Search

This paper presents an energy‐efficient digital‐to‐analog converter (DAC) switching method with low common‐mode variations for high‐resolution successive approximation register (SAR) analog‐to‐digital converters (ADCs), while enabling to implement resolutions such as 14‐bit as compared to the typical 10‐bit. The proposed switching method enables high resolution by having a nearly constant common‐mode voltage and employing input‐swapping to use the reference voltage (Vref) only in the sampling phase. This method eliminates the need for the third reference voltage during the entire DAC switching steps, which reduces the required number of switches at the bottom plates of the capacitors. The use of lower number of switches not only lowers the DAC control logic complexity, but also results in a faster operation, lower power, and smaller area. When compared to conventional 10‐bit SAR ADCs, the proposed switching method in a 10‐bit implementation reduces the average energy and area by 96.09% and 75%, respectively, while offering high‐resolution implementation options such as 14 bits. [ABSTRACT FROM AUTHOR]

This paper presents a novel dynamic bias latch‐type comparator combined with a voltage‐controlled delay line (VCDL), designed specifically for low‐power and low‐noise applications in high‐speed analog‐to‐digital converters (ADCs). The incorporation of the VCDL precedes the dynamic bias amplifier in the proposed comparator, thereby achieving a balance between energy efficiency and high‐speed operation. This innovative design enhances the input common voltage of the dynamic bias amplifier through the utilization of the VCDL, surpassing that of a conventional dynamic bias comparator. Furthermore, it demonstrates increased adaptability in technology scaling and efficient operation at lower supply voltages, leveraging inverters and other simple cells. The proposed comparator in 28 nm process technology achieves a 309.7 µV input‐referred noise while consuming approximately 145.8 fJ and completing comparisons in 125 ps with a 0.9 V supply and a 0.45 V input common‐mode voltage. [ABSTRACT FROM AUTHOR]

This paper presents an artificially intelligent Flash ADC with enhanced resolution from 4 to 10 bits. Unlike conventional approaches, this artificial intelligence (AI)‐based architecture avoids the use of many number of comparators in the Flash ADC when the ADC's resolution changes from 4 to 10 bits. This work initially gets the digital output of a 4‐bit existing Flash ADC as a training data set and then uses these 4‐bit output bits and sends to resolution enhancement logic (REL) block to vary its resolution without increasing the hardware complexities. After simulation, it is observed that the proposed ADC is of SNR of 24.13 dB for 4‐bit Flash ADC designed in SCL 180 nm CMOS technology and increases from 36.89 to 60.70 dB for 6 to 10‐bit resolution, respectively. The sampling frequency of the proposed architecture ranges from 3.6 to 1.04 GHz for a change in resolution from 4 to 10 bits. The FoM of 235 fJ/conv‐step in the training phase is obtained, and it varies from 56 to 20.3 fJ/conv‐step in the next phase of the testing and the prediction. The estimated area of the proposed 4‐to‐10‐bit variable resolution Flash ADC is 235.23×301.67 μm2. [ABSTRACT FROM AUTHOR]

Summary: In this paper, a low‐power transconductor‐capacitor (Gm‐C) filter with programmable cutoff frequency is designed for electroencephalogram (EEG), electrocardiogram (ECG), and surface electromyography (sEMG) biosignals. The second‐order Butterworth low pass filter (LPF) is designed as an interface between an instrumentation amplifier (IA) and an analog‐to‐digital converter (ADC). The proposed Gm‐C filter suppresses out‐of‐band components and also plays an anti‐aliasing role. With the variable transconductance based on flipped voltage follower (FVF), the cutoff frequencies of 100 Hz, 560 Hz, and 1.5 kHz are obtained for EEG, ECG, and sEMG, respectively. This structure is highly accurate by using a robust and low‐power common mode feedback (CMFB). With 0.8 V supply voltage, the total power consumption of the filter is only 56 nW, 100 nW, and 221 nW for cutoff frequencies of 100 Hz, 560 Hz, and 1.5 kHz, respectively. The proposed Gm‐C filter is simulated in TSMC 65 nm CMOS technology and occupies an area of 0.12 mm2. The figure of merit (FOM) of the proposed filter is equal to 1.9 pW/pole. [ABSTRACT FROM AUTHOR]

Equivalent‐time sampling can improve measurement or sensing systems because it enables a broader frequency band and higher delay resolution for periodic signals with lower sampling rates than a Nyquist receiver. Meanwhile, a digital down‐conversion (DDC) technique can be implemented using a straightforward radio frequency (RF) circuit. It avoids timing skew and in‐phase/quadrature gain imbalance instead of requiring a high‐speed analog‐to‐digital converter to sample an intermediate frequency (IF) signal. Therefore, when equivalent‐time sampling and DDC techniques are combined, a significant synergy can be achieved. This study provides a parameter design methodology for optimal equivalent‐time sampling using DDC. [ABSTRACT FROM AUTHOR]

This letter presents a low‐power single‐slope analog‐to‐digital converter (ADC) for column‐parallel architectures. A simple and effective design technique is proposed to solve the input‐dependent power consumption problem of the conventional single‐slope ADCs. A decision‐feedback loop is implemented in the second stage of the comparator. Based on the negative‐feedback path, which is activated after the signal decision of the comparator, the input‐dependent dynamic current path in the amplifier is disabled. Furthermore, an additional low‐power design technique is proposed to save the power consumption of the ADC by optimizing the offset cancelling auto‐zero period. With the combination of the proposed techniques, the power consumption of the single‐slope ADC can be effectively saved while suppressing the dynamic current. [ABSTRACT FROM AUTHOR]

This article presents a design of a VCO‐based ADC based on n‐type metal oxide thin‐film transistor (TFT). The TFTs are fabricated on a glass substrate using Indium Zinc Oxide technology. The VCO‐based ADC consists of a VCO, a level shifter and a sampling circuit, while the VCO is composed of a charge‐discharge cell and an inverter chain. The ADC has a 1.464 mm 2 area, 0.89 mW power consumption, an output frequency range of 1.41 KHz/V tuning sensitivity, 1.8% maximum linear error and achieves a SNDR of 34.2 dB in the case of an input signal of 1.5 Hz and a sampling rate of 20 S/s. [ABSTRACT FROM AUTHOR]