Search

DC grid has become an important application in power transmission. However, the exist works only have the method to obtain the droop coefficient in a radial topology. Also, this droop coefficient is for V-I droop control. There is no such like method to obtain the droop coefficient for the P-V droop control. This paper proposed a new method for a complex dc grid to obtain the droop coefficients. Firstly, based on the converter control strategies, the types of converter were classified. It will help to find out which kinds of converter can be participated into the dc-side voltage control. Secondly, a virtual node was defined, and the matrix of the dc grid was reshaped to fit the new added virtual node by using the proposed simplification method. An example was shown how this method worked. After that a new method of calculating the P-V droop coefficient was proposed. Finally, a simulation model was investigated to verify if the proposed method can operate in a real system. The results showed that the simplification method can ensure the mathematical relationships of the dc system. And simulations show good performances of the droop coefficient calculation method. [ABSTRACT FROM AUTHOR]

This article brings forward a design method of virtual resistance for droop-controlled dc microgrids (DCMGs). Although droop control is widely employed in coordinated DCMGs to coordinate different energy sources, few works address thoroughly the principles for a proper virtual resistance design. In this article, dynamic stability and static voltage deviation constraints are taken into consideration as the main criteria to be complied with by the virtual resistance design. In critical cases, constant power loads (CPLs) may substantially decrease system damping and adversely affects the stability of the system. In this sense, the large-signal stability model is developed including CPLs by using the Lyapunov function, and it is subsequently analyzed to infer the stability criterion. Theoretically, bus voltage is the most important index when addressing the DCMG control; hence, the impact of virtual resistance on the voltage deviation is explored as well. The research presented in this article finds out that virtual resistance influence on system stability is opposite to that on voltage deviation; thus, a tradeoff method based on the containment principle is developed. Throughout the proposed compromised design, we can adjust the weight coefficient to satisfy different performance requirements of DCMGs. The effectiveness of the proposed scheme is validated through experimental results. [ABSTRACT FROM AUTHOR]

In the literature, many studies on stability analysis of dc microgrids have been conducted. However, most of them mainly focus on small-signal stability. On the other hand, few works analyze large-signal stability, but the major part of these works is based on a single unit or a simple cascaded system as a case study. Different from those, this article aims to address the large-signal stability analysis of a dc microgrid from a system-level perspective. First, the equivalent model of a droop-controlled dc microgrid is developed. Subsequently, the Lyapunov-based large-signal stability analysis and the stability criterion are derived, and mixed potential theory is used to make comparisons to verify the effectiveness of the derived criterion. The equilibrium point stability for different operation stages was obtained by means of theoretical calculation. Furthermore, the instabilities principle as well as their physical interpretation is revealed. In this article, the bus voltage is used as the only index to assess the microgrid power balance. Hence, the power load limit can be obtained by taking into consideration the stability and voltage deviation constraints. Finally, simulation and experimental results from a four-converter dc microgrid system verify the feasibility of the proposed theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a decentralized current-sharing control strategy to endow fast transient response to paralleled dc–dc converters systems, such as dc microgrids or distributed power systems. The proposed controller consist of two main control loops: an external voltage droop control for current-sharing proposes and an internal current loop. The external droop control loop is designed as a voltage loop with embedded virtual impedance, which avoids the use of a slow voltage loop and a separate extra virtual impedance loop that may limit the system bandwidth. The internal current loop, thanks to the external control loop simplification, plays a major role in the system bandwidth, so that an adaptive proportional-integral (PI) controller is proposed for this matter. In the paper, two different droop control methods have been modeling, designed, simulated, and tested: The conventional virtual-impedance-loop based V–I droop and the proposed embedded-virtual-impedance based I–V droop. In order to compare the dynamic response performances between two droop controllers, their state-space models have been developed and analyzed in this paper. The results show that the dynamic response of the I–V droop control is faster than that of the conventional V–I droop control. Furthermore, by analyzing the effects from I–V droop control parameters, the errors can be reduced faster by enlarging the proportional terms, but with no fluctuations, and then completely eliminated by restoring back to small proportional values. Meanwhile, there exists a tradeoff phenomenon between the fast dynamic response and good steady-state performance; thus, an adaptive PI controller is proposed to both improve dynamic response and guarantee good steady-state performance simultaneously. Experimental results are shown to verify the accuracy of the models and the effectiveness of the proposed control framework. [ABSTRACT FROM PUBLISHER]

Harnessing wind energy is the most rapidly growing amongst renewable energy sources. However, because of its intermittency in nature, wind power results in unfavorable influences on power system control, operation and stability. The voltage sag and flicker and grid frequency fluctuation are significant in this regard. To minimize the effect of wind power fluctuations and other contingencies on the grid frequency and AC-bus voltage, this paper presents a droop-fed vector control strategy based variable speed pumped storage (VSPS) system comprising the doubly fed induction machine. Modelling of the system is undertaken based on a phasor model technique. The case study is made by considering the droop-controlled VSPS plant in a grid containing conventional synchronous machines for hydropower and thermal power plants and an induction machine wind farm. The performance is validated and analyzed using a MATLAB/Simulink platform. The proposed droop-fed control model is compared with the conventional control strategy (without being droop-fed) and tested to wind power fluctuations, start-up transients, load variations and three-phase fault. The results show that the droop-fed vector control strategy of the VSPS plant achieves better dynamic and steady state controlling responses for grid frequency and AC-bus voltage in the power system than the conventional vector control scheme during wind power fluctuations and contingencies. [ABSTRACT FROM AUTHOR]