Search

Pump As Turbine (PAT) utility represents a major advance in the field of hydraulic engineering. This work aims to improve the PAT performance characteristics. The sharp impeller leading edge (original impeller) was revealed by flow analysis as exhibiting negative effects on the PAT performances due to flow separation and flow misalignment. The performances of rounded and original impeller leading edge were studied by Computational Fluid Dynamic (CFD) method carried out on ANSYS CFX. Although impeller leading edge rounding has notably improved the performances in off design conditions, the difference of efficiency between the both impeller types was decreasing when increasing the discharge. The hydraulic head generated by the rounded impeller leading edge was also slightly higher at part load conditions, but when increasing the discharge, the difference between the both heads became negligible. It appeared from numerical simulations that the impeller leading edge rounding allows to decrease the hydraulic losses of the individual sub-domains except the outlet pipe. For the seek of a comprehensive analysis, the significant losses were computed for the two impeller geometries. It was observed that the shock losses and swirling losses of the rounded impeller leading edge were lower at part load conditions, but when increasing the discharge, the both losses were lower for the original impeller geometry. The rounded impeller leading edge exhibited as well lower wall frictional losses for the entire operating range of discharge., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Author(s).)

The current centralized configuration of the ammonia industry makes the production of nitrogen fertilizers susceptible to the volatility of fossil fuel prices and involves complex supply chains with long-distance transport costs. An alternative consists of on-site decentralized ammonia production using small modular technologies, such as electric Haber-Bosch or electrocatalytic reduction. Here we evaluate the cost-competitiveness of producing low-carbon ammonia at the farm scale, from a solar agrivoltaic system, or using electricity from the grid, within a novel global fertilizer industry. Projected costs for decentralized ammonia production are compared with historical market prices from centralized production. We find that the cost-competitiveness of decentralized production relies on transport costs and supply chain disruptions. Taking both factors into account, decentralized production could achieve cost-competitiveness for up to 96% of the global ammonia demand by 2030. These results show the potential of decentralized ammonia technologies in revolutionizing the fertilizer industry, particularly in regions facing food insecurity., (© 2024. The Author(s).)

Interest of Pump as Turbine (PAT) is growing with diverse applications in engineering. Usually, the data of PATs are not available in the hands of pump manufacturers. Therefore, performance prediction methods appear as an important research area of PATs. The current prediction methods reposed on expensive, inaccurate and time consuming experimental methods. In the scope of this work, a generic and robust prediction method is built up for a centrifugal impeller PAT. The most significant hydraulic losses were derived in PAT mode, these are namely, the shock losses at the impeller inlet, the swirling losses at the impeller outlet and the impeller wall frictional losses. The Euler head, the available total head and the hydraulic efficiency were computed as well. The global efficiency was computed taking into account the machine mechanical and volumetric efficiencies, enabling therefore to perform comparison of the new prediction method with experimental, computational fluid dynamic (CFD), Rossi and Perez performances prediction methods. From where it resulted a good agreement between the given prediction methods for the entire range of operation, confirming the robustness and the applicability of the developed prediction method. The relative difference between the new prediction method and CFD data and between the new prediction method and experimental data remained higher for lower discharge conditions, notably for extreme part load conditions, where a small error could result in very high relative difference., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Authors.)

Hydrokinetic Banki turbines present an affordable, technically feasible, environmentally friendly technology. Their construction without requiring more expensive structures like diversion weirs, canals, forebay, and penstock, makes their initial investment much lower than commonly used horizontal Banki turbine of the same capacity. The possibility to install in the existing canals for Ultra Low Head applications is the additional motivating factor for this research. The system studied includes two Banki runners without internal shafts mounted vertically side by side surrounded by nozzle and diffuser structures. In the first scenario, Nozzle and then the Nozzle-diffuser augmented structures were separately studied to enhance the output of the runner for ultra-low head application, and the effects of each on the speed, pressure, and power output were analyzed. For the case of commonly used Banki, without nozzle and diffuser augmentation the speed for Ultra Low Head was minimum and determined to be 344 rpm, which is far below the recommended value of 800 rpm for safe operation at a flow rate of 1 m^3/s. In view of this, in the present study the enhanced speed on account of improvement was found to be 850 rpm and 1025 rpm for the design without and with diffuser assemblies respectively. Besides, the performance is seen to be improved by 7.6% with the diffuser as compared with the one without diffuser assembly. Detailed simulation results are presented and discussed: 3D ANSYS-FLUENT optimization result provided optimum number of blades for each runner to be 19 and with the optimum throat width in both cases as 202 mm. On account of the lack of any results reported so far for this innovative geometry, validation of the simulated results was carried out with reported results for the dual horizontal axis Banki turbines with good agreement., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 Published by Elsevier Ltd.)

We highlight the critical role of data in developing sustainable combustion technologies for industries requiring high-density and localized energy sources. Combustion systems are complex and difficult to predict, and high-fidelity simulations are out of reach for practical systems because of computational cost. Data-driven approaches and artificial intelligence offer promising solutions, enabling renewable synthetic fuels to meet decarbonization goals. We discuss open challenges associated with the availability and fidelity of data, physics-based numerical simulations, and machine learning, focusing on developing digital twins capable of mirroring the behavior of industrial combustion systems and continuously updating based on newly available information., Competing Interests: The authors declare no competing interests., (© 2024 The Author(s).)