Search

The automobile industry uses magnesium for load-bearing components due to its low density, durability, and ductility. This study investigated a nanocomposite containing Nb2O5 (3 and 6 wt%) nanoparticles as reinforcement with AZ31 magnesium alloy made by stir casting. A severe plastic deformation was conducted on the cast samples via equal-channel angular pressing (ECAP) after homogenization at 410 °C for 24 h and aging at 200 °C for 10 h. The microstructural distributions and mechanical properties of the magnesium metal matrix composites (MMCs) reinforced with Nb2O5 nanoparticles were investigated via ECAP. With the increase in the number of ECAP passes, the grain sizes became uniform, and the size of secondary phases reduced in the pure Nb2O5/AZ31 MMC. The grain size decreased remarkably after the ECAP process from 31.95 µm to 18.41µm due to the dynamic recrystallization during plastic deformation. The mechanical properties of hardness, ultimate tensile strength, and elongation effectively improved after each ECAP pass. The maximum values achieved for the Nb2O5/AZ31 composite subjected to ECAP were 64.12 ± 12 HV, 151.2 MPa, and 52.71%. [ABSTRACT FROM AUTHOR]

Magnesium is the lightest metal and is extensive in the structural application. The metal matrix composites are developed to improve the strength of magnesium alloys. In this research, AZ91 alloy reinforced with 1 wt% WS 2 was produced using stir casting process. The composite was homogenized for 24 h at 410 °C and subsequently aged for 10 h at 200 °C. The severe plastic deformation was performed using equal channel angular pressing (ECAP). The phase composition was analyzed using X-ray diffraction techniques. The microstructure, fractography, and mechanical properties of ECAPed composites have been investigated using scanning electron microscope, and universal testing machines, respectively. The results indicate that B-phases are present in the form of particles inside and at grain boundaries in annealed composites, which are refined to needle-shaped precipitates at grain boundaries, and grains size is refined to 0.2 μm after 4passes of ECAP. Microhardness and tensile yield strength are proportional to the number of passes, and 20.45% and 103.5% are increased respectively after 4pass. The UTS was found to be maximum (324.8 MPa) for 4P WS 2 /AZ91. Fractography analysis revealed that plastic fracture in annealed and elastic-plastic fracture occurred after 4P WS 2 /AZ91 MMC. • WS 2 /AZ91 (MMCs) were manufactured by stir casting method and subsequently annealed are deformed by ECAP. • ECAP effects on microstructure and mechanical behavior of WS 2 /AZ91 MMCs have been investigated. • The relation between number of passes and strength has been established. • The investigations reveal that 4pass-WS 2 /AZ91 exhibits maximum hardness and ultimate tensile strength. [ABSTRACT FROM AUTHOR]

AZ91 reinforced with four different concentrations (0,0.3,0.6,1)wt% of WS 2 micro particles were fabricated using stir casting method. The samples were deformed by equal channel angular pressing (ECAP) after homogenization. The scanning electron microscopy and X-ray diffraction were used to investigate the microstructure and phase composition respectively. The results reveal that rod-like precipitates produced during the homogenization process are refined and bounded in the grain boundaries by the combined effect of WS 2 enrichment and increasing number of passes of ECAP. The needle precipitates are eminent in 1pass 0.3 wt%WS 2 /AZ91. The β-Mg 17 Al 12 and extracted Al particles are dissolved and secondary phases are produced by dynamic recrystallization after 2pass 1 wt%WS 2 /AZ91. The maximum crystallite size and microstrain distribution have been observed for 1pass 0.6 wt%WS 2 /AZ91. The mechanical properties investigation represents that 2pass 0.6 wt%WS 2 /AZ91 has optimal yield strength and ultimate tensile strength. The (22.143)%, (44.735)% and (92) % increment in yield strength, ultimate tensile strength and elongation have been observed in 2pass 1 wt%WS 2 /AZ91 compared with homogenized monolithic AZ91 alloy respectively. The maximum young's modulus (6696.218MPa) has been found for 1pass homogenized WS2/AZ91 and minimum (4108.165MPa) for homogenized 0.6 wt%WS 2 /AZ91. The ECAP deformed 1pass 0.3 wt%WS 2 /AZ91 exhibits the maximum strain hardening rate. The YTS, UTS, and elongation are (30.41) %, (47.6) % and (51.9)% increased after 2pass-0.6 wt%WS 2 /AZ91. [ABSTRACT FROM AUTHOR]