Search

The demand for real-time monitoring of cell functions and cell conditions has dramatically increased with the emergence of organ-on-a-chip (OOC) systems. However, the incorporation of co-cultures and microfluidic channels in OOC systems increases their biological complexity and therefore makes the analysis and monitoring of analytical parameters inside the device more difficult. In this work, we present an approach to integrate multiple sensors in an extremely thin, porous and delicate membrane inside a liver-on-a-chip device. Specifically, three electrochemical dissolved oxygen (DO) sensors were inkjet-printed along the microfluidic channel allowing local online monitoring of oxygen concentrations. This approach demonstrates the existence of an oxygen gradient up to 17.5% for rat hepatocytes and 32.5% for human hepatocytes along the bottom channel. Such gradients are considered crucial for the appearance of zonation of the liver. Inkjet printing (IJP) was the selected technology as it allows drop on demand material deposition compatible with delicate substrates, as used in this study, which cannot withstand temperatures higher than 130 °C. For the deposition of uniform gold and silver conductive inks on the porous membrane, a primer layer using SU-8 dielectric material was used to seal the porosity of the membrane at defined areas, with the aim of building a uniform sensor device. As a proof-of-concept, experiments with cell cultures of primary human and rat hepatocytes were performed, and oxygen consumption rate was stimulated with carbonyl-cyanide-4-(trifluoromethoxy)phenylhydrazone (FCCP), accelerating the basal respiration of 0.23 ± 0.07 nmol s-1/106 cells up to 5.95 ± 0.67 nmol s-1/106 cells s for rat cells and the basal respiration of 0.17 ± 0.10 nmol s-1/106 cells by up to 10.62 ± 1.15 nmol s-1/106 cells for human cells, with higher oxygen consumption of the cells seeded at the outflow zone. These results demonstrate that the approach of printing sensors ins, Peer Reviewed, Postprint (author's final draft)

Inkjet printing has emerged from a digital graphic arts printing technology to become a versatile tool for the patterned deposition of functional materials. This thesis contributes to the research in the area of functional inkjet printing by focusing on two different topics: (i) inkjet printing of colloidal suspensions to study the principles of deposit formation and to develop deposits with photonic properties based on self-assembly, and (ii) the development of a reliable manufacturing process for all-inkjet-printed thin-film transistors, highlighting the importance of selection of materials and inks, print pattern generation, and the interplay between ink, substrate and printing conditions. (i) Colloidal suspensions containing nanospheres were applied as ink formulation in order to study the fundamental processes of layer formation and to develop structures with periodically arranged nanospheres allowing the modulation of electromagnetic waves. Evaporation-driven self-assembly was found to be the main driver for the formation of the final deposit morphology. Fine-tuning of inkjet process parameters allows the deposition of highly ordered structures of nanospheres to be arranged as monolayer, multilayer or even three-dimensional assemblies with a microscopic spherical shape. (ii) This thesis demonstrates the development of a manufacturing process for thin-film transistors based on inkjet printing. The knowledge obtained from the study with the colloidal nanospheres is used to generate homogeneous and continuous thin films that are stacked well-aligned to each other to form transistors. Industrial printheads were applied in the manufacturing process, allowing for the up-scaling of the manufacturing by printing of several thousands of devices, and thus the possibility to study the process yield as a function of printing parameters. The discrete droplet-by-droplet nature of the inkjet printing process imposes challenges on the control of printed patterns. Inkjet print

We report on the detailed electrical investigation of all-inkjet-printed thin-film transistor (TFT) arrays focusing on TFT failures and their origins. The TFT arrays were manufactured on flexible polymer substrates in ambient condition without the need for cleanroom environment or inert atmosphere and at a maximum temperature of 150 °C. Alternative manufacturing processes for electronic devices such as inkjet printing suffer from lower accuracy compared to traditional microelectronic manufacturing methods. Furthermore, usually printing methods do not allow the manufacturing of electronic devices with high yield (high number of functional devices). In general, the manufacturing yield is much lower compared to the established conventional manufacturing methods based on lithography. Thus, the focus of this contribution is set on a comprehensive analysis of defective TFTs printed by inkjet technology. Based on root cause analysis, we present the defects by developing failure categories and discuss the reasons for the defects. This procedure identifies failure origins and allows the optimization of the manufacturing resulting finally to a yield improvement.

We report on the detailed electrical investigation of all-inkjet-printed thin-film transistor (TFT) arrays focusing on TFT failures and their origins. The TFT arrays were manufactured on flexible polymer substrates in ambient condition without the need for cleanroom environment or inert atmosphere and at a maximum temperature of 150 °C. Alternative manufacturing processes for electronic devices such as inkjet printing suffer from lower accuracy compared to traditional microelectronic manufacturing methods. Furthermore, usually printing methods do not allow the manufacturing of electronic devices with high yield (high number of functional devices). In general, the manufacturing yield is much lower compared to the established conventional manufacturing methods based on lithography. Thus, the focus of this contribution is set on a comprehensive analysis of defective TFTs printed by inkjet technology. Based on root cause analysis, we present the defects by developing failure categories and discuss the reasons for the defects. This procedure identifies failure origins and allows the optimization of the manufacturing resulting finally to a yield improvement.

We report about the inkjet printing of multi-walled carbon nanotubes (MWCNTs) for conductive tracks. The MWCNTs were grown by chemical vapor deposition allowing a defined length and diameter. An inkjet-printable ink formulation was prepared by dispersing the MWCNTs in water. Inkjet-printed high resolution patterns were obtained by printing the prepared ink formulation on silicon wafers utilizing evaporation-driven self-assembly processes. After the deposition of the ink, the solvent evaporation induces material flows within the liquid moving the MWCNTs preferably to the edges of the printed patterns as well as to the print starting position where they assemble. Atomic force microscopy (AFM) reveals a preferential orientation of the deposited MWCNTs. The resulting deposit pattern is well-known as coffee-ring effect which is used here to enable high resolution printing and self-ordering of the MWCNTs. Depending on different print parameters such as drop spacing or substrate temperature, conductive track widths in the range of 5-15 mu m were achieved with a electrical resistivity of about 3.9.10(-3) to 5.6.10(-3) Omega.m measured by current-sensitive AFM. (C) 2015 Elsevier Ltd. All rights reserved., Funding Agencies|Deutsche Forschungsgemeinschaft (DFG) [GRK1215, FOR1713, 287682]; Linkoping University, Department of Science and Technology [ITN-2010-00018]; Cluster of Excellence cfaed; COST Action Nanospectroscopy [MP1302]

We report on inkjet printing of aqueous colloidal suspensions containing monodisperse silica and/or polystyrene nanosphere particles and a systematic study of the morphology of the deposits as a function of different parameters during inkjet printing and solvent evaporation. The colloidal suspensions act as a model ink for an understanding of layer formation processes and resulting morphologies in inkjet printing in general. We investigated the influence of the surface energy and the temperature of the substrate, the formulation of the suspensions, and the multi-pass printing aiming for layer stacks on the morphology of the deposits. We explain our findings with models of evaporation-driven self-assembly of the nanosphere particles in a liquid droplet and derive methods to direct the self-assembly processes into distinct one- and two-dimensional deposit morphologies.