Search

Background: Previously, there has been some work in the field of optical imaging on phase compensation by employing Legendre polynomials as an expansion of the phase function, and this seems to be an appealing unstudied area in the field of ultrasound imaging. Purpose: The paper is devoted to solving one of the problems of enhancing the authenticity of diagnostics data obtained in ultrasound visualization systems and presents a novel approach to aberration correction, which ensures a reliable eliminating of phase distortions. The novelty of the proposed approach consists in the use of the decomposition of the wave front by Legendre polynomials to approximate aberrations of the phase front of ultrasonic waves propagating through distorting layers. Methods: The phase aberrations are corrected using a single sector probe that captures echoes in synthetic aperture mode. The proposed method approximates the changes in the wave front by means of the Legendre polynomials. The performance was investigated by placing a 13‐mm‐wide ultrasonic probe with 64 elements operating at 2 MHz on the surface of a commercial quality control phantom ATS Model 539 through a distorting layer. The following metrics were measured: peak value, root mean square (RMS), full width at half maximum (FWHM), contrast‐to‐noise ratio (CNR). During the experiments, three different aberrators were used interchangeably as distorting layers, two of which were made of photopolymer resin with RMS values of 39 and 97 ns and a speed of sound close to that of a human temporal bone tissue, and the third was an ex vivo human temporal bone with the RMS value of 44 ns. To test the correction, three regions inside the phantom were examined. Two‐sided nonparametric Wilcoxon rank‐sum test was used for assessing the statistical significance. The significance level for this study was set at α ≤ 0.05. To counteract the problem of multiple comparisons, the p‐values were adjusted by the Holm–Bonferroni correction method. Results: The statistically significant results have demonstrated the possibility of increasing peak intensity value up to 3.08 times, reducing the RMS width and FWHM of the intensity angular distribution down to 60% and 82%, respectively, and increasing CNR up to 2.12 times by using the proposed phase distortion correction method, compared with the case without correction. The results show that the method can be used as an effective aberration correction technique for all tested regions inside the phantom and distorting layers. Its usage allowed correcting up to 97% of the aberrations caused by the ex vivo temporal bone model. Conclusion: The results show that the usage of the proposed method for aberration correction can successfully increase the intensity and reduce the angular width of the ultrasound wave scattered by the point targets inside the phantoms. The method works with different distorting layers and is capable of correcting phase aberrations in multiple sections of the sonogram. The limitation of the proposed method consists in the fact that it requires the use of aperture synthesis and access to raw radiofrequency data, which restricts its application in common scanners. [ABSTRACT FROM AUTHOR]

Diffusion bonding technology is widely used in the connection of precision components, yet accurately and reliably detecting contact-type defects on the bond interface still remains a significant problem. Nonlinear ultrasonic methods have been proven to be sensitive to contact-type defects; however, the use of continuous wave or tone burst wave excitation limits its wider application. In this paper, dual-probe nonlinear ultrasonic testing with pulse wave excitation is proposed to detect contact-type defects in diffusion-bonded joints. A titanium alloy diffusion-bonded specimen with artificial defects was fabricated, and the corresponding detection device was designed based on the existing ultrasonic C-scan testing system. A C-scan imaging program based on nonlinear parameters was developed by extracting the fundamental and second harmonic waves of the reflection echo on the bond interface. The results demonstrated that the proposed detection scheme can obtain the nonlinear parameters of diffusion-bonded interfaces, and the nonlinear ultrasonic C-scan image of the bond interface is also obtained. The nonlinear parameter in the contact-type defects areas calculated from the bond interface echo is about 10 times (20 dB) higher than that in macro defects areas, whose gap is about 10 μm. The results indicate that the nonlinear ultrasonic methods seem to be more sensitive to contact-type defects and have a great potential to complement the insufficient detection capability of linear ultrasound for diffusion-bonded joints. [ABSTRACT FROM AUTHOR]

The ultrasonic echo technique is widely used in non-destructive testing (NDT) of concrete objects for thickness measurements, geometry determinations and localization of built-in components. To improve ultrasonic imaging of complex concrete structures, we transferred a seismic imaging technique, the Reverse Time Migration (RTM), to NDT in civil engineering. RTM, in contrast to the conventionally used synthetic aperture focusing technique (SAFT) algorithms, considers all wavefield types and thus, can handle complex wave propagations in any direction with no limit on velocity variations and reflector dip. In this paper, we focused on the development, application and evaluation of a two-dimensional elastic RTM algorithm considering horizontally polarized shear (SH) waves only. We applied the elastic SH RTM routine to synthetic ultrasonic echo SH-wave data generated with a concrete model incorporating several steps and circular cavities. As these features can often be found in real-world NDT use cases, their imaging is extremely important. By using elastic SH RTM, we were able to clearly reproduce almost all reflectors inside the concrete model including the vertical step edges and the cross sections of the cavities. We were also capable to show that more features could be mapped compared to SAFT, and that imaging of complex reflectors could be sharpened compared to elastic P-SV (compressional-vertically polarized shear) RTM. Our promising results illustrate that elastic SH RTM has the potential to significantly enhance the reconstruction of challenging concrete structures, representing an important step forward for precise, high-quality ultrasonic NDT in civil engineering. [ABSTRACT FROM AUTHOR]

Within the framework of a simple model of the sensitivity function, the Doppler spectra are considered for different ways of generating response signals using plane wave compounding. A Doppler spectrum is obtained for coherent compounding of signals received at different steering angles of waves during their period of changing. Compared to traditional diagnostic systems, the Doppler spectrum width is increased only by limiting the duration of the signals. There is no additional increase in the spectrum width if the compound signals are formed by adding with cyclic permutation, in which signals from each new wave angle are compounded. When a Doppler signal is formed directly from Doppler signals at different steering angles, the spectral width increases both in comparison with the traditional method of sensing with stationary focused ultrasound fields and with the case of coherent signal compouding. The obtained increase in the spectral width has an intrinsic physical meaning. The increase in width is connected with a dynamic change in the Doppler angle, which increases the interval of apparent projections of the velocities of motion of inhomogeneities along the direction of transmitting of a plane wave without inclination. [ABSTRACT FROM AUTHOR]

• The multi-mode laser ultrasonic F-SAFT and F-TFM imaging have realized. • The frequency-domain imaging results were weighted by phase circular statistical vector factor. • Achieved blind spot free images of the minimum 0.3 mm transverse hole defect. • Continuous scanning frequency-domain imaging of multiple defects verified the detection ability. Far-field laser technology has greatly promoted the progress of nondestructive ultrasonic imaging of bulk structures. However, under thermoelastic excitation, the body waves exhibit a relatively low signal-to-noise ratio, resulting in images with low resolution and contrast. Based on the motivation, this paper developed a frequency-domain phase weighted imaging method to improve the quality of laser ultrasonic defect imaging. Firstly, laser ultrasonic scanning was performed on the sample with artificial transverse hole defects. The cylindrical lens focused line source was used to improve the intensity of the body wave signals, and ensure that there was no damage on the material surface under high laser energies. Then, the frequency-domain phase shift migration (PSM) algorithm was used to perform multimode imaging of defects, achieving frequency-domain synthetic aperture focusing technique (F-SAFT) and total focused method (F-TFM) imaging based on full matrix capture. Furthermore, the phase circular statistical vector (PCSV) was proposed for weighted optimization, which improved the image quality, suppressed the background noise and multimode artifacts. Finally, the imaging quality of several algorithms were discussed. The results indicate that frequency-domain images were superior to time-domain results. After phase weighting, the imaging quality can be further improved, and the detection blind zone was significantly reduced. This work will contribute to the rapid and high-quality defect imaging of laser ultrasonic. [ABSTRACT FROM AUTHOR]

Periodic inspection of concrete structures for detecting internal defects through nondestructive imaging is recommended for ensuring structural safety and integrity. Ultrasonic imaging is one of the emerging and widely accepted techniques in nondestructive diagnostics of concrete structures. However, manually screening the ultrasonic images to detect and localize anomalies over large areas especially those from public infrastructure is tedious and prone to misjudgments. This work proposes a Region-based CNN to automatically detect, localize, and segment those signatures corresponding to defects from the noisy ultrasonic images with multiple features. This network replaces the conventional RoI pooling adopted in RCNNs with RoIAlign. To optimize the model for real-life complexity and noise levels, the network is trained on real experimental data. The ultrasonic image dataset has been generated by applying the imaging technique based on the Synthetic Aperture Focusing Technique on reflected waveform data obtained on various specimens with installed defects. The proposed network has been trained on the labelled image dataset containing signatures corresponding to multiple flaws like debonded rebars, delaminations, and planar crack-like defects in concrete members. The predictions of the trained model over the test datasets detect and masks the pixels corresponding to defects in ultrasonic images with a best mAP of 0.98. Segmentation results of the developed model upon testing are found superior to other state-of-the-art defect detection networks. • Presents a two-stage Convolutional Network for automatic detection and segmentation of defects in ultrasonic images. • First CNN-based model to segment defects in ultrasonic images of Reinforced Concrete. • Model trained on images with intact rebars in concrete, debonded concrete-rebar interfaces, delaminations, and inclined defects. • The model during testing recorded accuracies of 98% & 85% on clean and artifact-filled test sets, respectively. • Predictions from the proposed masking model are superior to those from the one-stage detector model on the same datasets. [ABSTRACT FROM AUTHOR]

Ultrasonic testing is widely used in the industrial field because of its high sensitivity, safety and low-cost, which plays an increasingly important role in detecting defects on industrial. However, at present, defect detection only stays in scanning surface defects and classifying the internal defects of the specimen. The accuracy of quantitative imaging of the morphology of the internal defects of the specimen is still an issue to be improved. In this paper, the simple defects in several specimens are detected by ultrasound based on finite element simulation software and the accuracy of the signal can be verified by ultrasonic experiment. Then, the features can be extracted by signal processing method. The neural network imagines the inversion results with the Gaussian weight function fusion model. Finally, this paper uses the signals of simple shape defects as the training set to detect the shapes of complex defects and obtain the corresponding imaging results. • The defect detection using moving ultrasonic A-scan testing and signal processing. • Defect image inversion by neural network and Gaussian weight data fusion algorithm. • Complex defect inversion by learning the features of simple defects. [ABSTRACT FROM AUTHOR]

• DAS and DMAS responded differently to changes in f-number. • DAS showed a tradeoff in spatial resolution when optimizing contrast. • DMAS did not show the same tradeoff as DAS when optimizing contrast. • DAS typically outperformed DMAS for image contrast. • DMAS typically outperformed DAS for spatial resolution. The choices of transmit and receive f-numbers impact both ultrasound image contrast and spatial resolution. Although previous studies have evaluated the impact of receive f-number in delay-and-sum (DAS) plane wave imaging, there has not been a systematic study of f-numbers in DAS or delay-multiply-and-sum (DMAS) synthetic aperture (SA) imaging. In this study, we measured the impact on main lobe to side lobe energy ratio (MSER), generalized contrast-to-noise ratio (gCNR), and spatial resolution when varying receive and transmit f-numbers from 1 to 5 in 0.2 increments in DAS and DMAS reconstructed SA images. A wire target in a water tank and a standard imaging phantom were used to measure these metrics. From the water tank wire target images, higher MSER values were achieved with middle-range transmit f-numbers (2–4) and high receive f-numbers (>4) for both DAS and DMAS. From the phantom contrast target images, DAS produced images with high gCNR when using high transmit f-numbers (>4) and high receive f-numbers (>4). This came at the cost of reduced spatial resolution. DMAS produced images with high gCNR when using low transmit f-numbers (<3) and high receive f-numbers (>4). DMAS was not found to have as severe of a tradeoff in spatial resolution when seeking maximum gCNR. However, gCNR was typically lower for DMAS than DAS. For both DAS and DMAS, point target images had high spatial resolution when using low receive f-numbers (<2). Spatial resolution was typically higher for DMAS than DAS. Hanning apodization was found to produce similar trends as those found with rectangular apodization. These findings give insight on the behaviors of DAS and DMAS SA reconstruction algorithms and could be used to guide f-number selection. [ABSTRACT FROM AUTHOR]

A laser ultrasonics (LU) based frequency domain synthetic aperture focusing technology (LUB-F-SAFT), which uses 2D equivalent velocity (SEV) and fuses multi-mode ultrasound, is developed to image the internal horizontal hole defects with a diameter of ∼ 1. 0 mm in bimetallic composites. Bulk waves non-destructively excited by a line-shaped laser are detected by a vibrometer away from the excitation. The results indicate that the LUB-F-SAFT with SEV can improve the imaging quality and locating capability, and the testing error is about 0. 02 mm. The improvement in the imaging quality using SEV for different ratios of the first layer thickness to defect-to-interface distances is discussed. In addition, a theoretical approach based on the directionality of the detected ultrasound is applied to determine a reasonable excitation-detection distance for better defect imaging. A LUB-F-SAFT imaging combining multi-mode waves is employed to improve the range of defect profiles. The results show that the range of the imaged defect profile becomes larger using the multi-mode fused LUB-F-SAFT imaging, which is an improvement of about 49.2% compared to the shear wave imaging result. • LUB-F-SAFT imaging with SEV is developed for bilayer media. • The SEV corrects distortion and position bias of defect. • A optimized excitation-detection distance for better defect imaging. • A multi-mode fused LUB-F-SAFT improve the profile of the defect. [ABSTRACT FROM AUTHOR]