taken together, this review is expected to provide an update on cellular and molecular mechanisms in fish coloration and pigmentation, which will likely promote body colour–based molecular breeding programmes in aquaculture. [ABSTRACT FROM AUTHOR]

Huntington's disease (HD) is a progressive genetic neurodegenerative disease caused by an abnormal expansion of a cytosine-adenine-guanine trinucleotide repeat in the huntingtin gene. One pathological feature of HD is neuronal loss in the striatum. Despite many efforts, mechanisms underlying neuronal loss in HD striatum remain elusive. It was suggested that the mutant huntingtin protein interacts mitochondrial proteins and causes mitochondrial dysfunction in striatal neurons. However, whether axonal transport of mitochondria is altered in HD striatal neurons remains controversial. Here, we examined axonal transport of single mitochondria labelled with Mito-DsRed2 in cultured striatal neurons of zQ175 knock-in mice (a knock-in mouse model of HD). We observed decreased anterograde axonal transport of proximal mitochondria in HD striatal neurons compared with wild-type (WT) striatal neurons. Decreased anterograde transport in HD striatal neurons was prevented by overexpressing mitochondrial Rho GTPase 1 (Miro1). Our results offer a new insight into mechanisms underlying neuronal loss in the striatum in HD. • Cultured striatal neurons were mainly MSNs that are the most vulnerable neurons in HD. • Anterograde axonal transport of proximal mitochondria was altered in HD striatal neurons. • Overexpressing Miro1 prevented altered mitochondrial transport in HD striatal neurons. [ABSTRACT FROM AUTHOR]