Search

Herein, a new, direct paper-based fluorimetric method is described for the quantitative determination of glutathione (GSH) molecules in nutritional supplements. Briefly, the proposed analytical method is based on the fluorescence emission resulting from the direct and selective chemical reaction of GSH molecules with the derivatization reagent that is o-phthalaldehyde (OPA) in acidic conditions at room temperature. The intensity of the emitted fluorescence on the surface of the analytical paper devices after irradiation with a lamp at 365 nm is proportional to the concentration of GSH and is measured using a smartphone as the detector. This methodology, which is suitable for measurements in laboratories with limited resources, does not require specialized instrumentation or trained personnel. The protocol governing the proposed method is simple and easily applicable. Essentially, the chemical analyst should adjust the value of pH on the surface of the paper by adding a minimal amount of buffer solution; then, after adding a few microliters of the derivatization reagent, wait for the surface of the paper to dry and, finally, add the analyte. Subsequently, the irradiation of the sensor and the measurement of the emitted fluorescence can be recorded with a mobile phone. In the present study, several parameters affecting the chemical reaction and the emitted fluorescence were optimized, the effect of interfering compounds that may be present in dietary supplements was examined, and the stability of these paper sensors under different storage conditions was evaluated. Additionally, the chemical stability of these paper devices in various maintenance conditions was studied, with satisfactory results. The detection limit calculated as 3.3 S/N was 20.5 μmol L -1 , while the precision of the method was satisfactory, ranging from 3.1% (intra-day) to 7.3% (inter-day). Finally, the method was successfully applied to three different samples of dietary supplements.

Flexible paper-based materials play a crucial role in the field of flexible electromagnetic shielding due to their thinness and controllable shape. In this study, we employed the wet paper forming technique to prepare carbon fiber paper with a thickness gradient. The electromagnetic shielding performance of the carbon fiber paper varies with the ladder-like thickness distribution. Specifically, an increase in thickness gradient leads to higher reflectance of the carbon fiber paper. Within the X-band frequency range (8.2–12.4 GHz), reflectivity decreases as electromagnetic wave frequency increases, indicating enhanced penetration of electromagnetic waves into the interior of the carbon fiber paper. This enhancement is attributed to an increased fiber content per unit area resulting from a greater thickness gradient, which further enhances reflection loss and promotes internal multiple reflections and scattering effects, leading to increased absorption loss. Notably, at a 5 mm thickness, our carbon fiber paper exhibits an impressive average overall shielding performance, reaching 63.46 dB. Moreover, it exhibits notable air permeability and mechanical properties, thereby assuming a pivotal role in the realm of flexible wearable devices in the foreseeable future. [ABSTRACT FROM AUTHOR]

Polyethylene-, polyvinylidene chloride-, and per- and polyfluoroalkyl substance-coated paper generate microplastics or fluorochemicals in the environment. Here, we report an approach for the development of oil-resistant papers using an environmentally friendly, fluorine-free, water-dispersible poly(dimethylsiloxane) (PDMS) coating on kraft paper. Carboxylic-functionalized PDMS (PDMS-COOH) was synthesized and subsequently neutralized with ammonium bicarbonate to obtain a waterborne emulsion, which was then coated onto kraft paper. The water resistance of the coated paper was determined via Cobb60 measurements. The Cobb60 value was reduced to 2.70 ± 0.14 g/m2 as compared to 87.6 ± 5.1 g/m2 for uncoated paper, suggesting a remarkable improvement in water resistance. Similarly, oil resistance was found to be 12/12 on the kit test scale versus 0/12 for uncoated paper. In addition, the coated paper retained 70–90% of its inherent mechanical properties, and more importantly, the coated paper was recycled via pulp recovery using a standard protocol with a 91.1% yield. [ABSTRACT FROM AUTHOR]

As air pollution escalates, the need for air filters increases. It is better that the filters used be based on natural fibers, such as non-wood fibers, which cause low damage to the environment. However, the short fiber lengths, low apparent densities, and high volumes of non-wood materials can make it challenging to prepare filter paper with the required mechanical and physical properties. In that context, this study focused on utilizing bamboo fibers to fabricate filter paper by employing the anthraquinone soda pulping method. The pulp underwent bleaching and oxidation processes, with the incorporation of cationic starch (CS) and polyvinyl alcohol (PVA) to enhance resistance properties, resulting in the creation of handmade filter papers. The findings revealed that the tear, burst, and tensile strength of filter paper increased with the oxidation and addition of CS and PVA. Air permeability increased with addition of PVA and combination of CS and PVA. FTIR demonstrated the conversion of hydroxyl groups in cellulose chains to carboxyl groups due to oxidation. SEM images illustrated alterations in the fiber structure post-oxidation treatment, with CS reducing pores while PVA and the CS-PVA combination enlarged pore size and enhanced porosity. The BET surface area surface area expanded with oxidation and the addition of the CS-PVA blend, indicating heightened filter paper porosity. Notably, the combined inclusion of CS and PVA not only augmented mechanical strength but also increased porosity while maintaining pore size. [ABSTRACT FROM AUTHOR]

This study examined the possibility of using various types of waste paper—used newsprint (NP), used lightweight coated paper (LWC), used office paper (OP), and used corrugated cardboard (CC)—for the removal of anionic dyes, Acid Red 18 (AR18) and Acid Yellow 23 (AY23), and cationic dyes, Basic Violet 10 (BV10) and Basic Red 46 (BR46), from aqueous solutions. The scope of this research included the characterization of sorbents (FTIR, SEM, BET surface area, porosity, pHPZC, effectiveness of water coloration), determination of pH effect on the effectiveness of dye sorption, sorption kinetics (pseudo-first-order model, second-order model, intraparticular diffusion model), and the maximum sorption capacity (Langmuir models and Freundlich model) of the tested sorbents. The use of waste paper materials as sorbents was found to not pose any severe risk of aquatic environment contamination. AR18, AY23, and BV10 sorption intensities were the highest at pH 2, and that of RB46 at pH 6. The waste paper sorbents proved particularly effective in removing cationic dyes, like in the case of, e.g., NP, which had a sorption capacity that reached 38.87 mg/g and 90.82 mg/g towards BV10 and BR46, respectively, and were comparable with that of selected activated carbons (literature data). [ABSTRACT FROM AUTHOR]

The lifespan of an electrical transformer, primarily determined by the condition of its solid insulation, is well known under various operating conditions when mineral oil is the coolant in these machines. However, there is a trend toward replacing this oil with biodegradable fluids, especially esters; therefore, an understanding of the ageing of solid insulation with these fluids is essential. Currently available data do not allow for the selection of the best ester among those available on the market, as each study applies different conditions, making it impossible to compare results. Thus, this paper analyses the degradation of Kraft and Thermally Upgraded Kraft papers with the following five most promising commercial esters: sunflower, rapeseed, soybean, palm, and synthetic. The materials underwent accelerated thermal ageing at 130, 150, and 170 °C, and the integrity of the papers was evaluated through their polymerisation degree and the obtaining of the degradation kinetic models. The wide range of materials studied in this work, which were subjected to the same treatments, allows for a comparison of the esters, revealing significant differences in the impact of the alternative fluids. Sunflower, rapeseed, and soybean esters provided the best paper protection, i.e., the degree of polymerisation of Kraft paper in the tests at 150 °C decreased by 71% with these fluids, compared to the 83% reduction with mineral oil, 79% reduction with palm ester, and 75% reduction with synthetic ester. Furthermore, different kinetic models were obtained to predict the degradation; it was concluded that the Emsley model provides the best fit. Additionally, it was found that the behaviour of a dielectric fluid with one type of paper cannot be extrapolated, which is only noticeable in broad-scope studies. [ABSTRACT FROM AUTHOR]

In the realm of electrochemical nitrite detection, the potent oxidizing nature of nitrite typically necessitates operation at high detection potentials. However, this study introduces a novel approach to address this challenge by developing a highly sensitive electrochemical sensor with a low reduction detection potential. Specifically, a copper metal nanosheet/carbon paper sensitive electrode (Cu/CP) was fabricated using a one-step electrodeposition method, leveraging the catalytic reduction properties of copper's high occupancy d-orbital. The Cu/CP sensor exhibited remarkable performance in nitrite detection, featuring a low detection potential of −0.05 V vs. Hg/HgO, a wide linear range of 10~1000 μM, an impressive detection limit of 0.079 μM (S/N = 3), and a high sensitivity of 2140 μA mM−1cm−2. These findings underscore the efficacy of electrochemical nitrite detection through catalytic reduction as a means to reduce the operational voltage of the sensor. By showcasing the successful implementation of this strategy, this work sets a valuable precedent for the advancement of electrochemical low-potential nitrite detection methodologies. [ABSTRACT FROM AUTHOR]

Many plant materials in nature have the ability to change their shape to respond to external stimuli, such as humidity or moisture, to ensure their survival or safe seed release. A well-known example for this phenomenon is the pinecone, which is able to open its scales at low humidity due to the specific bilayer structures of the scale. Inspired by this, we developed a novel humidity-driven actuator based on paper. This was realized by the lamination of untreated paper made from eucalyptus fibers to a paper–carboxymethyl cellulose (CMC) composite. As observed, the hygroexpansion of the composite can be easily controlled by the amount of CMC in the impregnated paper sheet, which, thus, controls the morphologic deformation of the paper bilayer. For a more detailed understanding of these novel paper soft robots, we also studied the dynamic water vapor adsorption, polymer distribution and hygroexpansion of the paper–polymer composites. Finally, we applied a geometrically nonlinear finite element model to predict the bending behavior of paper bilayers and compared the results to experimental data. From this, we conclude that due to the complexity of structure of the paper composite, a universal prediction of the hygromorphic behavior is not a trivial matter. [ABSTRACT FROM AUTHOR]

Paper documents are an important carrier of information related to human civilization, with the reinforcement and protection of fragile paper documents being a key aspect of their protection. This research utilized amphoteric polyvinylamine polymer as a paper reinforcement agent, strengthening the Xuan paper commonly used in paper documents. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS), solid-state 13C NMR, and other analytical methods were employed to compare the physical properties, micro-morphology, crystallinity, and aging resistance of the paper before and after reinforcement. Research was conducted on the effects of reinforcement, the aging resistance, and the effects on the fiber structure. The results indicate that polyethylenimine has a filling and bridging effect between the paper fibers. After treatment with polyethylenimine, there was a significant improvement in the folding endurance and tensile strength of the paper. Additionally, the paper maintains a good mechanical strength even after undergoing dry heat and humid aging. [ABSTRACT FROM AUTHOR]

Sulfite, a widely used food additive, is subject to regulated labeling. The extraction of sulfite as the stable hydroxymethylsulfonate (HMS) form and its quantitative analysis by liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been recognized for their good sensitivity, selectivity, and versatility across various food materials. This study aimed to develop a cost-effective and simpler method for sulfite quantitation, while maintaining the superior sensitivity and selectivity of mass spectrometry (MS). To achieve this, we introduced paper spray ionization (PSI), an ambient desorption ionization technique that could achieve the direct measurement of analytes without employing separation. We also employed a novel internal standard (IS) structurally similar to the analyte, replacing the more expensive isotopically labeled IS. Although the PSI-MS/MS method developed in this study exhibited slightly lower analytical performance compared to the conventional LC-MS/MS, it remained effective for sulfite analysis in dried fruits.

In this paper, the aging characterization of a kind of insulating paper modified by magnetron sputtering MgO particles based on a microstrip resonant sensor was presented. Firstly, the modified insulating paper with 0, 15 and 30 min MgO particle sputtering times was prepared by a magnetron sputtering device. After that, the properties of the modified insulating paper with different sputtering times were analyzed through microscopic characterization, infrared spectrum, polymerization degree, dielectric constant, AC breakdown strength and thermal aging experiments. The results show that the dielectric constant of the modified insulating paper decreased obviously, the AC breakdown strength increased and the thermal aging resistance was better after 15 min of sputtering. The overall performance of the modified insulating paper after 30 min of sputtering is reduced due to excessive sputtering. In addition, microstrip resonant sensors are introduced to characterize the thermal aging degree of the modified insulating paper, and two microstrip resonant sensors are prepared: a complementary split ring resonator (CSRR) and an interdigital-capacitor-shaped defected ground structure resonator (IDCS-DGS). The resonance frequency deviation of the modified insulating paper samples after aging was measured by microstrip resonance sensors to show the influence of aging temperature on aging degree. The experimental results show that the test results of the microstrip resonance sensors are in good agreement with the traditional characterization methods and can characterize the various aging stages of the modified insulating paper to a certain extent, which proves the feasibility of the characterization method. [ABSTRACT FROM AUTHOR]

Specialized cancer treatments have the potential to exploit glutamine dependence to increase patient survival rates. Glutamine diagnostics capable of tracking a patient's response to treatment would enable a personalized treatment dosage to optimize the tradeoff between treatment success and dangerous side effects. Current clinical glutamine testing requires sophisticated and expensive lab-based tests, which are not broadly available on a frequent, individualized basis. To address the need for a low-cost, portable glutamine diagnostic, this work engineers a cell-free glutamine biosensor to overcome assay background and signal-to-noise limitations evident in previously reported studies. The findings from this work culminate in the development of a shelf-stable, paper-based, colorimetric glutamine test with a high signal strength and a high signal-to-background ratio for dramatically improved signal resolution. While the engineered glutamine test is important progress towards improving the management of cancer and other health conditions, this work also expands the assay development field of the promising cell-free biosensing platform, which can facilitate the low-cost detection of a broad variety of target molecules with high clinical value.

In the field of book heritage, it is important to develop cleaning/disinfecting treatments that can slow down the degradation of paper to prevent evident and irreversible damage. The objectives of the cleaning treatments are to remove external contaminants and oxidation and decomposition products of the paper, but these processes must not modify the unique characteristics of the book heritage resulting in irreversible changes in the structure of the paper. Recently, several innovative cleaning treatments were developed with the aim of being minimally invasive; however, to assess the effect of these treatments on paper, it is necessary to use a diagnostic non-destructive, rapid, and affordable process. In previous work, we used surface scanning Raman spectroscopy to develop a diagnostic protocol able to follow the aging processes of the paper, discriminating between hydrolysis and oxidation. In this paper, we applied this protocol to study the action of different types of treatments (hydrogel and EUV irradiation), evaluating both their effectiveness and impact on paper parameters. The results reported here demonstrate that the developed in operando diagnostic procedure can follow the changes in the paper structure comparing them to the variability due to the intrinsic inhomogeneity of paper, without sample contact in a rapid and effective way. [ABSTRACT FROM AUTHOR]

New biodegradable paper-based films are a hot research topic in the development of green agriculture. In this study, a black paper-based film coated with cooked tung oil with excellent mechanical properties, a hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high-pigment carbon black solution on the surface of base paper. The results showed that the surface-solidified oil film had a rough structure produced via the brush coating process using cooked tung oil. The base film of the black paper had a given hydrophobic structure, and the contact angle reached 98.9°. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black gives the black paper base film a heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of a cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil. [ABSTRACT FROM AUTHOR]

This manuscript offers a concise overview of paper microfluidics, emphasizing its sustainable sensing applications in healthcare, environmental monitoring, and food safety. Researchers have developed innovative sensing platforms for detecting pathogens, pollutants, and contaminants by leveraging the paper's unique properties, such as biodegradability and affordability. These portable, low-cost sensors facilitate rapid diagnostics and on-site analysis, making them invaluable tools for resource-limited settings. This review discusses the fabrication techniques, principles, and applications of paper microfluidics, showcasing its potential to address pressing challenges and enhance human health and environmental sustainability. [ABSTRACT FROM AUTHOR]

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we employed radio frequency (RF) sputtering of zinc oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 min, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400 °C for 10 min, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70-fold and a photocurrent increase of 13.86-fold, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors. [ABSTRACT FROM AUTHOR]

This review explores circular economy principles in regard to ethanol production from paper-mill sludge. Environmental sustainability and renewability over fossil fuels make second generation ethanol an attractive energy source in a rapidly growing population and consumption world. Paper sludge (PS), a by-product of the pulp and paper (P&P) industry, can no longer be recycled for paper production and is mainly disposed of in landfills. Therefore, it poses a major environmental challenge. However, it has shown potential as a valuable raw material for ethanol production, along with other pulp and paper products, due to its abundant availability and high cellulosic content. This waste-to-energy (WtE) technology for ethanol production is proposed as an alternative, aligning with circular economy concepts to maximize resource efficiency and minimize waste. This review underlines the circular economy aspects of bioethanol production within paper mill sludge management systems. Circular economy principles applied to ethanol production from PS offer a promising avenue for sustainable biofuel development that not only addresses waste management challenges but also enhances the overall environmental performance of biofuel production. Furthermore, economic benefits are described, highlighting the potential for job creation and community development. [ABSTRACT FROM AUTHOR]

Excessive emissions of heavy metals not only cause environmental pollution but also pose a direct threat to human health. Therefore, rapid and accurate detection of heavy metals in the environment is of great significance. Herein, we propose a method based on laser-induced breakdown spectroscopy (LIBS) combined with filter paper modified with bovine serum albumin-protected gold nanoclusters (LIBS-FP-AuNCs) for the rapid and sensitive detection of Cr3+ and Mn2+. The filter paper modified with AuNCs was used to selectively enrich Cr3+ and Mn2+. Combined with the multi-element detection capability of LIBS, this method achieved the simultaneous rapid detection of Cr3+ and Mn2+. Both elements showed linear ranges for concentrations of 10–1000 μg L−1, with limits of detection of 7.5 and 9.0 μg L−1 for Cr3+ and Mn2+, respectively. This method was successfully applied to the determination of Cr3+ and Mn2+ in real water samples, with satisfactory recoveries ranging from 94.6% to 105.1%. This method has potential application in the analysis of heavy metal pollution. [ABSTRACT FROM AUTHOR]

Oil–paper insulation is the critical insulation element in the modern power system. Under a harsh operating environment, oil–paper insulation will deteriorate gradually, resulting in electrical accidents. Thus, it is important to evaluate and monitor the insulation state of oil–paper insulation. Firstly, this paper introduces the geometric structure and physical components of oil–paper insulation and shows the main reasons and forms of oil–paper insulation's degradation. Then, this paper reviews the existing condition assessment techniques for oil–paper insulation, such as the dissolved gas ratio analysis, aging kinetic model, cellulose–water adsorption isotherm, oil–paper moisture balance curve, and dielectric response technique. Additionally, the advantages and limitations of the above condition assessment techniques are discussed. In particular, this paper highlights the dielectric response technique and introduces its evaluation principle in detail: (1) collecting the dielectric response data, (2) extracting the feature parameters from the collected dielectric response data, and (3) establishing the condition assessment models based on the extracted feature parameters and the machine learning techniques. Finally, two full potential studies are proposed, which research hotspots' oil–paper insulation and the electrical–chemical joint evaluation technique. In summary, this paper concludes the principles, advantages and limitation of the existing condition assessment techniques for oil–paper insulation, and we put forward two potential research avenues. [ABSTRACT FROM AUTHOR]

The mechanical properties for paper sheets composited with glucose (Glc), methyl cellulose (MC), and carboxymethyl cellulose (CMC) were investigated. The paper composites were prepared by immersing paper sheets in aqueous solutions of these materials and drying at 100 °C for 30 min. The stress–strain curves for these paper composites were measured by a uniaxial tensile apparatus with a stretching speed of 2 mm/min. The breaking stress and strain for untreated paper were 24 MPa and 0.016, respectively. The paper composites demonstrated stress–strain curves similar to the untreated paper; however, the breaking point largely differed for these composites. The breaking strain and breaking stress for the Glc composite slightly decreased and those for the MC composite gradually increased with the concentration of materials composited. Significant increases in the mechanical properties were observed for the CMC composite. The breaking stress, breaking strain, and breaking energy for the 3 wt.% CMC composite were 2.0-, 3.9-, and 8.0-fold higher than those for untreated paper, respectively. SEM photographs indicated that the CMC penetrated into the inner part of the paper. These results strongly suggest that the mechanical improvement for CMC composites can be understood as an enhancement of the bond strength between the paper fibrils by CMC, which acts as a bonding agent. It was also revealed that the breaking strain, breaking stress, and breaking energy for the CMC composites were at maximum at the first cycle and decreased gradually as the immersion cycles increased. [ABSTRACT FROM AUTHOR]

Achieving the desired properties of paper such as strength, durability, and printability remains challenging. Paper mills employ calcium carbonate (CaCO3) as a filler to boost paper's brightness, opacity, and printability. However, weak interaction between cellulose fibers and CaCO3 particles creates different issues in the papermaking industry. Therefore, this study explores the influence of various inorganic additives as crosslinkers such as mesoporous SiO2 nanospheres, TiO2 nanoparticles, h-BN nanoflakes, and hydroxylated h-BN nanoflakes (h-BN-OH) on inorganic fillers content in the paper. They were introduced to the paper pulp in the form of a polyethylene glycol (PEG) suspension to enable bonding between the inorganic particles and the paper pulp. Our findings have been revealed based on detailed microscopic and structural analyses, e.g., transmission and scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and N2 adsorption/desorption isotherms. Finally, the inorganic fillers (CaCO3 and respective inorganic additives) content was evaluated following ISO 1762:2001 guidelines. Conducted evaluations allowed us to identify the most efficient crosslinker (SiO2 nanoparticles) in terms of inorganic filler retention. Paper sheets modified with SiO2 enhance the retention of the fillers by ~12.1%. Therefore, we believe these findings offer valuable insights for enhancing the papermaking process toward boosting the quality of the resulting paper. [ABSTRACT FROM AUTHOR]

Iodine is an essential micronutrient for humans due to its fundamental role in the biosynthesis of thyroid hormones. As a key parameter to assess health conditions, iodine intake needs to be monitored to ascertain and prevent iodine deficiency. Iodine is available from various food sources (such as seaweed, fish, and seafood, among others) and dietary supplements (multivitamins or mineral supplements). In this work, a microfluidic paper-based analytical device (μPAD) to quantify iodide in seaweed and dietary supplements is described. The developed μPAD is a small microfluidic device that emerges as quite relevant in terms of its analytical capacity. The quantification of iodide is based on the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) by hydrogen peroxide in the presence of iodine, which acts as the catalyst to produce the blue form of TMB. Additionally, powder silica was used to intensify and uniformize the colour of the obtained product. Following optimization, the developed μPAD enabled iodide quantification within the range of 10-100 µM, with a detection limit of 3 µM, and was successfully applied to seaweeds and dietary supplements. The device represents a valuable tool for point-of-care analysis, can be used by untrained personnel at home, and is easily disposable, low-cost, and user-friendly.

Though paper is an environmentally friendly alternative to plastic as a packaging material, it lacks antibacterial properties, and some papers have a low resistance to oil or water. In this study, a multifunctional paper-coating material was developed to reduce the use of plastic packaging and enhance paper performance. Natural cellulose nanocrystals (CNCs) with excellent properties were used as the base material for the coating. The CNCs were functionalized into dialdehyde CNCs (DACNCs) through periodate oxidation. The DACNCs were subsequently complexed using erythrosine as a photosensitizer to form an erythrosine–CNC composite (Ery-DACNCs) with photodynamic inactivation. The Ery-DACNCs achieved inactivations above 90% after 30 min of green light irradiation and above 85% after 60 min of white light irradiation (to simulate real-world lighting conditions), indicating photodynamic inactivation effects. The optimal parameters for a layer-by-layer dip coating of kraft paper with Ery-DACNCs were 4.5-wt% Ery-DACNCs and 15 coating layers. Compared to non-coated kraft paper and polyethylene-coated paper, the Ery-DACNC-coated paper exhibited enhanced mechanical properties (an increase of 28% in bursting strength). More than 90% of the bacteria were inactivated after 40 min of green light irradiation, and more than 80% were inactivated after 60 min of white light irradiation. [ABSTRACT FROM AUTHOR]

Flexible paper-based force sensors have garnered significant attention for their important potential applications in healthcare wearables, portable electronics, etc. However, most studies have only used paper as the flexible substrate for sensors, not fully exploiting the potential of paper's micro-nanostructure for sensing. This article proposes a novel approach where paper serves both as the sensitive element and the flexible substrate of force sensors. Under external mechanical forces, the micro-nanostructure of the conductive-treated paper will change, leading to significant changes in the related electrical output and thus enabling sensing. To demonstrate the feasibility and universality of this new method, the article takes paper-based capacitive pressure sensors and paper-based resistive strain sensors as examples, detailing their fabrication processes, constructing sensing principle models based on the micro-nanostructure of paper materials, and testing their main sensing performance. For the capacitive paper-based pressure sensor, it achieves a high sensitivity of 1.623 kPa−1, a fast response time of 240 ms, and a minimum pressure resolution of 4.1 Pa. As for the resistive paper-based strain sensor, it achieves a high sensitivity of 72 and a fast response time of 300 ms. The proposed new method offers advantages such as high sensitivity, simplicity in the fabrication process, environmental friendliness, and cost-effectiveness, providing new insights into the research of flexible force sensors. [ABSTRACT FROM AUTHOR]

Nowadays, the emphasis is on increasing the durability of all products. For this reason, it is also advisable to look into extending the durability of paper products. The main reason for using flax pulp is that flax and cotton pulp are widely used for the production of banknotes due to their higher strength. This paper deals with flax pulp with the addition of nanocellulose, which should further enhance the mechanical properties of the pulp. The tensile strength, breaking length, and tensile energy absorption index were evaluated as the key mechanical properties. At the same time, the effect of the addition of nanocellulose, whether it was added to the pulp mass or applied to the later produced paper as a spray or coating, was tested in comparison to paper without the addition of nanocellulose. The best mechanical properties, i.e., tensile strength, were achieved for the highest addition of 5% of nanocellulose into the pulp, at 24.3 Nm∙g−1, and for the coating application, at 28.7 Nm∙g−1, compared to the flax pulp without the addition, where the tensile strength was 20.5 Nm∙g−1. The results of this research are used for the assessment of nanocellulose as a natural compatible additive to enhance the strength properties of cellulose-based materials. [ABSTRACT FROM AUTHOR]

The growing demand for environmentally friendly and sustainable materials has led to the invention of innovative solutions aiming to reduce negative impacts on the environment. Mycelium-based green composites (MBCs) have become an alternative to traditional materials due to their biodegradability and various potential uses. Although MBCs are accepted as modern materials, there are concerns related to some of their physical and mechanical properties that might have limitations when they are used. This study investigates the effects of using paper waste to improve MBC properties. In this study, we investigated the physical and mechanical properties of MBCs produced from lignocellulosic materials (corn husk and sawdust) and mushroom mycelia of the genus Lentinus sajor-caju TBRC 6266, with varying amounts of paper waste added. Adding paper waste increases the density of MBCs. Incorporating 20% paper waste into corn husks led to the enhancement of the compression, bending, and impact strength of MBCs by over 20%. Additionally, it was also found that the MBCs produced from corn husk and 10% paper waste could help in reducing the amount of water absorbed into the material. Adding paper waste to sawdust did not improve MBC properties. At the same time, some properties of MBCs, such as low tensile strength and high shrinkage, might need to be further improved in the future to unlock their full potential, for which there are many interesting approaches. Moreover, the research findings presented in this publication provide a wealth of insightful information on the possibility of using paper waste to improve MBC performance and expand their suitability for a range of applications in sustainable packaging materials and various home decorative items. This innovative approach not only promotes the efficient utilization of lignocellulosic biomass but also contributes to the development of environmentally friendly and biodegradable alternatives to traditional materials. [ABSTRACT FROM AUTHOR]

The widespread use of mobile devices and laptops has replaced traditional paper-based learning and the question of how the brain efficiency of digital tablet-based learning differs from that of paper-based learning remains unclear. The purpose of this study was to investigate the difference in brain efficiency for learning between paper-based and digital tablet-based learning by measuring activity in the prefrontal cortex (PFC) using functional near-infrared spectroscopy. Thirty-two subjects were randomly assigned to the paper-based learning or the digital tablet-based learning group. Subjects in each group performed a memory task that required memorizing a three-minute novel (encoding phase) on a paper or digital tablet, followed by a test in which they answered four multiple-choice questions based on the novel's content. To compare both groups, behavioral performance on the test (retrieval phase) and activity in the PFC were measured. As a result, no significant difference in behavioral performance between both groups was observed (p > 0.05). However, the paper-based learning group showed significantly lower activity in the PFC in the encoding phase than the digital tablet-based learning group (p < 0.05) but not in the retrieval phase. The current study demonstrated that brain efficiency in encoding is higher in subjects with paper-based learning than those with digital tablet-based learning. This finding has important implications for education, particularly in terms of the pros and cons of electronic document-based learning. [ABSTRACT FROM AUTHOR]

In recent years, due to environmental awareness regarding the harmfulness of polymeric materials, there has been a growing interest in using papers, especially those from alternative raw materials. The importance of using all available raw materials is imperative today. Raw materials that were once viewed as waste are now of great importance because they have the ability to replace raw materials that are used irrationally or are lacking. Cereal straw is a lignocellulosic material that could be used in the paper industry and in the production of increasingly prevalent paper packaging. The aim of this research was to analyze the relationships between the qualitative parameters of straw-based printed papers containing 30% agricultural residues (wheat, barley, or triticale). The influence of two qualitative parameters (ink penetration depth and optical ink density) on the print-through was observed using multiple regression analysis on straw-based papers produced at the laboratory level. Throughout the research, 100% recycled wood paper was used as a reference sample. The results of the regression analysis showed that none of the variables individually make a statistically significant contribution to the prediction of the dependent variable in a linear context, that is, they indicate a non-linear interaction between the variables and the specific conditions under which the dependent variable reaches local extremes and changes in the gradient. Considering the results of the regression analysis and the visualization of the relationship, the model was additionally tested with other independent variables (paper type). From the results obtained, it can be concluded that the alternative straw-based paper with 30% barley pulp has the best interaction between ink and paper, which is the most similar to the reference sample in terms of printability, while the alternative straw-based paper with 30% wheat generally differs significantly from the reference paper when all three prints are considered. [ABSTRACT FROM AUTHOR]

Environmental pollution is a significant problem and is increasing gradually as more and more harmful pollutants are being released into water bodies and the environment. Water pollutants are dangerous and pose a threat to all living organisms and the ecosystem. Paper waste is one of the most widespread and largest wastes in the world. This research aims to address two important problems simultaneously: the reduction in solid waste in the environment using activated carbon from paper waste as potential adsorbents and the removal of harmful contaminants from water. Carbon from paper waste was activated with H2O2, HNO3, and KMnO4 for the adsorption of Cr(VI) and MB. SEM, EDX, FTIR, Raman, and BET were used to determine the properties of the materials. The surface morphology of the materials consisted of amorphous particles. EDX shows that all activated samples have a higher content of (O) than carbon paper waste. Adsorption studies showed that there was a stronger interaction between the pollutants and the adsorbent at a higher initial concentration (200 mg/L) than at the lower initial concentrations. The contact time data show that uptake increases when the interaction time between the contaminant and the adsorbent is increased. The tests for the pH of the solution show that the adsorption of Cr(VI) decreases when the pH is gradually increased, whereas the adsorption of MB increases when the pH of the solution is increased. The results fit better with the Freundlich isotherm and PSO models. The temperature studies show that the enthalpy was positive, indicating that the uptake process is endothermic. The Gibbs free energy values were all negative, indicating that adsorption between the adsorbents and the pollutants was favored. After four consecutive cycles, all the samples retained more than 60% of their uptake capability. [ABSTRACT FROM AUTHOR]

Background: The pulp and paper industry (P&PI) is undergoing significant disruption driven by global megatrends that necessitate advanced tools for predicting future behavior and adapting strategies accordingly. Methods: This work utilizes a multi-criteria framework to quantify the effects of digitalization, changes in social behavior, and sustainability as three major megatrends transforming the P&PI industry, with a specific focus on hygiene tissue products. Thus, the research combines a comprehensive literature review, insights from a Delphi study, and topic modeling to qualitatively and quantitatively assess the present and future impacts of these global megatrends. Results: The findings suggest an urgent need to identify alternative raw materials to prevent potential supply chain disruptions. Moreover, due to shifts in social behavior, it becomes critical for businesses to substantiate their sustainability claims with hard data to avoid the risk of a "greenwashing" perception among consumers. Conclusions: This study provides decision support for strategic planning by highlighting actionable insights, quantitative predictions, and trend analysis, alongside the examination of consumer and market trends. It aims to incorporate diverse stakeholder perspectives and criteria into decision-making processes, thereby enriching the strategic planning and sustainability efforts within the P&PI industry. [ABSTRACT FROM AUTHOR]

As power sources for Internet-of-Things sensors, thermoelectric generators must exhibit compactness, flexibility, and low manufacturing costs. Stretchable and flexible painted thermoelectric generators were fabricated on Japanese paper using inks with dispersed p- and n-type single-walled carbon nanotubes (SWCNTs). The p- and n-type SWCNT inks were dispersed using the anionic surfactant of sodium dodecylbenzene sulfonate and the cationic surfactant of dimethyldioctadecylammonium chloride, respectively. The bundle diameters of the p- and n-type SWCNT layers painted on Japanese paper differed significantly; however, the crystallinities of both types of layers were almost the same. The thermoelectric properties of both types of layers exhibited mostly the same values at 30 °C; however, the properties, particularly the electrical conductivity, of the n-type layer increased linearly, and of the p-type layer decreased as the temperature increased. The p- and n-type SWCNT inks were used to paint striped patterns on Japanese paper. By folding at the boundaries of the patterns, painted generators can shrink and expand, even on curved surfaces. The painted generator (length: 145 mm, height: 13 mm) exhibited an output voltage of 10.4 mV and a maximum power of 0.21 μW with a temperature difference of 64 K at 120 °C on the hot side. [ABSTRACT FROM AUTHOR]

Nucleic acid quantification, allowing us to accurately know the copy number of target nucleic acids, is significant for diagnosis, food safety, agricultural production, and environmental protection. However, current digital quantification methods require expensive instruments or complicated microfluidic chips, making it difficult to popularize in the point-of-care detection. Paper is an inexpensive and readily available material. In this study, we propose a simple and cost-effective paper membrane-based digital loop-mediated isothermal amplification (LAMP) method for nucleic acid quantification. In the presence of DNA fluorescence dyes, the high background signals will cover up the amplicons-formed bright spots. To reduce the background fluorescence signals, a quencher-fluorophore duplex was introduced in LAMP primers to replace non-specific fluorescence dyes. After that, the amplicons-formed spots on the paper membrane can be observed; thus, the target DNA can be quantified by counting the spots. Take Vibrio parahaemolyticus DNA detection as an instance, a good linear relationship is obtained between the light spots and the copy numbers of DNA. The paper membrane-based digital LAMP detection can detect 100 copies target DNA per reaction within 30 min. Overall, the proposed nucleic acid quantification method has the advantages of a simple workflow, short sample-in and answer-out time, low cost, and high signal-to-noise, which is promising for application in resourced limited areas. [ABSTRACT FROM AUTHOR]

This research explores the potential of ionic liquids (ILs) in restoring paper artifacts, particularly an aged book sample. Three distinct ILs—1-ethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide, 1-methyl-3-pentylimidazolium bis(trifluoromethylsulfonyl)imide, and 1-methyl-3-heptylimidazolium bis(trifluoromethylsulfonyl)imide —both in their pure form and isopropanol mixtures, were examined for their specific consumption in conjunction with paper, with 1-ethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide displaying the highest absorption. Notably, the methyl-3-heptylimidazolium ionic liquid displayed pronounced deacidification capabilities, elevating the paper pH close to a neutral 7. The treated paper exhibited significant color enhancements, particularly with 1-heptyl-3-methylimidazolium and 1-pentyl-3-methylimidazolium ILs, as evidenced by CIE-Lab* parameters. An exploration of ILs as potential UV stabilizers for paper unveiled promising outcomes, with 1-heptyl-3-methylimidazolium IL demonstrating minimal yellowing post-UV irradiation. FTIR spectra elucidated structural alterations, underscoring the efficacy of ILs in removing small-molecular additives and macromolecules. The study also addressed the preservation of inked artifacts during cleaning, showcasing ILs' ability to solubilize iron gall ink, particularly the one with the 1-ethyl-3-propylimidazolium cation. While exercising caution for prolonged use on inked supports is still recommended, ILs are shown here to be valuable for cleaning ink-stained surfaces, establishing their effectiveness in paper restoration and cultural heritage preservation. [ABSTRACT FROM AUTHOR]

Featured Application: Papermaking and printing industry, usability, i.e., legibility of printed text. Invasive alien plant species (IAPS) may cause threats to native biodiversity in ecosystems. Researchers have been investigating all the possible ways that they can be used effectively for other purposes. Since IAPS are capable of forming cellulose fibre nets, in this research, papers were made from three different types of IAPS (Japanese knotweed, giant goldenrod, and black locust). This research examined these IAPS papers and their effectiveness when used as printing substrates. In comparison to commercial office paper, the differences in basic, surface, optical, and microscopic properties were measured. As a widely used technology, inkjet printing was applied. We tested a commonly used sans-serif typeface (which has been established as being more legible than other typefaces in previous research) in three different type sizes (i.e., 8, 10, and 12 pt). According to the results, paper made from IAPS could offer some usable properties and acceptable legibility, especially when printing typefaces with specific attributes, such as moderate counter size, higher x-height, and minimal differences in the letter stroke width, are used. An appropriate typographic tonal density should be achieved in combination with an adequate letter size, e.g., 10 pt type size when a sans-serif typeface is used. [ABSTRACT FROM AUTHOR]

In the present study, an environmentally friendly oil- and water-resistant paper was developed using a holo-lignocellulosic nanofibril (LCNF)-based composite coating. The LCNF was prepared from wheat straw using a biomechanical method. Characterizations of oil- and water-resistant coated paper and the effect of LCNF content on the performance of the coated paper were confirmed by combining contact angle analysis, Cobb 300s, and mechanical performance tests. The results show that the barrier performance and mechanical strength of the coated paper were greatly improved with the increase of LCNF content. The contact angle of oil and water of coated paper containing 50% LCNF were 69° and 78°, respectively, while the contact angle of oil and water of the base paper were only 30° and 20°, respectively. Cobb 300s values reduced from 110 g/m2 to 30 g/m2 when the LCNF content increased from 50% to 90%. Moreover, under the coating amount of 20 g/m2, the tensile strength of the coating paper was 0.980 KN/m, an increase of 10.11% compared with the base paper. The bursting strength reached 701.930 KPa, which was 10.75% higher than the base paper. In short, it is feasible to prepare LCNF from wheat straw, and apply it to produce water-proof and oil-proof paper. The water-proof and oil-proof paper developed in this study not only offers a novel approach to addressing white pollution but also presents a new research avenue for exploring the potential applications of agricultural waste. [ABSTRACT FROM AUTHOR]

Alternanthera philoxeroides and Hypophthalmichthys molitrix offer significant nutritional benefits. This study evaluates the proximate composition, amino acid profile, GC-MS analysis, FT-IR spectroscopy, SEM and EDX, and color values of edible paper sheets (EPSs) derived from Alternanthera philoxeroides incorporating different levels of Hypophthalmichthys molitrix flesh. The protein content in the EPSs varied based on fish flesh incorporation, peaking at 52.66% in Ap100/Hm300 (Non-boil). Protein and carbohydrate contents showed an inverse correlation across EPSs, with the highest carbohydrate content of 60.89% in sample Ap400/Hm0 (Boil). Lipid content was also found to correlate with H. molitrix flesh content in EPSs, ranging from 1.59% to 18.41%. Amino acid analysis identified 11 types, with methionine as the most prevalent, followed by leucine, phenylalanine, and lysine. GC-MS analysis revealed 51 bioactive compounds, including carbonic acid, hentriacontane, and various fatty acids. FT-IR analysis showed characteristic bonds, while color analysis displayed L* values ranging from 24.37 to 30.97. SEM analyses depicted the microstructure, surface view, and elemental composition of the EPSs, and EDX showed an abundance of Ca, N, K, O, C, Mg, Na, P, Cl, Mn, and Fe. Therefore, EPSs prepared from A. philoxeroides and H. molitrix could offer a promising approach for effectively utilizing aquatic biomass and providing both plant and animal nutrients to consumers. [ABSTRACT FROM AUTHOR]