Search

Pressure retarded osmosis (PRO) is an innovative technique to yield osmotic energy. Nevertheless, the PRO performance is exacerbated by the severe membrane fouling occurring within the porous support. It is a potential alternative for sustainable power harvesting to change the membrane orientation from active layer facing draw solution (AL−DS) or PRO mode to active layer facing feed solution (AL−FS) or FO mode for a low-fouling propensity. A novel integral PRO hollow fiber membrane was developed in this work by phase inversion and followed with a facile cross-linking post-treatment. The structure and properties of the resultant membrane were systematically investigated using a series of characterization protocols. The PRO performance of the membrane was studied under various hydraulic pressures at the AL−FS orientation. The results reveal that the substrate with sponge-like structure and relatively dense inner surface can better withstand high pressure in PRO process. Two steps of cross-linking endowed the membrane with a smaller pore size on the outer surface that exhibits high rejection against various inorganic salts. The novel integral membrane can achieve a stable power density output around 4.3 W m −2 at 12 ~ 13 bar hydraulic pressure, using a real wastewater reverse osmosis (RO) retentate and 1.0 M sodium chloride as the feed and draw stream, correspondingly. This result demonstrates that the PRO operation in the AL−FS orientation (FO mode) offers a significant advantage over the AL−DS orientation (PRO mode) by eliminating the pretreatment of the feed water or/and other measures associated with membrane fouling control in the PRO mode. To implement the PRO operation with the AL−FS orientation, developing a robust membrane with an integral structure is critical. The newly developed integral hollow fiber membrane via chemical cross-linking presents the potential for PRO operation in the AL−FS orientation. [ABSTRACT FROM AUTHOR]

The emerging technology of pressure retarded osmosis (PRO) has been intensely studied over the past decades due to its potential in harvesting salinity gradient energy, but membrane fouling can deteriorate the PRO performance. To mitigate membrane fouling, the outer surface of the inner-selective thin-film composite (TFC) polyetherimide (PEI) hollow fiber membrane was modified by depositing poly-(allylamine hydrochloride) (PAH) and poly acrylic acid (PAA) polyelectrolytes. The results show that the outer surface of the modified membrane had less pores exposed and was more negatively charged, which was beneficial for preventing the entrance and adsorption of the negatively charged foulants into the membrane substrate. It was further proved that the modified membrane was effective in reducing PRO fouling by organic macromolecules such as alginate and bovine serum albumin, while maintaining the mechanical properties and intrinsic separation properties well. Interestingly, after 200 ppm alginate was introduced to the feed water, the power density of the modified membrane could be maintained constant at 16.2 W·m − 2 at 15 bar while that of the non-modified membrane reduced around 17% at the end of a 300-min testing period. The results suggest that the polyelectrolytes deposition is a feasible strategy for adding anti-fouling property to PRO membranes. [ABSTRACT FROM AUTHOR]

Novel composite forward osmosis (FO) hollow fiber membranes with two selective skin layers were developed in the present work. The polyethersulfone (PES) hollow fiber substrate was firstly fabricated by a phase inversion method. The RO-like polyamide skin layer was then prepared on the inner surface of the hollow fiber substrate via interfacial polymerization (IP), while the NF-like outer skin layer was prepared via polyelectrolyte layer-by-layer (LBL) assembly. Three double-skinned membranes with negative (DS#1.5), positive (DS#2.0) and minimal (DS#2.5) outer surface charges under neutral pH environment were evaluated for their capabilities against organic fouling in the FO process. The newly developed double-skinned membranes possess water permeability greater than 2 l/m 2 h bar and NaCl rejection higher than 95% under 2 bar pressure, and have superior water flux and less salt leakage than the commercial HTI FO membranes as well as all the reported double-skinned FO membranes with RO-like selective layers. Most importantly, the double-skinned DS#2.5 hollow fiber membrane exhibits exciting organic fouling resistance because of its highly hydrophilic NF-like secondary layer with minimal surface charge and tightened surface structure to mitigate possible substrate pore clogging and fouling layer formation. A stable water flux of around 25 l/m 2 h was attained for DS#2.5 membrane using <0.5 M NaCl as the draw solution and a water containing 200 ppm dextran (DEX) or Aldrich humic acid (AHA), or lysozyme (LYS) and 10 mM NaCl as the model feed in the active layer against the draw solution (AL-DS) configuration, suggesting its great potential for practical FO applications. [ABSTRACT FROM AUTHOR]

Highlights: [•] Effect of intrinsic properties of foulants on FO membrane performance was studied. [•] Diffusivity governs hollow fiber membrane performance in FO mode. [•] Flat sheet membrane performance in PRO mode was controlled by combined mechanisms. [•] The mechanisms include diffusivity, size exclusion and electrostatic interactions. [ABSTRACT FROM AUTHOR]

Thin-film composite (TFC) membranes are generally preferred over integrally skinned asymmetric (ISA) membranes in pressure retarded osmosis (PRO) process due to their much higher water permeability, but they cannot operate in the active layer facing feed solution (AL-FS) orientation because of potential delamination of the rejection layer under the high applied pressure. However, operating under AL-FS orientation is preferred as a strategy for better fouling control. Hence, in this study, three ISA hollow fiber membranes were fabricated using a dry-jet wet-spinning method, followed by chemical cross-linking to obtain membranes for PRO application. The best-performing membrane was subjected to fouling test in two orientations. Our results demonstrate that the AL-FS orientation is better for a sustainable long-term PRO operation, given the stable performance throughout the two-day testing. Also, the current use of power density per membrane area as a performance benchmark may not be practical for large-scale PRO operation, and the volumetric power density per module is more relevant. In terms of volumetric power density for a hypothetical 5-in. module, our best-performing membrane is predicted to generate a 3.6 to 10 times better power density than commercial modules, rendering our ISA hollow fiber membranes promising for scaling-up to bigger modules. [Display omitted] • Operating under AL-FS orientation is preferred as a strategy for better fouling control. • Integrally skinned asymmetric hollow fiber membranes were developed for AL-FS orientation in PRO. • The membranes achieved sustainable power production when wastewater was employed. • The volumetric power density was predicted to yield promising solution for practical application. [ABSTRACT FROM AUTHOR]

Thin-film composite (TFC) membranes are generally preferred over integrally skinned asymmetric (ISA) membranes in pressure retarded osmosis (PRO) process due to their much higher water permeability, but they cannot operate in the active layer facing feed solution (AL-FS) orientation because of potential delamination of the rejection layer under the high applied pressure. However, operating under AL-FS orientation is preferred as a strategy for better fouling control. Hence, in this study, three ISA hollow fiber membranes were fabricated using a dry-jet wet-spinning method, followed by chemical cross-linking to obtain membranes for PRO application. The best-performing membrane was subjected to fouling test in two orientations. Our results demonstrate that the AL-FS orientation is better for a sustainable long-term PRO operation, given the stable performance throughout the two-day testing. Also, the current use of power density per membrane area as a performance benchmark may not be practical for large-scale PRO operation, and the volumetric power density per module is more relevant. In terms of volumetric power density for a hypothetical 5-in. module, our best-performing membrane is predicted to generate a 3.6 to 10 times better power density than commercial modules, rendering our ISA hollow fiber membranes promising for scaling-up to bigger modules. [Display omitted] • Operating under AL-FS orientation is preferred as a strategy for better fouling control. • Integrally skinned asymmetric hollow fiber membranes were developed for AL-FS orientation in PRO. • The membranes achieved sustainable power production when wastewater was employed. • The volumetric power density was predicted to yield promising solution for practical application. [ABSTRACT FROM AUTHOR]

Abstract: This research focused on combined organic–inorganic fouling and cleaning studies of forward osmosis (FO) membranes. Various organic/inorganic model foulants such as sodium alginate, bovine serum albumin (BSA) and silica nanoparticles were applied to polyamide-polyethersulfone FO hollow fiber membranes fabricated in our laboratory. In order to understand all possible interactions, experiments were performed with a single foulant as well as combinations of foulants. Experimental results suggested that the degree of FO membrane fouling could be promoted by synergistic effect of organic foulants, the presence of divalent cations, low cross-flow velocity and high permeation drag force. The water flux of fouled FO hollow fibers could be fully restored by simple physical cleaning. It was also found that hydrodynamic regime played an important role in combined organic–inorganic fouling of FO membranes. [Copyright &y& Elsevier]

Abstract: The performance of a forward osmosis (FO) system may be characterised by the assessment parameters: FO–RO flux ratio (J w/J w(RO)), apparent FO water permeability (J w/(π ds − π ml)), and the newly developed flux efficiency factor (J w,ob/J w,re). The former two parameters offer information on extent of internal concentration polarisation and driving force utilisation, respectively. The J w,ob/J w,re factor has practical relevance, and reveals the inevitable trade-off between flux and recovery (φ) for a FO system. The derived J w,ob/J w,re factors corresponded well to experimental observations. High water permeability, low salt-to-water permeability ratio, and large mass transfer coefficient improve the performance of a FO system, but these may also be influenced by operational and fouling effects, such as draw solute transmission, fouling resistance and cake-enhanced concentration polarisation. It was shown that membrane properties also play a significant role in fouling behaviour. Fouling amelioration factors include aeration and osmotic backwash. A thin-film composite membrane showed potential for FO application with favourable intrinsic transport parameters. It was demonstrated that a FO system could achieve stable water production with both relatively high flux efficiency (J w,ob/J w,re =0.8) and high recovery (φ =95.8%), which attested to the technology potential. [Copyright &y& Elsevier]