Search

Transition metal oxide nanostructures are drawing much attention as promising electrodes for advanced rechargeable batteries. However, due to the intrinsic low electronic conductivity and substantial volume change during cycling, the electrodes usually show low rate capability and poor cycling life. Herein, we report a route combining surface/interface engineering and defect chemistry to tune the lithium storage properties in nanoscale cubic Co3O4 crystallites. The Co3O4 crystallites were annealed in an inert atmosphere by carefully controlling the temperature, which induces the conformal formation of CoO layers with a tunable thickness on the surface of initial cubes. Microstructural characterizations and electrochemical measurements indicate that the optimized sample possesses a CoO thickness of ∼1.1 nm and shows a reversible lithium storage capacity of 1069.4 mAh·g–1 after 100 cycles of a current density of 0.1 A·g–1. A capacity of 807.9 mAh·g–1 can be obtained at a rate of 5 A·g–1. The improved lithium storage performance is attributed to the unique CoO–Co3O4 interface structure and defect chemistry, which induces a strong electric field at the sharp Co3O4–CoO interface according to density functional theory calculations. The optimized sample also shows it improved sodium storage properties. This work thus provides an effective strategy for the design and synthesis of advanced electrode materials for energy applications. [ABSTRACT FROM AUTHOR]

Lanthanide-doped upconversion nanoparticles (UCNPs) have unique photoluminescent properties that are useful in many biomedical applications. Modification of UCNPs with a polymer layer can confer additional functionality such as biocompatibility, stability in vivo, or drug delivery capability. It is also important that the modification process can be controlled precisely and without having adverse effects on the UCNPs luminescence properties. Herein, a polymer shell was grafted directly from the surface of UCNPs (grafting from) via visible light (λmax = 635 nm, 0.7 mW/cm2) regulated photoenergy/electron transfer-reversible addition fragmentation chain transfer polymerization (PET-RAFT). The polymerization kinetics, grafting density, and thickness of the surface-tethered polymer chains can be tuned precisely by adjusting the monomer and RAFT agent ratio or the light exposure time. This approach also permits temporal control of the polymerization process. That is, the polymerization process can be initiated, halted, or terminated by switching the light source on and off. By limiting the non-radiative decay caused by surface defects, as well as from vibrational deactivation from solvents, the polymer shell enhanced the upconversion luminescence of the silica-coated UCNPs. This investigation paves the way for the development of UCNPs with controlled properties for various application requirements. [ABSTRACT FROM AUTHOR]

A series of novel metal-oxide-supported CeO2 catalysts were prepared via the wet impregnation method, and their NH3-SCR activities were investigated. The Ce/TiO2-SiO2 catalyst with a Ti/Si mass ratio of 3/1 exhibited superior NH3-SCR activity and high N2 selectivity in the temperature range of 250-450 °C. The characterization results revealed that the activity enhancement was correlated with the properties of the support material. Cerium was highly dispersed on the TiO2-SiO2 binary metal oxide support, and the interaction of Ti and Si resulted in greater conversion of Ce4+ to Ce3+ on the surface of the catalyst compared to that on the single metal oxide supports. As a result of in the increased number of acid sites on Ce/TiO2-SiO2 that resulted from the addition of SiO2, the NH3 adsorption capacity was significantly improved. All of these factors played significant roles in the high SCR activity. More importantly, Ce/TiO2-SiO2 exhibited strong resistance to SO2 and H2O poisoning. After the addition of SiO2, the number of Lewis-acid sites was not decreased, but the number of Brønsted-acid sites on the TiO2-SiO2 carrier was increased. The introduction of SiO2 further weakened the alkalinity over the surface of the Ce/TiO2-SiO2 catalyst, which resulted in sulfate not easily accumulating on the surface of the Ce/TiO2-SiO2 catalyst in comparison with Ce/TiO2. [ABSTRACT FROM AUTHOR]

Mesoporous metals with high surface area hold promise for a variety of catalytic applications, especially for the reduction of CO 2 to value-added products. This study has used a novel mesoporous rhodium (Rh) nanoparticles, which were recently developed via a simple wet chemical reduction approach ( Nat. Commun. 2017, 8, 15581) as catalyst for CO 2 methanation. Highly efficient performance and selectivity for methane formation are achieved due to their controllable crystallinity, high porosity, high surface energy, and large number of atomic steps distributions. The mesoporous Rh nanoparticles, possessing the largest surface area (69 m 2 g -1 ), exhibit a substantially higher reaction rate (5.28 × 10 -5 mol CO 2 g Rh -1 s -1 ) than the nonporous Rh nanoparticles (1.28 × 10 -5 mol CO 2 g Rh -1 s -1 ). Our results indicate the extensive use of mesoporous metals in heterogeneous catalysis processes.

Unique CO 2 methanation catalysts comprising bimetallic Ni-Rh nanoalloy/3DOM LaAlO 3 have been successfully prepared via a poly(methyl methacrylate) microsphere colloidal crystal-templating route, followed by the in situ growth of Ni nanoparticles (NPs). Here, we show that unlike traditional Ni particles deposited on a perovskite support, the exsolution of Ni occurs on both the external and internal surface of the porous perovskite substrate, leading to a strong metal-support interaction. Owing to the exsolution of Ni and the formation of Ni-Rh nanoalloys, a 52% enhancement in the methanation turnover frequency was obtained over the Ni-Rh/3DOM LaAlO 3 [13.9 mol/(mol h)] compared to Rh/3DOM LaNi 0.08 Al 0.92 O 3 [9.16 mol/(mol h)] before reduction treatment. The results show that the low-temperature reducibility, rich surface adsorbed oxygen species, and basic sites of the catalyst greatly improve its activity toward CO 2 methanation. The hierarchically porous structure of the perovskite support provides a high dispersion of bimetallic Ni-Rh NPs.

We report a scalable method to obtain a new material where large graphene sheets form webs linking carbon fibers. Film-fiber hybrid nonwoven mats are formed during fiber processing and converted to carbon structures after a simple thermal treatment. This contrasts with multistep methods that attempt to mix previously prepared graphene and fibers, or require complicated and costly processes for deposition of graphene over carbon fibers. The developed graphene-fiber hybrid structures have seamless connections between graphene and fibers, and in fact the graphene "veils" extend directly from one fiber into another forming a continuous surface. The graphene-fiber hybrid structures are produced in situ from aqueous poly(vinyl alcohol) solutions. The solutions were subjected to centrifugal spinning to produce fine nanofiber mats. The addition of salt to the polymer solution stimulated a capillarity effect that promoted the formation of thin veils, which become graphene sheets upon dehydration by sulfuric acid vapor followed by carbonization (at relatively low temperatures, below 800 °C). These veils extend over several micrometers within the pores of the fiber network, and consist of crystalline graphene layers that cross-link the fibers to form a highly interconnected hybrid network. The surface area and pore diameter of the hybrid structures were measured to be 521 m 2 g -1 and 10 nm, respectively. The resulting structure shows high electrical conductivity, 550 S/m, and promising shielding of electromagnetic interference, making it an attractive system for a broad range of electronic applications.

To overcome deactivation of Pd-based catalysts at high temperatures, we herein design a novel pathway by introducing a certain amount of CoO to the supported Au-Pd alloy nanoparticles (NPs) to generate high-performance Au-Pd-xCoO/three-dimensionally ordered macroporous (3DOM) Co 3 O 4 (x is the Co/Pd molar ratio) catalysts. The doping of CoO induced the formation of PdO-CoO active sites, which was beneficial for the improvement in adsorption and activation of CH 4 and catalytic performance. The Au-Pd-0.40CoO/3DOM Co 3 O 4 sample performed the best (T 90% = 341 °C at a space velocity of 20 000 mL g -1 h -1 ). Deactivation of the 3DOM Co 3 O 4 -supported Au-Pd, Pd-CoO, and Au-Pd-xCoO nanocatalysts resulting from water vapor addition was due to the formation and accumulation of hydroxyl on the catalyst surface, whereas deactivation of the Pd-CoO/3DOM Co 3 O 4 catalyst at high temperatures (680-800 °C) might be due to decomposition of the PdO y active phase into aggregated Pd 0 NPs. The Au-Pd-xCoO/3DOM Co 3 O 4 nanocatalysts exhibited better thermal stability and water tolerance ability compared to the 3DOM Co 3 O 4 -supported Au-Pd and Pd-CoO nanocatalysts. We believe that the supported Au-Pd-xCoO nanomaterials are promising catalysts in practical applications for organic combustion.

Three-dimensional (3D) ordered mesoporous Ag/MnO2 catalyst was prepared by impregnation method based on 3D-MnO2 and used for catalytic oxidation of HCHO. Ag nanoparticles are uniformly distributed on the polycrystalline wall of 3D-MnO2. The addition of Ag does not change the 3D ordered mesoporous structure of the Ag/MnO2, but does reduce the pore size and surface area. Ag nanoparticles provide sufficient active site for the oxidation reaction of HCHO, and Ag (111) crystal facets in the Ag/MnO2 are active faces. The 8.9% Ag/MnO2 catalyst shows a higher normalized rate (10.1 nmol·s(-1)·m(-2) at 110 °C) and TOF (0.007 s(-1) at 110 °C) under 1300 ppm of HCHO and 150 000 h(-1) of GHSV, and its apparent activation energy of the reaction is the lowest (39.1 kJ/mol). More Ag active sites, higher low-temperature reducibility, more abundant surface lattice oxygen species, oxygen vacancies, and lattice defects generated from interaction Ag with MnO2 are responsible for the excellent catalytic performance of HCHO oxidation on the 8.9% Ag/MnO2 catalyst. The 8.9% Ag/MnO2 catalyst remained highly active and stable under space velocity increasing from 60 000 to 150 000 h(-1), under initial HCHO concentration increasing from 500 to 1300 ppm, and under the presence of humidity, respectively.

Newly designed 3D highly ordered macro/mesoporous multifunctional La1-xCexCoO3 nanohybrid frameworks with a 2D hexagonal mesostructure were fabricated via facile meso-molding in a three-dimensionally macroporous perovskite (MTMP) route. The nanohybrid framework exhibited excellent catalytic activity for methane combustion, which derived from the MTMP providing a larger surface area and pore volume, uniform pore sizes, higher accessible surface oxygen concentration, better low-temperature reducibility, and a unique nanovoid 3D structure.

A series of novel metal-oxide-supported CeO(2) catalysts were prepared via the wet impregnation method, and their NH(3)-SCR activities were investigated. The Ce/TiO(2)-SiO(2) catalyst with a Ti/Si mass ratio of 3/1 exhibited superior NH(3)-SCR activity and high N(2) selectivity in the temperature range of 250-450 °C. The characterization results revealed that the activity enhancement was correlated with the properties of the support material. Cerium was highly dispersed on the TiO(2)-SiO(2) binary metal oxide support, and the interaction of Ti and Si resulted in greater conversion of Ce(4+) to Ce(3+) on the surface of the catalyst compared to that on the single metal oxide supports. As a result of in the increased number of acid sites on Ce/TiO(2)-SiO(2) that resulted from the addition of SiO(2), the NH(3) adsorption capacity was significantly improved. All of these factors played significant roles in the high SCR activity. More importantly, Ce/TiO(2)-SiO(2) exhibited strong resistance to SO(2) and H(2)O poisoning. After the addition of SiO(2), the number of Lewis-acid sites was not decreased, but the number of Brønsted-acid sites on the TiO(2)-SiO(2) carrier was increased. The introduction of SiO(2) further weakened the alkalinity over the surface of the Ce/TiO(2)-SiO(2) catalyst, which resulted in sulfate not easily accumulating on the surface of the Ce/TiO(2)-SiO(2) catalyst in comparison with Ce/TiO(2).

Co(1-x)M(x)Cr(2)O(4) (M = Li, Zr; x = 0-0.2) catalysts were prepared via the citric acid method and investigated for catalytic combustion of methane. Substitution at tetrahedral (A) sites with monovalent (Li) or tetravalent (Zr) metal ions led to a decrease or increase of the catalytic activity, respectively. The Co(0.95)Zr(0.05)Cr(2)O(4) catalyst proved to be the most active and its catalytic activity reached 90% of methane conversion at 448 °C, which dropped by 66 °C compared with that of the undoped CoCr(2)O(4) catalyst. XRD and Raman results indicated that lithium or zirconium substitution could modify the spinel structure and electronic properties. For lithium-doped catalysts, oxygen deficiency and a strong surface enrichment in lithium and chromium were detected. Zirconium substitution enhanced the reducibility of zirconium-doped catalysts and decreased the strength constant of both the Co-O band and the Cr-O band, which may contribute to the catalytic activity toward methane combustion. In addition, the prevalent catalytic combustion activity of the zirconium-substituted catalysts could be explained by their higher concentration of suprafacial, weakly chemisorbed oxygen.