Search

Developing reversible lithium metal anodes with high rate capability is one of the central aims of current battery research. Lithium metal anodes are not only required for the development of innovative cell concepts such as lithium-air or lithium-sulfur batteries, they can also increase the energy density of batteries with intercalation-type cathodes. The use of solid electrolyte separators is especially promising to develop well-performing lithium metal anodes, because they can act as a mechanical barrier to avoid unwanted dendritic growth of lithium through the cell. However, inhomogeneous electrodeposition and contact loss often hinder the application of a lithium metal anode in solid-state batteries. In this review, we assess the physicochemical concepts that describe the fundamental mechanisms governing lithium metal anode performance in combination with inorganic solid electrolytes. In particular, our discussion of kinetic rate limitations and morphological stability intends to stimulate further progress in the field of lithium metal anodes. [ABSTRACT FROM AUTHOR]

Solid-state electrolytes (SSEs) have been widely considered as enabling materials for the practical application of lithium metal anodes. However, many problems inhibit the widespread application of solid state batteries, including the growth of lithium dendrites, high interfacial resistance, and the inability to operate at high current density. In this study, we report a three-dimensional (3D) mixed electron/ion conducting framework (3D-MCF) based on a porous-dense-porous trilayer garnet electrolyte structure created via tape casting to facilitate the use of a 3D solid state lithium metal anode. The 3D-MCF was achieved by a conformal coating of carbon nanotubes (CNTs) on the porous garnet structure, creating a composite mixed electron/ion conductor that acts as a 3D host for the lithium metal. The lithium metal was introduced into the 3D-MCF via slow electrochemical deposition, forming a 3D lithium metal anode. The slow lithiation leads to improved contact between the lithium metal anode and garnet electrolyte, resulting in a low resistance of 25 O cm2. Additionally, due to the continuous CNT coating and its seamless contact with the garnet we observed highly uniform lithium deposition behavior in the porous garnet structure. With the same local current density, the high surface area of the porous garnet framework leads to a higher overall areal current density for stable lithium deposition. An elevated current density of 1 mA/cm2 based on the geometric area of the cell was demonstrated for continuous lithium cycling in symmetric lithium cells. For battery operation of the trilayer structure, the lithium can be cycled between the 3D-MCF on one side and the cathode infused into the porous structure on the opposite side. The 3D-MCF created by the porous garnet structure and conformal CNT coating provides a promising direction toward new designs in solid-state lithium metal batteries. [ABSTRACT FROM AUTHOR]

Magnesium substituted P2-structure Na0.67Ni0.3Mn0.7O2 materials have been prepared by a facile solid-state method and investigated as cathodes in sodium-ion batteries. The Mg-doped materials described here were characterized by X-ray diffraction (XRD), 23Na solid-state nuclear magnetic resonance (SS-NMR), and scanning electron microscopy (SEM). The electrochemical performance of the samples was tested in half cells vs Na metal at room temperature. The Mg-doped materials operate at a high average voltage of ca. 3.3 V vs Na/Na+ delivering specific capacities of -120 mAh g-1, which remain stable up to 50 cycles. Mg doping suppresses the well-known P2-O2 phase transition observed in the undoped composition by stabilizing the reversible OP4 phase during charging (during Na removal). GITT measurements showed that the Na-ion mobility is improved by 2 orders of magnitude with respect to the parent P2-Na0.67Ni0.3Mn0.7O2 material. The fast Na-ion mobility may be the cause of the enhanced rate performance. [ABSTRACT FROM AUTHOR]

All solid-state batteries are of key importance in the development of next-generation energy storage devices with high energy density. Herein, we report the fabrication and operation of bulk-type 5 V-class all solid-state batteries consisting of LiNi0.5Mn1.5O4 cathode, Li10GeP2S12 solid-electrolyte, and Li metal anode. The 1st discharge capacity is about 80 mAh g-1 with an average voltage of 4.3 V. The discharge capacity gradually decreases during the subsequent cycles. X-ray diffraction and electrochemical impedance spectroscopy measurements reveal that the capacity fading results from the growth of a resistive interfacial layer on the cathode composite. The development of suitable conductive additive and sulfide solid electrolyte materials is essential for the development of high-voltage all solid-state batteries. [ABSTRACT FROM AUTHOR]