Search

A phase field model enhanced with the shared memory parallelism OpenMP was proposed, capable of modeling the impact of a heavy metal droplet under practical plasma spraying conditions. The finite difference solution of the Navier-Stokes equations, coupled with the Cahn-Hilliard equation, tracks the gas-liquid interface. The liquid fraction, defined over the computational domain, distinguishes fluid from solid. The model is employed for Ni and YSZ drop impacts after ruling out the effect of mesh size. The model exhibits a reasonable parallel-computing efficiency, and the predicted maximum spread factors agree well with analytical models. [ABSTRACT FROM AUTHOR]

• The solution of the Cahn-Hilliard equation to track moving boundaries. • A heat source term added in energy equation to trace solidification profile. • Thermal contact resistance studied to find its effect on maximum spread factor. • A supersonic impact of ceramic particles examined. A modified phase-field three-dimensional model has been developed to simulate the spreading of an impacting droplet undergoing solidification. The model is based on the numerical solution of the Cahn-Hilliard equation coupled with the Navier-Stokes equations for fluid flow and the energy balance equation for heat transfer. The solidification profile is tracked by treating the latent heat as a source term in the energy equation, which is modified to work with the Cahn-Hilliard equation. To verify the model, five cases were tested and matched well with experiments. Also, the effect of thermal contact resistance on the maximum spread factor of a solidifying droplet is discussed. One case was taken from practical thermal spraying conditions where a solidifying ceramic droplet spreads on a cold surface at a supersonic impact velocity; computed results are consistent with available measurements. [ABSTRACT FROM AUTHOR]

Successive impingement of droplets after refining in supersonic plasma jet generally yields a submicron-sized lamellar coating with excellent comprehensive properties. Nevertheless, physical insight into the flattening and rapid solidification with crystallization behavior of supersonic impingement of refined droplets is difficult to understand. In this research, the content of refinement droplets reached 90% and displayed the multi-scale distribution of equiaxed grains. The boundary migration of equiaxed grains and anisotropic coalescence was found in the dynamic temperature gradient. Furthermore, an optimized model was established in order to accurately reproduce the multi-physical coupling process of supersonic impingement of single or two refined droplets, which was based on the numerical calculation of nonlinear equations (including the Mass and momentum, energy balance, Cahn–Hilliard, phase-field and orientational field equations). The size distribution and growth orientation of columnar grains within single or two flattened droplets were in good agreement with the experimental results. Epitaxial growth of columnar grains was found in the two-flattened droplet interface during the extremely rapid cooling stage. This optimized model could be an effective method in predicting the flattening and solidification with crystallization behavior of droplets during plasma spraying. [ABSTRACT FROM AUTHOR]

• Sequential droplet impact with grain growth and impingement is modelled. • Typical velocities of crystal growth are within 2 m/s. • Solidification time of a single splat on a stainless steel substrate is about 0.5 μs. • The undercooling in crystal growth ranges approximately from 150 K to 500 K. A coupled CFD and diffuse interface model was developed to predict the dynamic process of solidification microstructure formation of sequential yttria-stabilized zirconia (YSZ) droplet impact under supersonic plasma spraying. The numerical model relies on the explicit finite difference solution of the Navier-Stokes and energy balance equations, coupled with the Cahn-Hilliard equation, to track liquid-gas interface, and of a phase field model for solidification microstructure formation involving polycrystalline growth to trace solid-liquid interface. Extensive simulations, differing in the status of the first droplet and the impacting parameters of the second one, were carried out. The results reveal that solidification microstructure still follows a columnar pattern if the second droplet lands on the first that is just starting spreading, and that the growth direction around the contact region in the second splat will be obviously skewed by fluid flow if the first has been solidified, owing to earlier and easier nucleation on the top surface of the first splat, thus confirming the epitaxial growth across the splat-splat interface. Computed results are also compared with thermal spray experiments, with gratifying agreement obtained. [ABSTRACT FROM AUTHOR]

• The solution of the Cahn-Hilliard equation to track moving liquid-gas boundaries. • A phase field model for polycrystalline growth used to track solid-liquid interface and grain boundaries. • Supersonic YSZ droplet impact considered. • Convection effect on solidification microstructure investigated. A comprehensive numerical model has been developed, which is capable of representing the impact and spreading of a high-velocity yttria-stabilized zirconia (YSZ) molten droplet with microstructure formation in plasma thermal spraying processes. The numerical model entails the explicit finite difference solution of the Navier-Stokes equations and the energy balance equations, coupled with the Cahn-Hilliard equation to track the liquid-gas two phase interface and with a phase field model for solidification microstructure formation involving the polycrystalline growth. Numerical model procedures are given. The model, after being checked for mesh-independence, was applied to study the spreading and solidification of a high-temperature high-velocity YSZ droplet impinging upon a preheated substrate surface under the conditions typical of supersonic plasma thermal spraying processes. Extensive numerical simulations were carried out and results reveal that the solidification microstructure formed in the spreading droplet consists primarily of columnar grains. Computed results are also compared with thermal spray experiments, and gratifying agreement is obtained. [ABSTRACT FROM AUTHOR]