Search

As an economical energy recovery device, pump as turbine (PAT) is widely used in micro-hydropower stations and the chemical industry. The inlet and outlet pipelines connected to the double-suction pump are on the same horizontal line. As the pipeline layout is very convenient, in some chemical industries, the way of residual pressure energy utilization is increasing using the double-suction pump as a turbine. Based on numerical simulation, experimental verification, and entropy generation theory, the energy loss rule of each flow component in the pump mode and turbine mode under different flow rates is compared and analyzed. The results show that when the double-suction pump is used as a turbine, the flow rate at the best efficiency point (BEP) in the turbine mode shifts to a large flow rate by 30.89% and the BEP efficiency decreases by 1.30%. In the pump mode and turbine mode, the main energy loss component is the impeller, and the turbulent entropy generation power and the wall entropy generation power are the main sources of energy loss. The energy loss in the suction chamber and impeller increases sharply, and the energy loss is primarily enhanced in the blade trailing edge and the tongue near due to the unsteady flow in the turbine mode. Due to the complex structure, the spiral suction chamber is not suitable for the flow direction of the fluid flow out of the impeller, and the flow state inside the impeller is negatively affected by the suction chamber in the turbine mode. This paper provides a theoretical basis for the design and application of double-suction centrifugal PAT. [ABSTRACT FROM AUTHOR]

We demonstrate an optically tunable mode-locked fiber laser using long-period fiber grating (LPFG) coated with multi-walled carbon nanotubes (CNTs). The multi-walled CNTs can absorb light to convert it into thermal energy, and the resonance wavelength of the grating can be easily turned by varying the external modulated light power. This multi-walled CNT coated LPFG-based all-optical fast and efficient spectrum tunable filter enables continuous tuning of the central wavelength of the laser by manipulating the loss of the mode-locked laser, ensuring the stability of the mode-locking state. In the absence of modulated light on multi-walled CNTs, the soliton laser could generate 890 fs pulses at 1546.7 nm with a spectrum bandwidth of 3.26 nm and a signal-to-noise ratio of 73.1 dB. Through adjustment of the pump power of the modulation light on multi-walled CNTs, the mode-locked fiber laser can be continuously tuned from 1546.71 to 1563.15 nm. The response time of the optically tunable system was measured to be in the order of hundreds of milliseconds. The presented optical tuning filter shows great potential in the fiber laser system, offering a repeatable, straightforward, and rapidly responsive laser tuning technique. [ABSTRACT FROM AUTHOR]

Apart from the polarization and spatial mode, the degree of coherence (DoC), as a new degree of freedom (DoF), has actuated the control of structured optical fields beyond into a higher dimension. However, the control of DoC mainly focuses on the spatial coherence, and so far, there are no reports on the modulation of temporal coherence of the structured light. Here, a temporal coherence-tailorable vector fiber source is proposed and experimentally demonstrated. With a two-mode long-period fiber grating and polarization control, switchable transverse-mode outputs including azimuthally polarized mode TE01 and radially polarized mode TM01 are performed in an all-fiber compact regime. Benefitting from a tunable superfluorescent fiber source as the illumination of spatial mode control, the temporal coherence and the operating wavelength of vector beams can be simultaneously modulated. This work may not only advance a considerable protocol for creating and manipulating high-dimensional vectorial optical field, but also open up a promising avenue for potential applications in optical communication, high-resolution imaging, and particle trapping. [ABSTRACT FROM AUTHOR]

Due to the complex structure of a double-suction pump's suction chamber, the flow in the pump's cavity is often ignored in numerical simulations because of difficulties in structured hexahedral meshing. However, the wear ring clearance interlinking the pump chamber leads the fluid at the impeller inlet directly to the impeller area. This significantly impacts the pump's internal flow field, so the influence of the clearance on the internal flow of a double-suction pump cannot be ignored. This paper develops four three-dimensional double-suction pump models with different wear ring clearances to investigate their influence on pump performance, and structured hexahedral meshes were used for all the computational domains. The clearances varied from 0.2 to 0.5 mm in 0.1 mm increments. The influences of the clearance on the energy loss, external characteristics, and internal flow field distribution of the pump were simulated via a verified computational fluid dynamics method. The results show that the wear ring leakage decreases with the flow rate and increases with wear ring clearance. The increase in backflow leads to an internal flow disorder inside the impeller, resulting in a decreased head and efficiency. Energy loss is mainly caused by increasing the turbulence entropy production with an increasing wear ring clearance. Also, the low-pressure region in the pump cavity expands to the volute with increasing clearance, and the impeller outlet pressure decreases. This study's research on wear ring clearance provides a reference for the design and application of double-suction centrifugal pumps. [ABSTRACT FROM AUTHOR]