Search

Lithium niobate (LiNbO3) single crystals are a kind of ferroelectric material with a high piezoelectric coefficient and Curie temperature, which is suitable for the preparation of piezoelectric pressure sensors. However, there is little research reporting on the use of LiNbO3 single crystals to prepare piezoelectric pressure sensors. Therefore, in this paper, LiNbO3 was used to prepare piezoelectric pressure sensors to study the feasibility of using LiNbO3 single crystals as a sensitive material for piezoelectric pressure sensors. In addition, chemical mechanical polishing (CMP) technology was used to prepare LiNbO3 crystals with different thicknesses to study the influence of these LiNbO3 crystals on the electric charge output of the sensors. The results showed that the sensitivity of a 300 μm sample (0.218 mV kPa-1) was about 1.23 times that of a 500 μm sample (0.160 mV kPa-1). Low-temperature polymer heterogeneous integration and oxygen plasma activation technologies were used to realize the heterogeneous integration of LiNbO3 and silicon to prepare piezoelectric pressure sensors, which could significantly improve the sensitivity of the sensor by approximately 16.06 times (2.569 mV kPa-1) that of the original sample (0.160 mV kPa-1) due to an appropriate residual stress that did not shatter LiNbO3 or silicon, thus providing a possible method for integrating piezoelectric pressure sensors and integrated circuits.

In this study, a novel approach for enhancing the rapid spreading of free liquid film on lithium niobate (LiNbO3) substrate under megahertz (MHz) surface acoustic wave (SAW) excitation is presented by treating it with surfactants. Through the design of a specific interdigital transducer structure, it was discovered that exciting the SAW at a frequency of 32.3 MHz can achieve optimal spreading performance for water droplets on the surface of surfactant-treated LiNbO3 substrate. The maximum average velocity reaches 1.76 mm/s at position P2 = 1250 μm in the water film front, and the stable film spreading speed shows a 204.9% increase compared to the existing research. Simultaneously, through the investigation of the spreading experiment phenomenon of silicone oil and de-ionized water droplets at varying frequencies, we have discovered the dynamic mechanism of "reverse phase" propagation in liquid film for the first time. This entails that the advancing edge of the wetting film demonstrates a spreading motion law that is opposite to the traditional spreading phenomena, with the spreading velocity in the central exceeding that on both sides. Our research demonstrates that this microfluidic device developed by SAWs enhances the spreading efficiency of the free films, enabling rapid expansion of the target liquid to form a high-surface area film layer. This advancement holds promise for overcoming the limitations of low sensitivity and short response time in the field of rapid pathological diagnosis in contemporary medicine. [ABSTRACT FROM AUTHOR]

In cross-country skiing, ski poles play a crucial role in technique, propulsion, and overall performance. The kinematic parameters of ski poles can provide valuable information about the skier's technique, which is of great significance for coaches and athletes seeking to improve their skiing performance. In this work, a new smart ski pole is proposed, which combines the uniaxial load cell and the inertial measurement unit (IMU), aiming to provide comprehensive data measurement functions more easily and to play an auxiliary role in training. The ski pole can collect data directly related to skiing technical actions, such as the skier's pole force, pole angle, inertia data, etc., and the system's design, based on wireless transmission, makes the system more convenient to provide comprehensive data acquisition functions, in order to achieve a more simple and efficient use experience. In this experiment, the characteristic data obtained from the ski poles during the Double Poling of three skiers were extracted and the sample t-test was conducted. The results showed that the three skiers had significant differences in pole force, pole angle, and pole time. Spearman correlation analysis was used to analyze the sports data of the people with good performance, and the results showed that the pole force and speed (r = 0.71) and pole support angle (r = 0.76) were significantly correlated. In addition, this study adopted the commonly used inertial sensor data for action recognition, combined with the load cell data as the input of the ski technical action recognition algorithm, and the recognition accuracy of five kinds of cross-country skiing technical actions (Diagonal Stride (DS), Double Poling (DP), Kick Double Poling (KDP), Two-stroke Glide (G2) and Five-stroke Glide (G5)) reached 99.5%, and the accuracy was significantly improved compared with similar recognition systems. Therefore, the equipment is expected to be a valuable training tool for coaches and athletes, helping them to better understand and improve their ski maneuver technique. [ABSTRACT FROM AUTHOR]

Ultrasound is widely applied in diverse domains, such as medical imaging, non-destructive evaluation, and acoustic communication. Piezoelectric micromachined ultrasonic transducers (PMUTs) capable of generating and receiving ultrasonic signals at the micrometer level have become a prominent technology in the field of ultrasound. It is important to enrich the models of the PMUTs to meet the varied applications. In this study, a series of PMUT devices featured with various top electrode configurations, square, circular, and doughnut, were designed to assess the influence of shape on the emission efficacy. It was demonstrated that the PMUTs with a circular top electrode were outperformed, which was calculated from the external acoustic pressure produced by the PMUTs operating in the fundamental resonant mode at a specified distance. Furthermore, the superior performance of PMUT arrays were exhibited through computational simulations for the circular top electrode geometries. Conventional microelectromechanical systems (MEMS) techniques were used to fabricate an array of PMUTs based on aluminum nitride (AlN) films. These findings make great contributions for enhancing the signal transmission sensitivity and bandwidth of PMUTs, which have significant potential in non-destructive testing and medical imaging applications. [ABSTRACT FROM AUTHOR]

With the rapid development of wearable devices, tactile sensors have received extensive attention as supplements to vision and hearing. However, it remains challenging for a single tactile sensor to generate distinguishable electrical signals when receiving mechanical stimuli in different directions. Herein, a novel flexible electromagnetic tactile sensor (FETS) prepared by combining flexible double‐layer coils and a flexible tilted magnetic column array (TMCA) is presented. Flexible double‐layer high‐density coils are fabricated using the micro‐electromechanical system (MEMS) technology. The turns of the coil (1 × 1 cm) are 100, while both the line width and spacing of turns are 40 µm. TMCA is prepared using a template and magnetized along the axis direction. When a pulling force or pressure is applied to the TMCA, the magnetic flux decreases or increases correspondingly, allowing the FETS to accurately distinguish stimuli and produce different signals (−/+ or +/−). The FETS presents a sensitivity of up to 21.7 µV kPa−1 (0.05–10 kPa), a minimal magnetic field detection limit of 10 mT, a low‐pressure detection limit of 5 g, and good repeatability (5000 cycles). Additionally, the FETS is applied in robotic tactile testing, Morse code, and noncontact magnetic field recognition. It has potential applications in the Internet of Things (IoT) and information communication. [ABSTRACT FROM AUTHOR]

The study of the properties of ferroelectric materials against irradiation has a long history. However, anti−irradiation research on the ferroelectric domain has not been carried out. In this paper, the irradiation of switched domain structure is innovatively proposed. The switched domain of 700 nm lithium niobate (LiNbO3, LN) thin film remains stable after gamma irradiation from 1 krad to 10 Mrad, which was prepared by piezoresponse force microscopy (PFM). In addition, the changing law of domain wall resistivity is explored through different sample voltages, and it is verified that the irradiated domain wall conductivity is still larger than the domain. This domain wall current (DWC) property can be applied to storage, logic, sensing, and other devices. Based on these, a ferroelectric domain irradiation resistance model is established, which explains the reason at an atomic level. The results open a possibility for exploiting ferroelectric materials as the foundation in the application of space and nuclear fields. [ABSTRACT FROM AUTHOR]

As a cutting-edge technology, animal robots based on living organisms are being extensively studied, with potential for diverse applications in the fields of neuroscience, national security, and civil rescue. However, it remains a significant challenge to reliably control the animal robots with the objective of protecting their long-term survival, and this has seriously hindered their practical implementation. To address this issue, this work explored the use of a bio-friendly neurostimulation system that includes integrated stimulation electrodes together with a remote wireless stimulation circuit to control the moving behavior of rat robots. The integrated electrodes were implanted simultaneously in four stimulation sites, including the medial forebrain bundle (MFB) and primary somatosensory cortex, barrel field (S1BF). The control system was able to provide flexibility in adjusting the following four stimulation parameters: waveform, amplitude, frequency, and duration time. The optimized parameters facilitated the successful control of the rat's locomotion, including forward movement and left and right turns. After training for a few cycles, the rat robots could be guided along a designated route to complete the given mission in a maze. Moreover, it was found that the rat robots could survive for more than 20 days with the control system implanted. These findings will ensure the sustained and reliable operation of the rat robots, laying a robust foundation for advances in animal robot regulation technology. [ABSTRACT FROM AUTHOR]

Lithium niobate (LiNbO 3 ) single crystals are a kind of ferroelectric material with a high piezoelectric coefficient and Curie temperature, which is suitable for the preparation of piezoelectric pressure sensors. However, there is little research reporting on the use of LiNbO 3 single crystals to prepare piezoelectric pressure sensors. Therefore, in this paper, LiNbO 3 was used to prepare piezoelectric pressure sensors to study the feasibility of using LiNbO 3 single crystals as a sensitive material for piezoelectric pressure sensors. In addition, chemical mechanical polishing (CMP) technology was used to prepare LiNbO 3 crystals with different thicknesses to study the influence of these LiNbO 3 crystals on the electric charge output of the sensors. The results showed that the sensitivity of a 300 μm sample (0.218 mV kPa -1 ) was about 1.23 times that of a 500 μm sample (0.160 mV kPa -1 ). Low-temperature polymer heterogeneous integration and oxygen plasma activation technologies were used to realize the heterogeneous integration of LiNbO 3 and silicon to prepare piezoelectric pressure sensors, which could significantly improve the sensitivity of the sensor by approximately 16.06 times (2.569 mV kPa -1 ) that of the original sample (0.160 mV kPa -1 ) due to an appropriate residual stress that did not shatter LiNbO 3 or silicon, thus providing a possible method for integrating piezoelectric pressure sensors and integrated circuits., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)