Search

Using cheap and green lignin as a partial substitute for petroleum-based polyols is highly attractive for sustainable development of polyurethane elastomers (LPUes). However, the traditional synthesis process of LPUes inevitably uses toxic solvents that are difficult to remove or carcinogenic. Here, we reported a solvent-free synthesis method to prepare lignin-containing polyurethane elastomers (SF-LPUes) with high strength, high toughness and high elasticity. Most of the hydroxyl groups of lignin reacted with isocyanates to form a strong chemical cross-linking network, while the unreacted ones formed a dynamic hydrogen bond network with polyurethane matrix, contributing to the in-situ formation of lignin nanoparticles to build a nano-micro phase separation structure. Consequently, a dual-crosslinking network structure was formed and endowed SF-LPUes with excellent mechanical properties. Especially, the SF-LPUes prepared from low molecular alkali lignin possessed a tensile strength as high as 38.2 MPa, a maximum elongation at break of 1108 %, and an elastic recovery ratio of up to 98.7 %. Moreover, SF-LPUes showed impressing reprocessing performance and aging resistance. This work provides an industrial application prospect for the synthesis of lignin-containing polyurethane elastomers via a solvent-free synthesis process., Competing Interests: Declaration of competing interest The authors declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article. There's no financial/personal interest or belief that could affect our objectivity. Our manuscript was submitted only to the International Journal of Biological Macromolecules. All authors approved the submission., (Copyright © 2022 Elsevier B.V. All rights reserved.)

A lignin-based PU coating was prepared for paper-based green packaging. Two representative diisocyanate were used to prepare the coatings. Due to the rigid aromatic, the physical properties of the TDI system reached the maximum below the lignin content of 40%. The HDI that contains flexible aliphatic chains alleviated the brittleness of coating, and it showed physical advantages when the lignin content was more than 50%. Owing to the high lignin content, the coating presented enhanced thermal stability. After coated with the lignin-based PU coatings, the dry tensile strength of coated paper was improved by 126%. Amazingly, the wet strength was increased from 0.31 to 12.6 MPa with an improvement nearly 40 times. Based on the coordination of lignin, Ag + was introduced into the PU matrix, which imparted the coating with excellent antibacterial ability. The colony forming units of E. coli and S. aureus were both less than 1. However, no inhibition halo was observed, which indicated that the Ag was firmly anchored on the coating and the antibacterial ability is only available when the bacterial contact the coating surface. The lignin-based PU coating with favorable sustainability and properties shows great potential in paper-based green packaging fields., (Copyright © 2021 Elsevier B.V. All rights reserved.)

The present work deals with using thermal aggregation of spray drying to achieve uniform structuring of cellulose nanocrystals (CNC) with carbon nanotubes (CNT), for obtaining rough annular microparticles with hierarchical dual dimensions. The structure and characteristics of CNC are crucial to microparticle assembly and superhydrophobic modification. The polyurethane (PU) was used to enhance the firmness of microparticles, during thermal aggregation. The investigated CNC/CNT/PU microparticles showed excellent separation ability for water-in-oil emulsions. Moreover, an abrasion-resistant superhydrophobic coating that combined fast and intelligent water-removing, electrical-conductive and antibacterial functions was manufactured through simple spray coating, which profited from effective role of CNT in excellent conversion of light to heat, as well as its thermal, electrical conductivity and antibacterial properties., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

Lignin is a good candidate for the polymerization and chemical modification to prepare sustainable chemicals and materials, but a relatively low hydroxyl content becomes an obstacle for the preparation of lignin-based polyurethane (PU) adhesives. In order to improve its reactivity, the acetic acid lignin (AAL) was hydroxymethylated before copolymerized with isocyanate during the preparation of PU adhesives. The hydroxymethylation was carried out in an alkaline formaldehyde solution and it was found that 85 °C is the optimal temperature. On that condition, the free formaldehyde content of the corresponding product HL-6 was as low as 0.32%, while the hydroxymethyl was increased by 189.11% compared with original AAL and reached 2.92 mmol/g. In the polymerization of PU adhesives, the hydroxymethylated lignin with a higher aliphatic hydroxyl content formed a more compact three-dimensional urethane cross-linking network with isocyanate. The mechanical properties and thermal stability of the lignin-based PU adhesive were improved by 15-30 wt% in HL-6, and particularly the tensile strength was increased by 21-41 MPa, which indicated that the hydroxymethylation is an efficient way to enrich the hydroxyl in lignin, and the modified lignin is adequate to partially replace petroleum-based polyols for the preparation of PU adhesives with excellent properties., (Copyright © 2020 Elsevier B.V. All rights reserved.)

In this work, TEMPO-oxidized cellulose nanofibers (TOCNs) were investigated as a green additive to the waterborne polyurethane (WPU) based coating, for improving its mechanical properties. The structure, morphology, mechanical properties and performances of the WPU/TOCNs coating were determined. Results showed that TOCNs had good compatibility to the WPU coating, and significantly enhanced the mechanical properties of the coating. The Halpin-Tsai and Ouali models were used to fit for the Young's modulus of the resulting coating, and good agreements were found between the Ouali model and experimental results when the TOCNs content exceeded the critical percolation threshold (0.7vol% or 1.0wt%). It was also found that the pencil hardness of the coating was improved with the addition of TOCNs. However, AFM and pull-off test revealed the negative effects of the TOCNs addition on the surface roughness and adhesion strength of the coating to the wood surface., (Copyright © 2016 Elsevier Ltd. All rights reserved.)