Search

Underwater pulsed spark discharge has been widely used in industrial fields as a source of shock waves or acoustic waves, and numerical modeling of the discharge and pressure wave characteristics is necessary to improve the application performance. In this paper, a numerical model is proposed that couples the circuit equation, the mass and energy conservation equations, and a momentum conservation equation based on the Rankine–Hugoniot conditions. A tabulated wide range equation of state and conductivity data of water are used, and various physical processes during the plasma channel expansion are considered, including the energy flow and mass exchange between the channel and the surrounding water due to thermal radiation, evaporation, and condensation. The model self-consistently solves the circuit current and voltage, the plasma channel parameters including composition, temperature, conductivity, pressure, etc., and the pressure profile at a certain distance from the discharge channel. The calculated results show good consistency with the experimental measurements, and three sets of experimental results from other literature are tested to further verify the applicability and effectiveness of the model. [ABSTRACT FROM AUTHOR]

A rod pinch diode (RPD) is a feasible load configuration to generate a high-brightness, small-size hard x-ray radiation source. In this paper, the radiography performance of a wire-shorted low-impedance RPD on a compactly designed table-top driver (WRPD-1) is demonstrated for the first time. The driver consists of four high-power discharge branches connected in parallel, with each branch consisting of two metal-film capacitors and one multigap field-distortion switch in series. The four branches are triggered synchronously to generate a fast-rising current pulse: the inductance of the load section at the short circuit is ∼10 nH, and the short-circuit current amplitude is ∼325 kA at ±90 kV charging voltage, with a 10%–90% rise time of 110 ns. With a low-impedance RPD shorted by an 18-µm-diameter aluminum wire, a quasi-spherical x-ray focal spot with diameter <0.6 mm (width of the half-maximum grayscale) and a pulse duration of ∼25 ns (half-width of the radiation pulse) is obtained at ±70 kV charging voltage, and the imaging resolution excels 10 lp/mm under 1.56× magnification. According to the transmission–absorption x-ray spectrum estimation, the average emitted photon energy is ∼30 keV with a distinct peak in the 10–15 keV range that corresponds to the L-lines of tungsten, and the total energy of photons >10 keV reaches ∼1.16 J. The present results show that the device can serve well for the flash radiography diagnosis and potentially as an efficient light source for dynamic x-ray diffraction. [ABSTRACT FROM AUTHOR]

Initial wire resistance is an important parameter in an underwater electrical wire explosion because it directly affects the discharge characteristics of the circuit and indirectly affects the explosion and shock-wave generation. This paper presents a study on how the initial resistance affects electrical and shock-wave characteristics of underwater electrical explosions of aluminum wires with an initial energy storage of ∼53.5 kJ under the optimal mode. Load voltage, circuit current, and shock-wave pressure were recorded and analyzed. The experimental results show that the average of the discharge channel resistance and the total energy deposition all increase with the initial resistance. In addition, there is no simple functional relationship between the energy deposition during the phase transition process and the initial resistance, while the energy deposition during the plasma growth process increases with the initial resistance. As for shock waves at ∼33 cm, it is observed that when the initial resistance increases from 674.82 to 1581.60 μ Ω , the peak pressure, energy density, and impulse increase from 12.65 MPa, 2.67 kJ/m2, and 964.51 Pa s to 42.37 MPa, 18.21 kJ/m2, and 1940.42 Pa s, respectively. In other words, for the optimal mode, an underwater electrical explosion with thinner and longer wire is more conducive to generating strong shock waves in the far-field regime. These results should help select loads for underwater electrical wire explosions in engineering applications. [ABSTRACT FROM AUTHOR]

Measurement of plasma parameters during the ablation phase in the Z-pinch is crucial for investigating the dynamic behaviors. In this study, optical Thomson scattering was employed to measure the temperature and velocity of the ablation plasma in a double-wire Z-pinch. The scattering spectra profiles were fitted using a model that considered the velocity distribution. The experimental results revealed the energy evolution of ablation plasma, the establishment of the global magnetic field and the development of axial non-uniformities. The precursor plasma was found to play a key role in strengthening the global magnetic field. A resistive layer near the wire core with a size of 1.5 mm was observed in the ablation plasma after the precursor plasma column formed. The plasma underwent rapid heating in this layer, the electron temperature rises from 17 eV to 22 eV. Upon leaving this layer, electron the temperature is stable at around 22 eV. The radial distribution of the ablation rate increases and decreases, indicating the axial motion of the ablation plasma, which could be caused by the tilt motion of the stream and the secondary modulation of the natural wavelength. [ABSTRACT FROM AUTHOR]

In this paper, Fe10Co25Ni34Cu23Al8 high-entropy-alloy nanoparticles have been synthesized by the in situ instantaneous electrical wire explosion method. Based on the thermodynamic parameters of the face-centered cubic phase of high-entropy-alloy, the parameters of the five kinds of wires were calculated and controlled, and the stable face-centered cubic structure with good crystallinity was synthesized in one step. The influence of the energy deposition during the electrical explosion on the nanoparticles and their electromagnetic absorption performance was explored. The results show that the face-centered cubic structure high-entropy-alloy with high crystallinity has better electromagnetic wave absorption performance when the energy deposition of the wires is increased. The minimum reflection loss can reach −39.37 dB at 15.34 GHz when the thickness is 1.9 mm and the effective absorption bandwidth is 6.63 GHz. It can provide a strategy for the microstructure and morphology design of high-entropy-alloy nanoparticles in electromagnetic wave absorption and magnetism in the electronics industry. [ABSTRACT FROM AUTHOR]