Search

Organic self‐assembled molecules (OSAMs) based hole‐transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol‐based OSAMs have serious drawbacks, such as poor wettability for perovskite solution spreading due to the nonpolar surface, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM [4‐(3,6‐glycol monomethyl ether‐9H‐carbazol‐9‐yl) butyl]phosphonic acid (GM‐4PACz) was synthesized as hole‐transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM‐4PACz based IPSC achieves a champion PCE of 25.52 %, a respectable open‐circuit voltage (VOC) of 1.21 V, a high stability, possessing 93.29 % and 91.75 % of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively. [ABSTRACT FROM AUTHOR]

Inverted perovskite solar cells (IPSCs) have attracted unprecedented attention due to their negligible hysteresis, long‐term operational stability, low temperature, and cost‐effective fabrication process, as well as wide applications. The power conversion efficiency (PCE) of IPSCs has skyrocketed from 3.9% in 2013 to certified 26.1% in 2023, which is over the certified 25.8% of regular counterpart, benefiting from the emergence of a great number of organic hole‐transporting materials (HTM). This review provides an overview of the recent development of organic hole‐transporting materials in the efficiency and stability of IPSCs, including organic small molecules and conjugated conductive polymers. The effective strategies for the charge‐transport layer and perovskite films of IPSCs are also discussed. Finally, the prospective for further development of IPSCs is outlined, including developing novel hole‐transporting materials and fabricating techniques to meet the requirements of commercial application. [ABSTRACT FROM AUTHOR]

A double‐fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high‐performance organic solar cells (OSCs). However, in the layer‐by‐layer processed OSCs (LbL‐OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. In this work, crystalline small molecule donors (SMDs), named TDZ‐3TR and SeDZ‐3TR, were designed and introduced into the L8‐BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ‐3TR showed higher crystallinity and lower miscibility with L8‐BO acceptor than TDZ‐3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8‐BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double‐fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL‐OSCs. [ABSTRACT FROM AUTHOR]

As simple and versatile tools, additives have been widely used to refine active layer morphology and have played a crucial role in boosting the power conversion efficiency (PCE) of organic solar cells (OSCs). Herein, three novel solvent additives named Th‐FSi, Th‐ClSi, and Th‐BrSi with the same backbone of 2,5‐bis(trimethylsilyl)thiophene are designed and synthesized by substituting different halogens of fluorine, chlorine, and bromine, respectively. Notably, Th‐ClSi exhibits the more significant dipole moment and engages in non‐covalent interactions with a small‐molecule acceptor (SMA) L8‐BO, which slight adjustments in intermolecular interaction, crystallinity, and molecular packing in the PM6:L8‐BO active layer. Consequently, the OSCs incorporating Th‐ClSi outperform their Th‐FSi and Th‐BrSi counterparts in photo‐capturing, reduced energy loss, superior exciton dissociation, and charge transfer properties, out‐coming yields in an enhanced PCE of 18.29%. Moreover, by integrating a near‐infrared absorbing SMA (BTP‐eC9) guest into the PM6:L8‐BO matrix, the absorption spectrum to span 880–930 nm, and the resultant ternary OSCs achieve a commendable PCE of 19.17%, ranking among the highest efficiencies reported to date is expanded. These findings underscore the promise of halogenated thiophene‐based solvent additives as a potent avenue for morphological fine‐tuning and consequent PCE enhancement in OSCs. [ABSTRACT FROM AUTHOR]

Background: Antral follicles consist of an oocyte cumulus complex surrounding by somatic cells, including mural granulosa cells as the inner layer and theca cells as the outsider layer. The communications between oocytes and granulosa cells have been extensively explored in in vitro studies, however, the role of oocyte-derived factor GDF9 on in vivo antral follicle development remains elusive due to lack of an appropriate animal model. Clinically, the phenotype of GDF9 variants needs to be determined. Methods: Whole-exome sequencing (WES) was performed on two unrelated infertile women characterized by an early rise of estradiol level and defect in follicle enlargement. Besides, WES data on 1,039 women undergoing ART treatment were collected. A Gdf9Q308X/S415T mouse model was generated based on the variant found in one of the patients. Results: Two probands with bi-allelic GDF9 variants (GDF9His209GlnfsTer6/S428T, GDF9Q321X/S428T) and eight GDF9S428T heterozygotes with normal ovarian response were identified. In vitro experiments confirmed that these variants caused reduction of GDF9 secretion, and/or alleviation in BMP15 binding. Gdf9Q308X/S415T mouse model was constructed, which recapitulated the phenotypes in probands with abnormal estrogen secretion and defected follicle enlargement. Further experiments in mouse model showed an earlier expression of STAR in small antral follicles and decreased proliferative capacity in large antral follicles. In addition, RNA sequencing of granulosa cells revealed the transcriptomic profiles related to defective follicle enlargement in the Gdf9Q308X/S415T group. One of the downregulated genes, P4HA2 (a collagen related gene), was found to be stimulated by GDF9 protein, which partly explained the phenotype of defective follicle enlargement. Conclusions: GDF9 bi-allelic variants contributed to the defect in antral follicle development. Oocyte itself participated in the regulation of follicle development through GDF9 paracrine effect, highlighting the essential role of oocyte-derived factors on ovarian response. [ABSTRACT FROM AUTHOR]

To simultaneously stabilize cesium lead triiodide (CsPbI3) precursor solution and passivate the defects in CsPbI3 film is greatly significant for achieving highly stable and efficient CsPbI3 perovskite solar cells (PSCs). Herein, an effective redox 4‐fluorobenzothiohydrazide (FBTH) is developed to stabilize the precursor solution and passivate iodine/lead‐related defects for high‐quality CsPbI3 film. The comprehensive research confirms that 1) a new compound FBTH‐I is obtained from an effective redox interaction between FBTH and molecular iodine (I2) in perovskite precursor solution, which can effectively impede the formation of I2 molecule and restrain I− migration in perovskite film by forming N–H···I bond; 2) FBTH‐I can also passivate Pb‐related defects via forming S···Pb interaction. Consequently, the CsPbI3 PSC based on FBTH‐treated precursor solution exhibits a fascinating power conversion efficiency (PCE) of 21.41%, which is one of the highest PCE values among the reported pure CsPbI3 PSCs so far, and an outstanding stability against the harsh conditions, such as thermal annealing and continuous light‐illumination. [ABSTRACT FROM AUTHOR]

Employing volatile solid additives have emerged as a promising method to optimize the morphology and improve the performance of organic solar cells (OSCs). However, principles governing the efficient design of solid additives remain elusive. Herein, the programmed fluorination and/or bromination on benzene core to develop efficient additives for OSCs is reported. The programmed fluorination and/or bromination endow the five halogen benzene derivatives, 1,3,5‐trifluorobenzene, hexafluorobenzene, 1,3,5‐tribromo‐2,4,6‐trifluorobenzene (TFTB), 1,3,5‐tribromobenzene, and hexabromobenzene, with different melting and boiling points, volatility, as well as interactions with the host blend. Studies indicate that the additives with extremely high and low volatility are almost powerless and even detrimental to the morphology evolution. Among them, the combination of fluorine and bromine atoms on TFTB not only enables the more appropriate m.p./b.p. and volatility, but also exerts stronger molecular interactions with the host blend, giving rise to higher ordered molecular packing and more favorable morphology. Importantly, TFTB exhibits good universality to optimize the performances of OSCs with high power conversion efficiencies (PCEs; over 18%) in a group of binary blend systems, and an impressive PCE of 19.43% in the ternary PBTz‐F:PM6:L8‐BO system. [ABSTRACT FROM AUTHOR]

Although the power conversion efficiency (PCE) of perovskite solar cells (PSCs) is 26.1%, their stability is still a roadblock for large‐scale commercialization. In the initial density‐functional theory research, it is shown that the most damaging type of defect that destroys device performance is undercoordinated Pb2+ on the surface of the perovskite thin film. An ultraviolet‐absorbent material, 2‐hydroxybenzophenone (HBP), is utilized to specifically passivate this type of defect. In theoretical studies, it is shown that it effectively binds to the undercoordinated Pb2+ via its –C═O group. It also passivates I−‐related defects by forming a hydrogen bond using its –OH group, resulting in decreased trap density and hence prolonged carrier lifetime. The HBP can absorb ultraviolet irradiation, leading to much‐reduced UV degradation; its hydrophobic benzene rings protect the perovskite from moisture permeation. As a result, the constructed device reaches a high PCE of 16.39% with superior stability. The bare device maintains 80.4% of its initial PCE after exposure to ambient air for 792 h. In comparison, the control device without HBP retains only 63.2% of its initial efficiency. Under UV irradiation (80 mW cm−2, 365 nm) for 13 h, the former retains 77.9% of its initial PCE while the control device lost 52% of its initial value. [ABSTRACT FROM AUTHOR]

The ternary copolymerization strategy has emerged as a promising strategy for developing high‐efficiency donor polymers in polymer solar cells (PSCs). Terpolymers based on the star polymer PM6 have already realized good photovoltaic performance. However, challenges such as the intricate synthesis of fluorine‐substituted benzodithiophene (F‐BDT) unit of PM6 and entropy increase induced by backbone disorder have hindered the construction of high‐performance donor terpolymers. In this work, these challenges are addressed by opting for the cost‐effective chlorinated‐substituted benzodithiophene unit (Cl‐BDT) as an alternative to F‐BDT and incorporating the large dipole moment and electron‐deficient TPD group as the third component into the high‐performance donor polymer of PM7. As expected, this approach effectively suppresses terpolymer backbone disorder while enhancing crystallinity, thereby optimizing morphology and improving charge generation and transport. Remarkably, the PM7‐TPD‐10‐based device with 10% TPD replacement achieves a champion power conversion efficiency (PCE) of 18.26%. After introducing PM7‐TPD‐10 as the third component into D18:L8‐BO blend, a dual mechanism for improving the efficiency to 19.40% is realized. This work demonstrates that the high dipole moiety as the third component to construct terpolymers is an important strategy to suppress the backbone disorder and increase the crystallinity, facilitating the optimization of morphology and device performance. [ABSTRACT FROM AUTHOR]

All-polymer solar cells have experienced rapid development in recent years by the emergence of polymerized small molecular acceptors (PSMAs). However, the strong chain entanglements of polymer donors (P D s) and polymer acceptors (P A s) decrease the miscibility of the resulting polymer mixtures, making it challenging to optimize the blend morphology. Herein, we designed three P A s, namely PBTPICm-BDD, PBTPICγ-BDD and PBTPICF-BDD, by smartly using a BDD unit as the polymerized unit to copolymerize with different Y-typed non-fullerene small molecular acceptors (NF-SMAs), thus achieving a certain degree of distortion and giving the polymer system enough internal space to reduce the entanglements of the polymer chains. Such effects increase the chances of the P D being interspersed into the acceptor material, which improve the solubility between the P D and P A . The PBTPICγ-BDD and PBTPICF-BDD displayed better miscibility with PBQx-TCl, leading to a well optimized morphology. As a result, high power conversion efficiencies (PCEs) of 17.50 % and 17.17 % were achieved for PBQx-TCl : PBTPICγ-BDD and PBQx-TCl : PBTPICF-BDD devices, respectively. With the addition of PYFT-o as the third component into PBQx-TCl : PBTPICγ-BDD blend to further extend the absorption spectral coverage and finely tune microstructures of the blend morphology, a remarkable PCE of 18.64 % was realized finally., (© 2024 Wiley-VCH GmbH.)

Various isomers have been developed to regulate the morphology and reduce defects in state-of-the-art perovskite solar cells. To insight the structure-function-effect correlations for the isomerization of thiourea derivatives on the performance of the perovskite solar cells (PSCs), we developed two thiourea derivatives [(3,5-dichlorophenyl)amino]thiourea (AT) and N-(3,5-dichlorophenyl)hydrazinecarbothioamide (HB). Supported by experimental and calculated results, it was found that AT can bind with undercoordinated Pb2+ defect through synergistic interaction between N1 and C=S group with a defect formation energy of 1.818 eV, which is much higher than that from the synergistic interaction between two -NH- groups in HB and perovskite (1.015 eV). Moreover, the stronger interaction between AT and Pb2+ regulates the crystallization process of perovskite film to obtain a high-quality perovskite film with high crystallinity, large grain size, and low defect density. Consequently, the AT-treated FACsPbI3 device engenders an efficiency of 25.71% (certified as 24.66%), which is greatly higher than control (23.74%) and HB-treated FACsPbI3 devices (25.05%). The resultant device exhibits a remarkable stability for maintaining 91.0% and 95.2% of its initial efficiency after aging 2000 h in air condition or tracking at maximum power point for 1000 h, respectively., (© 2024 Wiley‐VCH GmbH.)

Organic self-assembled molecules (OSAMs) based hole-transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol-based OSAMs have serious drawbacks, such as poor wettability for perovskite solution spreading due to the nonpolar surface, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM [4-(3,6-glycol monomethyl ether-9H-carbazol-9-yl) butyl]phosphonic acid (GM-4PACz) was synthesized as hole-transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM-4PACz based IPSC achieves a champion PCE of 25.52 %, a respectable open-circuit voltage (V OC ) of 1.21 V, a high stability, possessing 93.29 % and 91.75 % of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively., (© 2024 Wiley-VCH GmbH.)

A double-fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high-performance organic solar cells (OSCs). However, in the layer-by-layer processed OSCs (LbL-OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. In this work, crystalline small molecule donors (SMDs), named TDZ-3TR and SeDZ-3TR, were designed and introduced into the L8-BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ-3TR showed higher crystallinity and lower miscibility with L8-BO acceptor than TDZ-3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8-BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double-fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL-OSCs., (© 2024 Wiley-VCH GmbH.)

Background: Antral follicles consist of an oocyte cumulus complex surrounding by somatic cells, including mural granulosa cells as the inner layer and theca cells as the outsider layer. The communications between oocytes and granulosa cells have been extensively explored in in vitro studies, however, the role of oocyte-derived factor GDF9 on in vivo antral follicle development remains elusive due to lack of an appropriate animal model. Clinically, the phenotype of GDF9 variants needs to be determined., Methods: Whole-exome sequencing (WES) was performed on two unrelated infertile women characterized by an early rise of estradiol level and defect in follicle enlargement. Besides, WES data on 1,039 women undergoing ART treatment were collected. A Gdf9 Q308X/S415T mouse model was generated based on the variant found in one of the patients., Results: Two probands with bi-allelic GDF9 variants (GDF9 His209GlnfsTer6/S428T , GDF9 Q321X/S428T ) and eight GDF9 S428T heterozygotes with normal ovarian response were identified. In vitro experiments confirmed that these variants caused reduction of GDF9 secretion, and/or alleviation in BMP15 binding. Gdf9 Q308X/S415T mouse model was constructed, which recapitulated the phenotypes in probands with abnormal estrogen secretion and defected follicle enlargement. Further experiments in mouse model showed an earlier expression of STAR in small antral follicles and decreased proliferative capacity in large antral follicles. In addition, RNA sequencing of granulosa cells revealed the transcriptomic profiles related to defective follicle enlargement in the Gdf9 Q308X/S415T group. One of the downregulated genes, P4HA2 (a collagen related gene), was found to be stimulated by GDF9 protein, which partly explained the phenotype of defective follicle enlargement., Conclusions: GDF9 bi-allelic variants contributed to the defect in antral follicle development. Oocyte itself participated in the regulation of follicle development through GDF9 paracrine effect, highlighting the essential role of oocyte-derived factors on ovarian response., (© 2024. The Author(s).)

The success of Y6-type nonfullerene small molecule acceptors (NF-SMAs) in polymer solar cells (PSCs) can be attributed to their unique honeycomb stacking style, which leads to favorable thin-film morphologies. The intermolecular interactions related to the crystallization tendency of these NF-SMAs is closely governed by their electron accepting end groups. For example, the high performance Y6 derivative L8-BO (BTP-4F) presents three types of stacking modes in contrast to two stacking modes of Y6. Hence, it is ultimately interesting to obtain more insight on the packing properties and the preferences influenced by chemical modifications such as end group engineering. This work designs and synthesizes asymmetric and symmetric L8-BO derivatives with brominated end groups and explores the stacking preferences in various modes. The asymmetric BTP-3FBr displays an optimized crystallization tendency and thin film morphology, leading to a decent power conversion efficiency (PCE) of 18.34% in binary devices and a top PCE of 19.32% in ternary devices containing 15 wt% IDIC as the second acceptor., (© 2023 Wiley-VCH GmbH.)