Search

Ceramic particles reinforced magnesium matrix composites (CMMCs) have attracted widespread attention and investigation due to their excellent comprehensive performances. However, limited research on additive manufacturing of CMMCs has been performed. In this work, the SiC/AZ31 composites were fabricated by wire-arc directed energy deposition (WA-DED) based on the synchronous feeding strategy of powder and wire. The defects, SiC particle distribution, microstructure and mechanical properties of the prepared WA-DED SiC/AZ31 composites were studied. The results indicated that SiC particles with the content range of 0.3–1.7 wt% have been successfully added into the single-channel monolayer AZ31 matrix by adjusting the turret speed (TS) and the argon gas flow rate (AGFR) flowing through the powder feeder. The mathematical model is established to predict the introduced SiC particle content by correlating the relationship between SiC particle content and process parameters (TS and AGFR) of the powder feeder. The transformation from columnar to equiaxed grains occurs after adding SiC particles, more precipitated phases are formed after introducing more SiC particles. Compared to the AZ31 matrix, the WA-DED SiC/AZ31 composites exhibit the highest yield strength of 92.8 MPa and tensile strength of 213.3 MPa on the premise of almost no loss of elongation, and the maximum improvement efficiency of tensile strength reaches 56%, which is mainly ascribed to refinement strengthening, while thermal mismatch strengthening, Orowan strengthening and load-bearing strengthening play a booster action.

Low Pt utilization and intense carbon corrosion of cathode catalysts is a crucial issue for high‐efficiency proton exchange membrane fuel cells due to the highly demanded long‐term durability and less acquisition/application cost. Herein, structurally tunable graphitized mesoporous carbon (GMC) is obtained by direct high‐temperature pyrolysis and in situ‐controlled mesopore formation; the structure‐optimized GMC1300‐1800 exhibits a mesopore size of 7.54 nm and enhanced corrosion resistance. Functionalized GMC1300‐1800 is loaded with small‐sized Pt nanoparticles (NPs) (1.5 nm) uniformly by impregnation method to obtain Pt/GMC1300‐1800 and form an “internal platinum structure” to avoid sulfonic acid groups poisoning as well as ensure O2/proton accessibility. Hence, the electrochemically active surface area (ECSA) of Pt/GMC1300‐1800 reaches 106.1 m2 g−1Pt, while mass activity and specific activity at 0.9 V are 2.1 and 1.4 times those of commercial Pt/C, respectively. Notably, the ECSA decay is less than 17% for both 30 000 cycles’ accelerated durability tests (ADTs) of Pt attenuation and carbon attenuation. Accordingly, the optimized mesoporous structure of GMC1300‐1800 significantly decreases the coverage of sulfonic acid groups on Pt NPs, leading to the highest peak power density in the single‐cell test. Density functional theory calculations demonstrate the synergistic effect between graphitization and mesoporosity on enhancing the accessibility and durability of the catalysts.

Abstract Probiotics hold promise as a potential therapy for colorectal cancer (CRC), but encounter obstacles related to tumor specificity, drug penetration, and dosage adjustability. In this study, genetic circuits based on the E. coli Nissle 1917 (EcN) chassis were developed to sense indicators of tumor microenvironment and control the expression of therapeutic payloads. Integration of XOR gate amplify gene switch into EcN biosensors resulted in a 1.8-2.3-fold increase in signal output, as confirmed by mathematical model fitting. Co-culturing programmable EcNs with CRC cells demonstrated a significant reduction in cellular viability ranging from 30% to 50%. This approach was further validated in a mouse subcutaneous tumor model, revealing 47%-52% inhibition of tumor growth upon administration of therapeutic strains. Additionally, in a mouse tumorigenesis model induced by AOM and DSS, the use of synthetic bacterial consortium (SynCon) equipped with multiple sensing modules led to approximately 1.2-fold increased colon length and 2.4-fold decreased polyp count. Gut microbiota analysis suggested that SynCon maintained the abundance of butyrate-producing bacteria Lactobacillaceae NK4A136, whereas reducing the level of gut inflammation-related bacteria Bacteroides. Taken together, engineered EcNs confer the advantage of specific recognition of CRC, while SynCon serves to augment the synergistic effect of this approach.

This study explores the causes of coal bursts in the Xinzhou Kiln Mine, identifying key factors such as residual pillars, hard coal seams and/or roofs, stress concentration due to complex geological structures, and the stress distribution characteristics of the primary rock. A significant finding is that hydraulic cutting not only diminishes and redistributes the stress concentration region inside the coal seam but also mitigates the burst potential of the coal-rock mass, fundamentally reducing the likelihood of coal bursts. By taking Face No. 8937 in Xinzhou Kiln Mine as the test object, a coal burst prevention test was performed using hydraulic cutting. In combination with theoretical analysis and numerical simulation, the mechanism of hydraulic cutting for preventing coal burst was discussed, and reasonable cutting parameters were established. Onsite monitoring revealed that hydraulic cutting disrupts the integrity of the coal-rock mass, releases internal stress, and increases its water content, thereby weakening its burst tendency. Additionally, the deformation and fracturing of the cutting slots and the closure of boreholes shifted the stress concentration from the coal seam to deeper areas and to the two ribs. Post-cutting observations showed a significant reduction in both the frequency and impact energy of coal bursts; there was also a noticeable increase in the convergence of the roadway in the cutting area compared to non-cutting areas. Furthermore, displacement of the roof and floor increased by 78.9 % and that of the two ribs increased by 47.4 % after cutting, preventing the coal-rock mass from accumulating high stress. In conclusion, hydraulic cutting is a promising method for effectively preventing coal bursts and enhancing the safety of mining operations.

The measurement of the target azimuth angle using forward-looking radar (FLR) is widely applied in unmanned systems, such as obstacle avoidance and tracking applications. This paper proposes a semi-supervised support vector regression (SVR) method to solve the problem of small sample learning of the target angle with FLR. This method utilizes function approximation to solve the problem of estimating the target angle. First, SVR is used to construct the function mapping relationship between the echo and the target angle in beamspace. Next, by adding manifold constraints to the loss function, supervised learning is extended to semi-supervised learning, aiming to improve the small sample adaptation ability. This framework supports updating the angle estimating function with continuously increasing unlabeled samples during the FLR scanning process. The numerical simulation results show that the new technology has better performance than model-based methods and fully supervised methods, especially under limited conditions such as signal-to-noise ratio and number of training samples.

Deep cryogenic aging (DCA) is a newly developed heat treatment technique for additive-manufactured metallic materials to reduce residual stress and improve their mechanical properties. In this study, AlSi10Mg alloy samples fabricated by selective laser melting were deep-cryogenic-treated at −160 °C and subsequently aged at 160 °C. Phase and microstructural analyses were conducted using X-ray diffraction, optical microscopy, scanning electron microscopy, and transmission electron microscopy, while the mechanical properties were evaluated through microhardness and tensile testing at room temperature. The results indicated that the DCA treatment did not have an effect on the morphology of the melt pools. However, it facilitated the formation of atomic clusters and nanoscale Si and β′ phases, as well as accelerating the coarsening of grains and the ripening of the eutectic Si phase. After DCA treatment, the mass fraction of the Si phase experienced an increase from 4.4% to 7.2%. Concurrently, the volume fraction of the precipitated secondary phases elevated to 5.1%. The microhardness was enhanced to 147 HV, and the ultimate tensile strength and yield strength achieved 495 MPa and 345 MPa, respectively, with an elongation of 7.5%. In comparison to the as-built specimen, the microhardness, ultimate tensile strength, and yield strength increased by 11.4%, 3.1%, and 19.0%, respectively. The improvement in mechanical properties is primarily attributed to the Orowan strengthening mechanism induced by the secondary phases.

The microstructure characteristics of TiAl alloy prepared by laser-directed energy deposition (L-DED) are coarse columnar grains parallel to the building direction, which results in serious mechanical properties and anisotropy and limits its application. In the present study, TiB2 can be used as an effective grain refiner due to the extremely high Q value (growth inhibition factor; the larger the Q value of an alloying element, the stronger its grain refinement effect.) of B. With TiB2 addition, TiAl alloys prepared by laser-directed energy deposition with the microstructure of full equiaxed grains were obtained, and the grain size was significantly reduced by about 30% with 0.45 wt.% TiB2. This value has been further increased to 45% when adding 0.9 wt.% TiB2. Moreover, the γm phase was nearly eliminated and the width of (α2 + γ) lamellar was significantly decreased, which has positive effects on mechanical properties. Meanwhile, TiB2 precipitates uniformly distribute in the matrix, as a reinforced particle to increase the hardness and compressive strength of the alloys. The microhardness of the TiAl alloy increased with the increasing content of TiB2. The addition of TiB2 improved the room and high-temperature compressive properties of TiAl alloy while slightly increasing its ductility. These findings have important guiding significance for expanding the application of TiAl alloys.

Colorectal cancer (CRC) is a serious global health concern, and researchers have been investigating different strategies to prevent, treat, or support conventional therapies for CRC. This review article comprehensively covers CRC therapy involving wild-type bacteria, including probiotics and oncolytic bacteria as well as genetically modified bacteria. Given the close relationship between CRC and the gut microbiota, it is crucial to compile and present a comprehensive overview of bacterial therapies used in the context of colorectal cancer. It is evident that the use of native and engineered probiotics for colorectal cancer therapy necessitates research focused on enhancing the therapeutic properties of probiotic strains.. Genetically engineered probiotics might be designed to produce particular molecules or to target cancer cells more effectively and cure CRC patients.