Search

The environmental acceptability of geotechnical composites made of treated municipal sewage sludge (SwS) and paper ash (PA) after two different curing periods has been investigated. The mineral composition of such composites, including their content of major oxides, is mainly influenced by the PA. The content of potentially toxic elements (PTEs) in the initial materials and in the composites varies considerably. In the SwS the Ba, Cd, Cr, Cu, Hg, Ni and Zn contents are above the legally permitted limits. The PTE content of PA are lower, but still somewhat above the permitted values for Ba and Cu. Mixing these two materials together resulted in a decrease in the PTE, but the Ba, Cu and Zn contents are still too high for agricultural application. However, leachates from composites that had been cured for 28 days are highly alkaline, and the As, Ba, Cd, Cr, Hg, Mo, Ni, Pb and Zn contents in them are well below the permitted values. The Cu contents (2.4 to 5.4 mg/kg) are above the permitted limit for inert material, but inside the range for non-hazardous material. In a leachate of composite which was prepared with fresh PA and a lower PA to SwS ratio, the Cu content was 1.4 mg/kg, since fresh PA is more reactive and therefore has a higher ability to immobilise Cu. Therefore, such mixtures can be utilised for covers and liners for sanitary landfills.

Risk assessment and technical feasibility of brick formation from exhausted paper mill sludge derived biochar obtained after its use as an adsorbent for the treatment of effluent containing pentachlorophenol was studied. The bricks were prepared by geopolymerization mechanism in presence of sodium hydroxide, and the extent of geopolymerization was determined on the basis of crystal structure, surface functionalities, and surface morphology of the bricks. The preparation parameters (sodium hydroxide dosage, initial water and calcium carbonate content and curing temperature) were optimized and the results were analyzed in terms of compressive strength, water absorption, and abrasion index. Risk assessment of heavy metals was performed to determine the contamination level and overall hazard index of the biochar-based geopolymer bricks. Hazard quotient and hazard index were calculated to assess the overall non-carcinogenic risk posed by selected heavy metals via ingestion and dermal contact. The leaching potential of heavy metal and pentachlorophenol from the biochar-based geopolymer bricks was also determined. The results showed that the biochar-based geopolymer bricks showed good mechanical properties and the concentration of heavy metals in the leachate falls within the permissible limits prescribed by Indian Standards for Industrial and Sewage Effluents Discharge (inland surface water).

Thoron (Rn) exhalation from building materials has become increasingly recognized as a potential source for radiation exposure in dwellings. However, few studies have focused on mitigation strategies to reduce exposure from thoron and its progeny. Therefore, the purpose of this study is to (1) determine the reduction in thoron exhalation from building materials applied with regularly available surface barriers and (2) investigate the effects from surface roughness of the base material, barrier thickness, and surface cover on the thoron-retaining action of the surface barrier. The findings from this study demonstrate that regular surface barriers provide a potentially significant reduction in thoron exhalation, which can reach more than 90%. Despite this reduction, there are also materials that provide no reduction at all. Based on this work, no commonly available product property could be identified that provides good guidance on the barriers' performance to reduce thoron exhalation.

This article describes a study on the viability of using waste from the paper industry: biomass boiler ash and green liquor dregs to fabricate mortars and concretes. Both types of ash were characterized by obtaining their chemical and mineralogical composition, their organic matter content, granulometry, adsorption and other common tests for construction materials. Seven different mortars were fabricated, one for reference made up of cement, sand, and water, three in which 10, 20, or 30% of the cement was replaced by biomass ash, and three others in which 10, 20, or 30% of the cement was replaced with dregs. Test specimens were fabricated with these mortars to conduct flexural and compression tests. Flexural strength is reduced for all the mortars studied. Compressive strength increases for the mortars fabricated with biomass ash and decreases for the mortar with dregs. Finally, 5 concretes were made, one of them as a reference (neither biomass ash nor dregs added), two of them with replacements of 10 and 20% of biomass ash instead of cement and another two with replacements of 10 and 20% of dregs instead of cement. The compressive and tensile splitting strength increase when a 10% of ash is replaced and decrease in all the other cases. The modulus of elasticity always decreases., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Some Chilean copper slag dumps from the nineteenth century still remain, without a proposed use that encourages recycling and reduces environmental impact. In this paper, the copper slag abandoned in landfills is proposed as a new building material. The slags studied were taken from Playa Negra and Púquios dumps, both located in the region of Atacama in northern Chile. Pozzolanic activity in lime and Portland cement systems, as well as the alkali activation in pastes with copper slag cured at different temperatures, was studied. The reactivity of the slag was measured using thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), electrical conductivity and pH in aqueous suspension and Fourier Transform Infrared Spectroscopy (FTIR). Furthermore, copper slag-Portland cement mortars with the substitution of 25% (by weight) of cement by copper slag and alkali-activated slag mortars cured at 20 and 65 °C were made, to determine the compressive strength. The results indicate that the ancient copper slags studied have interesting binding properties for the construction sector., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

The production of paper pulp by the Kraft method generates considerable amounts of wastes. Namely, lime mud generated in the recovery circuit of chemical reagents, biological sludge from the wastewater treatment of wood digestion process and fly ash collected in the fluidized bed combustor used to generate electricity from biomass burning. The final destination of such wastes is an important concern, since environmental regulations are becoming stricter regarding their landfill. Driven by this fact, industries are looking for more sustainable solutions, such as the recycling in distinct products. This work tested these wastes as secondary raw materials to produce clinker/cement that was then experienced in mortar formulations. The first step involved the residues detailed characterization and a generated amounts survey. Then, specific but simple steps were suggested, aiming to facilitate transport and manipulation. Distinct blends were prepared and fired in order to get belitic and Portland clinkers. The Portland clinkers were processed at lower temperatures than the normally used in the industry due to the presence of mineralizing impurities in some wastes. Belite-based cements were used to produce mortars that developed satisfactory mechanical strength and did not reveal signs of deterioration or durability weaknesses., (Copyright © 2014 Elsevier B.V. All rights reserved.)

Objectives: Now, a lot of researchers have tried to make recycled rigid materials from the sludge cake produced in paper mill industries for the purpose of decreasing its volume. In this study, the researchers tried to make economically a disposable bin and to examine whether it is toxic or not to the outside environment., Methods: To make a disposable bin, the researchers used the sludge cake, a plastic basket, as a fixed mold, white cloth or newspaper, as a removable supporter for wrapping around the mold, and latex or plaster, as a binder. The strength of the samples was measured by tensile-stress testing. The water absorption was evaluated by Cobb test. As toxicological tests, leaching test and seed germination test were selected., Results: It was possible to form the disposal bin from the cleaned sludge cake. They seemed safe to carry garbage in the industry judging from the results of tensile-stress testing. Some of them showed less water absorptiveness (higher water resistance) in the results of Cobb test. The results of leaching test showed small values of three heavy metals, lead, nickel and copper, in the leachate. The seed germination test suggested no adverse effects of the bins in the clay and sand on the tomato growth., Conclusions: The results of these tests suggest that the bins have good strength, sufficient water resistance and no toxicological effect on the environment. This new recycled bin has the possibility to solve the environmental and health problems at disposing the sludge cake.

A field study was developed in a new landfill for refuse from construction and demolition (C&D) material recovery plants of small size (4 Ha.) in Europe, with the aim of evaluating the liquid and gas emissions in this type of facility at a large scale. It included characterization of the materials, monitoring leachate and gas quantity and composition. Besides thermometers, piezometers and sampling ports were placed in several points within the waste. This paper presents the data obtained for five years of the landfill life. The materials disposed were mainly made up of wood and concrete, similar to other C&D debris sites, but the amount of gypsum drywall (below 3% of the waste) was significantly smaller than other available studies, where percentages above 20% had been reported. Leachate contained typical C&D pollutants, such as different inorganic ions and metals, some of which exceeded other values reported in the literature (conductivity, ammonium, lead and arsenic). The small net precipitation in the area and the leachate recirculation into the landfill surface help explain these higher concentrations, thus highlighting the impact of liquid to solid (L/S) ratio on leachate characteristics. In contrast to previous studies, neither odor nuisances nor significant landfill gas over the surface were detected. However, gas samples taken from the landfill inside revealed sulfate reducing and methanogenic activity., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Waste management in construction is critical for the sustainable treatment of building-related construction and demolition (C&D) waste materials, and recycling of these wastes has been considered as one of the best strategies in minimization of C&D debris. However, recycling of C&D materials may not always be a feasible strategy for every waste type and therefore recycling and other waste treatment strategies should be supported by robust decision-making models. With the aim of assessing the net carbon, energy, and water footprints of C&D recycling and other waste management alternatives, a comprehensive economic input-output-based hybrid life-cycle assessment model is developed by tracing all of the economy-wide supply-chain impacts of three waste management strategies: recycling, landfilling, and incineration. Analysis results showed that only the recycling of construction materials provided positive environmental footprint savings in terms of carbon, energy, and water footprints. Incineration is a better option as a secondary strategy after recycling for water and energy footprint categories, whereas landfilling is found to be as slightly better strategy when carbon footprint is considered as the main focus of comparison. In terms of construction materials' environmental footprint, nonferrous metals are found to have a significant environmental footprint reduction potential if recycled., (© The Author(s) 2014.)

This paper presents the results of an investigation into the use of wastepaper sludge in geopolymer mortar systems for manufacturing construction products. The investigation was driven by the increasing demand for reuse options in paper-recycling industry. Both fresh and hardened geopolymer mortar properties are evaluated for samples incorporating dry wastepaper sludge, and the results indicate potential end-use benefits in building product manufacture. Addition of wastepaper sludge to geopolymer mortar reduces flow properties, primarily due to dry sludge absorbing water from the binder mix. The average 91-day compressive strength of mortar samples incorporating 2.5 wt% and 10 wt% wastepaper sludge respectively retained 92% and 52% of the reference mortar strength. However, contrary to the normal trend of increasing drying shrinkage with increasing paper sludge addition to Portland cement matrices, the corresponding geopolymer drying shrinkage decreased by 34% and 64%. Equally important, the water absorption of hardened geopolymer mortar decreased with increasing paper sludge content at ambient temperatures, providing good prospects of overall potential for wastepaper sludge incorporation in the production of building and masonry elements. The results indicate that, despite its high moisture absorbance due to the organic matter and residual cellulose fibre content, wastepaper sludge appears compatible with geopolymer chemistry, and hence serves as a potential supplementary additive to geopolymer cementitious masonry products., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

In the last ten years, as international environmental protection consciousness has increased, the study and applications of green building, green construction materials and energy savings as well as reduction of carbon dioxide have become urgent issues for governments. In Taiwan, joss papers are burned in more than 11,731 registered shrines or temples in traditional Chinese deity or ancestor worship ceremonies during special holidays or occasions. Instead of placing this large amount of burned joss paper ash (BJPA) in landfills, this study proposes recycling BJPA by replacing some cement with calcined BJPA (CBJPA) in mortar specimens. After BJPA samples were calcined at a high kiln temperature, mortar samples were created using CBJPA to replace cement at seven different levels: 0%, 5%, 10%, 15%, 20%, 25% and 30%. Tests like setting time and compressive strength were performed for macro-analyses; scanning electron microscopy-energy dispersive spectroscopy, X-ray diffraction and thermal gravimetric analysis/differential thermal analysis were carried out for the microstructure and chemical composition analyses. The test results showed that the compressive strengths of specimens with different levels of CBJPA replacement were apparently less than those of the control group (0% CBJPA) at all curing times. The compressive strength and setting time both decreased as the fraction of CBJPA in the mortar increased. Furthermore, because the hydration product did not cement and the mortar specimen structure was loose, the expected strength improvement from the pozzolanic reaction provided by the CBJPA was not clearly observed.

This paper presents results of an investigation into the use of de-inking sludge from a paper recycling mill as feedstock material in the manufacture of cement mortar products, including masonry blocks and mortar renders. Both physical and mechanical properties of mortar specimens containing various amounts of de-inking sludge were investigated. It was observed that the addition of de-inking sludge to cement mortar at a fixed water-to-cement ratio significantly reduced flow properties and increased setting time. Water absorption and volume of permeable voids of cement mortar increased with increased dosage of de-inking sludge, with a corresponding reduction of bulk density. The 91-day compressive strength of mortar samples with 2.5 wt% and 20 wt% de-inking sludge loadings retained 83% and 62% respectively of the reference mortar strength. The corresponding drying shrinkage increased by up to 160% compared to reference samples. However, a de-inking sludge loading of up to 2.5 wt% did not significantly alter measured physical and mechanical properties. The results demonstrate that despite the high moisture absorbance of de-inking sludge due to its organic matter and residual cellulose fibre content, it serves as a potential supplementary additive and its cellulosic content proving to be an active set retardant to cementitious masonry products., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

Sustainable waste management system for effluents treatment sludge has been a pressing issue for pulp and paper sector. Recycling is always recommended in terms of environmental sustainability. Following an approach of waste valorisation, this work aims to demonstrate the technical viability of producing fiber-cement roof sheets incorporating cellulose primary sludge generated on paper and pulp mills. From the results obtained with preliminary studies it was possible to verify the possibility of producing fiber-cement sheets by replacing 25% of the conventional used virgin long fiber by primary effluent treatment cellulose sludge. This amount of incorporation was tested on an industrial scale. Environmental parameters related to water and waste, as well as tests for checking the quality of the final product was performed. These control parameters involved total solids in suspension, dissolved salts, chlorides, sulphates, COD, metals content. In the product, parameters like moisture, density and strength were controlled. The results showed that it is possible to replace the virgin long fibers pulp by primary sludge without impacts in final product characteristics and on the environment. This work ensures the elimination of significant waste amounts, which are nowadays sent to landfill, as well as reduces costs associated with the standard raw materials use in the fiber-cement industrial sector., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

The results of assays carried out on plates used in the construction industry, manufactured entirely with solid wastes of a recycled paper plant, are presented and compared with the results obtained using agglomerated wood and plywood plates. Previous results had shown that wastes are composed essentially of polymers when these wastes are generated by recycled paper produced with the "waved type II" shavings. These solid wastes were placed in a mold that was heated and pressed with a hydraulic press in order to obtain the plates. The waste-produced plates were submitted to tests for humidity, swelling, water absorption, density, modulus of rupture-static bending, modulus of elasticity and direct screw withdrawal. These same assays had been carried out on two types of commercial wood plates, agglomerated wood and plywood, in order to compare the results with those obtained with the waste plate. Waste plates had similar behavior to the agglomerated wood plate, but it was possible to distinguish greater flexibility in the waste-produced plate and a significant difference in the tests for swelling and water absorption which showed the waste plate had a better performance than the agglomerated wood and plywood plates.

Aims: To survey paperboard products from 17 US mills for bacterial populations and for bacteria potentially harmful to human health., Methods and Results: Culturable aerobic bacteria were isolated from paperboard products using selective and nonselective medium. Resulting colonies from samples from three regions of the United States were identified using fatty acid methyl ester analysis. Percentages of bacteria species found were Bacillus megaterium (47), Bacillus licheniformis (15), Bacillus pumilus (12), Paenibacillus macerans (5), Paenibacillus pabuli (3), Bacillus subtilis (2), Bacillus cereus (2), Bacillus coagulans (1), Bacillus circulans (1), Bacillus brevis (1), Bacillus thuringiensis (1), Paenibacillus polymyxa (1), Cellulomonas turbata (1), Cellulomonas flavigena (1), unidentified Bacillus sp. (3) and unidentified bacteria (1)., Conclusions: Recycled paperboard contained high populations of bacteria, and a positive correlation was found between recycle content and bacterial populations. Escherichia coli, Salmonella, Shigella or confirmed coliform bacteria were not found in any product., Significance and Impact of the Study: Populations of bacteria did not differ significantly from original counts over a 4-month period of dry storage, indicating that bacteria persist in paperboard over long periods and may re-enter the recycling process. The predominance of heat-tolerant endospore-forming bacteria explains the high bacteria counts found in paperboard made from recycled materials.

The paper describes results obtained in the development of a previous research. We study here, in fast firing, the sintering behaviour and measure some properties of tiles containing a mixture of 60 wt% of paper mill sludge and 40 wt% of glass cullet. The behaviour of this material is compared to those displayed by materials obtained by the same mixture added with 10, 20 and 30 wt% of a natural red clay. In parallel, the same properties are measured also on a reference blend, which is presently used to produce commercial tiles. We show that powders containing 60 wt% of paper sludge and 40 wt% of glass cullet to which 30 wt% of clay is added give rise to materials that display a stable sintering process and have good hardness and strength and therefore could be used for the industrial production of tiles.

Background, Aim and Scope: One of the problems to affect Portland cement matrices is low resistance to aggressive agents, due principally to the presence of a high content of portlandite in the hydrated cements. Pozzolanic materials have played an important role in the improving the durability of cement-based materials for decades. This work studies the behaviour of cement mortar matrices blended with 10% calcined paper sludge (source for metakaolinite) and exposed to different environmental conditions (saline and non-saline environments) after 6 and 12 months of exposure., Materials and Methods: Two cements were studied: an ordinary Portland cement (CEM 1, 42.5R), acting as reference cement, and a blended cement formulated by mixing 90% (by mass) of CEM 1, 42.5R with 10% (by mass) of paper sludge calcined at 700 degrees C for 2 h. The specimens were exposed 1 year to saline and non-saline environments. All the mineralogy samples were studied through X-ray diffraction and scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analyser. The in-depth study on ionic mobility was performed on samples subjected to natural exposure (coast and tableland) for 6 and 12 months., Results: Portland cement was composed of quartz, calcite, calcium hydroxide and tobermorite gels. The pozzolanic cement (10% calcined paper sludge) is of the same composition but a high calcite concentration and barium carbonate. SEM analysis from coastline show deposits of variable composition. The deposits are identified on the surface of different mineral components. The minerals from tableland are much fractured, i.e. calcite and feldspars. Inside the fractures, the deposits and the ions are located and trapped superficially., Discussion: SEM analysis of control cement Portland and 10% calcined paper sludge shows deposits on quartz and calcite with a very high concentration of Pb, Zn, Cl and barium sulphate. A very porous aspect is due to the presence of the different aggregate types. This porous configuration permits retention of the ion environment. The pozzolanic cement in environments subject to the saline mist favours the retention and transport of ions observed. Something similar also happens with the increase in exposure to outdoor weather. Non-saline samples show temperature changes (ice or thaw cycles). Barium retention is kept on the surface in fracture lines by the gelification processes. In general, it may be inferred that an increase in exposure time increases the diffusion of ions towards test piece interiors. The chemical composition profiles show that the ions present different penetration speeds., Conclusions: The results indicate the better vulnerability of pozzolanic cements from calcined paper sludge in saline and non-saline environments. The cements with a 10% addition of calcined paper sludge favour retention and transport of ion has been observed., Recommendations and Perspectives: Today, projects are centred on a new recycling line for industrial waste of this kind, with special attention on its incorporation in cement manufacture as a pozzolanic material, setting the most appropriate activation conditions of the mineralogical compound in this waste (kaolinite and metakaolinite) and taking them as a starting point for this project. The use of pozzolanic cement with 10% addition of calcined paper sludge is a system which favours ionic retention.

The aim of this work is the experimental determination of effective transport properties of porous media consisting of compacted pieces of cardboard and polyethylene (PE). The proposed method itself is more general and can be applied to many different materials and contexts. Three major transport properties were determined: porosity, tortuosity factor and permeability. Three parameters characterizing the media were varied over a wide range: the bulk density, the size of the elements entering the mix, and the proportion of cardboard and PE in the mix. The properties were measured by means of a specially designed experimental device based on miscible gas tracing. The porosity and tortuosity factor were simultaneously determined by parametric identification, based on the experimental sample output response to an inlet gas concentration step change compared to the results of a direct numerical model. Permeability was calculated in the standard way from the measurement of the pressure drop across the sample. The reproducibility of the measurements was very good. It was found that changing the material density of the medium significantly affects all three structural properties. When the bulk density is varied between 300 and 900 kg m(-3), the tortuosity factor varies in a range as large as 18-8 and the permeability decreases by a ratio of 2-3. The tortuosity factor shows unusual variation, characterized by a decrease when density is increased above 500 kg m(-3). The size of the elements does not significantly affect the structural properties of the medium in the range of parameters studied.

New composite boards with low-thermal conductivity produced from a mixture of solid wastes from tissue paper manufacturing (solid waste TPM) and corn peel have been developed. The effects of solid waste TPM/corn peel ratio on the properties of the boards were investigated and the possibility of using recycled polystyrene packaging foam as a laminating agent to improve the quality of the boards was also evaluated. Our results show that the density of the particleboards decrease with increasing the amount of corn peel added in the mixture, leading to a decrease in thermal conductivity of the final product. In contrary, larger amount of solid waste TPM added in the mixture produced stronger boards. The lamination of recycled polystyrene on the surface of particleboards improves the mechanical properties and reduces the thickness swelling of the boards. The best improvement in mechanical properties and swelling resistance could be achieved when 15% polystyrene (w/v) was coated on the surface of the boards.

The technical properties of three layered cement-bonded boards (CBBs) made from wastepaper and sawdust were investigated. The CBBs were produced at three density levels of 1000, 1200 and 1300 kg/m3 and at four cement/particle ratios of 2.0:1, 2.5:1, 3.0:1 and 3.5:1 on a weight to weight basis. The technical properties evaluated were modulus of rupture (MOR), modulus of elasticity (MOE), water absorption (WA) and thickness swelling (TS). The MOR values ranged from 4.85 to 11.69 MPa and MOE values ranged from 2.80 to 5.57 GPa. The mean values of WA and TS after 24 h of water soaking of the CBBs ranged from 18.18% to 40.49% and 3.55% to 12.13%, respectively. MOR and MOE of the CBBs increased with increase in board density, but MOR decreased with the increase in cement/particle ratio. On the other hand, WA and TS decreased with increase in board density and cement/particle ratio. CBBs produced from wastepaper and sawdust at cement/particle ratios of 3.0:1 and 3.5:1 are suitable for building construction such as paneling, ceiling and partitioning.

The amount of corn stover that can be sustainably collected is estimated to be 80-100 million dry tonnes/yr (t/yr), a majority of which would be available to ethanol plants in the near term as only a small portion is currently used for other applications. Potential long-term demand for corn stover by non-fermentative applications in the United States is estimated to be about 20 million dry t/yr, assuming that corn stover-based products replace 50% of both hardwood pulp and wood-based particleboard, and that 50% of all furfural production is from corncobs. Hence, 60-80 million dry t/yr of corn stover should be available to fermentative routes. To achieve an ethanol production potential of 11 billion L (3 billion gal) per year (a target level for a non-niche feedstock), about 40% of the harvestable corn stover is needed. This amount should be available as long as the diversion of corn stover to non-ethanol fermentative products remains limited.

A new flame retardant and waterproof porous fiberboard was manufactured from waste newspapers by using a foaming agent and a reinforcing phenol-formaldehyde resin. To find the optimum conditions for forming fiberboard with high mechanical properties as well as flame retardant and waterproof characteristics, a series of experiments were performed with varying weight percentages of resin (w). The results indicate that the best quality of the fiberboard was obtained for w approximately 11%.

We conducted an evaluation of shredded paper insulation to identify potentially toxic components. The study was to provide a preliminary characterization of a few samples of insulation currently in use. The following samples were analyzed: previously produced insulation (PPI) containing fire retardants, shredded recycled paper (PPI feedstock), freshly produced insulation (FPI), and insulation which had been installed in a residence (II). Volatile constituents were analyzed by GC-MS from headspace air of samples held at room temperature or heated to 90 degrees C. Extractable constituents were sampled by extracting with methylene chloride, and analyzing by GC-MS. Formaldehyde analysis was done according to EPA Method TO11. Headspace air at room temperature contained no detectable quantities of volatile constituents for any sample measured. In headspace air at 90 degrees C, only PPI contained traces of aliphatic and aromatic hydrocarbons and higher aldehydes, and FPI traces of toluene. Extracts of PPI contained traces of octadecadienoic acid methyl ester and aliphatic and aromatic hydrocarbons and higher aldehydes. Extracts of PPI feedstock contained traces of a substituted cyclohexenecarboxylic acid. FPI contained extractable diethyl phthalate (30-50 micrograms/g). Extracts of II contained traces of methyl palmitate, an octadecenoic acid methyl ester, and a phthalate plasticizer. No formaldehyde was detected. PPI was composed of approximately 98 percent paper fiber and 2 percent pre-gelatinized starch. PPI samples agglomerated together with less than 0.01 percent separating from clumps as fine dust. Boron and sodium were expected and confirmed because they were added to PPI and FPI as fire retardants. Chromium, copper, iron, potassium, magnesium, manganese, phosphorus, and silicon were present at detectable concentrations. Study calculations indicate that an occupant would have to completely consume all the fine particles produced from 3.3 kg of insulation per day to have an intake of boron equivalent to the EPA RfD. No other constituent appeared to be present even close to toxicologically relevant amounts.

A comparison of death certificate statements on occupation for 858 white males who lived in coastal Georgia counties and who died of lung cancer during 1961--74, and for 858 controls who were of the same age and county of residence revealed a twofold excess risk of lung cancer associated with the construction industry. No elevated risk of lung cancer was found for workers in the wood and paper industries in the urban areas of Savannah, Brunswick, or Waycross, but a threefold increase was uncovered for the remaining coastal counties where the wood and paper industry was the largest employer.

Paper and cardboard elements can be used as a pro-ecological building material. To meet the safety and usage requirements paper elements need to be impregnated, however, most impregnation methods have a negative impact on the environmental performance of the elements. This article describes research that was conducted in order to determine the most effective technique of paperboard impregnation against water and humidity. Particular attention was given to biodegradable coatings, as several oil-based and wax-based wood impregnates were used. The samples were tested for 24 hours in immersion and for 48 hours in high air humidity. Water uptake (measured by the change in mass and thickness), delamination and deformation of samples were monitored. As a result, the basic characteristic of the tested impregnation methods was established – water and water vapour absorption, deformation or delamination after immersion. The lowest water and water vapour absorption was observed in samples impregnated with composed coatings of oils and waxes. [ABSTRACT FROM AUTHOR]

Sandwich panels with a core of corrugated cardboard The goal of a research project of the Institute for Steel Construction and Materials Mechanics was to determine the utilization of corrugated cardboard as a core material for sandwich panels for roof and wall cladding. In contrast to common core materials, corrugated cardboard is recyclable and consists of renewable raw materials. The bearing behaviour depends mainly on the paper types and on the orientation of the anisotropic material inside the panel. The weakest orientation has similar stiffness and strength as common core materials. However, these can be exceeded many times by other core orientations. Investigations of the most important building physical parameters have shown that the fire behaviour is slightly better than that of most PU‐sandwich panels. The thermal conductivity in the weakest core orientation is comparable to that of mineral wool, the stronger core orientations show higher thermal conductivity. [ABSTRACT FROM AUTHOR]

The hemp plant Cannabis sativa Linn, referring to industrial hemp, is a high-yielding annual industrial crop grown providing fibers from hemp stalk and oil from hemp seeds. Although hemp is a niche crop, hemp production is currently undergoing a renaissance. More than 30 countries grow hemp, with China being the largest hemp producing and exporting country. Europe and Canada are also important actors in the global hemp market. Traditionally, hemp as a fiber plant has been used for the production of apparels, fabrics, papers, cordages and building materials. The hurds, as waste by-product of fiber production, were used for bedding of animals, the seeds for human nutrition, e.g., as flour, and the oil for a wide range of purposes, from cooking to cosmetics. Hemp has also been an important crop throughout human history for medicine. Other more recent applications include materials for insulation and furniture, automotive composites for interior applications and motor vehicle parts, bioplastics, jewelry and fashion sectors, animal feed, animal bedding, and energy and fuel production. Foods containing hemp seed and oil are currently marketed worldwide for both animal and human nutrition. They also find applications in beverages and in neutraceutical products. Hemp oil is also used for cosmetics and personal care items, paints, printing inks, detergents and solvents. It is estimated that the global market for hemp consists of more than 25,000 products. Currently, the construction and insulation sector, paper and textile industries, and food and nutrition domains are the main markets while the cosmetics and automotive sector are growing markets. Innovative applications, e.g., in the medical and therapeutic domains, cosmeceuticals, phytoremediation, acoustic domain, wastewater treatment, biofuels, biopesticides and biotechnology, open new challenges. Hemp is also the object of numerous fundamental studies. This review presents and discusses the traditional and new uses of industrial hemp. [ABSTRACT FROM AUTHOR]

Novel sandwich composites made of syntactic foam core and paper skin were developed as potential building materials. Interface bonding between core and skin was controlled by varying starch content. Two different microsphere size groups were employed for syntactic foam core manufacturing based on the pre-mold processing method. Properties of skin paper with starch adhesive on were found to be affected by drying time of starch adhesive. Mechanical behavior of manufactured sandwich composites in relation with properties of constituent materials was studied. Skin paper contributed to increase up to 40% in estimated flexural strength over syntactic foams, depending on starch content in adhesive between syntactic foam core and paper skin. Small microsphere size group for syntactic foam core was found to be advantageous in strengthening of sandwich composites for a given starch content in adhesive. This finding was in agreement with calculated values of estimated shear stress at interface between skin and core. Failure process of the sandwich composites was discussed in relation with load–deflection curves. Cracking of syntactic foam core was detected to be the first event in sandwich composite failure sequence. Hygroscopic behavior of syntactic foam panels was investigated. Moisture content in the foam was measured to be high for high starch content in the foam panels. No significant moisture effect on flexural strength of syntactic foam panels after being subjected to moisture about 2 months was found for both microsphere size groups. However, substantial decrease (28%) in flexural modulus was found for the foam panels made of large microspheres although not much moisture effect was found on that of small microspheres. [ABSTRACT FROM PUBLISHER]

• Bricks made by bottom ashes, cellulose fibers and clay have been successfully made and tested. • Optimum blends are made of 70% of clay, 25% of bottom ashes and 5% of cellulose fibers. • The so made bricks comply mechanical requirements and are 20% lighter. • Lower thermal conductivity and equal specific heat capacity is achieved. • Toxicity analysis abides by standards in force. The paper and pulp industry (PPI) is permanently searching for new ways of managing its residues due to the increasing pressure of new environmental concerns and policies adopted worldwide. In addition, the manufacturing of construction materials such as fired clay bricks (FCBs) is also facing the transformation of its traditional market, which is asking for new materials with a lower environmental footprint but equal or even better technological properties. In considering the large mass flows related to both the PPI and FCB industries, several researchers have pointed out the feasibility of replacing clay by residues produced by PPI. However, these approaches have always considered the replacement of a single residue rather than the addition of several new ones. Conversely, by using both residues at once, the overall FCB performance is improved and the feasibility of this circular economy approach is eased. For instance, the addition of woody fibres increases thermal resistance but reduces mechanical strength. Conversely, the addition of ashes produced by PPI improved the mechanical strength by reducing the thermal resistance due to the increasing content of fluxing agents which improve the fired clay matrix structure. For this reason, this paper explores the technological properties achieved by replacing clay with both ashes and fibres provided by PPI in an integrated approach. By following industrial procedures, the so made fired clay bricks (with 20% of ash and 5% of fibres) meet the standard and show approx. 20% less thermal conductivity, with the same thermal capacity and a density reduction of more than 15%. [ABSTRACT FROM AUTHOR]

In this paper, a brief review on reversible dielectric nonlinearity (RDN) was presented and the mechanism of tunability for ferroelectric ceramics was discussed in several different scale levels, such as atomic level (intrinsic nonlinearity described by ferroelectric thermodynamic theory), nano-meter scale (polar nano-region response), submicron scale (ferroelectric domain and domain wall motion), micron scale (polycrystalline structure of ceramics and surface layer) and macroscopic scale (field induced phase transition). It suggests that RDN is a multi-scale phenomenon and is temperature and frequency-sensitive. The halving field E0 in Roberts' Equation may be a good attempt for the quantitating of RDN. The stability of RDN in paraelectric phase is also mentioned. [ABSTRACT FROM AUTHOR]