Search

Cellular materials offer industries the ability to close gaps in the material selection design space with properties not otherwise achievable by bulk, monolithic counterparts. Their superior specific strength, stiffness, and energy absorption, as well as their multi-functionality, makes them desirable for a wide range of applications. The objective of this paper is to compile and present a review of the open literature focusing on the energy absorption of periodic three-dimensional cellular materials. The review begins with the methodical cataloging of qualitative and quantitative elements from 100 papers in the available literature and then provides readers with a thorough overview of the state of this research field, discussing areas such as parent material(s), manufacturing methods, cell topologies, cross-section shapes for truss topologies, analysis methods, loading types, and test strain rates. Based on these collected data, areas of great and limited research are identified and future avenues of interest are suggested for the continued maturation and growth of this field, such as the development of a consistent naming and classification system for topologies; the creation of test standards considering additive manufacturing processes; further investigation of non-uniform and non-cylindrical struts on the performance of truss lattices; and further investigation into the performance of lattice materials under the impact of non-flat surfaces and projectiles. Finally, the numerical energy absorption (by mass and by volume) data of 76 papers are presented across multiple property selection charts, highlighting various materials, manufacturing methods, and topology groups. While there are noticeable differences at certain densities, the graphs show that the categorical differences within those groups have large overlap in terms of energy absorption performance and can be referenced to identify areas for further investigation and to help in the preliminary design process by researchers and industry professionals alike. [ABSTRACT FROM AUTHOR]

Additive manufacturing of soft magnetic materials is a promising technology for creating topologically optimized electrical machines. High-performance electrical machines can be made from high-silicon-content FeSi alloys. Fe-6.5wt%Si material has exceptional magnetic properties; however, manufacturing this steel with the classical cold rolling methodology is not possible due to the brittleness of this material. Laser powder bed fusion technology (L-PBF) offers a solution to this problem. Finding the optimal printing parameters is a challenging task. Nevertheless, it is crucial to resolve the brittleness of the created materials so they can be used in commercial applications. The temperature dependence of magnetic hysteresis properties of Fe-6.5wt%Si materials is presented in this paper. The magnetic hysteresis properties were examined from 20 °C to 120 °C. The hysteresis measurements were made by a precision current generator–based hysteresis measurement tool, which uses fast Fourier transformation–based filtering techniques to increase the accuracy of the measurements. The details of the applied scalar hysteresis sensor and the measurement uncertainties were discussed first in the paper; then, three characteristic points of the static hysteresis curve of the ten L-PBF-manufactured identical toroidal cores were investigated and compared at different temperatures. These measurements show that, despite the volumetric ratio of the porosities being below 0.5%, the mean crack length in the samples is not significant for the examined samples. These small defects can cause a significant 5% decrement in some characteristic values of the examined hysteresis curve. [ABSTRACT FROM AUTHOR]

The cellular automata (CA) method has played an important role in the research and development of metallic materials. CA can interpret the microstructure changes of materials and obtain more abundant, accurate and intuitive information of microstructure evolution than conventional methods. CA can visually represent the process of grain formation, growth, development and change to us in a graphical way, which can assist us in analysis, thinking and solving problems. In the last five years, the application of CA in materials research has been rapidly developed, and CA has begun to occupy an increasingly important position in the simulation research of metallic materials. After introducing the advantages and limitations of CA compared to other widely used simulation methods, the purpose of this paper is to review the recent application progress on the microstructure simulation of metallic materials using CA, such as solidification, recrystallization, phase transformation and carbide precipitation occurring during forming and heat treatment. Specifically, recent research advances on microstructure simulation by CA in the fields of additive manufacturing, welding, asymmetrical rolling, corrosion prevention, etc., are also elaborated in this paper. Furthermore, this paper points out the future work direction of CA simulation in the research of metallic materials, especially in the simulation of the crystal structure, the prediction of mechanical properties, CA simulation software and rule systems, etc. These are expected to attract wide attention of researchers in the field of metallic materials and promote the development of CA in materials research. [ABSTRACT FROM AUTHOR]

In this review article, we focus on the relationship between permanent magnets and the electric motor, as this relationship has not been covered in a review paper before. With the increasing focus on battery research, other parts of the electric system have been neglected. To make electrification a smooth transition, as has been promised by governing bodies, we need to understand and improve the electric motor and its main component, the magnet. Today's review papers cover only the engineering perspective of the electric motor or the material-science perspective of the magnetic material, but not both together, which is a crucial part of understanding the needs of electric-motor design and the possibilities that a magnet can give them. We review the road that leads to today's state-of-the-art in electric motors and magnet design and give possible future roads to tackle the obstacles ahead and reach the goals of a fully electric transportation system. With new technologies now available, like additive manufacturing and artificial intelligence, electric motor designers have not yet exploited the possibilities the new freedom of design brings. New out-of-the-box designs will have to emerge to realize the full potential of the new technology. We also focus on the rare-earth crisis and how future price fluctuations can be avoided. Recycling plays a huge role in this, and developing a self-sustained circular economy will be critical, but the road to it is still very steep, as ongoing projects show. [ABSTRACT FROM AUTHOR]

This research paper aims to explore the mechanical characteristics of polyamide PA12 (PA12) as a 3D material printed utilizing Selective Laser Sintering (SLS) and HP MultiJet Fusion (HP MJF) technologies in order to design and manufacture forearm orthoses. The study assessed the flowability of the materials used and compared the mechanical performance of PA12 with each other using tensile, flexure, and impact tests in five different fabrication orientations: X, Y, Z, tilted 45° XZ, and tilted 45° YZ. The results of the study provide, firstly—the data for testing the quality of the applied polyamide powder blend and, secondly—the data for the design of the orthosis geometry from the aspect of its strength parameters and the safety of construction. The mechanical parameters of SLS specimens had less variation than MJF specimens in a given orientation. The difference in tensile strength between the 3D printing technologies tested was 1.8%, and flexural strength was 4.7%. A process analysis of the forearm orthoses revealed that the HP MJF 5200 system had a higher weekly production capacity than the EOS P396 in a production variance based on obtaining maximum strength parameters and a variance based on maximizing economic efficiency. The results suggest that medical device manufacturers can use additive manufacturing technologies to produce prototypes and small-batch parts for medical applications. This paper pioneers using 3D printing technology with Powder Bed Fusion (PBF) methods in designing and manufacturing forearm orthoses as a low- to medium-volume product. The applied solution addresses the problem of medical device manufacturers with regard to the analysis of production costs and mechanical properties when using 3D printing for certified medical devices. [ABSTRACT FROM AUTHOR]

In this paper, electroless nickel plating is explored for the protection of binder-jetting-based additively manufactured (AM) composite materials. Electroless nickel plating was attempted on binder-jetted composites composed of stainless steel and bronze, resulting in differences in the physicochemical properties. We investigated the impact of surface finishing, plating solution chemistry, and plating parameters to attain a wide range of surface morphologies and roughness levels. We employed the Keyence microscope to quantitatively evaluate dramatically different surface properties before and after the coating of AM composites. Scanning electron microscopy revealed a wide range of microstructural properties in relation to each combination of surface finishing and coating parameters. We studied chempolishing, plasma cleaning, and organic cleaning as the surface preparation methods prior to coating. We found that surface preparation dictated the surface roughness. Taguchi statistical analysis was performed to investigate the relative strength of experimental factors and interconnectedness among process parameters to attain optimum coating qualities. The quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the roughness of the nickel-plated surface were 17.95%, 8.2%, 50.02%, and 13.21%, respectively. On the other hand, the quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the thickness of nickel plating were 35.12%, 41.40%, 3.87%, and 18.24%, respectively. The optimum combination of the factors' level projected the lowest roughness of Ra at 7.76 µm. The optimum combination of the factors' level projected the maximum achievable thickness of ~149 µm. This paper provides insights into coating process for overcoming the sensitivity of AM composites in hazardous application spaces via robust coating. [ABSTRACT FROM AUTHOR]

This paper deals with the electromagnetic characterization of a laminated toroidal ferromagnetic core made through additive manufacturing, specifically using the laser powder bed fusion process. The continuing demand for increasingly efficient, lightweight, and higher performance electric machines is creating huge challenges in the design and realization of new electric motor solutions. The constant improvements in additive manufacturing technologies have prompted researchers to investigate the possibility of adopting these production techniques for the manufacture of high-value electric motors. For these reasons, this paper investigates the ferromagnetic characteristics of an additively manufactured core made with FeSi6.5 powder. The BH curve and the specific iron losses of the processed material have been measured so that they can be compared with a commercial lamination, and have the possibility of carrying out more precise finite element simulations. [ABSTRACT FROM AUTHOR]

Additive manufacturing is very important due to its potential to build components and products using high-performance materials. The filament-based 3D printing of ceramics is investigated, revealing significant developments and advancements in ceramic material extrusion technology in recent years. Researchers employ several typologies of ceramics and binders to achieve fully dense products. The design of the filament and the necessary technological adaptations for 3D printing are fully investigated. From a material perspective, this paper reviews and analyzes the recent developments in additive manufacturing of material-extruded ceramics products, pointing out the performance and properties achieved with different material-binder combinations. The main gaps to be filled and recommendations for future developments in this field are reported. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) is often used to create designs inspired by topology optimization and biological structures, yielding unique cross-sectional geometries spanning across scales. However, manufacturing defects intrinsic to AM can affect material properties, limiting the applicability of a uniform material model across diverse cross-sections. To examine this phenomenon, this paper explores the influence of specimen size and layer height on the compressive modulus of polycarbonate (PC) and thermoplastic polyurethane (TPU) specimens fabricated using fused filament fabrication (FFF). Micro-computed tomography imaging and compression testing were conducted on the printed samples. The results indicate that while variations in the modulus were statistically significant due to both layer height and size of the specimen in TPU, variations in PC were only statistically significant due to layer height. The highest elastic modulus was observed at a 0.2 mm layer height for both materials across different sizes. These findings offer valuable insights into design components for FFF, emphasizing the importance of considering mechanical property variations due to feature size, especially in TPU. Furthermore, locations with a higher probability of failure are recommended to be printed closer to the print bed, especially for TPU, because of the lower void volume fraction observed near the heated print bed. [ABSTRACT FROM AUTHOR]

As an important part of head protection equipment, research on the material and structural application of helmet liners has always been one of the hotspots in the field of helmets. This paper first discusses common helmet liner materials, including traditional polystyrene, polyethylene, polypropylene, etc., as well as newly emerging anisotropic materials, polymer nanocomposites, etc. Secondly, the design concept of the helmet liner structure is discussed, including the use of a multi-layer structure, the addition of geometric irregular bubbles to enhance the energy absorption effect, and the introduction of new manufacturing processes, such as additive manufacturing technology, to realize the preparation of complex structures. Then, the application of biomimetic structures to helmet liner design is analyzed, such as the design of helmet liner structures with more energy absorption properties based on biological tissue structures. On this basis, we propose extending the concept of bionic structural design to the fusion of plant stalks and animal skeletal structures, and combining additive manufacturing technology to significantly reduce energy loss during elastic yield energy absorption, thus developing a reusable helmet that provides a research direction for future helmet liner materials and structural applications. [ABSTRACT FROM AUTHOR]

This paper explores the new potential strategy of using fine recycled aggregates (fRA) derived from waste 3D printed concrete (3DPC) as a substitute for cement in additive manufacturing. This study hypothesizes that fRA can optimize mixture design, reduce cement content, and contribute to sustainable construction practices. Experimental programs were conducted to evaluate the fresh and hardened properties, printability window, and buildability of 3DPC mixes containing fRA. Mixes with replacement rates of cement with fRA by 10 vol%, 20 vol%, 30 vol%, 40 vol%, and 50 vol% were produced. A comprehensive experimental protocol consisting of rheological studies (static and dynamic yield stress), dynamic elastic modulus determination (first 24 h of hydration), flexural and compressive strengths (2 d and 28 d), and an open porosity test was performed. The obtained results were verified by printing tests. In addition, an economic and environmental life cycle assessment (LCA) of the mixes was performed. The results indicate that up to 50 vol% cement replacement with fRA is feasible, albeit with some technical drawbacks. While fRA incorporation enhances sustainability by reducing CO2 emissions and material costs, it adversely affects the printability window, green strength, setting time, and mechanical properties, particularly in the initial curing stages. Therefore, with higher replacement rates (above 20 vol%), potential optimization efforts are needed to mitigate drawbacks such as reduced green strength and buildability. Notably, replacement rates of up to 20 vol% can be successfully used without compromising the overall material properties or altering the mixture design. The LCA analysis shows that reducing the cement content and increasing the fRA addition results in a significant reduction in mix cost (up to 24%) and a substantial decrease in equivalent CO2 emissions (up to 48%). In conclusion, this study underscores the potential of fRA as a sustainable alternative to cement in 3D printed concrete. [ABSTRACT FROM AUTHOR]

Due to its lightweight, high strength, good machinability, and low cost, aluminum alloy has been widely used in fields such as aerospace, automotive, electronics, and construction. Traditional manufacturing processes for aluminum alloys often suffer from low material utilization, complex procedures, and long manufacturing cycles. Therefore, more and more scholars are turning their attention to the laser powder bed fusion (LPBF) process for aluminum alloys, which has the advantages of high material utilization, good formability for complex structures, and short manufacturing cycles. However, the widespread promotion and application of LPBF aluminum alloys still face challenges. The excellent printable ability, favorable mechanical performance, and low manufacturing cost are the main factors affecting the applicability of the LPBF process for aluminum alloys. This paper reviews the research status of traditional aluminum alloy processing and LPBF aluminum alloy and makes a comparison from various aspects such as microstructures, mechanical properties, application scenarios, and manufacturing costs. At present, the LPBF manufacturing cost for aluminum alloys is 2–120 times higher than that of traditional manufacturing methods, with the discrepancy depending on the complexity of the part. Therefore, it is necessary to promote the further development and application of aluminum alloy 3D printing technology from three aspects: the development of aluminum matrix composite materials reinforced with nanoceramic particles, the development of micro-alloyed aluminum alloy powders specially designed for LPBF, and the development of new technologies and equipment to reduce the manufacturing cost of LPBF aluminum alloy. [ABSTRACT FROM AUTHOR]

The rapid development of additive manufacturing (AM) has facilitated the creation of bionic lightweight, energy-absorbing structures, enabling the implementation of more sophisticated internal structural designs. For protective structures, the utilization of artificially controlled deformation patterns can effectively reduce uncertainties arising from random structural damage and enhance deformation stability. This paper proposed a bionic corrugated lightweight honeycomb structure with controllable deformation. The force on the onset state of deformation of the overall structure was investigated, and the possibility of controlled deformation in the homogeneous structure was compared with that in the corrugated structure. The corrugated structures exhibited a second load-bearing capacity wave peak, with the load-bearing capacity reaching 60.7% to 117.29% of the first load-bearing peak. The damage morphology of the corrugated structure still maintained relative integrity. In terms of energy absorption capacity, the corrugated lightweight structure has a much stronger energy absorption capacity than the homogeneous structure due to the second peak of the load carrying capacity. The findings of this study suggested that the combination of geometric customization and longitudinal corrugation through additive manufacturing offers a promising approach for the development of high-performance energy-absorbing structures. [ABSTRACT FROM AUTHOR]

Lattice structures have become an innovative solution for the improvement of part design, as they are able to substitute solid regions, maintain mechanical capabilities, and reduce material usage; however, dimensional quality control of these geometries is challenging. X-ray computed tomography (XCT) is the most suitable non-destructive metrological technique as it is capable of characterizing internal features and hidden elements. Uncertainty estimation of XCT is still in development, and studies typically use high-resolution calibrated devices such as focal variation microscopes (FVMs) as a reference, focusing on certain parts of the lattice but not the whole structure. In this paper, an estimation of the accuracy of XCT evaluation of a complete lattice structure in comparison to a higher-resolution reference device (FVM) is presented. Experimental measurements are taken on ad hoc designed test objects manufactured in polyamide 12 (PA12) using selective laser sintering (SLS), optimized for the evaluation on both instruments using different cubic-based lattice typologies. The results confirm higher precision on XCT evaluation in both qualitative and quantitative analysis. Even with a lower resolution, XCT is able to characterize details of the surface such as re-entrant features; as well, standard deviations and uncertainties in strut diameter evaluation remain more stable in all cells in XCT, identifying on the other hand reconstruction problems on FVM measurements. Moreover, it is shown that, using XCT, no additional evaluation errors were found in inner cells, suggesting that the measurement of external elements could be representative of the whole structure for metrological purposes. [ABSTRACT FROM AUTHOR]

This paper deals with the design of porous geometry of a heat transfer element. The proposed geometry combines a gyroid triply periodic minimal surface with the recursive principle of geometric body creation. The designed geometry is based on an attempt to increase the heat transfer surface while eliminating negative impacts on the fluid characteristics in the form of pressure loss or increase of the friction coefficient. The proposed geometry of the heat transfer element was compared with a pair of geometries based on the basic gyroid shape but with different channel size parameters. A numerical simulation was performed in Ansys Fluent 2020 R1 using the SST k-omega turbulence model for flow velocities in the range of 0.01 m.s−1 to 0.5 m.s−1, which covered a wide range of the Reynolds number and thus also flow forms in terms of the turbulence intensity. The presented results clearly show lower values of pressure loss and friction coefficient of the proposed geometry compared to the evaluated porous structures. Also, at the same time, they describe the factors positively influencing the mixing process of the liquid in the proposed element, which leads to an increase in the efficiency of the heat transfer process. [ABSTRACT FROM AUTHOR]

The aim of this paper was to evaluate the fracture resistance of 3D-printed zirconia occlusal veneers (OVs) of different thicknesses and supported by different abutment materials. Materials and Methods: The standard OV of a natural molar was prepared and digitized using a laboratory 3D scanner. The resulting digital tooth abutment was milled either using cobalt–chromium (CoCr) or a fiber-reinforced composite (FRC). All the abutments were digitized and standardized OVs (30° tilt of all the cusps) designed with 0.4 mm, 0.6 mm, or 0.8 mm wall thicknesses. The OVs were fabricated using either the Programill PM7 milling device (Ivoclar Vivadent, PM) or one of two 3D zirconia printers, Cerafab 7500 (Lithoz, LC) or Zipro-D (AON, ZD). The ZD samples were only tested on CoCr abutments. The completed OVs were luted to their abutments and subjected to artificial aging, consisting of thermocycling and chewing simulation before fracture testing with a steel sphere (d = 8 mm) as an antagonist with three contact points on the occlusal OV surface. Besides the total fracture resistance Fu,tot, the lowest contact force Fu,cont leading to the local fracture of a cusp was of interest. The possible effects of the factors fabrication approach, wall thickness, and abutment material were evaluated using ANOVA (α = 0.05; SPSS Ver.28). Results: The total fracture resistance/contact forces leading to failure ranged from Fu,tot = 416 ± 83 N/Fu,cont = 140 ± 22 N for the 0.4 mm OVs fabricated using LC placed on the FRC abutments to Fu,tot = 3309 ± 394 N (ZD)/Fu,cont = 1206 ± 184 N (PM) for the 0.8 mm thick OVs on the CoCr abutments. All the factors (the fabrication approach, abutment material, and OV wall thickness) had an independent effect on Fu,tot as well as Fu,cont (p < 0.032). In pairwise comparisons for Fu,tot of the OVs luted to the CoCr abutments, the ZD samples statistically outperformed the LC- and PM-fabricated teeth irrespective of the thickness (p < 0.001). Conclusions: Within the limitations of this study, the printed occlusal veneers exhibited comparable fracture resistances to those of the milled variants. However, more resilient abutments (FRC as a simulation of dentine) as well as a thinner wall thickness led to reduced OV fracture resistance, suggesting that 0.4 mm thick zirconia OVs should not be unreservedly used in every clinical situation. [ABSTRACT FROM AUTHOR]

This paper presents the results of research on the influence of the moisture content in a filament made of ABS polymer on the properties of products manufactured using FDM (fused deposition modeling). Tests were carried out on a standard printer, using the parameters recommended by the manufacturer and the literature on the subject. A special climatic chamber was used to condition the material. A negative impact of ABS filament moisture on the strength and dimensional accuracy of printed products and on the structure of their surface is demonstrated. When the range of the filament moisture is between 0.17% and 0.75%, the strength decreases by 25% and the sample thickness increases by 10%. It is also shown that this effect does not depend on the history of the polymer reaching a given moisture level, i.e., by absorbing moisture in the absorption process or releasing moisture in the desorption process. [ABSTRACT FROM AUTHOR]

The additive manufacturing (AM) of functional copper (Cu) parts is a major goal for many industries, from aerospace to automotive to electronics, because Cu has a high thermal and electrical conductivity as well as being ~10× cheaper than silver. Previous studies on AM of Cu have concentrated mainly on high-energy manufacturing processes such as Laser Powder Bed Fusion, Electron Beam Melting, and Binder Jetting. These processes all require high-temperature heat treatment in an oxygen-free environment. This paper shows an AM route to multi-layered microparts from novel nanoparticle (NP) Cu feedstocks, performed in an air environment, employing a low-power (<10 W) laser sintering process. Cu NP ink was deposited using two mechanisms, inkjet printing, and bar coating, followed by low-power laser exposure to induce particle consolidation. Initial parts were manufactured to a height of approximately 100 µm, which was achieved by multi-layer printing of 15 (bar-coated) to 300 (inkjetted) layers. There was no evidence of oxidised copper in the sintered material, but they were found to be low-density, porous structures. Nonetheless, electrical resistivity of ~28 × 10−8 Ω m was achieved. Overall, the aim of this study is to offer foundational knowledge for upscaling the process to additively manufacture Cu 3D parts of significant size via sequential nanometal ink deposition and low-power laser processing. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive approach aimed at developing a coupled process-structure simulation that integrates anisotropic and elastoplastic material behavior for plastic components manufactured through Fused Filament Fabrication (FFF) 3D printing. The simulation incorporates material orientation considerations, linking the process simulation with structural simulation. Subsequently, stress and strain values from the simulations are compared with the test results. Moreover, the fracture behavior of components manufactured in this way is also taken into account in relation to material orientation. The executed simulations have yielded successful outcomes, affirming the efficacy of the anisotropic and elastoplastic simulation across all strand orientations. Special attention is paid to the application of the method. Here, the simulation method introduced in this contribution with the approaches for describing the material behavior under mechanical load can be used in the future in the dimensioning of FFF manufactured plastic components to predict the deformation behavior and failure, especially under consideration of a well economic and efficient virtual product development. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) technology has recently seen increased utilization due to its versatility in using functional materials, offering a new pathway for next-generation conformal electronics in the smart sensor field. However, the limited availability of polymer-based ultraviolet (UV)-curable materials with enhanced piezoelectric properties necessitates the development of a tailorable process suitable for 3D printing. This paper investigates the structural, thermal, rheological, mechanical, and piezoelectric properties of a newly developed sensor resin material. The polymer resin is based on polyvinylidene fluoride (PVDF) as a matrix, mixed with constituents enabling UV curability, and boron nitride nanotubes (BNNTs) are added to form a nanocomposite resin. The results demonstrate the successful micro-scale printability of the developed polymer and nanocomposite resins using a liquid crystal display (LCD)-based 3D printer. Additionally, incorporating BNNTs into the polymer matrix enhanced the piezoelectric properties, with an increase in the voltage response by up to 50.13%. This work provides new insights for the development of 3D printable flexible sensor devices and energy harvesting systems. [ABSTRACT FROM AUTHOR]

Additive manufacturing has revolutionized manufacturing across a spectrum of industries by enabling the production of complex geometries with unparalleled customization and reduced waste. Beginning as a rapid prototyping tool, additive manufacturing has matured into a comprehensive manufacturing solution, embracing a wide range of materials, such as polymers, metals, ceramics, and composites. This paper delves into the workflow of additive manufacturing, encompassing design, modeling, slicing, printing, and post-processing. Various additive manufacturing technologies are explored, including material extrusion, VAT polymerization, material jetting, binder jetting, selective laser sintering, selective laser melting, direct metal laser sintering, electron beam melting, multi-jet fusion, direct energy deposition, carbon fiber reinforced, laminated object manufacturing, and more, discussing their principles, advantages, disadvantages, material compatibilities, applications, and developing trends. Additionally, the future of additive manufacturing is projected, highlighting potential advancements in 3D bioprinting, 3D food printing, large-scale 3D printing, 4D printing, and AI-based additive manufacturing. This comprehensive survey aims to underscore the transformative impact of additive manufacturing on global manufacturing, emphasizing ongoing challenges and the promising horizon of innovations that could further elevate its role in the manufacturing revolution. [ABSTRACT FROM AUTHOR]

Gyroid structures are among the most widely used three-dimensional elements produced by various additive manufacturing technologies. This paper focuses on a metrological analysis of Flexfill 92A material specimens with a relative density (25 to 85%) using industrial computer tomography. The results show that for a given structure, the best method is to use surface determination with the closure of internal defects in the material. The analysis implies that the smallest deviations of the specimens' external dimensions were achieved with respect to the CAD model at the highest relative densities. The wall thickness shows the smallest percentage change of 0.5685 at 45% relative density and the largest at 25% and 85% relative density. The nominal–actual comparison of manufactured specimens to the CAD model shows the smallest cumulative deviation of 0.209 mm at 90% and 25% relative density, while it slightly increases with increasing relative density. All produced specimens have a smaller material volume than their theoretical volume value, while the percentage change in volume is up to 8.6%. The surface of specimens is larger compared with the theoretical values and the percentage change reaches up to 25.3%. The percentage of pores in the specimens increases with increasing relative density and reaches 6%. The acquired knowledge will be applied in the framework of research focused on the possibilities of using additive manufacturing to produce a skeleton of rubber–textile conveyor belts. This paper presents initial research on the possibility of replacing the carcass of rubber–textile belts with an additive technology use. [ABSTRACT FROM AUTHOR]

Material jetting technology is gaining popularity, especially in polymer science, because of their high accuracy for additive manufacturing (AM) products. This paper aims to investigate the quality of micro-holes that are oriented in three basic directions, and manufactured by the material jetting AM process. This paper proposes a novel methodology to evaluate the accuracy of micro-holes features by using a transparent artifact. A test artifact with horizontal and vertical micro-holes in it, with industrial applications, was designed. Micro-holes were placed on planar and curve surfaces. Samples were manufactured by PolyJet technology from a translucent photopolymer resin which allows a facile investigation (by microscopy) of the inner structure of the micro-holes. The features of ten micro-holes printed in matte and glossy finish type, with diameters in coarse and medium options, according to ISO/ASTM 52902, were analyzed. Quality analysis of the micro-holes features was performed by microscopy investigations. The effects of main factors on the deviation of the micro-hole diameter were investigated by using the statistical design of experiments, and four control factors were considered. The best results were obtained for sample printed in matte finishing with the micro-holes oriented along the x-axis and z-axis. The smallest diameter of the micro-holes obtained by PolyJet technology on an EDEN 350 machine was 0.5 mm, but in industrial applications for a facile post-processing, a higher diameter is recommended to be used. A confirmatory experiment on a wing sample, with a number of micro-holes of the same diameter and a large length to diameter ratio of the micro-holes, was performed, and the repeatability of the results was confirmed. [ABSTRACT FROM AUTHOR]

The continuous growth of additive manufacturing in worldwide industrial and research fields is driven by its main feature which allows the customization of items according to the customers' requirements and limitations. There is an expanding competitiveness in the product development sector as well as applicative research that serves special-use domains. Besides the direct use of additive manufacturing in the production of final products, 3D printing is a viable solution that can help manufacturers and researchers produce their support tooling devices (such as molds and dies) more efficiently, in terms of design complexity and flexibility, timeframe, costs, and material consumption reduction as well as functionality and quality enhancements. The compatibility of the features of 3D printing of molds with the requirements of low-volume production and individual-use customized items development makes this class of techniques extremely attractive to a multitude of areas. This review paper presents a synthesis of the use of 3D-printed polymeric molds in the main applications where molds exhibit a major role, from industrially oriented ones (injection, casting, thermoforming, vacuum forming, composite fabrication) to research or single-use oriented ones (tissue engineering, biomedicine, soft lithography), with an emphasis on the benefits of using 3D-printed polymeric molds, compared to traditional tooling. [ABSTRACT FROM AUTHOR]

In the realm of cementitious materials, integrating nanoclay shows promise in enhancing properties relevant to additive manufacturing. This paper presents a novel mathematical model that combines simple empirical dissolution/nucleation Avrami-like kinetics with a thixotropic kinetics equation. To analyze the initial exothermic peak, two sets of the calculation parameter function are built to describe the exothermic rate as a function of time, following an exponential pattern. This allows for the prediction of the changes in cumulative heat and heat rate during hydration, considering different concentrations of nanoclay. In the rheological aspect, the relationship between shear stress, shear rate, and time is modeled as a combination of exponential dependencies. This enables the prediction of the variations in shear stress with one variable while holding the other constant (either time or shear rate). By integrating these aspects, this model effectively describes both the first exothermal peak and the rheological behavior during cement hydration with the inclusion of nanoclay. Validated against experimental results, these models demonstrate good accuracy (overall below 3% error), reliability, and applicability. The findings offer valuable insights into the thermal and rheological aspects of concrete printing, enabling informed design decisions for both scientific and industrial applications. [ABSTRACT FROM AUTHOR]

The objective of this study was to review the scientific evidence currently available on 3D printable materials and 3D printing technologies used for the fabrication of permanent restorations, focusing on material properties that are clinically relevant. A literature search was performed on four databases (MEDLINE/PubMed, Scopus, Cochrane Library, Web of Science) for articles published from January 2013 until November 2023, using a combination of free words: (restorative dentistry OR prosthetic dentistry) AND (3D printing OR additive manufacturing OR rapid prototyping) AND materials. Two reviewers screened titles and/or abstracts of 2.468 unique studies. In total, 83 studies were selected for full-text reading, from which 36 were included in the review. The assessed variables were mechanical properties, reporting in most of the cases positive results, dimensional accuracy and fit, reporting conflicting results with a predominance of positive, aesthetic properties, with positive reports but scarcely addressed, and biological properties, almost unexplored in independent studies. Despite numerous studies with positive results in favor, papers with negative outcomes were also retrieved. Aesthetic and biological properties are conversely still mostly unexplored. There remains a lack of conclusive evidence for viable 3D printable restorative and prosthodontic materials for permanent restorations. Research should be strengthened by defining international standards for laboratory testing and, where pre-clinical data are promising, conducting clinical trials. [ABSTRACT FROM AUTHOR]

Recent progress in additive manufacturing, also known as 3D printing, has offered several benefits, including high geometrical freedom and the ability to create bioinspired structures with intricate details. Mantis shrimp can scrape the shells of prey molluscs with its hammer-shaped stick, while beetles have highly adapted forewings that are lightweight, tough, and strong. This paper introduces a design approach for bioinspired lattice structures by mimicking the internal microstructures of a beetle's forewing, a mantis shrimp's shell, and a mantis shrimp's dactyl club, with improved mechanical properties. Finite element analysis (FEA) and experimental characterisation of 3D printed polylactic acid (PLA) samples with bioinspired structures were performed to determine their compression and impact properties. The results showed that designing a bioinspired lattice with unit cells parallel to the load direction improved quasi-static compressive performance, among other lattice structures. The gyroid honeycomb lattice design of the insect forewings and mantis shrimp dactyl clubs outperformed the gyroid honeycomb design of the mantis shrimp shell, with improvements in ultimate mechanical strength, Young's modulus, and drop weight impact. On the other hand, hybrid designs created by merging two different designs reduced bending deformation to control collapse during drop weight impact. This work holds promise for the development of bioinspired lattices employing designs with improved properties, which can have potential implications for lightweight high-performance applications. [ABSTRACT FROM AUTHOR]

In this paper, the influences of two post-heat treatments on the structural, mechanical and corrosion resistance properties of additively manufactured Ti6Al4V alloys were discussed in detail. The materials were produced using the laser engineering net shaping (LENS) technique, and they were subjected to annealing without pressure and hot isostatic pressing (HIP) under a pressure of 300 MPa for 30 min at temperatures of 950 °C and 1050 °C. Annealing without pressure led to the formation of a thin plate structure, which was accompanied by decreasing mechanical properties and increasing elongation and corrosion resistance values. For the HIP process, the formation of a thick plate structure could be observed, resulting in the material exhibiting optimal mechanical properties and unusually high elongation. The best mechanical and corrosion resistance properties were obtained for the material subjected to HIP at 950 °C. [ABSTRACT FROM AUTHOR]

This study focuses on evaluating the fatigue life performance of 3D-printed polymer composites produced through the fused deposition modelling (FDM) technique. Fatigue life assessment is essential in designing components for industries like aerospace, medical, and automotive, as it provides an estimate of the component's safe service life during operation. While there is a lack of detailed research on the fatigue behaviour of 3D-printed polymer composites, this paper aims to fill that gap. Fatigue tests were conducted on the 3D-printed polymer composites under various loading conditions, and static (tensile) tests were performed to determine their ultimate tensile strength. The fatigue testing load ranged from 80% to 98% of the total static load. The results showed that the fatigue life of the pressed samples using a platen press was significantly better than that of the non-pressed samples. Samples subjected to fatigue testing at 80% of the ultimate tensile strength (UTS) did not experience failure even after 1 million cycles, while samples tested at 90% of UTS failed after 50,000 cycles, with the failure being characterized as splitting and clamp area failure. This study also included a lap shear analysis of the 3D-printed samples, comparing those that were bonded using a two-part Araldite glue to those that were fabricated as a single piece using the Markforged Mark Two 3D printer. In summary, this study sheds light on the fatigue life performance of 3D-printed polymer composites fabricated using the FDM technique. The results suggest that the use of post-printing platen press improved the fatigue life of 3D-printed samples, and that single printed samples have better strength of about 265 MPa than adhesively bonded samples in which the strength was 56 MPa. [ABSTRACT FROM AUTHOR]

This literature review indicates that the basic microstructure of Ti6Al4V is bimodal, consisting of two phases, namely α + β, and it occurs after fabrication using conventional methods such as casting, plastic forming or machining processes. The fabrication of components via an additive manufacturing process significantly changes the microstructure and properties of Ti6Al4V. Due to the rapid heat exchange during heat treatment, the bimodal microstructure transforms into a lamellar microstructure, which consists of two phases: α′ + β. Despite the application of optimum printing parameters, 3D printed products exhibit typical surface defects and discontinuities, and in turn, surface finishing using shot peening is recommended. A literature review signalizes that shot peening and electropolishing processes positively impact the corrosion behavior, the mechanical properties and the condition of the surface layer of conventionally manufactured titanium alloy. On the other hand, there is a lack of studies combining shot peening and electropolishing in one hybrid process for additively manufactured titanium alloys, which could synthesize the benefits of both processes. Therefore, this review paper clarifies the effects of shot peening and electropolishing treatment on the properties of both additively and conventionally manufactured Ti6Al4V alloys and shows the effect process on the microstructure and properties of Ti6Al4V titanium alloy. [ABSTRACT FROM AUTHOR]

The present study focuses on an up-to-date topic regarding flying equipment identified within the category of drones that use, for propulsion and air movements, the power generated by electric motors. In this paper, researchers focus on implementing bladeless technology to calculate, develop, and construct flying equipment known in the literature as drones. The entire structure of the prototype, all the needed parts, is to be obtained using additive manufacturing technologies, which assumes practical realization using 3D-printing equipment. Nowadays, the 3D-printing process has been proven to be a reliable solution when it comes to manufacturing complex shape parts in quite a short time and with reduced costs. The practical study within the present research aims to obtain polymer-based, lightweight parts with complex shapes inside to be implemented in the propulsion of a drone. The complex surface geometry of the parts that this research used is influenced by the ventilation technology offered by the "Air Multiplier" technology. The entire structure of the final drone equipment, all the parts, is to be manufactured using fused filament fabrication (FFF). The main purpose of the fusion is to use the advantages offered by this technology in drones to obtain advantages such as augmented values of thrust, a more agreeable and muffled sound signature, or an increased level of safety. [ABSTRACT FROM AUTHOR]

Metal binder jetting shows great potential for medical technology. This potential can be exploited by integrating binder jetting into existing process routes known from metal injection molding. The biggest challenge here is the flowability and packing behavior of the powders used, due to their low size distributions. This paper investigates different powder-drying strategies to improve flowability using a statistical experimental design. Because of its relevance for medical applications, spherical Ti-6Al-4V powder with a size distribution under 25 µm is dried under various parameters using vacuum and gas purging. The investigated parameters, time and temperature, are selected in a central-composite-circumscribed test plan with eleven tests and three center points. The target parameters—water content, flowability and impurity levels (oxygen, nitrogen)—of the powder are analyzed. For validation, practical test trials are carried out on an industrial binder jetting system with unconditioned powder and conditioning with optimized parameters, comparing the manufactured parts and the powder bed. An optimized drying cycle with a duration of 6 h at 200 °C was determined for the investigated powder. Significant improvements in the dimensional accuracy (from ±1.5 to 0.3%) of the components and the visual impression of the powder bed are demonstrated. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM), commonly referred to as 3D printing, has revolutionized the manufacturing landscape by enabling the intricate layer-by-layer construction of three-dimensional objects. In contrast to traditional methods relying on molds and tools, AM provides the flexibility to fabricate diverse components directly from digital models without the need for physical alterations to machinery. Four-dimensional printing is a revolutionary extension of 3D printing that introduces the dimension of time, enabling dynamic transformations in printed structures over predetermined periods. This comprehensive review focuses on polymeric materials in 3D printing, exploring their versatile processing capabilities, environmental adaptability, and applications across thermoplastics, thermosetting materials, elastomers, polymer composites, shape memory polymers (SMPs), including liquid crystal elastomer (LCE), and self-healing polymers for 4D printing. This review also examines recent advancements in microvascular and encapsulation self-healing mechanisms, explores the potential of supramolecular polymers, and highlights the latest progress in hybrid printing using polymer–metal and polymer–ceramic composites. Finally, this paper offers insights into potential challenges faced in the additive manufacturing of polymer composites and suggests avenues for future research in this dynamic and rapidly evolving field. [ABSTRACT FROM AUTHOR]

The properties of 3D-printed bodies are an essential part of both the industrial and research sectors, as the manufacturers try to improve them in order to make this now additive manufacturing method more appealing compared to conventional manufacturing methods, like injection moulding. Great achievements were accomplished in both 3D printing materials and machines that made 3D printing a viable way to produce parts in recent years. However, in terms of printing parameters, there is still much room for advancements. This paper discusses four of the 3D printing parameters that affect the properties of the final products made by chopped glass fibre-filled nylon filaments; these parameters are the printing temperature, nozzle diameter, layer height, and infill orientation. Furthermore, a polynomial function was fitted to the measured data points, which made it possible to calculate the tensile strength, flexural strength, and Young's modulus of the 3D-printed samples based on their printing parameters. A Pearson correlation analysis was also carried out to determine the impact of each parameter on all three mechanical properties studied. Both the infill orientation and printing temperature had a significant effect on both strengths and Young's modulus, while the effect of nozzle diameters and layer heights were dependent on the infill orientation used. Also, a model with excellent performance was established to predict the three mechanical properties of the samples based on the four major parameters used. As expected from a fibre-reinforced material, the infill orientation had the most significant effect on the tensile strength, flexural strength, and Young's modulus. The temperature was also quite significant, while the nozzle diameters and layer height effect were situational. The highest values for the tensile strength, flexural strength, and Young's modulus were 72 MPa, 78.63 MPa, and 4243 MPa, respectively, which are around the same values the manufacturer states. [ABSTRACT FROM AUTHOR]

This paper aims to compare two ceramic materials available for additive manufacturing (AM) processes—vat photopolymerization (VPP) and material extrusion (MEX)—that result in fully ceramic parts after proper heat treatment. The analysis points out the most significant differences between the structural and mechanical properties and the potential application of each AM technology. The research revealed different behaviors for the specimens obtained via the two mentioned technologies. In the case of MEX, the specimens exhibited similar microstructures before and after heat treatment. The sintering process did not affect the shape of the grains, only their size. For the VPP specimens, directly after the manufacturing process, irregular grain shapes were registered, but after the sintering process, the grains fused, forming a solid structure that made it impossible to outline individual grains and measure their size. The highest compression strength was 168 MPa for the MEX specimens and 81 MPa for the VPP specimens. While the VPP specimens had half the compression strength, the results for the VPP specimens were significantly more repeatable. [ABSTRACT FROM AUTHOR]

This paper deals with the numerical modelling of non-destructive testing of composite parts using active thermography. This method has emerged as a new approach for performing non-destructive testing (NDT) on continuous carbon fibre reinforced thermoplastic polymer (CCFRTP) components, particularly in view of detecting porosity or delamination. In this context, our numerical model has been developed around references containing internal defects of various shapes and sizes. The first novelty lies in the fact that the heat source used in the experimental setup is modelled exhaustively to accurately model the radiation emitted by the lamp, as well as the convection and conduction around the bulb. A second novelty concerns the modelling of the CCFRTP making up the benchmark used. Indeed, its thermal properties vary as a function of the sample temperature. Therefore, the actual thermal properties have been experimentally measured and were later used in our model. The latter then captures the material dependency on temperature. The results obtained by our model proved to be in close agreement with the experimental results on real reference points, paving the way for future use of the model to optimise experimental configurations and, in particular, the heating parameters. [ABSTRACT FROM AUTHOR]

In the field of three-dimensional object design and fabrication, this paper explores the transformative potential at the intersection of biomaterials, biopolymers, and additive manufacturing. Drawing inspiration from the intricate designs found in the natural world, this study contributes to the evolving landscape of manufacturing and design paradigms. Biomimicry, rooted in emulating nature's sophisticated solutions, serves as the foundational framework for developing materials endowed with remarkable characteristics, including adaptability, responsiveness, and self-transformation. These advanced engineered biomimetic materials, featuring attributes such as shape memory and self-healing properties, undergo rigorous synthesis and characterization procedures, with the overarching goal of seamless integration into the field of additive manufacturing. The resulting synergy between advanced manufacturing techniques and nature-inspired materials promises to revolutionize the production of objects capable of dynamic responses to environmental stimuli. Extending beyond the confines of laboratory experimentation, these self-transforming objects hold significant potential across diverse industries, showcasing innovative applications with profound implications for object design and fabrication. Through the reduction of waste generation, minimization of energy consumption, and the reduction of environmental footprint, the integration of biomaterials, biopolymers, and additive manufacturing signifies a pivotal step towards fostering ecologically conscious design and manufacturing practices. Within this context, inanimate three-dimensional objects will possess the ability to transcend their static nature and emerge as dynamic entities capable of evolution, self-repair, and adaptive responses in harmony with their surroundings. The confluence of biomimicry and additive manufacturing techniques establishes a seminal precedent for a profound reconfiguration of contemporary approaches to design, manufacturing, and ecological stewardship, thereby decisively shaping a more resilient and innovative global milieu. [ABSTRACT FROM AUTHOR]

Titanium alloys face challenges of high temperature oxidation during the service period when used as aircraft engine components. In this paper, the effect of Y2O3 addition on the oxidation behavior and the microstructural change of the Ti6Al4V alloy fabricated by selective laser melting (SLM) was comprehensively studied. The results show that the surface of the Ti6Al4V alloy is a dense oxide layer composed of TiO2 and Al2O3 compounds. The thickness of the oxide layer of the Ti6Al4V increased from 59.55 μm to 139.15 μm. In contrast, with the addition of Y2O3, the thickness of the oxide layer increased from 35.73 μm to 80.34 μm. This indicates that the thickness of the oxide layer formation was a diffusion-controlled process and, therefore, the thickness of the oxide layer increased with an increase in temperature. The Ti6Al4V-1.0 wt.% Y2O3 alloy exhibits excellent oxidation resistance, and the thickness is significantly lower than that of the Ti6Al4V alloy. The oxidation kinetics of the Ti6Al4V and Ti6Al4V-1.0 wt.% Y2O3 alloys at 600 °C and 800 °C follows a parabolic rule, whereas the oxidation of the Ti6Al4V and Ti6Al4V-1.0 wt.% Y2O3 alloys at 1000 °C follows the linear law. The average microhardness values of Ti6Al4V samples after oxidation increased to 818.9 ± 20 HV0.5 with increasing temperature, and the average microhardness values of the Ti6Al4V-1.0 wt.% Y2O3 alloy increases until 800 °C and then decreases at 1000 °C. The addition of Y2O3 shows a significant improvement in the microhardness during the different temperatures after oxidation. [ABSTRACT FROM AUTHOR]