Search

Early fault detection and diagnosis of grid-connected photovoltaic systems (GCPS) is imperative to improve their performance and reliability. Low-cost edge devices have emerged as innovative solutions for real-time monitoring, reducing latency, and improving response times. In this work, a lightweight Convolutional Neural Network (CNN) is designed and fine-tuned using Energy Valley Optimizer (EVO) for fault diagnosis. The CNN input consists of two-dimensional scalograms generated using Continuous Wavelet Transform (CWT). The proposed diagnosis technique demonstrated superior performance compared to benchmark architectures, namely MobileNet, NASNetMobile, and InceptionV3, achieving higher test accuracies and lower losses on binary and multi-fault classification tasks on balanced, unbalanced, and noisy datasets. Further, a quantitative comparison is conducted with similar recent studies. The obtained results indicate good performance and high reliability of the proposed fault diagnosis method. [ABSTRACT FROM AUTHOR]

This paper presents a comparative study between four techniques recently used to improve the wind energy conversion system (WECS) to water pumping systems. The WECS is a renewable energy source which has developed rapidly in recent years. The use of the WECS in the water pumping field is a free solution (economically) compared to the use of the electricity grid supply. The control of WECS, equipped with a permanent magnet synchronous generator, has the objective of carefully maximising power generation. A comparative study between the proposed Fuzzy Logic Control, optimised using a genetic algorithm and particle swarm optimisation algorithm, and the conventional Perturb and Observe MPPT method using Matlab/Simulink, is presented. The performance of the proposed system has been verified against the generated output voltage, current and power waveforms, intermediate circuit voltage waveform, and generator speed. The presented results demonstrate the effectiveness of the control strategy applied in this work. [ABSTRACT FROM AUTHOR]

In the present work, we report on theoretical studies of thermodynamic properties, structural and dynamic stabilities, dependence of unit-cell parameters and elastic constants upon hydrostatic pressure, charge carrier effective masses, electronic and optical properties, contributions of interband transitions in the Brillouin zone of the novel Tl2HgGeSe4 crystal. The theoretical calculations within the framework of the density-functional perturbation theory (DFPT) are carried out employing different approaches to gain the best correspondence to the experimental data. The present theoretical data indicate the dynamical stability of the title crystal and they reveal that, under hydrostatic pressure, it is much more compressible along the a-axis than along the c-axis. Strikingly, the charge effective mass values ( m e ∗ and m h ∗ ) vary considerably when the high symmetry direction changes indicating a relative anisotropy of the charge-carrier’s mobility. Furthermore, the Young modulus and compressibility are characterized by the maximum and minimum values ( E max and E min ) and ( β max and β min ) that are equal to (62.032 and 28.812) GPa and (13.672 and 6.7175) TPa–1, respectively. Additionally, we have performed calculations of the Raman spectra (RS) and reached a good correspondence with the experimental RS spectra of the Tl2HgGeSe4 crystal. The XPES associated to RS constitutes powerful techniques to explore the oxidized states of Se and Ge in Tl2HgGeSe4 system. [ABSTRACT FROM AUTHOR]

One crucial objective of this article is to present simplified and accurate approaches to study the current distribution and ground surface potential around the area surrounding an earthed and isolated system in case of a line‐to‐earth fault. The present study is done in the case of uniform and two‐layer soils. Suggested models for calculating the distribution of the earth's surface current density, step, and touch voltages in grounded and isolated systems are presented, discussed, and adapted. The contact and arc resistances of line to ground faulty conductors are considered. Rods and/or grounding grids usually do grounded systems. The impact of both step and touch potentials and current density are investigated in this article. The methods of the calculations are based on the electrical concepts, the charge simulation method, and the imaging procedure for the grounding system. The suggested method can be considered a novel and simple technique for calculating the current distributions of the ground surface during line to ground fault. The results agree with those obtained by others, with the advantage of the proposed algorithm for its ease of application and simplicity. 3‐D dimensions' contours of the current density and the electric potential on the earth surface around the faulty point are presented in case of homogeneous and two layers' soil. Finally, this article's novelty is to devise a method for calculating the step and touch potentials and current density around the point of contact of the conductor carrying the electric voltages in the event of faults occurring in the electrical network, whether the network is grounded or isolated. Such faults of electrical networks may cause human hazards. [ABSTRACT FROM AUTHOR]

This paper proposes an innovative approach to improve the performance of grid-connected photovoltaic (PV) systems operating in environments with variable atmospheric conditions. The dynamic nature of atmospheric parameters poses challenges for traditional control methods, leading to reduced PV system efficiency and reliability. To address this issue, we introduce a novel integration of fuzzy logic and sliding mode control methodologies. Fuzzy logic enables the PV system to effectively handle imprecise and uncertain atmospheric data, allowing for decision-making based on qualitative inputs and expert knowledge. Sliding mode control, known for its robustness against disturbances and uncertainties, ensures stability and responsiveness under varying atmospheric conditions. Through the integration of these methodologies, our proposed approach offers a comprehensive solution to the complexities posed by real-world atmospheric dynamics. We anticipate applications in grid-connected PV systems across various geographical locations and climates. By harnessing the synergistic benefits of fuzzy logic and sliding mode control, this approach promises to significantly enhance the performance and reliability of grid-connected PV systems in the presence of variable atmospheric conditions. On the grid side, both PSO (Particle Swarm Optimization) and GA (Genetic Algorithm) algorithms were employed to tune the current controller of the PI (Proportional-Integral) current controller (inverter control). Simulation results, conducted using MATLAB Simulink, demonstrate the effectiveness of the proposed hybrid MPPT technique in optimizing the performance of the PV system. The technique exhibits superior tracking efficiency, achieving a convergence time of 0.06 s and an efficiency of 99.86%, and less oscillation than the classical methods. The comparison with other MPPT techniques highlights the advantages of the proposed approach, including higher tracking efficiency and faster response times. The simulation outcomes are analyzed and demonstrate the effectiveness of the proposed control strategies on both sides (the PV array and the grid side). Both PSO and GA offer effective methods for tuning the parameters of a PI current controller. According to considered IEEE standards for low-voltage networks, the total current harmonic distortion values (THD) obtained are considerably high (8.33% and 10.63%, using the PSO and GA algorithms, respectively). Comparative analyses with traditional MPPT methods demonstrate the superior performance of the hybrid approach in terms of tracking efficiency, stability, and rapid response to dynamic changes. [ABSTRACT FROM AUTHOR]

This paper discusses the impact of the feature input vector on the performance of dissolved gas analysis-based intelligent power transformer fault diagnosis methods. For this purpose, 22 feature vectors from traditional diagnostic methods were used as feature input vectors for four tree-based ensemble algorithms, namely random forest, tree ensemble, gradient boosted tree, and extreme gradient tree. To build the proposed diagnostics models, 407 samples were used for training and testing. For validation and comparison with the existing methods of literature, 89 samples were used. Based on the results obtained on the training and testing datasets, the best performance was achieved with feature vector 16, which consists of the gas ratios of Rogers' four ratios method and the three ratios technique. The test accuracies based on these vectors are 98.37, 96.75, 95.93, and 97.56% for the namely random forest, tree ensemble, gradient boosted tree, and extreme gradient tree algorithms, respectively. Furthermore, the performance of the methods based on best input feature was evaluated and compared with other methods of literature such as Duval triangle, modified Rogers' four ratios method, combined technique, three ratios technique, Gouda triangle, IEC 60599, NBR 7274, the clustering method, and key gases with gas ratio methods. These methods suffer from unreliability, and this is the motivation behind the current work to develop a new technique that enhances the diagnostic accuracy of transformer faults to avoid unwanted faults and outages from the network. On validating dataset, diagnostic accuracies of 92.13, 91.01, 89.89, and 91.01% were achieved by the namely random forest, tree ensemble, gradient boosted tree, and extreme gradient tree models, respectively. These diagnostic accuracies are higher than 83.15% for the clustering method, 82.02% for the combined technique, 80.90% for the modified IEC 60599, and 79.78% for key gases with gas ratios, which are the best existing methods. Even if the performance of dissolved gas analysis-based intelligent methods depends strongly on the shape of the feature vector used, this study provides scholars with a tool for choosing the feature vector to use when implementing these methods. [ABSTRACT FROM AUTHOR]

Series arc fault is the main cause of electrical fire in low-voltage distribution system. A fast and accurate detection system can reduce the risk of fire effectively. In this paper, series arc experiment is carried out for different kinds of electrical load. The time-domain current is analyzed by Morlet wavelet. Then, the multiscale wavelet coefficients are expressed as the coefficient matrix. In order to meet the data dimension requirements of neural networks, a color domain transformation method is used to transform the feature matrix into an image. A regularization method based on gamma transform is proposed for small sample data sets. The results showed that the proposed regularization method improved the validation set accuracy of ResNet50 from 66.67% to 96.53%. The overfitting problem of neural network was solved. In addition, this method fused fault features of 64 different scales, and provided a valuable manually labeled arc fault dataset. Compared with the threshold detection method, this method was more objective. The use of image features increased intuitiveness and generality. Compared with other typical lightweight networks, this method had the best detection performance. [ABSTRACT FROM AUTHOR]

This paper outlines the development of a high-performance maximum power point tracking (MPPT)-based solar irradiance estimator for photovoltaic (PV) systems. The suggested estimator is constructed around a simple current–voltage-based algebraic equation that hinges on the operation of the PV system at its maximum power point (MPP). In the realm of MPP operation, the overall system is driven by a nonlinear MPPT controller. To achieve this function, we integrated a hybrid incremental conductance integral backstepping (H-INC-IBS) controller to effectively regulate the PV system. This controller was specially chosen for its powerful potency in maximizing the dynamics of the PV system, leading to heightened robustness against changing environmental conditions. The simulation results are provided to showcase the suitability of the proposed estimator. Furthermore, the estimator was verified under experimental conditions, highlighting its soundness and practicality. Through evaluations and comparisons with the conventional irradiance estimator, this paper aimed to emphasize the superiority of the proposed solar irradiance estimator in providing more accurate estimations of solar irradiance for PV systems operating under MPPT supervision. [ABSTRACT FROM AUTHOR]

A photovoltaic emulator (PVE) is a specialized device designed to mimic the static and dynamic properties of a solar panel. It serves as a crucial tool for testing and validating PV systems. Despite the unpredictable variations in real environmental conditions, the PVE offers a controlled environment, facilitating the smooth implementation and testing of PV subsystems. The PVE consists of two essential components: the reference PV model and the PVE power electronics controller. For simplicity, both these elements must be inherently straightforward. Numerous advanced methods have been proposed in the literature to efficiently integrate the PV model into the PVE system. However, these approaches often involve complex iterative computations of intricate equations related to solar panels, making them less practical. To address these limitations, this paper introduces a novel PVE that aims to simplify the implementation and integration of the PV model. The proposed system employs a simple and non-iterative approach to provide the reference to the PVE, using a straightforward explicit model of the solar panel. In comparison to existing works, the proposed PVE stands out for its high flexibility and simplicity as it does not require the complex iterative computations of implicit equations related to the solar panel model. The overall PVE system is implemented with a basic proportional-integral (PI) controller and a DC-DC buck power electronic converter. It is then validated using a 200 W solar panel through a series of experiments, including the EN 50530 Test. The results of these experiments demonstrate that the proposed PVE efficiently reproduces the static and dynamic characteristics of a solar panel. [ABSTRACT FROM AUTHOR]

This article proposes an enhanced quasi-reflection jellyfish optimization (QRJFO) algorithm for solving the optimal power flow (OPF) problem. The multi-dimension objective functions are the fuel costs, transmission losses and pollutant emissions. Despite the simple structure of the jellyfish optimization algorithm, it requires significant exploitation and exploration control characteristics to support its capability. In the proposed QRJFO, a cluster is chosen randomly for every jellyfish from the population to reflect the social group that shares information in it. It varies from one to the next. The exploration phase is supported by introducing quasi-opposition-based learning. The performance of the proposed QRJFO algorithm is evaluated on the IEEE 57-bus, practical West Delta Region system and large-scale IEEE 118 bus. The simulation results demonstrate the quality of the solution and resilience of QRJFO. It is very significant for operating power systems from economic, technical and environmental perspectives. [ABSTRACT FROM AUTHOR]

Classification of electroencephalogram (EEG) signals for humans can be achieved via artificial intelligence (AI) techniques. Especially, the EEG signals associated with seizure epilepsy can be detected to distinguish between epileptic and non-epileptic regions. From this perspective, an automated AI technique with a digital processing method can be used to improve these signals. This paper proposes two classifiers: long short-term memory (LSTM) and support vector machine (SVM) for the classification of seizure and non-seizure EEG signals. These classifiers are applied to a public dataset, namely the University of Bonn, which consists of 2 classes –seizure and nonseizure. In addition, a fast Walsh-Hadamard Transform (FWHT) technique is implemented to analyze the EEG signals within the recurrence space of the brain. Thus, Hadamard coefficients of the EEG signals are obtained via the FWHT. Moreover, the FWHT is contributed to generate an efficient derivation of seizure EEG recordings from non-seizure EEG recordings. Also, a k-fold cross-validation technique is applied to validate the performance of the proposed classifiers. The LSTM classifier provides the best performance, with a testing accuracy of 99.00%. The training and testing loss rates for the LSTM are 0.0029 and 0.0602, respectively, while the weighted average precision, recall, and F1-score for the LSTM are 99.00%. The results of the SVM classifier in terms of accuracy, sensitivity, and specificity reached 91%, 93.52%, and 91.3%, respectively. The computational time consumed for the training of the LSTM and SVM is 2000 and 2500 s, respectively. The results show that the LSTM classifier provides better performance than SVM in the classification of EEG signals. Eventually, the proposed classifiers provide high classification accuracy compared to previously published classifiers. [ABSTRACT FROM AUTHOR]