Search

As-cast binary Al–Si alloys containing ∼8, 12, 20, and 30 wt.% Si, representing the hypoeutectic, eutectic (12 wt.% Si), and hypereutectic compositions, were subjected to severe plastic deformation by friction stir processing (FSP) for grain refinement to 2.3–2.7 μm by dynamic recrystallization. Tensile tests conducted by differential strain rate test technique over the strain rates of 10−4 – 10−2 s−1 and test temperatures in the range of ∼840–530 K led to strain rate sensitivity index (m) varying from ∼0.04 to 0.40 depending on temperature, strain rate, and alloy composition. The constant initial strain rate tests conducted at 10−4 s−1 and 840 K exhibited a maximum elongation of 250% in the hypereutectic Al–20Si alloy, but the same increased linearly with m irrespective of alloy composition. Generally, with increasing Si content, the activation energy for deformation increased from 104.7 ± 14.4 kJ/mol for eutectic Al–12Si to 310.4 ± 32.3 kJ/mol for hypereutectic Al–30Si, which increased further to 572 ± 148 kJ/mol over the higher temperature range of 840–800 K. Analysis of observed deformation and microstructure behaviour supports the occurrence of superplasticity, whereby the accommodation of grain boundary sliding by grain boundary migration led to enhanced grain growth or else the local high-stress concentration at the particle-matrix interface led to cavity formation. There was no evidence of dynamic recrystallization during high-temperature tensile deformation but the flow softening observed is ascribed to the occurrence of concurrent cavitation. [ABSTRACT FROM AUTHOR]

In large buildings, effective load shedding and shifting and providing the maximum power through solar renewable sources remain challenges because of users' unpredictable load consumption. Conventionally, load shifting, load shedding, and load covering are majorly dependent on user inputs. The lack of user interest in participating in demand responses for effective load shifting and covering remains a problem. Effective load covering through renewables and user-friendly load shedding and shifting with maximized user participation are challenging and demand high-resolution user load consumption information, which are not possible without sophisticated communication and digital twins. In this research work, a novel fuzzy-logic-based cascaded decentralized load-controlling mechanism has been developed that manages the residential building load through load-shifting, load-covering, and load-shedding schemes without any communication protocols and digitization between residential units. The decentralized controller aims to effectively utilize the centralized resources of power generation with the effective automated participation of users. The quantification of the load shifting, covering, and shedding performed during peak hours was well covered under the load-covering scheme, and the results showed that flexibility capacities of 1617 kW were achieved for load covering, 294 kW for load shedding, and 166.34 kW through shifting. A total load of 60 kW, which was reduced during shedding and shifting, was well covered during load covering through renewables. [ABSTRACT FROM AUTHOR]

Power generation from fossil fuels is the biggest challenge in the next half of the century. Alternative power generation techniques such as solar photovoltaic (PV) show potential to act as a future fuel with a challenge to efficiently convert the harvested solar energy into electrical power. This investigation conclusively focused on setting a 2.160-kW solar PV system capable of working at a higher efficiency by developing a mechanical structure that optimizes power production and minimizes energy losses. In addition to that, solar PV system efficiencies at various tracking positions, performance coefficients during rainy and sunny days, and system degradation rates have also been investigated. The PVsyst v6.8 simulation tool was used to obtain the simulated results, which were compared with the actual experimental results. The parameters considered for the investigations include ambient temperature, irradiance, solar PV module surface temperature, solar PV voltage and current, wind velocity, and atmospheric turbidity. The solar PV system was evaluated based on two modes, namely, M1 (no tracking/fixed type) and M2 (manual tracking by changing the position of the solar PV system every hour). The predictive results obtained using PVsyst v6.8 concluded that total energy production from the installed system was 3,242 kWh/yr and 3,984 kWh/yr for M1 and M2, respectively. The performance ratio (PR), obtained from simulation, was 72% and 78% for M1 and M2, respectively, which was consistent with the experimental results, i.e., 70% and 72% for M1 and M2, respectively. Similarly, the power conversion efficiencies under standard temperature and conditions for both modes, simulated and experimental, were found to be 16.50% and 12.75%, respectively. The estimated degradation rate was observed in the range of -0.6% to -5.0%. [ABSTRACT FROM AUTHOR]

Power augmentation in a small-scale horizontal axis wind turbine, with its rotor encased in a flanged diffuser is explored. The power output of the wind turbine varies with changes in the diffuser design and the resulting back pressure. Reduction in this back pressure also results in early flow separation at the diffuser surface, which hinders turbine performance. The main aim of this study is to numerically investigate the local configuration of the wind turbine location inside the diffuser by varying diffuser angles and wind speeds. Therefore, shroud and flange were modeled and analyzed using the computational fluid dynamic (CFD) analyses and experiments were performed at two wind speeds 6 m/s and 8 m/s with and without the diffuser for model validation. The divergence angle of 4° was found to have no flow separation, thus maximizing flow rate. The proposed design shows wind speed improvement of up to 1.68 times compared to the baseline configuration. The corresponding optimum flange height was found to be 250 mm. However, increasing the divergence angle had a similar output. The dimensionless location of wind turbine was found to be between 0.45 and 0.5 for 2° and 4° divergence angle respectively. Furthermore, the maximum augmentation location varies with wind speed and diffuser's divergence angle as described by dimensionless location of wind turbine, thus presenting a noteworthy contribution to the horizontal axis wind turbine area with the flanged diffuser. [ABSTRACT FROM AUTHOR]

Fossil fuels are being depleted, resulting in increasing environmental pollution due to greenhouse gases and, consequently, emerging detrimental environmental problems. Therefore, renewable energy is becoming more important; hence, significant research is in progress to increase efficient uses of solar energy. In this paper, the thermal performance of a conical concentrating system with different heat transfer fluids at varied flow rates was studied. The conical-shaped concentrator reflects the incoming solar radiation onto the absorber surface, which is located at the focal axis, where the collected heat is transported through heating mediums or heat transfer fluids. Distilled water and nanofluids (Al2O3, CuO) were used in this study as the heat transfer fluids and were circulated through the absorber and the heat storage tank in a closed loop by a pump to absorb the solar radiation. The efficiency of the conical concentrating system was measured during solar noon hours under a clear sky. The collector efficiency was analyzed at different flow rates of 2, 4, and 6 L/min. The thermal efficiency, calculated using different heat transfer fluids, were 72.5% for Al2O3, 65% for CuO, and 62.8% for distilled water. Comparing the thermal efficiency at different flow rates, Al2O3 at 6 L/min, CuO at 6 L/min, and distilled water at 4 L/min showed high efficiencies; these results indicate that the Al2O3 nanofluid is the better choice for use as a heating medium for practical applications. [ABSTRACT FROM AUTHOR]