Search

The importance of flexible alternating current transmission system (FACTS) devices is increasing day by day as they provide compensation for power systems. The installation of such devices solves many issues regarding the stability and power transferability of power systems. However, for optimizing the performance of FACTS devices, the location and sizes of FACTS devices must be selected very carefully. On the other side, the utilization of optimization techniques is increasing daily, as it is capable of solving nonlinear, random problems by its stochastic nature. As a result, it became a reliable tactic for solving stochastic problems almost in every aspect of our lives. Therefore, it is adopted for solving power system problems, like, FACTS devices allocation, distributed generators allocation, determining component's parameters, and more. In this paper, the optimal size and location of several FACTS devices are selected to achieve the following single objective functions separately: fuel cost minimization and power losses minimization, then combining the mentioned objective function into one multiobjective function for gross cost minimization. The power system optimized is the Institute of Electrical and Electronics Engineers 30‐bus standard system, and the FACTS devices installed are static VAR compensator, thyristor control series compensator, and thyristor‐controlled phase shifter, while the optimization is performed using different conventional and recent optimization algorithms, including a newly developed algorithm, typically Leader Walrus Optimization Algorithm "LWaOA," making a comparison among such algorithms to investigate the algorithm that possesses the best performance. The results of the optimization processes show the superiority of LWaOA. [ABSTRACT FROM AUTHOR]

This work focuses on the use of the Linear Quadratic Gaussian (LQG) technique to construct a reliable Static VAr Compensator (SVC), Thyristor Controlled Series Compensator (TCSC), and Excitation System controller for damping Subsynchronous Resonance (SSR) in a power system. There is only one quantifiable feedback signal used by the controller (generator speed deviation). It is also possible to purchase this controller in a reduced-order form. The findings of the robust control are contrasted with those of the "idealistic" full state optimal control. The LQG damping controller's regulator robustness is then strengthened by the application of Loop Transfer Recovery (LTR). Nonlinear power system simulation is used to confirm the resilience of the planned controller and demonstrates how well the regulator dampens power system oscillations. The approach dampens all torsional oscillatory modes quickly while maintaining appropriate control actions, according to simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes a novel method to find the optimal location of the shunt connected Flexible AC Transmission Systems (FACTS) such as Static Var Compensator (SVC) or Static Synchronous Compensator (STATCOM) to the power system for regulating voltage levels of all buses. Three indices include Voltage Drop Index (VDI), Total Voltage Drop Index (TVDI), and Total Voltage Drop of Network Index (TVDNI) are presented to find the location of the SVC. Also, to minimize the solution space, a ranking list will be established. For the case studies, the IEEE 14-bus test system is selected, and an SVC is located in the system. Simulations are done in two cases: network loads increase with constant coefficient and randomly. According to simulation results in both cases, the proposed method can identify the optimal placement of SVC, and the voltage drop due to increasing the load will be compensated. For the IEEE 14-bus test system, the optimal location of the SVC is bus 9. Variable loads are considered for 24 h, and SVC is installed at bus 9 to validate the introduced method. Results show the voltage level for all buses is compensated so that the voltage levels are higher than the minimum voltage level, i.e. 95%. [ABSTRACT FROM AUTHOR]

A constant worldwide growing load stress over a power system compelled the practice of a reactive power injection to ensure an efficient power network. For this purpose, multiple technologies exist in the knowledge market out of which this paper emphasizes the usage of the flexible alternating current transmission system (FACTS) and presents a comparative study of the static var compensator (SVC) with the static synchronous compensator (STATCOM), inducted in a real electric substation. The aim is to improve the power factor (PF) and power quality and to encounter reliably extreme conditions. A 220 kV electric substation was opted for the analysis, and both the static and dynamic conditions were observed with the help of a power system analysis tool termed PowerFactory-DIgSILENT. Multiple aspects were investigated via software simulations to assess the performance of the aforementioned FACTS devices, such as the voltage profile evaluation via the load flow analysis method (LFA), the harmonic response via the power quality and harmonic analysis tool, and the short-circuit response via the RMS simulation tool. The outcomes were verified and compared with permissible values included in the universal standards, such as IEC and IEEE. The superiority of the STATCOM over the SVC was proven in light of the simulative results. [ABSTRACT FROM AUTHOR]

The goal of multi-criteria decision making (MCDM) is to select the most appropriate of the alternatives by evaluating many conflicting criteria together. MCDM methods are widely available in the literature and have been used in various energy problems. The key problems studied in electrical power systems in recent years have included voltage instability and voltage collapse. Different flexible alternating current transmission systems (FACTS) equipment has been used for this purpose for decades, increasing voltage stability while enhancing system efficiency, reliability and quality of supply, and offering environmental benefits. Finding the best locations for these devices in terms of voltage stability in actual electrical networks poses a serious problem. Many criteria should be considered when determining the most suitable location for the controller. The aim of this paper is to provide a comparative analysis of MCDM techniques to be used for optimal location of a static VAR compensator (SVC) device in terms of voltage stability. The ideal location can be determined by means of sorting according to priority criteria. The proposed approach was carried out using the Power System Analysis Toolbox (PSAT) in MATLAB in the IEEE 14-bus test system. Using ten different MCDM methods, the most appropriate locations were compared among themselves and a single ranking list was obtained, integrated with the Borda count method, which is a data fusion technique. The application results showed that the methods used are consistent among themselves. It was revealed that the integrated model was an appropriate method that could be used for optimal location selection, providing reliable and satisfactory results to power system planners. [ABSTRACT FROM AUTHOR]

This paper presents the application of Flexible Alternating Current Transmission System (FACTS) devices based on heuristic algorithms in power systems. The work proposes the Autonomous Groups Particle Swarm Optimization (AGPSO) approach for the optimal placement and sizing of the Static Var Compensator (SVC) to minimize the total active power losses in transmission lines. A comparative study is conducted with other heuristic optimization algorithms such as Particle Swarm Optimization (PSO), Timevarying Acceleration Coefficients PSO (TACPSO), Improved PSO (IPSO), Modified PSO (MPSO), and Moth-Flam Optimization (MFO) algorithms to confirm the efficacy of the proposed algorithm. Computer simulations have been carried out on MATLAB with the MATPOWER additional package to evaluate the performance of the AGPSO algorithm on the IEEE 14 and 30 bus systems. The simulation results show that the proposed algorithm offers the best performance among all algorithms with the lowest active power losses and the highest convergence rate. [ABSTRACT FROM AUTHOR]

Flexible AC transmission systems (FACTS) technology is widely adopted and utilized to maintain the performance of power systems. However, the improvements of power system performance achieved by FACTS devices depend on the right sizing and allocation of such devices. For technical and economic considerations, a FACTS device's location and size should be selected very carefully in order to maximize its benefits to the power system. In this paper, the sizing and location of a static VAR compensator (SVC) are optimally determined using a new optimization technique called lightning attachment procedure optimization (LAPO). The optimal allocation of the SVC is determined regarding the improvement of voltage deviation index and the reduction of total active power losses. The system is optimized in two cases: once without SVC installation in order to find out the optimal settings of the system that achieve the objective functions, and another time with SVC installation to determine its optimum sizes and locations by which the required objective functions are achieved. Then the system performance is analyzed after optimization with and without SVC devices to show the impact of the optimum sizing and location of the SVC on the system. The study is validated using the standard IEEE 30-bus system, while the developed LAPO is performed by MATLAB M-Files and the system performance analysis in different cases is performed by NEPLAN software. [ABSTRACT FROM AUTHOR]

Power quality is often defined as the electrical network's or the grid's capability to deliver a clean and stable power supply. Flexible AC transmission systems (FACTS) devices consist of power electronics circuits that's depend on the thyristor for controlling active and reactive power flows and to maintain the voltage within the allowable limits in normal and abnormal operating conditions. Static Var Compensation (SVC) is one of the most important FACTS devices, that's combined between shunt capacitor and shunt reactor, that's connect with the system by control setting. The control of reactive power by SVC module is depending on firing angle of thyristors. The shunt capacitor module can be called thyristor switched capacitors (TSC) and thyristor-controlled reactors (TCR), that's provide harmonic filters and/or dynamic shunt compensation. TSC operates with series bi-directional thyristor and a damping reactor to prevent the shunt resonance, the thyristors are used to control the capacitor to operate at the required value. TCR operates with series thyristor switch for control. SVC is easy and more accurate to operate with the medium voltage. SVC can be connected with the extra high voltage system via step-down transformer. This paper discusses the SVC to be uses to improve the power system quality, by adding the reactive power to the system. Also, this paper discusses the SVC control by using the MATLAB/Simulink software to discuss the step operation for the SVC with the power system. [ABSTRACT FROM AUTHOR]

This paper proposes the design of auxiliary-coordinated controller for static VAR compensator (SVC) and thyristor-controlled series capacitor (TCSC) devices by adaptive fuzzy optimized technique for oscillation damping in multimachine power systems. The performance of the coordinated control of SVC and TCSC devices based on feedforward adaptive neuro fuzzy inference system (F-ANFIS) is compared with that of the adaptive neuro fuzzy inference system (ANFIS) structure based on recurrent adaptive neuro fuzzy inference system (R-ANFIS) network architecture. The objective of the coordinated controller design is to tune the parameters of SVC and TCSC fuzzy lead lag compensator simultaneously to minimize the deviation of rotor angle and rotor speed of the generators. The performance of the system is enhanced by optimally tuning the membership functions of fuzzy lead lag controller parameter of the flexible AC transmission system (FACTS) by R-ANFIS controller. The training data for F-ANFIS and R-ANFIS are generated by conventional linear control technique under various operating conditions. The offline trained controller tunes the parameter of lead lag controller in online. The oscillation damping ability of the system is analyzed for three-machine test system by calculating the standard deviation and cost function. The superior performance of R-ANFIS controller is compared with various particle swarm optimization-based feedforward ANFIS controllers available in literature. [ABSTRACT FROM AUTHOR]

• Computational modeling to evaluate the LOE protection of synchronous generators connected to a transmission line with static var compensator (SVC). • Comparative of traditional LOE protection of with a proposed LOE protection method based on a multilayer perceptron-type artificial neural network (ANN). • Show the effectiveness of the proposed ANN LOE protection to reach faster actuation time than the traditional LOE protection. Flexible Alternating Current Transmission Systems (FACTS) connected to Transmission Lines (TLs) make systems more flexible, and optimize their operational capacity. Despite improvements in TL operational aspects, added FACTS can modify the amplitude, voltage, and current angles of the system wherein they are inserted and consequently the measured impedance, which can affect synchronous machine protections that are based on this feature. Firstly, this paper presents a set of computational simulations to evaluate possible changes in the synchronous machine protection connected to a TL with Static Var Compensator (SVC). Finally, is this context the traditional loss of excitation (LOE) protection is comparing with a proposed approach based on the use of a multilayer perceptron-type Artificial Neural Network (ANN). The simulation results show the effectiveness and robustness of the proposed ANN LOE protection to reach faster actuation time than the traditional LOE protection. [ABSTRACT FROM AUTHOR]

In order to increase the power transfer and providing the optimum utilisation of the power system capability, application of flexible alternating current transmission system (FACTS) devices technology, such as static synchronous compensator (STATCOM), has been attracted, in recent years. However, the STATCOM changes the voltage and current of the power system that disturb the operation of the impedance‐based synchronous generator loss of excitation (LOE) protection. Then, this study proposes a new flux‐based LOE protection method, in the presence of STATCOM, that is based on the local variation of the flux linkage of the generator available at the location of relay. The mentioned relay is independent of other generator protection relays without any coordination. In order to show the satisfying operation of the proposed method, some simulations have been carried out in the Matlab/Simulink software. A single‐machine infinite bus and a three‐machine infinite bus systems have been used in simulations. The results show that the presence of STATCOM has no important effect on the performance of proposed relay opposite to a negative offset relay with two protective zones (the widely used impedance method) which is affected by STATCOM operation. [ABSTRACT FROM AUTHOR]

STATCOM is a FACTS controller that is used in power systems to regulate the line voltage, enhance the power transmission capacity and extend the transient stability margin. STATCOM is conventionally realized by a voltage-source converter; however, being a current injection device, its performance can be improved when realized by a current-source converter (CSC) that can generate a controllable current directly at its output terminals. In this paper, a STATCOM based on the current-source converter topology is proposed. The nonlinear model of the current-source converter, which is the source of the difficulties in the controller design, has been modified to a linear model through a novel modeling technique. The proposed modeling technique is not based on the linearization of a set of nonlinear equations around an operating point. Instead, the power balance equation and a nonlinear input transformation are used to derive a linear model independent of the operating point. This model acts as the basis for the design of a decoupled state-feedback controller. The proposed STATCOM has been simulated using the PSCAD/EMTDC package. The simulation results show that a CSC-based STATCOM can result in excellent current and voltage waveforms as well as very short response time while operating at a low switching frequency. This makes the proposed scheme suitable for high power applications. [ABSTRACT FROM PUBLISHER]

In the modern power system, Flexible Alternating Current Transmission System (FACTS) devices are widely used. An increased share of the distributed generation (DG) and the development of microgrids change the power flows in the existing distribution networks as well as a conventional power flow direction from the transmission to the distribution network level which may affect the overall stability aspects. The paper shows the FACTS devices' implementation influence on the performance of the distribution network with integrated renewable energy sources (RES) observing the aspects of the oscillatory stability and the low-voltage motor starting. The FACTS devices, in particular the static var compensators (SVC), have been allocated according to a novel algorithm proposed in the paper. The algorithm uses an iterative process to determine an optimal location for implementation and rating power of SVC considering active power losses minimization, improvement of the voltage profile and maximizing return of investment (ROI) of FACTS devices. Novel constraints—transformer station construction constraint, SVC industrial nominal power value constraint and the constraint of distribution system operator (DSO) economic willingness to investment in the distribution network development are considered in the proposed algorithm. The analysis has been performed on 20 kV rural distribution network model in DIgSILENT PowerFactory software. [ABSTRACT FROM AUTHOR]