Search

• During non-glint season, the main source of light reflected by GEO satellites is MLI. • GEO satellite reflectance spectra remain stable at varying phase angles. • Normalized reflectance spectra remain stable despite solar declination changes. Geostationary orbit (GEO) satellites have extensive application in fields like communications and navigation due to their stationary properties. Using additional methods to identify and characterise GEO satellites is crucial for enhancing cataloguing capabilities and verifying their operation status. Reflectance spectroscopy is a promising technique for characterising satellites, but a deeper understanding of the primary factors influencing satellite reflectance spectra is required. So we carried out slitless spectroscopic observations on six GEO satellites using the 80 cm high-precision telescope of the Purple Mountain Observatory located in Yaoan, Yunnan. Reflectance spectra and by-product light curves were then obtained after necessary spectral extraction and correction procedures. Our experiment and observation lasted over ten months, and this paper utilizes a subset of data with high Signal-to-Noise Ratio(SNR). Based on the reflectance spectral data obtained, we discovered that: The dominant factor impacting the reflectance spectra is the Multi-layer insulation(MLI) on the surface of three-axis stabilized GEO satellites. Reflectance spectral trends of GEO satellites do not change significantly over the course of a night with changes in the sun-satellite-observatory phase angle. The normalised reflectance spectral trends remain unchanged despite variations in the solar declination. The aforementioned findings establish a strong basis for utilising reflectance spectra to recognise and classify non-cooperative GEO satellites. [ABSTRACT FROM AUTHOR]

Hyperspectral imaging has shown great promise for diagnostic applications, particularly in cancer surgery. However, non-bulk tissue-related spectral variations complicate the data analysis. Common techniques, such as standard normal variate normalization, often lead to a loss of amplitude and scattering information. This study investigates a novel approach to address these spectral variations in hyperspectral images of optical phantoms and excised human breast tissue. Our method separates surface and volume reflectance, hypothesizing that spectral variability arises from significant variations in surface reflectance across pixels. An illumination setup was developed to measure samples with a hyperspectral camera from different axial positions but with identical zenith angles. This configuration, combined with a novel data analysis approach, allows for the estimation and separation of surface reflectance for each direction and volume reflectance across all directions. Validated with optical phantoms, our method achieved an 83% reduction in spectral variability. Its functionality was further demonstrated in excised human breast tissue. Our method effectively addresses variations caused by surface reflectance or glare while conserving surface reflectance information, which may enhance sample analysis and evaluation. It benefits samples with unknown refractive index spectra and can be easily adapted and applied across a wide range of fields where hyperspectral imaging is used. [ABSTRACT FROM AUTHOR]

This article provides an updated review of advances in the field of mirror-based laser beam deflectors, including laser scanners. We propose a taxonomy of these techniques based mainly on the principle of operation, and we direct the reader to the literature related to the individual subgroups of deflectors and to some of the most representative examples. This review is limited to the continuous or quasi-continuous mode of operation. The following techniques for steering mirror deflection are distinguished: electromagnetic, piezo, electrothermal, electrostatic and pressure actuators. Electromagnetic voice coils and piezo deflectors form one subgroup of fast steering mirror techniques. The main technical parameters and the useable properties of each group of techniques are specified. This review forms the first part of a general overview of laser beam deflectors, which will continue with a review of refractive and diffraction deflectors. [Display omitted] • The first part of a general overview of laser beam deflectors, which will next cover refractive and diffraction deflectors. • Actualised overview of advances in specular reflection by light laser beam deflectors, including laser scanners. • New approach and taxonomy of the presented techniques. • References to the earlier reviews of subgroups. • Main steering mirror techniques distinguished: electromagnetic, piezo, electrothermal, electrostatic and pressure actuators. [ABSTRACT FROM AUTHOR]

Gloss is associated significantly with material appearance, and observers often focus on gloss unevenness. Gloss unevenness is the intensity distribution of reflected light observed within a highlight area, that is, the variability. However, it cannot be analyzed easily because it exists only within the highlight area and varies in appearance across the reflection angles. In recent years, gloss has been analyzed in terms of the intensity of specular reflection and its angular spread, or the bidirectional reflectance distribution function (BRDF). In this study, we develop an apparatus to measure gloss unevenness that can alter the angle with an angular resolution of 0.02°. Additionally, we analyze the gloss unevenness and BRDF in terms of specular reflection. Using a high angular resolution, we measure and analyze high-gloss materials, such as mirrors and plastics, and glossy materials, such as photo-like inkjet paper and coated paper. Our results show that the magnitude of gloss unevenness is the largest at angles marginally off the center of the specular reflection angle. We discuss an approach for physically defining gloss unevenness based on the BRDF. [ABSTRACT FROM AUTHOR]

Purpose: Specular reflections in endoscopic images not only disturb visual perception but also hamper computer vision algorithm performance. However, the intricate nature and variability of these reflections, coupled with a lack of relevant datasets, pose ongoing challenges for removal. Methods: We present EndoSRR, a robust method for eliminating specular reflections in endoscopic images. EndoSRR comprises two stages: reflection detection and reflection region inpainting. In the reflection detection stage, we adapt and fine-tune the segment anything model (SAM) using a weakly labeled dataset, achieving an accurate reflection mask. For reflective region inpainting, we employ LaMa, a fast Fourier convolution-based model trained on a 4.5M-image dataset, enabling effective inpainting of arbitrarily shaped reflection regions. Lastly, we introduce an iterative optimization strategy for dual pre-trained models to refine the results of specular reflection removal, named DPMIO. Results: Utilizing the SCARED-2019 dataset, our approach surpasses state-of-the-art methods in both qualitative and quantitative evaluations. Qualitatively, our method excels in accurately detecting reflective regions, yielding more natural and realistic inpainting results. Quantitatively, our method demonstrates superior performance in both segmentation evaluation metrics (IoU, E-measure, etc.) and image inpainting evaluation metrics (PSNR, SSIM, etc.). Conclusion: The experimental results underscore the significance of proficient endoscopic specular reflection removal for enhancing visual perception and downstream tasks. The methodology and results presented in this study are poised to catalyze advancements in specular reflection removal, thereby augmenting the accuracy and safety of minimally invasive surgery. [ABSTRACT FROM AUTHOR]

When modeling heat transfer in nanoribbons, an unusually sharp dependence of the heat flux, and, consequently, the thermal conductivity coefficient, on the degree of specularity of phonon reflection from the lateral boundaries was found. From numerical calculations, it followed that the addition of minimally diffuse scattering should lead to an abrupt increase in the thermal resistance of the conductor. Given the importance of selecting optimal thermal parameters in nanotechnology, this short paper provides an analysis of the found dependencies, discusses the physical reasons for this anomalous behavior, and draws conclusions about the importance of achieving the quality of the nanoconductor interface to create thermal contacts with a given or optimal thermal conductivity. [ABSTRACT FROM AUTHOR]

Active illumination light becomes strongly reflective interference light after specular reflection. It causes saturation in some areas of the image during target detection, resulting in the inability to recognize detailed target feature information. This greatly limits the application of active illumination detection. Based on the Mueller matrix analysis of the difference in polarization characteristics between the background specular reflected light and the target reflected light, we propose a reflection suppression method based on orthogonal polarization imaging. The method employs a polarization modulation strategy in a bidirectional manner between the light source and the detector. First, the polarization information difference is amplified by active polarized illumination between the background specular reflected light and the target reflected light. Then, the target recovery is achieved by suppressing the background specular reflected light through the polarized orthogonal imaging method. Meanwhile, this method can also be used for moving target detection. The experimental results show that the reflection suppression method of orthogonal polarization imaging can effectively suppress the interference of specular reflection on the target image. Additionally, it can reduce the problems of missed and false detection that occurs in moving target detection and improve the active illumination detection effect. [ABSTRACT FROM AUTHOR]

In this article, the phenomena of beam deviation in reflectarray is discussed. The radiation pattern of the unit cell, which plays a vital role in shaping the beam of the reflectarray, is analyzed by considering undesired specular and scattered reflections. These unwanted reflections adversely affect the pattern of the single unit cell, thereby reducing the overall performance of the reflectarray. To conduct our investigations, three cases of reflectarray—i.e., (i) a center-fed with broadside beam (Case-I), (ii) a center-fed with the beam at 30° (Case-II), and (iii) off-center-fed with the beam at 30° reciprocal to feed position with reference to the broadside direction (Case-III)—are simulated. Different degrees of beam deviation are analyzed in each reflectarray by assessing the radiation pattern of a single element. The simulation results shows that maximum of 0°, 3.4°, and 0.54° beam squint across the bandwidth found in Case-I, Case-II, and Case-III, respectively; this leads to aperture efficiencies of 31.2%, 11.9%, and 31.2%, respectively. The significance of specular reflections is further confirmed by half (left half and right half) aperture analysis of Case-II. This involves simulating the half-plane aperture illuminated by horn antenna, resulting in a distinct beam angle at the same frequency. However, deviations of −4.71 to +4.1 for the left half aperture and −1.82 to +1.1 for the right half aperture are noticed. Although the analysis specifically focuses on the three cases of the reflectarray, the proposed methodology is applicable to any type of reflectarray. The study presented in this work provides an important insight into the practical aspects of reflectarray operation, particularly in terms of quantifying undesirable effects that are normally overlooked in the design of this class of arrays. To achieve a good performance, a new design of the dielectric loaded horn feed is proposed. This design approach is both simple and applicable to any reflectarray, with the added benefit of maintaining a low profile for the RA. Moreover, this work holds significant potential for remote sensing satellite systems as beam deviation can adversely impact data collection accuracy and compromise observation precision, resulting in distorted images, reduced data quality, and overall hindrance to the system's performance in capturing reliable information. [ABSTRACT FROM AUTHOR]

Optical 3D detection technology has a wide range of applications in industrial detection, agricultural production, and so on. Its advantages are non-contact, efficiency, and high precision. However, the specular reflection problem affects model coverage and measurement accuracy. An optimization algorithm for calculating the number and pose of sensors has been proposed to address this issue. First, the specular reflection problem is viewed as a multi-sensor position search problem. Then, an optimization algorithm is used to find the optimal number and bit positions of sensors to avoid specular reflection. The experiment shows that the optimization results of this algorithm can cover the area to be measured with the least number of sensor combinations while avoiding the influence of specular reflection. [ABSTRACT FROM AUTHOR]

Hyperspectral imaging has shown great promise for diagnostic applications, particularly in cancer surgery. However, non-bulk tissue-related spectral variations complicate the data analysis. Common techniques, such as standard normal variate normalization, often lead to a loss of amplitude and scattering information. This study investigates a novel approach to address these spectral variations in hyperspectral images of optical phantoms and excised human breast tissue. Our method separates surface and volume reflectance, hypothesizing that spectral variability arises from significant variations in surface reflectance across pixels. An illumination setup was developed to measure samples with a hyperspectral camera from different axial positions but with identical zenith angles. This configuration, combined with a novel data analysis approach, allows for the estimation and separation of surface reflectance for each direction and volume reflectance across all directions. Validated with optical phantoms, our method achieved an 83% reduction in spectral variability. Its functionality was further demonstrated in excised human breast tissue. Our method effectively addresses variations caused by surface reflectance or glare while conserving surface reflectance information, which may enhance sample analysis and evaluation. It benefits samples with unknown refractive index spectra and can be easily adapted and applied across a wide range of fields where hyperspectral imaging is used.

Gloss is associated significantly with material appearance, and observers often focus on gloss unevenness. Gloss unevenness is the intensity distribution of reflected light observed within a highlight area, that is, the variability. However, it cannot be analyzed easily because it exists only within the highlight area and varies in appearance across the reflection angles. In recent years, gloss has been analyzed in terms of the intensity of specular reflection and its angular spread, or the bidirectional reflectance distribution function (BRDF). In this study, we develop an apparatus to measure gloss unevenness that can alter the angle with an angular resolution of 0.02°. Additionally, we analyze the gloss unevenness and BRDF in terms of specular reflection. Using a high angular resolution, we measure and analyze high-gloss materials, such as mirrors and plastics, and glossy materials, such as photo-like inkjet paper and coated paper. Our results show that the magnitude of gloss unevenness is the largest at angles marginally off the center of the specular reflection angle. We discuss an approach for physically defining gloss unevenness based on the BRDF.

Active illumination light becomes strongly reflective interference light after specular reflection. It causes saturation in some areas of the image during target detection, resulting in the inability to recognize detailed target feature information. This greatly limits the application of active illumination detection. Based on the Mueller matrix analysis of the difference in polarization characteristics between the background specular reflected light and the target reflected light, we propose a reflection suppression method based on orthogonal polarization imaging. The method employs a polarization modulation strategy in a bidirectional manner between the light source and the detector. First, the polarization information difference is amplified by active polarized illumination between the background specular reflected light and the target reflected light. Then, the target recovery is achieved by suppressing the background specular reflected light through the polarized orthogonal imaging method. Meanwhile, this method can also be used for moving target detection. The experimental results show that the reflection suppression method of orthogonal polarization imaging can effectively suppress the interference of specular reflection on the target image. Additionally, it can reduce the problems of missed and false detection that occurs in moving target detection and improve the active illumination detection effect.

Optical 3D detection technology has a wide range of applications in industrial detection, agricultural production, and so on. Its advantages are non-contact, efficiency, and high precision. However, the specular reflection problem affects model coverage and measurement accuracy. An optimization algorithm for calculating the number and pose of sensors has been proposed to address this issue. First, the specular reflection problem is viewed as a multi-sensor position search problem. Then, an optimization algorithm is used to find the optimal number and bit positions of sensors to avoid specular reflection. The experiment shows that the optimization results of this algorithm can cover the area to be measured with the least number of sensor combinations while avoiding the influence of specular reflection.

In this article, the phenomena of beam deviation in reflectarray is discussed. The radiation pattern of the unit cell, which plays a vital role in shaping the beam of the reflectarray, is analyzed by considering undesired specular and scattered reflections. These unwanted reflections adversely affect the pattern of the single unit cell, thereby reducing the overall performance of the reflectarray. To conduct our investigations, three cases of reflectarray—i.e., (i) a center-fed with broadside beam (Case-I), (ii) a center-fed with the beam at 30° (Case-II), and (iii) off-center-fed with the beam at 30° reciprocal to feed position with reference to the broadside direction (Case-III)—are simulated. Different degrees of beam deviation are analyzed in each reflectarray by assessing the radiation pattern of a single element. The simulation results shows that maximum of 0°, 3.4°, and 0.54° beam squint across the bandwidth found in Case-I, Case-II, and Case-III, respectively; this leads to aperture efficiencies of 31.2%, 11.9%, and 31.2%, respectively. The significance of specular reflections is further confirmed by half (left half and right half) aperture analysis of Case-II. This involves simulating the half-plane aperture illuminated by horn antenna, resulting in a distinct beam angle at the same frequency. However, deviations of −4.71 to +4.1 for the left half aperture and −1.82 to +1.1 for the right half aperture are noticed. Although the analysis specifically focuses on the three cases of the reflectarray, the proposed methodology is applicable to any type of reflectarray. The study presented in this work provides an important insight into the practical aspects of reflectarray operation, particularly in terms of quantifying undesirable effects that are normally overlooked in the design of this class of arrays. To achieve a good performance, a new design of the dielectric loaded horn feed is proposed. This design approach is both simple and applicable to any reflectarray, with the added benefit of maintaining a low profile for the RA. Moreover, this work holds significant potential for remote sensing satellite systems as beam deviation can adversely impact data collection accuracy and compromise observation precision, resulting in distorted images, reduced data quality, and overall hindrance to the system’s performance in capturing reliable information.

• We investigated the impact of perceived glossiness on pupillary response. • Observers rated perceived glossiness of stimuli with controlled image features. • Higher gloss ratings induced greater pupil constriction than lower ratings. Recent studies have revealed that pupillary response changes depend on perceptual factors such as subjective brightness caused by optical illusions and luminance. However, the manner in which the perceptual factor that is derived from the glossiness perception of object surfaces affects the pupillary response remains unclear. We investigated the relationship between the glossiness perception and pupillary response through a glossiness rating experiment that included recording the pupil diameter. We prepared general object images (original) and randomized images (shuffled) that comprised the same images with randomized small square regions as stimuli. The image features were controlled by matching the luminance histogram. The observers were asked to rate the perceived glossiness of the stimuli presented for 3,000 ms and the changes in their pupil diameters were recorded. Images with higher glossiness ratings constricted the pupil size more than those with lower glossiness ratings at the peak constriction of the pupillary responses during the stimulus duration. The linear mixed-effects model demonstrated that the glossiness rating, image category (original/shuffled), variance of the luminance histogram, and stimulus area were most effective in predicting the pupillary responses. These results suggest that the illusory brightness obtained by the image regions of high-glossiness objects, such as specular highlights, induce pupil constriction. [ABSTRACT FROM AUTHOR]

Pearlescent materials are of technological importance in a diverse array of industries from cosmetics to premium paints; however, chiral pearlescent materials remain unexplored. Here, chiral pearlescent films with on-demand iridescence and metallic appearance are simply organized by leveraging vertical pressure to direct the self-assembly of cellulose nanocrystals. The films are formed with a bilayer planar anchored left-handed chiral nematic architecture, in which the bottom layer is featured with a vertical gradient pitch, and the top layer is featured with a uniform pitch. Simultaneous reflection of the rainbow colors and an on-demand color of left-handed polarized light with angle-dependent wavelength and polarization state accounts for the unique optical phenomenon based on experimental observation and theoretical analysis. Such chiroptical property can be readily tuned with architectural design, enabling reproducible optical appearance with high fidelity. Bringing the pearlescence, iridescence, and specular reflection together endows cellulose nanocrystal films with rich and tunable chiroptical properties that can be used for anti-counterfeiting applications. The current work marks the beginning of chiral pearlescent materials from renewable resources, while the pressure-directed self-assembly provides a step toward scalable production., (© 2023 Wiley‐VCH GmbH.)

Purpose: Specular reflections (SRs) are highlight artifacts commonly found in endoscopy videos that can severely disrupt a surgeon's observation and judgment. Despite numerous attempts to restore SR, existing methods are inefficient and time consuming and can lead to false clinical interpretations. Therefore, we propose the first complete deep-learning solution, SpecReFlow, to detect and restore SR regions from endoscopy video with spatial and temporal coherence., Approach: SpecReFlow consists of three stages: (1) an image preprocessing stage to enhance contrast, (2) a detection stage to indicate where the SR region is present, and (3) a restoration stage in which we replace SR pixels with an accurate underlying tissue structure. Our restoration approach uses optical flow to seamlessly propagate color and structure from other frames of the endoscopy video., Results: Comprehensive quantitative and qualitative tests for each stage reveal that our SpecReFlow solution performs better than previous detection and restoration methods. Our detection stage achieves a Dice score of 82.8% and a sensitivity of 94.6%, and our restoration stage successfully incorporates temporal information with spatial information for more accurate restorations than existing techniques., Conclusions: SpecReFlow is a first-of-its-kind solution that combines temporal and spatial information for effective detection and restoration of SR regions, surpassing previous methods relying on single-frame spatial information. Future work will look to optimizing SpecReFlow for real-time applications. SpecReFlow is a software-only solution for restoring image content lost due to SR, making it readily deployable in existing clinical settings to improve endoscopy video quality for accurate diagnosis and treatment., (© 2024 The Authors.)