Search

The Standards Coordinating Body for Gene, Cell, and Regenerative Medicines and Cell-Based Drug Discovery (SCB) supports the development and commercialization of regenerative medicine products by identifying and addressing industry-wide challenges through standards. Through extensive stakeholder engagement, the implementation of rapid microbial testing methods (RMTMs) was identified as a high-priority need that must be addressed to facilitate more timely release of products. Since 2017, SCB has coordinated efforts to develop standards for this area through surveys, weekly meetings, workshops, leadership in working groups and participation in standards development organizations. This article describes the results of these efforts and discusses the current landscape of RMTMs for regenerative medicine products. Based on discussions with stakeholders across the field, an overview of traditional culture-based methods and limitations, alternative microbial testing technologies and current challenges, fit-for-purpose rapid microbial testing and case studies, risk-based strategies for selection of novel rapid microbial test methods and ongoing standards efforts for rapid microbial testing are captured here. To this end, SCB is facilitating several initiatives to address challenges associated with rapid microbial testing for regenerative medicine products. Two documentary standards are under development: an International Organization for Standardization standard to provide the framework for a risk-based approach to selecting fit-for-purpose assays primarily intended for cell and gene therapy products and an ASTM standard guide focused on sampling methods for microbial testing methods in tissue-engineered medical products. Working with the National Institute of Standards and Technology, SCB expects to facilitate the process of developing publicly available microbial materials for inter-laboratory testing. These studies will help collect the data necessary to facilitate validation of novel rapid methods. Finally, SCB has been working to increase awareness of, dialog about and participation in efforts to develop standards in the regenerative medicine field., (Copyright © 2021. Published by Elsevier Inc.)

Nanofiber scaffolds are effective for tissue engineering since they emulate the fibrous nanostructure of native extracellular matrix (ECM). Although electrospinning has been the most common approach for fabricating nanofiber scaffolds, airbrushing approaches have also been advanced for making nanofibers. For airbrushing, compressed gas is used to blow polymer solution through a small nozzle which shears the polymer solution into fibers. Our goals were 1) to assess the versatility of airbrushing, 2) to compare the properties of airbrushed and electrospun nanofiber scaffolds and 3) to test the ability of airbrushed nanofibers to support stem cell differentiation. The results demonstrated that airbrushing could produce nanofibers from a wide range of polymers and onto a wide range of targets. Airbrushing was safer, 10-fold faster, 100-fold less expensive to set-up and able to deposit nanofibers onto a broader range of targets than electrospinning. Airbrushing yielded nanofibers that formed loosely packed bundles of aligned nanofibers, while electrospinning produced un-aligned, single nanofibers that were tightly packed and highly entangled. Airbrushed nanofiber mats had larger pores, higher porosity and lower modulus than electrospun mats, results that were likely caused by the differences in morphology (nanofiber packing and entanglement). Airbrushed nanofiber scaffolds fabricated from 4 different polymers were each able to support osteogenic differentiation of primary human bone marrow stromal cells (hBMSCs). Finally, the differences in airbrushed versus electrospun nanofiber morphology caused differences in hBMSC shape where cells had a smaller spread area and a smaller volume on airbrushed nanofiber scaffolds. These results highlight the advantages and disadvantages of airbrushing versus electrospinning nanofiber scaffolds and demonstrate that airbrushed nanofiber scaffolds can support stem cell differentiation., (Published by Elsevier Ltd.)

We have developed a combinatorial method for determining optimum tissue scaffold composition for several X-ray imaging techniques. X-ray radiography and X-ray microcomputed tomography enable non-invasive imaging of implants in vivo and in vitro. However, highly porous polymeric scaffolds do not always possess sufficient X-ray contrast and are therefore difficult to image with X-ray-based techniques. Incorporation of high radiocontrast atoms, such as iodine, into the polymer structure improves X-ray radiopacity but also affects physicochemical properties and material performance. Thus, we have developed a combinatorial library approach to efficiently determine the minimum amount of contrast agent necessary for X-ray-based imaging. The combinatorial approach is demonstrated in a polymer blend scaffold system where X-ray imaging of poly(desaminotyrosyl-tyrosine ethyl ester carbonate) (pDTEc) scaffolds is improved through a controlled composition variation with an iodinated-pDTEc analog (pI(2)DTEc). The results show that pDTEc scaffolds must include at least 9%, 16%, 38% or 46% pI(2)DTEc (by mass) to enable effective imaging by microradiography, dental radiography, dental radiography through 0.75cm of muscle tissue or microcomputed tomography, respectively. Only two scaffold libraries were required to determine these minimum pI(2)DTEc percentages required for X-ray imaging, which demonstrates the efficiency of this new combinatorial approach for optimizing scaffold formulations.

A systematic investigation of tissue engineering scaffolds prepared by salt leaching of a photopolymerized dimethacrylate was performed to determine how the scaffold structure (porosity, pore size, etc.) can be controlled and also to determine how the scaffold structure and the mechanical properties are related. Two series of scaffolds were prepared with (1) the same polymer-to-salt ratio but different salt sizes (ranging from average size of 100 to 390 microm) and (2) the same salt size but different polymer-to-salt ratios (ranging from salt mass of 70 to 90%). These scaffolds were examined to determine how the fabrication parameters affected the scaffold morphometric parameters and corresponding mechanical properties. Combined techniques of X-ray microcomputed tomography (microCT), mercury porosimetry, and gravimetric analysis were used to determine the scaffold parameters, such as porosity, pore size, and strut thickness and their size distributions, and pore interconnectivity. Scaffolds with porosities ranging from 57% to 92% (by volume) with interconnected structures could be fabricated using the current technique. The porosity and strut thickness were subsequently related to the mechanical response of the scaffolds, both of which contribute to the compression modulus of the scaffold. The current study shows that the structure and properties of the scaffold could be tailored by the size and the amount of porogen used in the fabrication of the scaffold.

Model tissue engineering scaffolds based on photocurable resin mixtures with sodium chloride have been prepared for optical imaging studies of cell attachment. A photoactivated ethoxylated bisphenol A dimethacrylate was mixed with sieved sodium chloride (NaCl) crystals and photocured to form a cross-linked composite. Upon soaking in water, the NaCl dissolved to leave a porous scaffold with desirable optical properties, mechanical integrity, and controlled porosity. Scaffolds were prepared with salt crystals that had been sieved to average diameters of 390, 300, 200, and 100 microm, yielding porosities of approximately 75 vol %. Scanning electron microscopy and X-ray microcomputed tomography confirmed that the pore size distribution of the scaffolds could be controlled using this photocuring technique. Compression tests showed that for scaffolds with 84% (by mass fraction) salt, the larger pore size scaffolds were more rigid, while the smaller pore size scaffolds were softer and more readily compressible. The prepared scaffolds were seeded with osteoblasts, cultured between 3 and 18 d, and examined using confocal microscopy. Because the cross-linked polymer in the scaffolds is an amorphous glass, it was possible to optically image cells that were over 400 microm beneath the surface of the sample.

Abstract: Cells are known to sense and respond to the physical properties of their environment and those of tissue scaffolds. Optimizing these cell–material interactions is critical in tissue engineering. In this work, a simple and inexpensive combinatorial platform was developed to rapidly screen three-dimensional (3D) tissue scaffolds and was applied to screen the effect of scaffold properties for tissue engineering of bone. Differentiation of osteoblasts was examined in poly(ethylene glycol) hydrogel gradients spanning a 30-fold range in compressive modulus (≈10 kPa to ≈300 kPa). Results demonstrate that material properties (gel stiffness) of scaffolds can be leveraged to induce cell differentiation in 3D culture as an alternative to biochemical cues such as soluble supplements, immobilized biomolecules and vectors, which are often expensive, labile and potentially carcinogenic. Gel moduli of ≈225 kPa and higher enhanced osteogenesis. Furthermore, it is proposed that material-induced cell differentiation can be modulated to engineer seamless tissue interfaces between mineralized bone tissue and softer tissues such as ligaments and tendons. This work presents a combinatorial method to screen biological response to 3D hydrogel scaffolds that more closely mimics the 3D environment experienced by cells in vivo. [Copyright &y& Elsevier]

Abstract: We have developed a bioreactor-based millifluidic technique that allows for dynamic culture conditions and measurement of the fluid flow impinging upon a three-dimensional tissue engineering scaffold. Chondrocytes in scaffolds have been shown to require mechanical stimulation to produce an extracellular matrix that resembles native cartilage. This study investigates the effect of pulsatile flow on chondrocyte response in a model poly(ethylene glycol) dimethacrylate hydrogel. Bovine chondrocytes were encapsulated in the hydrogel and cultured for 7, 14 and 21 days at pulsatile flow frequencies of 0.5 Hz (15ml/min) and 1.5Hz (17ml/min). The scaffolds cultured under dynamic conditions were compared to those cultured under static (non-flow) conditions. Quantitative real-time reverse transcription polymerase chain reaction was used to quantify collagen type I, collagen type II and aggrecan gene copy numbers as markers for chondrocyte phenotypic expression. Histological sections stained with hematoxylin & eosin, and Alcian blue confirmed chondrocyte morphology and matrix formation. Interestingly, regulation of the collagen type II gene was particularly sensitive to the flow conditions. The understanding of the cell response to encapsulation and flow could be used to identify the appropriate culture conditions necessary to design and develop hydrogel carriers to promote the formation of extracellular matrix as well as to further our knowledge of chondrocyte mechanobiology. [Copyright &y& Elsevier]