Search

This article focuses on investigating the effect of printing direction on the mechanical properties of Cu–10Sn alloys prepared by laser powder bed fusion (LPBF) technology. Specimens with different forming angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) were fabricated using LPBF technology, and their mechanical properties were systematically tested. During the testing process, we used an Instron 5985 electronic universal material testing machine to accurately evaluate the mechanical properties of the material at a constant strain rate of 10−3/s. The experimental results showed that the mechanical properties of the specimens were the best when the test direction was perpendicular to the growth direction (i.e., the 0° direction). As the angle between the test direction and the growth direction increased, the mechanical properties of the material exhibited a trend of first decreasing, then increasing, and then decreasing again, which was consistent with the direction of the microtexture of the specimens. The root cause of this trend lies in the significant change in the stress direction borne by the columnar crystals under different load directions. Specifically, as the load direction gradually transitions from being parallel to the columnar crystals to perpendicular to them, the stress direction of the columnar crystals also shifts from the radial direction to the axial direction. Due to the differences in the number and strength of grain boundaries in different stress directions, this directly leads to changes in mechanical properties. In particular, when the specimen is loaded in the radial direction of the columnar crystals, the grain boundary density is higher, and these grain boundaries provide greater resistance during dislocation migration, thus significantly hindering tensile deformation and enabling the material to exhibit superior tensile properties. Among all the tested angles, the laser powder bed fusion specimen with a forming angle of 0° exhibited the best mechanical properties, with a tensile strength of 723 MPa, a yield strength of 386 MPa, and an elongation of 33%. In contrast, the specimen with a forming angle of 90° performed the worst in terms of tensile properties. These findings provide important insights for us to deeply understand the mechanical properties of Cu–10Sn alloys prepared by LPBF. [ABSTRACT FROM AUTHOR]

A novel high‐entropy rare‐earth disilicate (Yb0.25Lu0.25Sc0.25Tm0.25)2Si2O7 ((4RE0.25)2Si2O7) was proposed as an advanced environmental barrier coating (EBC) materials in this work. The (4RE0.25)2Si2O7 powders were synthesized using the solid‐state sintering method. Based on the X‐ray diffraction (XRD) and scanning electron microscope/energy‐dispersive spectroscopy analysis, the uniform solid solution was detected in the (4RE0.25)2Si2O7, which had a monoclinic β‐phase structure in the space group of C2/m. The lattice parameter of the structure was derived based on the Rietveld refinement analysis to the XRD results. The coefficient of thermal expansion of the bulk (4RE0.25)2Si2O7 was similar to that of the SiC‐SiC ceramic matrix composite substrate of the environmental barrier coating. In addition, this (4RE0.25)2Si2O7 bulk material had a very low thermal conductivity, which was beneficial for the application of environmental barrier coatings. The hot water‐vapor corrosive experiments were conducted in an environment of 90% air and 10% H2O at 1300°C. The results indicated a better water‐vapor corrosion performance than the commercialized Yb2Si2O7 EBC materials. The (4RE0.25)2Si2O7 material prepared in this work showed great potential to work as the environmental barrier coating. [ABSTRACT FROM AUTHOR]

In this paper, the strength development of a pure steel slag (SS) system with various concentrations of N,N,N′,N′-Tetrakis-(2-hydroxyethyl) ethylenediamine (THEED) was investigated. The hydration kinetics, pore structure and microstructure of SS pastes with and without THEED were characterized to underscore the working mechanism of THEED. Results show that THEED additions significantly increase the 3, 7 and 28 days compressive strength of hardened SS pastes. The enhancement effect increases with the dosage of THEED. At a concentration of 2000 ppm, THEED increased the compressive strength by 733%, 665%, and 545% at 3, 7 and 28 days, respectively. It is confirmed that THEED additions improve the hydration degree of SS by accelerating hydration of the aluminum phase (C3A, PDF-38-1429; C12A7, PDF-48-1882) and C2F,(PDF 38-0408) to generate Mc (PDF-41-0219) and Pa (PDF-30-0222) in the presence of CaCO3. Also, the hydration degree of silicates is increased by THEED. In this way, THEED additions refine the pore structure of hardened SS paste by increasing the pore volume with a diameter below 300 nm to achieve enhancement. The chelating effect of THEED results in promoting dissolution of SS, which provides the driving force for accelerating SS hydration. [ABSTRACT FROM AUTHOR]