Search

As the energy density of lithium-ion batteries (LIBs) increases, the shortened cycle life and the increased safety hazards of LIBs are drawing increasing concerns. To address such challenges, a series of localized high-concentration electrolytes (LHCEs) based on a solvating-solvent mixture of tetramethylene sulfone and trimethyl phosphate and a high flash-point diluent 1H,1H,5H-octafluoropentyl 1,1,2,2-tetrafluoroethyl ether were designed. The LHCEs exhibited nonflammability and greatly suppressed heat release at elevated temperatures, which would potentially improve the safety performance of the LIBs. Moreover, the optimal LHCE achieved capacity retentions of 87.1% and 81.7% in graphite||LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells after 500 cycles at 25 and 45 °C, respectively, which were significantly higher than the conventional electrolyte, whose capacity retentions were only 75.2% and 38.5% under the same conditions. Mechanistic studies revealed that the LHCE not only formed a more robust solid electrolyte interphase but also exhibited improved anodic stability, compared with the conventional electrolyte. This work sheds light on rational electrolyte design for high-energy density LIBs with high battery performance and low safety concerns.

Incorporation of pollutants, e.g., heavy metals, or critical elements, e.g., lithium, as impurities in mineral phases can significantly affect their mobility or sequestration in the environment. Even when present at low concentrations, impurities can alter the solubility and reactivity of the host mineral. In this study, we investigate the incorporation of trace amounts of iron (Fe 3+ ) and chromium (Cr 3+ ) during the crystal growth of the aluminum (Al 3+ ) hydroxide, gibbsite, a major component of bauxite ores, an important soil mineral, and a dominant mineral phase in stored radioactive wastes. Using a comprehensive suite of analytical techniques, we show that both Cr 3+ and Fe 3+ can be incorporated into the gibbsite lattice during coprecipitation by replacing Al 3+ in octahedral sites. These small amounts are consistent with limited to no structural isomorphism shared between Al 3+ and Cr 3+ /Fe 3+ hydroxide precipitates, nor room temperature miscibility of their isostructural M 2 O 3 oxide forms, in contrast with oxyhydroxide forms where Al 3+ and Fe 3+ share similar structural topologies. Despite the limited uptake of Cr 3+ /Fe 3+ , we show that these impurities have significant implications for gibbsite dissolution behavior. The limited uptake of Cr 3+ /Fe 3+ (e.g. 0.43% Cr 3+ and 0.4% Fe 3+ ), we show that these impurities have significant implications for gibbsite dissolution behavior and subsequent reactivity in complex environments.

Proton transfer is critically important to many electrocatalytic reactions, and directed proton delivery could open new avenues for the design of electrocatalysts. However, although this approach has been successful in molecular electrocatalysis, proton transfer has not received the same attention in heterogeneous electrocatalyst design. Here, we report that a metal oxide proton relay can be built within heterogeneous electrocatalyst architectures and improves the kinetics of electrochemical hydrogen evolution and oxidation reactions. The volcano-type relationship between activity enhancement and p K a of amine additives confirms this improvement; we observe maximum rate enhancement when the p K a of a proton relay matches the pH of the electrolyte solution. Density-functional-theory-based reactivity studies reveal a decreased proton transfer energy barrier with a metal oxide proton relay. These findings demonstrate the possibility of controlling the proton delivery and enhancing the reaction kinetics by tuning the chemical properties and structures at heterogeneous interfaces.

Atom trapping leads to catalysts with atomically dispersed Ru 1 O 5 sites on (100) facets of ceria, as identified by spectroscopy and DFT calculations. This is a new class of ceria-based materials with Ru properties drastically different from the known M/ceria materials. They show excellent activity in catalytic NO oxidation, a critical step that requires use of large loadings of expensive noble metals in diesel aftertreatment systems. Ru 1 /CeO 2 is stable during continuous cycling, ramping, and cooling as well as the presence of moisture. Furthermore, Ru 1 /CeO 2 shows very high NO x storage properties due to formation of stable Ru-NO complexes as well as a high spill-over rate of NO x onto CeO 2 . Only ∼0.05 wt % of Ru is required for excellent NO x storage. Ru 1 O 5 sites exhibit much higher stability during calcination in air/steam up to 750 °C in contrast to RuO 2 nanoparticles. We clarify the location of Ru(II) ions on the ceria surface and experimentally identify the mechanism of NO storage and oxidation using DFT calculations and in situ DRIFTS/mass spectroscopy. Moreover, we show excellent reactivity of Ru 1 /CeO 2 for NO reduction by CO at low temperatures: only 0.1-0.5 wt % of Ru is sufficient to achieve high activity. Modulation-excitation in situ infrared and XPS measurements reveal the individual elementary steps of NO reduction by CO on an atomically dispersed Ru ceria catalyst, highlighting unique properties of Ru 1 /CeO 2 and its propensity to form oxygen vacancies/Ce +3 sites that are critical for NO reduction, even at low Ru loadings. Our study highlights the applicability of novel ceria-based single-atom catalysts to NO and CO abatement.

Silicon is a high-capacity material for the anode of a rechargeable lithium-ion battery. One of the fundamental challenges for using Si in anodes is capacity fading, which has been revealed to be partially associated with the interfacial instability between the Si and liquid electrolyte due to the large volume swing of Si upon charging and discharging. Smart nanoscale design concepts, either presynthesized or formed in situ, have led to the mitigation of the detrimental factors associated with the volume swing of Si. However, it has never been clear how the chemical state of Si evolves and contributes to the capacity fading upon battery cycling. Here, we use cryo-electron energy loss spectroscopy to directly monitor, at a subnanometer scale, the chemical evolution of Si upon battery cycling. We discover that during the cycling process Si particles are progressively oxidized to form SiO 2 , which is initiated from the particle surface and gradually penetrates toward the interior of the particle, directly contributing to the capacity fading. Possible mechanisms of Si oxidation are postulated. We further show how the cycling stability can be improved by an electrolyte additive to form an effective passivation layer, representatively, even a small concentration of fluoroethylene carbonate causes the formation of an LiF layer on the Si nanoparticle surface that prevents Si oxidation and improves cycling stability. The present work unveils Si oxidation as a previously unrecognized factor that contributes to capacity fading, therefore providing insight into the design of anodes with Si-based materials.

Sulfurized polyacrylonitrile (SPAN) represents one of the most promising directions for high-energy-density lithium (Li)-sulfur batteries. However, the practical application of Li||SPAN is currently limited by the insufficient chemical/electrochemical stability of electrode/electrolyte interphase (EEI). Here, a pinned EEI layer is designed for stabilizing a SPAN cathode by regulating the EEI formation mechanism in an advanced LiFSI/ether/fluorinated-ether electrolyte. Computational simulations and experimental investigations reveal that, benefiting from the nonsolvating nature, the fluorinated-ether can not only act as a protective shield to prevent the Li polysulfides dissolution but also, more importantly, endow a diffusion-controlled EEI formation process. It promotes the formation of a uniform, protective, and conductive EEI layer pinning into SPAN surface region, enabling the high loading Li||SPAN batteries with superior cycling stability, wide temperature performance, and high-rate capability. This design strategy opens an avenue for exploring advanced electrolytes for Li||SPAN batteries and guides the interface design for broad types of battery systems.

The all-solid-state battery (ASSB) is a promising next-generation energy storage technology for both consumer electronics and electric vehicles because of its high energy density and improved safety. Sulfide solid-state electrolytes (SSEs) have merits of low density, high ionic conductivity, and favorable mechanical properties compared to oxide ceramic and polymer materials. However, mass production and processing of sulfide SSEs remain a grand challenge because of their poor moisture stability. Here, we report a reversible surface coating strategy for enhancing the moisture stability of sulfide SSEs using amphipathic organic molecules. An ultrathin layer of 1-bromopentane is coated on the sulfide SSE surface (e.g., Li 7 P 2 S 8 Br 0.5 I 0.5 ) via Van der Waals force. 1-Bromopentane has more negative adsorption energy with SSEs than H 2 O based on first-principles calculations, thereby enhancing the moisture stability of SSEs because the hydrophobic long-chain alkyl tail of 1-bromopentane repels water molecules. Moreover, this amphipathic molecular layer has a negligible effect on ionic conductivity and can be removed reversibly by heating at low temperatures (e.g., 160 °C). This finding opens a new pathway for the surface engineering of moisture-sensitive SSEs and other energy materials, thereby speeding up their deployment in ASSBs.

We present a novel anode interface modification on the β″-alumina solid-state electrolyte that improves the wetting behavior of molten sodium in battery applications. Heat treating a simple slurry, composed only of water, acetone, carbon black, and lead acetate, formed a porous carbon network decorated with PbO x (0 ≤ x ≤ 2) nanoparticles between 10 and 50 nm. Extensive performance analysis, through impedance spectroscopy and symmetric cycling, shows a stable, low-resistance interface for close to 6000 cycles. Furthermore, an intermediate temperature Na-S cell with a modified β″-alumina solid-state electrolyte could achieve an average stable cycling capacity as high as 509 mA h/g. This modification drastically decreases the amount of Pb content to approximately 3% in the anode interface (6 wt % or 0.4 mol %) and could further eliminate the need for toxic Pb altogether by replacing it with environmentally benign Sn. Overall, in situ reduction of oxide nanoparticles created a high-performance anode interface, further enabling large-scale applications of liquid metal anodes with solid-state electrolytes.

Despite cobalt (Co)-free/nickel (Ni)-rich layered oxides being considered as one of the promising cathode materials due to their high specific capacity, their highly reactive surface still hinders practical application. Herein, a polyimide/polyvinylpyrrolidone (PI/PVP, denoted as PP) coating layer is demonstrated as dual protection for the LiNi 0.96 Mg 0.02 Ti 0.02 O 2 (NMT) cathode material to suppress surface contamination against moist air and to prevent unwanted interfacial side reactions during cycling. The PP-coated NMT (PP@NMT) preserves a relatively clean surface with the bare generation of lithium residues, structural degradation, and gas evolution even after exposure to air with ∼30% humidity for 2 weeks compared to the bare NMT. In addition, the exposed PP@NMT significantly enhances the electrochemical performance of graphite||NMT cells by preventing byproducts and structural distortion. Moreover, the exposed PP@NMT achieves a high capacity retention of 86.7% after 500 cycles using an advanced localized high-concentration electrolyte. This work demonstrates promising protection of Co-free/Ni-rich layered cathodes for their practical usage even after exposure to moist air.

Perfluorobutyric acid (PFBA) is one type of perfluoroalkyl and polyfluoroalkyl substances (PFASs) and is widely used as an industrial compound. The removal of PFBA has attracted considerable scientific interests in recent decades because it causes environmental pollution and human diseases. Currently, the adsorption method has been used commonly to remove PFASs from wastewater. However, it is usually limited by the inevitable "secondary waste" produced in this treatment process. In this work, PFBA can be effectively removed by synergistic electrical switching ion exchange (ESIX) and a new type of nanostructured ion exchanger. Herein, the nanostructured ion exchanger has been designed and synthesized by coating a polypyrrole (PPy)@Fe 2 O 3 nanoneedle on carbon cloth (PPy@Fe 2 O 3 NN-CC). Results show that the PPy@Fe 2 O 3 NN-CC nanocomposite enhances ion exchange speed and efficiency, which ensures its high adsorption capacity and rapid regeneration property, thereby reducing secondary waste. Moreover, ESIX based on the PPy@Fe 2 O 3 NN-CC nanocomposite has high selectivity for adsorption of PFBA over other common anions in water, such as Cl - , SO 4 2- , and NO 3 - .

The COVID-19 pandemic has claimed millions of lives worldwide, sickened many more, and has resulted in severe socioeconomic consequences. As society returns to normal, understanding the spread and persistence of SARS CoV-2 on commonplace surfaces can help to mitigate future outbreaks of coronaviruses and other pathogens. We hypothesize that such an understanding can be aided by studying the binding and interaction of viral proteins with nonbiological surfaces. Here, we propose a methodology for investigating the adhesion of the SARS CoV-2 spike glycoprotein on common inorganic surfaces such as aluminum, copper, iron, silica, and ceria oxides as well as metallic gold. Quantitative adhesion was obtained from the analysis of measured forces at the nanoscale using an atomic force microscope operated under ambient conditions. Without imposing further constraints on the measurement conditions, our preliminary findings suggest that spike glycoproteins interact with similar adhesion forces across the majority of the metal oxides tested with the exception to gold, for which attraction forces ∼10 times stronger than all other materials studied were observed. Ferritin, which was used as a reference protein, was found to exhibit similar adhesion forces as SARS CoV-2 spike protein. This study results show that glycoprotein adhesion forces for similar ambient humidity, tip shape, and contact surface are nonspecific to the properties of metal oxide surfaces, which are expected to be covered by a thin water film. The findings suggest that under ambient conditions, glycoprotein adhesion to metal oxides is primarily controlled by the water capillary forces, and they depend on the surface tension of the liquid water. We discuss further strategies warranted to decipher the intricate nanoscale forces for improved quantification of the adhesion.

The criticality of cobalt (Co) has been motivating the quest for Co-free positive electrode materials for building lithium (Li)-ion batteries (LIBs). However, the LIBs based on Co-free positive electrode materials usually suffer from relatively fast capacity decay when coupled with conventional LiPF 6 -organocarbonate electrolytes. To address this issue, a 1,2-dimethoxyethane-based localized high-concentration electrolyte (LHCE) was developed and evaluated in a Co-free Li-ion cell chemistry (graphite||LiNi 0.96 Mg 0.02 Ti 0.02 O 2 ). Extraordinary capacity retentions were achieved with the LHCE in coin cells (95.3%), single-layer pouch cells (79.4%), and high-capacity loading double-layer pouch cells (70.9%) after being operated within the voltage range of 2.5-4.4 V for 500 charge/discharge cycles. The capacity retentions of counterpart cells using the LiPF 6 -based conventional electrolyte only reached 61.1, 57.2, and 59.8%, respectively. Mechanistic studies reveal that the superior electrode/electrolyte interphases formed by the LHCE and the intrinsic chemical stability of the LHCE account for the excellent electrochemical performance in the Co-free Li-ion cells.

The lithium (Li) metal polymer battery (LMPB) is a promising candidate for solid-state batteries with high safety. However, high voltage stability of such a battery has been hindered by the use of polyethylene oxide (PEO), which oxidizes at a potential lower than 4 V versus Li. Herein, we adopt the polymer-in-salt electrolyte (PISE) strategy to circumvent the disadvantage of the PEO-lithium bis(fluorosulfonyl)imide (LiFSI) system with EO/Li ≤ 8 through a dry ball-milling process to avoid the contamination of the residual solvent. The obtained solid-state PISEs exhibit distinctly different morphologies and coordination structures which lead to significant improvement in oxidative stability. P(EO) 1 LiFSI has a low melting temperature, a high ionic conductivity at 60 °C, and an oxidative stability of ∼4.5 V versus Li/Li + . With an effective interphase rich in inorganic species and a good stability of the hybrid polymer electrolyte toward Li metal, the LMPB constructed with Li||LiNi 1/3 Co 1/3 Mn 1/3 O 2 can retain 74.4% of capacity after 186 cycles at 60 °C under the cutoff charge voltage of 4.3 V. The findings offer a promising pathway toward high-voltage stable polymer electrolytes for high-energy-density and safe LMPBs.

Lithium-ion batteries (LIBs) with high-nickel (Ni) content LiNi x Mn y Co z O 2 ( x + y + z = 1) (NMC with Ni ≥ 0.6) cathodes operated at high charge voltages have been considered as one of the most promising candidates for addressing the challenge of increasing energy density demand. Conventional LiPF 6 -organocarbonate electrolytes exhibit incompatibility with such cell chemistries under certain testing conditions because of the instability of electrode/electrolyte interphases. In response to this challenge, ether-based electrolytes with finely tuned structure and composition of solvation sheaths were developed and evaluated in graphite (Gr)∥NMC811 cell chemistry in 2.5-4.4 V, despite ethers being conventionally considered to be unfavorable electrolyte solvents for LIBs because of their anodic instability above 4.0 V and cointercalation into Gr electrodes. The functional ether-based electrolytes in this work enable both excellent cycle life and high rate capability of Gr∥NMC811 cells. Mechanistic studies reveal that the unique structure and composition of the solvation sheath of the functional ether electrolytes are the main reasons behind their excellent anodic stability and effective protection of the Gr electrode and, consequently, the extraordinary cell performances when operated at high charge cutoff voltages. This work also provides a feasible approach in developing highly stable functional electrolytes for high-energy density LIBs.

The incorporation of relatively minor impurity metals onto metal (oxy)hydroxides can strongly impact solubility. In complex highly alkaline multicomponent radioactive tank wastes such as those at the Hanford Nuclear Reservation, tests indicate that the surface area-normalized dissolution rate of boehmite (γ-AlOOH) nanomaterials is at least an order of magnitude lower than that predicted for the pure phase. Here, we examine the dissolution kinetics of boehmite coated by adsorbed Cr(III), which adheres at saturation coverages as sparse chemisorbed monolayer clusters. Using 40 nm boehmite nanoplates as a model system, temperature-dependent dissolution rates of pure versus Cr(III)-adsorbed boehmite showed that the initial rate for the latter is consistently several times lower, with an apparent activation energy 16 kJ·mol -1 higher. Although the surface coverage is only around 50%, solution analysis coupled to multimethod solids characterization reveal a phyicochemical armoring effect by adsorbed Cr(III) that substantially reduces the number of dissolution-active sites on particle surfaces. Such findings could help improve kinetics models of boehmite and/or metal ion adsorbed boehmite nanomaterials, ultimately providing a stronger foundation for the development of more robust complex radioactive liquid waste processing strategies.

The amine-rich surfaces of pyrolyzed human solid waste (py-HSW) can be "primed" or "regenerated" with carbon dioxide (CO 2 ) to enhance their adsorption of ammonia (NH 3 ) for use as a soil amendment. To better understand the mechanism by which CO 2 exposure facilitates NH 3 adsorption to py-HSW, we artificially enriched a model sorbent, pyrolyzed, oxidized wood (py-ox wood) with amine functional groups through exposure to NH 3 . We then exposed these N-enriched materials to CO 2 and then resorbed NH 3 . The high heat of CO 2 adsorption ( Q st ) on py-HSW, 49 kJ mol -1 , at low surface coverage, 0.4 mmol CO 2 g -1 , showed that the naturally occurring N compounds in py-HSW have a high affinity for CO 2 . The Q st of CO 2 on py-ox wood also increased after exposure to NH 3 , reaching 50 kJ mol -1 at 0.7 mmol CO 2 g -1 , demonstrating that the incorporation of N-rich functional groups by NH 3 adsorption is favorable for CO 2 uptake. Adsorption kinetics of py-ox wood revealed continued, albeit diminishing NH 3 uptake after each CO 2 treatment, averaging 5.9 mmol NH 3 g -1 for the first NH 3 exposure event and 3.5 and 2.9 mmol NH 3 g -1 for the second and third; the electrophilic character of CO 2 serves as a Lewis acid, enhancing surface affinity for NH 3 uptake. Furthermore, penetration of 15 NH 3 and 13 CO 2 measured by NanoSIMS reached over 7 μm deep into both materials, explaining the large NH 3 capture. We expected similar NH 3 uptake in py-HSW sorbed with CO 2 and py-ox wood because both materials, py-HSW and py-ox wood sorbed with NH 3 , had similar N contents and similarly high CO 2 uptake. Yet NH 3 sorption in py-HSW was unexpectedly low, apparently from potassium (K) bicarbonate precipitation, reducing interactions between NH 3 and sorbed CO 2 ; 2-fold greater surface K in py-HSW was detected after exposure to CO 2 and NH 3 than before gas exposure. We show that amine-rich pyrolyzed waste materials have high CO 2 affinity, which facilitates NH 3 uptake. However, high ash contents as found in py-HSW hinder this mechanism., Competing Interests: The authors declare no competing financial interest., (Copyright © 2020 American Chemical Society.)

Intrinsic properties of a compound (e.g., electronic structure, crystallographic structure, optical and magnetic properties) define notably its chemical and physical behavior. In the case of nanomaterials, these fundamental properties depend on the occurrence of quantum mechanical size effects and on the considerable increase of the surface to bulk ratio. Here, we explore the size dependence of both crystal and electronic properties of CeO 2 nanoparticles (NPs) with different sizes by state-of-the art spectroscopic techniques. X-ray diffraction, X-ray photoelectron spectroscopy, and high-energy resolution fluorescence-detection hard X-ray absorption near-edge structure (HERFD-XANES) spectroscopy demonstrate that the as-synthesized NPs crystallize in the fluorite structure and they are predominantly composed of Ce IV ions. The strong dependence of the lattice parameter with the NPs size was attributed to the presence of adsorbed species at the NPs surface thanks to Fourier transform infrared spectroscopy and thermogravimetric analysis measurements. In addition, the size dependence of the t 2g states in the Ce L III XANES spectra was experimentally observed by HERFD-XANES and confirmed by theoretical calculations.

The development of advanced functional nanomaterials for selective adsorption in complex chemical environments requires partner studies of binding mechanisms. Motivated by observations of selective Cr(III) adsorption on boehmite nanoplates (γ-AlOOH) in highly caustic multicomponent solutions of nuclear tank waste, here we unravel the adsorption mechanism in molecular detail. We examined Cr(III) adsorption to synthetic boehmite nanoplates in sodium hydroxide solutions up to 3 M, using a combination of X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS), scanning/transmission electron microscopy (S/TEM), electron energy loss spectroscopy (EELS), high-resolution atomic force microscopy (HR-AFM), time-of-fight secondary ion mass spectrometry (ToF-SIMS), Cr K-edge X-ray absorption near edge structure (XANES)/extended X-ray absorption fine structure (EXAFS), and electron paramagnetic resonance (EPR). Adsorption isotherms and kinetics were successfully fit to Langmuir and pseudo-second-order kinetic models, respectively, consistent with monotonic uptake of Cr(OH) 4 - monomers until saturation coverage of approximately half the aluminum surface site density. High resolution AFM revealed monolayer cluster self-assembly on the (010) basal surfaces with increasing Cr(III) loading, possessing a structural motif similar to guyanaite (β-CrOOH), stabilized by corner-sharing Cr-O-Cr bonds and attached to the surface with edge-sharing Cr-O-Al bonds. The selective uptake appears related to short-range surface templating effects, with bridging metal connections likely enabled by hydroxyl anion ligand exchange reactions at the surface. Such a cluster formation mechanism, which stops short of more laterally extensive heteroepitaxy, could be a metal uptake discrimination mechanism more prevalent than currently recognized.

The electrolyte generally dictates the working temperature range of lithium-ion batteries (LIBs), thus developing a new class of electrolytes (primarily functional additives) in LIBs for wide temperature applications will be quite essential for further development of LIBs for the electric vehicle market. In this study, we develop new functional electrolytes containing multiple additives to enable the LIBs to perform well in a wide temperature range from -40 to 60 °C. Importantly, those cells based on the above optimized electrolytes have been proven to behave significantly enhanced discharging performance at -40 °C, the long-term cycling stability at 25 °C (more than 85% of capacity retention after 1000 cycles at 1C/1C rates in 1 Ah pouch cells), as well as the obviously improved cycling stability at 60 °C. These remarkable cell performances originate from the highly conductive, uniform, and compact passivating films formed on both anode and cathode surfaces by the synergistic effects of the multiple additives. Our finding on the synergistic benefits originating from a certain additive combination in the optimized electrolytes would favorably widen the working temperature range of future high-performance LIBs.

A simple and rapid process of ReO 4 - (as a surrogate of TcO 4 - ) removal from aqueous solutions based on the electrically switched ion exchange (ESIX) method has been demonstrated in this work. Activated carbon-Polypyrrole (AC-PPy) was synthesized from activated carbon and pyrrole by electrodeposition method which was served as an electrically switched ion exchanger for ReO 4 - removal. The characterization results show that the AC-PPy composite exhibited an excellent loading capacity and a high stability for ions uptake and release. Chronoamperometric studies show that the ESIX treatment could be completed within 60 s, demonstrating the rapid uptake and release of ions. Uptake and release of ReO 4 - was verified by electrochemical quartz crystal microbalance with dissipation shift (EQCMD) studies. By modulating the electrochemical potential of the AC-PPy, the uptake and release of ReO 4 - ions can be controlled. Similar trends of uptake and release of ReO 4 - were observed in cyclic voltammetry (-0.4 to 0.8 V) for five cycles with the EQCMD. X-ray photoelectron spectroscopy (XPS) confirmed the process of ReO 4 - removal in the AC-PPy composite. Conclusively, the smart material shows excellent efficiency and selectivity for the removal of ReO 4 - from aqueous solutions.

Here, Cr(VI) effects on Tc-immobilization by Fe(OH) 2 (s) are investigated while assessing Fe(OH) 2 (s) as a potential treatment method for Hanford low-activity waste destined for vitrification. Batch studies using simulated low-activity waste indicate that Tc(VII) and Cr(VI) removal is contingent on reduction to Tc(IV) and Cr(III). Furthermore, complete removal of both Cr and Tc depends on the amount of Fe(OH) 2 (s) present, where complete Cr and Tc removal requires more Fe(OH) 2 (s) (∼200 g/L of simulant), than removing Cr alone (∼50 g/L of simulant). XRD analysis suggests that Fe(OH) 2 (s) reaction and transformation in the simulant produces mostly goethite (α-FeOOH), where Fe(OH) 2 (s) transformation to goethite rather than magnetite is likely due to the simulant chemistry, which includes high levels of nitrite and other constituents. Once reduced, a fraction of Cr(III) and Tc(IV) substitute for octahedral Fe(III) within the goethite crystal lattice as supported by XPS, XANES, and/or EXAFS results. The remaining Cr(III) forms oxide and/or hydroxide phases, whereas Tc(IV) not fully incorporated into goethite persists as either adsorbed or partially incorporated Tc(IV)-oxide species. As such, to fully incorporate Tc(IV) into the goethite crystal structure, additional Fe(OH) 2 (s) (>200 g/L of simulant) may be required.

Understanding fundamental Tc chemistry is important to both the remediation of nuclear waste and the reprocessing of nuclear fuel; however, current knowledge of the electronic structure and spectral signatures of low-valent Tc compounds significantly lags behind the remainder of the d-block elements. In particular, identification and treatment of Tc speciation in legacy nuclear waste is challenging due to the lack of reference data especially for Tc compounds in the less common oxidation states (I-VI). In an effort to establish a spectroscopic library corresponding to the relevant conditions of extremely high ionic strength typical for the legacy nuclear waste, compounds with the general formula of [ fac-Tc(CO) 3 (OH 2 ) 3- n (OH) n ] 1- n (where n = 0-3) were examined by a range of spectroscopic techniques including 99 Tc/ 13 C NMR, IR, XPS, and XAS. In the series of monomeric aqua species, stepwise hydrolysis results in the increase of the Tc metal center electron density and corresponding progressive decrease of the Tc-C bond distances, Tc electron binding energies, and carbonyl stretching frequencies in the order [ fac-Tc(CO) 3 (OH 2 ) 3 ] + > [ fac-Tc(CO) 3 (OH 2 ) 2 (OH)] > [ fac-Tc(CO) 3 (OH 2 )(OH) 2 ] - . These results correlate with established trends of the 99 Tc upfield chemical shift and carbonyl 13 C downfield chemical shift. The lone exception is [ fac-Tc(CO) 3 (OH)] 4 which exhibits a comparatively low electron density at the metal center attributed to the μ 3 -bridging nature of the - OH ligands causing less σ-donation and no π-donation. This work also reports the first observations of these compounds by XPS and [ fac-Tc(CO) 3 Cl 3 ] 2- by XAS. The unique and distinguishable spectral features of the aqua [ fac-Tc(CO) 3 ] + complexes lay the foundation for their identification in the complex aqueous matrixes.

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of lithium (Li) metal batteries are systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) are chosen for this study and compared with the conventional LiPF 6 salt. Density functional theory calculations indicate that the chemical and electrochemical stabilities rank in the following order: LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiFSI-LiBOB. The experimental cycling stability of the Li metal batteries with the electrolytes ranks in the following order: LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiPF 6 > LiFSI-LiBOB, which is in well accordance with the calculation results. The LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. The key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high-performance Li metal batteries.

The development of highly active and cost-efficient electrocatalysts for the oxygen reduction reaction (ORR) is of great importance in a wide range of clean energy devices, including fuel cells and metal-air batteries. Herein, the simultaneous formation of Co 9 S 8 and N,S-codoped carbon with high ORR catalytic activity was achieved in an efficient strategy with a dual templates system. First, Co(OH) 2 nanosheets and tetraethyl orthosilicate were utilized to direct the formation of two-dimensional carbon precursors, which were then dispersed into thiourea solution. After subsequent pyrolysis and template removal, N,S-codoped porous carbon-sheet-confined Co 9 S 8 catalysts (Co 9 S 8 /NSC) were obtained. Owing to the morphological and compositional advantages as well as the synergistic effects, the resultant Co 9 S 8 /NSC catalysts with a modified doping level and pyrolysis degree exhibit superior ORR catalytic activity and long-term stability compared with the state-of-the-art Pt/C catalysts in alkaline media. Remarkably, the as-prepared carbon composites also reveal exceptional tolerance of methanol, indicating their potential applications in fuel cells.

Technetium (Tc) remains a priority remediation concern due to persistent challenges, including mobilization due to rapid reoxidation of immobilized Tc, and competing comingled contaminants, e.g., Cr(VI), that inhibit Tc(VII) reduction and incorporation into stable mineral phases. Here Fe(OH) 2 (s) is investigated as a comprehensive solution for overcoming these challenges, by serving as both the reductant, (Fe(II)), and the immobilization agent to form Tc-incorporated magnetite (Fe 3 O 4 ). Trace metal analysis suggests removal of Tc(VII) and Cr(VI) from solution occurs simultaneously; however, complete removal and reduction of Cr(VI) is achieved earlier than the removal/reduction of comingled Tc(VII). Bulk oxidation state analysis of the final magnetite solid phase by XANES shows that the majority of Tc is Tc(IV), which is corroborated by XPS measurements. Furthermore, EXAFS results show successful, albeit partial, Tc(IV) incorporation into magnetite octahedral sites. Cr XPS analysis indicates reduction to Cr(III) and the formation of a Cr-incorporated spinel, Cr 2 O 3 , and Cr(OH) 3 phases. Spinel (modeled as Fe 3 O 4 ), goethite (α-FeOOH), and feroxyhyte (δ-FeOOH) are detected in all reacted final solid phase samples analyzed by XRD. Incorporation of Tc(IV) has little effect on the spinel lattice structure. Reaction of Fe(OH) 2 (s) in the presence of Cr(III) results in the formation of a spinel phase that is a solid solution between magnetite (Fe 3 O 4 ) and chromite (FeCr 2 O 4 ).

Instability of carbon-based oxygen electrodes and incomplete decomposition of Li 2 CO 3 during charge process are critical barriers for rechargeable Li-O 2 batteries. Here we report the complete decomposition of Li 2 CO 3 in Li-O 2 batteries using the ultrafine iridium-decorated boron carbide (Ir/B 4 C) nanocomposite as a noncarbon based oxygen electrode. The systematic investigation on charging the Li 2 CO 3 preloaded Ir/B 4 C electrode in an ether-based electrolyte demonstrates that the Ir/B 4 C electrode can decompose Li 2 CO 3 with an efficiency close to 100% at a voltage below 4.37 V. In contrast, the bare B 4 C without Ir electrocatalyst can only decompose 4.7% of the preloaded Li 2 CO 3 . Theoretical analysis indicates that the high efficiency decomposition of Li 2 CO 3 can be attributed to the synergistic effects of Ir and B 4 C. Ir has a high affinity for oxygen species, which could lower the energy barrier for electrochemical oxidation of Li 2 CO 3 . B 4 C exhibits much higher chemical and electrochemical stability than carbon-based electrodes and high catalytic activity for Li-O 2 reactions. A Li-O 2 battery using Ir/B 4 C as the oxygen electrode material shows highly enhanced cycling stability than those using the bare B 4 C oxygen electrode. Further development of these stable oxygen-electrodes could accelerate practical applications of Li-O 2 batteries.

The corrosion of aluminum current collectors and the oxidation of solvents at a relatively high potential have been widely investigated with an aim to stabilize the electrochemical performance of lithium-ion batteries using such components. The corrosion behavior of aluminum current collectors was revisited using a home-build high-precision electrochemical measurement system, and the impact of electrolyte components and the surface protection layer on aluminum foil was systematically studied. The electrochemical results showed that the corrosion of aluminum foil was triggered by the electrochemical oxidation of solvent molecules, like ethylene carbonate, at a relative high potential. The organic radical cations generated from the electrochemical oxidation are energetically unstable and readily undergo a deprotonation reaction that generates protons and promotes the dissolution of Al 3+ from the aluminum foil. This new reaction mechanism can also shed light on the dissolution of transitional metal at high potentials.

Rational design and construction of Pt-based porous nanostructures with large mesopores have triggered significant considerations because of their high surface area and more efficient mass transport. Hydrochloric acid-induced kinetically controlled reduction of metal precursors in the presence of soft template F-127 and hard template tellurium nanowires has been successfully demonstrated to construct one-dimensional hierarchical porous PtCu alloy nanostructures with large mesopores. Moreover, the electrochemical experiments demonstrated that the PtCu hierarchically porous nanostructures synthesized under optimized conditions exhibit enhanced electrocatalytic performance for oxygen reduction reaction in acid media.

We report the results of a VAMAS (Versailles Project on Advanced Materials and Standards) inter-laboratory study on the measurement of the shell thickness and chemistry of nanoparticle coatings. Peptide-coated gold particles were supplied to laboratories in two forms: a colloidal suspension in pure water and; particles dried onto a silicon wafer. Participants prepared and analyzed these samples using either X-ray photoelectron spectroscopy (XPS) or low energy ion scattering (LEIS). Careful data analysis revealed some significant sources of discrepancy, particularly for XPS. Degradation during transportation, storage or sample preparation resulted in a variability in thickness of 53 %. The calculation method chosen by XPS participants contributed a variability of 67 %. However, variability of 12 % was achieved for the samples deposited using a single method and by choosing photoelectron peaks that were not adversely affected by instrumental transmission effects. The study identified a need for more consistency in instrumental transmission functions and relative sensitivity factors, since this contributed a variability of 33 %. The results from the LEIS participants were more consistent, with variability of less than 10 % in thickness and this is mostly due to a common method of data analysis. The calculation was performed using a model developed for uniform, flat films and some participants employed a correction factor to account for the sample geometry, which appears warranted based upon a simulation of LEIS data from one of the participants and comparison to the XPS results.

Nitrous acid (HONO) accumulates in the nocturnal boundary layer where it is an important source of daytime hydroxyl radicals. Although there is clear evidence for the involvement of heterogeneous reactions of NO2 on surfaces as a source of HONO, mechanisms remain poorly understood. We used coated-wall flow tube measurements of NO2 reactivity on environmentally relevant surfaces (Fe (hydr)oxides, clay minerals, and soil from Arizona and the Saharan Desert) and detailed mineralogical characterization of substrates to show that reduction of NO2 by Fe-bearing minerals in soil can be a more important source of HONO than the putative NO2 hydrolysis mechanism. The magnitude of NO2-to-HONO conversion depends on the amount of Fe(2+) present in substrates and soil surface acidity. Studies examining the dependence of HONO flux on substrate pH revealed that HONO is formed at soil pH < 5 from the reaction between NO2 and Fe(2+)(aq) present in thin films of water coating the surface, whereas in the range of pH 5-8 HONO stems from reaction of NO2 with structural iron or surface complexed Fe(2+) followed by protonation of nitrite via surface Fe-OH2(+) groups. Reduction of NO2 on ubiquitous Fe-bearing minerals in soil may explain HONO accumulation in the nocturnal boundary layer and the enhanced [HONO]/[NO2] ratios observed during dust storms in urban areas.

Spectral modeling of photoelectrons can serve as a valuable tool when combined with X-ray photoelectron spectroscopy (XPS) analysis. Herein, a new version of the NIST Simulation of Electron Spectra for Surface Analysis (SESSA 2.0) software, capable of directly simulating spherical multilayer NPs, was applied to model citrate stabilized Au/Ag-core/shell nanoparticles (NPs). The NPs were characterized using XPS and scanning transmission electron microscopy (STEM) to determine the composition and morphology of the NPs. The Au/Ag-core/shell NPs were observed to be polydispersed in size, nonspherical, and contain off-centered Au-cores. Using the average NP dimensions determined from STEM analysis, SESSA spectral modeling indicated that washed Au/Ag-core-shell NPs were stabilized with a 0.8 nm layer of sodium citrate and a 0.05 nm (one wash) or 0.025 nm (two wash) layer of adventitious hydrocarbon, but did not fully account for the observed XPS signal from the Au-core. This was addressed by a series of simulations and normalizations to account for contributions of NP nonsphericity and off-centered Au-cores. Both of these nonuniformities reduce the effective Ag-shell thickness, which effect the Au-core photoelectron intensity. The off-centered cores had the greatest impact for the particles in this study. When the contributions from the geometrical nonuniformities are included in the simulations, the SESSA generated elemental compositions that matched the XPS elemental compositions. This work demonstrates how spectral modeling software such as SESSA, when combined with experimental XPS and STEM measurements, advances the ability to quantitatively assess overlayer thicknesses for multilayer core-shell NPs and deal with complex, nonideal geometrical properties.

The effects of propylene carbonate (PC) content in CsPF6-containing electrolytes on the performances of graphite electrode in lithium half cells and in graphite∥LiNi0.80Co0.15Al0.05O2 (NCA) full cells are investigated. It is found that the performance of graphite electrode is significantly affected by PC content in the CsPF6-containing electrolytes. An optimal PC content of 20% by weight in the solvent mixtures is identified. The enhanced electrochemical performance of graphite electrode can be attributed to the synergistic effects of the PC solvent and the Cs(+) additive. The synergistic effects of Cs(+) additive and appropriate amount of PC enable the formation of a robust, ultrathin, and compact solid electrolyte interphase (SEI) layer on the surface of graphite electrode, which is only permeable for desolvated Li(+) ions and allows fast Li(+) ion transport through it. Therefore, this SEI layer effectively suppresses the PC cointercalation and largely alleviates the Li dendrite formation on graphite electrode during lithiation even at relatively high current densities. The presence of low-melting-point PC solvent improves the sustainable operation of graphite∥NCA full cells under a wide temperature range. The fundamental findings also shed light on the importance of manipulating/maintaining the electrode/electrolyte interphasial stability in various energy-storage devices.

Despite the potential advantages it brings, such as wider liquid range and lower cost, propylene carbonate (PC) is seldom used in lithium-ion batteries because of its sustained cointercalation into the graphene structure and the eventual graphite exfoliation. Here, we report that cesium cation (Cs(+)) directs the formation of solid electrolyte interphase on graphite anode in PC-rich electrolytes through its preferential solvation by ethylene carbonate (EC) and the subsequent higher reduction potential of the complex cation. Effective suppression of PC-decomposition and graphite-exfoliation is achieved by adjusting the EC/PC ratio in electrolytes to allow a reductive decomposition of Cs(+)-(EC)m (1 ≤ m ≤ 2) complex preceding that of Li(+)-(PC)n (3 ≤ n ≤ 5). Such Cs(+)-directed interphase is stable, ultrathin, and compact, leading to significant improvement in battery performances. In a broader context, the accurate tailoring of interphasial chemistry by introducing a new solvation center represents a fundamental breakthrough in manipulating interfacial reactions that once were elusive to control.

The garnet structure has been proposed as a potential crystalline nuclear waste form for accommodation of actinide elements, especially uranium (U). In this study, yttrium iron garnet (YIG) as a model garnet host was studied for the incorporation of U analogs, cerium (Ce) and thorium (Th), incorporated by a charge-coupled substitution with calcium (Ca) for yttrium (Y) in YIG, namely, 2Y(3+) = Ca(2+) + M(4+), where M(4+) = Ce(4+) or Th(4+). Single-phase garnets Y3-xCa0.5xM0.5xFe5O12 (x = 0.1-0.7) were synthesized by the citrate-nitrate combustion method. Ce was confirmed to be tetravalent by X-ray absorption spectroscopy and X-ray photoelectron spectroscopy. X-ray diffraction and (57)Fe-Mössbauer spectroscopy indicated that M(4+) and Ca(2+) cations are restricted to the c site, and the local environments of both the tetrahedral and the octahedral Fe(3+) are systematically affected by the extent of substitution. The charge-coupled substitution has advantages in incorporating Ce/Th and in stabilizing the substituted phases compared to a single substitution strategy. Enthalpies of formation of garnets were obtained by high temperature oxide melt solution calorimetry, and the enthalpies of substitution of Ce and Th were determined. The thermodynamic analysis demonstrates that the substituted garnets are entropically rather than energetically stabilized. This suggests that such garnets may form and persist in repositories at high temperature but might decompose near room temperature.

Suppressing lithium (Li) dendrite growth is one of the most critical challenges for the development of Li metal batteries. Here, we report for the first time the growth of dendrite-free lithium films with a self-aligned and highly compacted nanorod structure when the film was deposited in the electrolyte consisting of 1.0 M LiPF6 in propylene carbonate with 0.05 M CsPF6 as an additive. Evolution of both the surface and the cross-sectional morphologies of the Li films during repeated Li deposition/stripping processes were systematically investigated. It is found that the formation of the compact Li nanorod structure is preceded by a solid electrolyte interphase (SEI) layer formed on the surface of the substrate. Electrochemical analysis indicates that an initial reduction process occurred at ∼ 2.05 V vs Li/Li(+) before Li deposition is responsible for the formation of the initial SEI, while the X-ray photoelectron spectroscopy indicates that the presence of CsPF6 additive can largely enhance the formation of LiF in this initial SEI. Hence, the smooth Li deposition in Cs(+)-containing electrolyte is the result of a synergistic effect of Cs(+) additive and preformed SEI layer. A fundamental understanding on the composition, internal structure, and evolution of Li metal films may lead to new approaches to stabilize the long-term cycling stability of Li metal and other metal anodes for energy storage applications.

The long-term operation of Li-O2 batteries under full discharge/charge conditions is investigated in a glyme-based electrolyte. The formation of stable interfacial layer on the electrode surface during the initial cycling stabilizes reaction products at subsequent cycling stages as demonstrated by quantitative analyses of the discharge products and the gases released during charging. There is a quick switch from the predominant formation of Li2O2 to the predominant formation of side products during the first few cycles. However, after the formation of the stable interfacial layer, the yield of Li2O2 in the reaction products is stabilized at about 33-40%. Extended cycling under full discharge/charge conditions is achievable upon selection of appropriate electrode materials (carbon source and catalyst) and cycling protocol. Further investigation on the interfacial layer, which in situ forms on air electrode, may increase the long-term yield of Li2O2 during the cycling and enable highly reversible Li-O2 batteries required for practical applications.

Water reduction under two different visible-light ranges (λ > 400 nm and λ > 435 nm) was investigated in gold-loaded titanium dioxide (Au-TiO2) heterostructures with different sizes of Au nanoparticles (NPs). Our study clearly demonstrates the essential role played by Au NP size in plasmon-driven H2O reduction and reveals two distinct mechanisms to clarify visible-light photocatalytic activity under different excitation conditions. The size of the Au NP governs the efficiency of plasmon-mediated electron transfer and plays a critical role in determining the reduction potentials of the electrons transferred to the TiO2 conduction band. Our discovery provides a facile method of manipulating photocatalytic activity simply by varying the Au NP size and is expected to greatly facilitate the design of suitable plasmonic photocatalysts for solar-to-fuel energy conversion.

A hydrogen-evolving homogeneous Ni(P2N2)2 electrocatalyst with peripheral ester groups has been covalently attached to a 1,2,3-triazolyllithium-terminated planar glassy carbon electrode surface. Coupling proceeds with both the Ni(0) and the Ni(II) complexes. X-ray photoemission spectra show excellent agreement between the Ni(0) coupling product and its parent complex, and voltammetry of the surface-confined system shows that a single species predominates with a surface density of 1.3 × 10(-10) mol cm(-2), approaching the value estimated for a densely packed monolayer. With the Ni(II) system, both photoemission and voltammetric data show speciation to unidentified products on coupling, and the surface density is 6.7 × 10(-11) mol cm(-2). The surface-confined Ni(0) complex is an electroctalyst for hydrogen evolution, showing the onset of catalytic current at the same potential as the soluble parent complex. Decomposition of the surface-confined species is observed in acidic acetonitrile. This is interpreted to reflect the lability of the Ni(II)-phosphine interaction and the basicity of the free phosphine and bears on concurrent efforts to implement surface-confined Ni(P2N2)2 complexes in electrochemical or photoelectrochemical devices.

Our previous study showed that formation of TcS2-like phases is favored over TcO2 under sulfidic conditions stimulated by nano zerovalent iron. This study further investigates the stability of Tc(IV) sulfide upon reoxidation by solution chemistry, solid phase characterization, and X-ray absorption spectroscopy. Tc dissolution data showed that Tc(VII) reduced by sulfide-transformed nZVI has substantially slower reoxidation kinetics than Tc(VII) reduced by nZVI only. The initial inhibition of Tc(IV) dissolution at S/Fe = 0.112 is due to the redox buffer capacity of FeS, which is evidenced by the parallel trends in oxidation-reduction potentials (ORP) and Tc dissolution kinetics. The role of FeS in inhibiting Tc oxidation is further supported by the Mössbauer spectroscopy and micro X-ray diffraction data at S/Fe = 0.112, showing persistence of FeS after 24-h oxidation but complete oxidation after 120-h oxidation. X-ray absorption spectroscopy data for S/Fe = 0.011 showed significantly increasing percentages of TcS2 in the solid phase after 24-h oxidation, indicating stronger resistance of TcS2 to oxidation. At S/Fe = 0.112, the XAS results revealed significant transformation of Tc speciation from TcS2 to TcO2 after 120-h oxidation. Given that no apparent Tc dissolution occurred during this period, the speciation transformation might play a secondary role in hindering Tc oxidation. Collectively, the results indicate that sequestrating Tc as TcS2 under stimulated sulfate reduction is a promising strategy to improve the long-term stability of reduced Tc in subsurface remediation.

Lithium-sulfur (Li-S) battery is one of the most promising energy storage systems because of its high specific capacity of 1675 mAh g(-1) based on sulfur. However, the rapid capacity degradation, mainly caused by polysulfide dissolution, remains a significant challenge prior to practical applications. This work demonstrates that a novel Ni-based metal organic framework (Ni-MOF), Ni6(BTB)4(BP)3 (BTB = benzene-1,3,5-tribenzoate and BP = 4,4'-bipyridyl), can remarkably immobilize polysulfides within the cathode structure through physical and chemical interactions at molecular level. The capacity retention achieves up to 89% after 100 cycles at 0.1 C. The excellent performance is attributed to the synergistic effects of the interwoven mesopores (∼2.8 nm) and micropores (∼1.4 nm) of Ni-MOF, which first provide an ideal matrix to confine polysulfides, and the strong interactions between Lewis acidic Ni(II) center and the polysulfide base, which significantly slow down the migration of soluble polysulfides out of the pores, leading to the excellent cycling performance of Ni-MOF/S composite.

Hydrogenase enzymes use first-row transition metals to interconvert H2 with protons and electrons, reactions that are important for the storage and recovery of energy from intermittent sources such as solar, hydroelectric, and wind. Here we present Ni(P(Cy)2N(Gly)2)2, a water-soluble molecular electrocatalyst with the amino acid glycine built into the diphosphine ligand framework. Proton transfer between the outer coordination sphere carboxylates and the second coordination sphere pendant amines is rapid, as observed by cyclic voltammetry and FTIR spectroscopy, indicating that the carboxylate groups may participate in proton transfer during catalysis. This complex oxidizes H2 (1-33 s(-1)) at low overpotentials (150-365 mV) over a range of pH values (0.1-9.0) and produces H2 under identical solution conditions (>2400 s(-1) at pH 0.5). Enzymes employ proton channels for the controlled movement of protons over long distances-the results presented here demonstrate the effects of a simple two-component proton channel in a synthetic molecular electrocatalyst.

The reaction of a lithium acetylide-ethylenediamine complex with azide-terminated glassy carbon surfaces affords 1,2,3-triazolyllithium surface groups that are active toward covalent C-C coupling reactions, including salt metathesis with an aliphatic halide and nucleophilic addition at an aldehyde. Surface ferrocenyl groups were introduced by reaction with (6-iodohexyl)ferrocene; the voltammetry of electrode samples shows narrow, symmetric peaks indicating uniform attachment. X-ray photoelectron and reflectance infrared spectroscopic data provide further support for the surface-attached products. Formation of the 1,2,3-triazolyllithium linkage requires neither a catalyst nor a strained alkyne. Coverages obtained by this route are similar to those obtained by the more common Cu(I)-catalyzed alkyne-azide coupling (CuAAC) of ethynylferrocene with surface azides. Preconditioning of the glassy carbon disk electrodes at ambient temperature under nitrogen affords coverages comparable to those reported with preconditioning at 1000 °C under hydrogen/nitrogen.

Under anoxic conditions, soluble pertechnetate (⁹⁹TcO₄⁻) can be reduced to less soluble TcO₂·nH₂O, but the oxide is highly susceptible to reoxidation. Here we investigate an alternative strategy for remediation of Tc-contaminated groundwater whereby sequestration as Tc sulfide is favored by sulfidic conditions stimulated by nano zerovalent iron (nZVI). nZVI was pre-exposed to increasing concentrations of sulfide in simulated Hanford groundwater for 24 h to mimic the onset of aquifer biotic sulfate reduction. Solid-phase characterizations of the sulfidated nZVI confirmed the formation of nanocrystalline FeS phases, but higher S/Fe ratios (>0.112) did not result in the formation of significantly more FeS. The kinetics of Tc sequestration by these materials showed faster Tc removal rates with increasing S/Fe between 0 and 0.056, but decreasing Tc removal rates with S/Fe > 0.224. The more favorable Tc removal kinetics at low S/Fe could be due to a higher affinity of TcO₄⁻ for FeS than iron oxides, and electron microscopy confirmed that the majority of the Tc was associated with FeS phases. The inhibition of Tc removal at high S/Fe appears to have been caused by excess HS(-). X-ray absorption spectroscopy revealed that as S/Fe increased, the pathway for Tc(IV) formation shifted from TcO₂·nH2₂ to Tc sulfide phases. The most substantial change of Tc speciation occurred at low S/Fe, coinciding with the rapid increase in Tc removal rate. This agreement further confirms the importance of FeS in Tc sequestration.

Rechargeable lithium metal batteries are considered the "Holy Grail" of energy storage systems. Unfortunately, uncontrollable dendritic lithium growth inherent in these batteries (upon repeated charge/discharge cycling) has prevented their practical application over the past 40 years. We show a novel mechanism that can fundamentally alter dendrite formation. At low concentrations, selected cations (such as cesium or rubidium ions) exhibit an effective reduction potential below the standard reduction potential of lithium ions. During lithium deposition, these additive cations form a positively charged electrostatic shield around the initial growth tip of the protuberances without reduction and deposition of the additives. This forces further deposition of lithium to adjacent regions of the anode and eliminates dendrite formation in lithium metal batteries. This strategy may also prevent dendrite growth in lithium-ion batteries as well as other metal batteries and transform the surface uniformity of coatings deposited in many general electrodeposition processes.

Sub-15 nm Au nanoparticles have been fabricated on a nanostructured Ag surface at room temperature via a liquid-phase chemical deposition upon excitation of the localized surface plasmon resonance (SPR). Measurement of the SPR-mediated photothermal local heating of the substrate surface by a molecular thermometry strategy indicated the temperature to be above 230 °C, which led to an efficient decomposition of CH(3)AuPPh(3) to form Au nanoparticles on the Ag surface. Particle sizes were tunable between 3 and 10 nm by adjusting the deposition time. A surface-limited growth model for Au nanoparticles on Ag is consistent with the deposition kinetics.

Aqueous Fe(II) reacts with Fe(III) oxides by coupled electron transfer and atom exchange (ETAE) resulting in mineral recrystallization, contaminant reduction, and trace element cycling. Previous studies of Fe(II)-Fe(III) ETAE have explored the reactivity of either pure iron oxide phases or those containing small quantities of soluble trace elements. Naturally occurring iron oxides, however, contain substantial quantities of insoluble impurities (e.g., Al) which are known to affect the chemical properties of such minerals. Here we explore the effect of Al(III), Cr(III), and Sn(IV) substitution (1-8 mol %) on trace element release from Ni(II)-substituted goethite and Zn(II)-substituted hematite during reaction with aqueous Fe(II). Fe(II)-activated trace element release is substantially inhibited from both minerals when an insoluble element is cosubstituted into the structure, and the total amount of release decreases exponentially with increasing cosubstituent. The limited changes in surface composition that occur following reaction with Fe(II) indicate that Al, Cr, and Sn do not exsolve from the structure and that Ni and Zn released to solution originate primarily from the bulk rather than the particle exterior (upper ~3 nm). Incorporation of Al into goethite substantially decreases the amount of iron atom exchange with aqueous Fe(II) and, consequently, the amount of Ni release from the structure. This implies that trace element release inhibition caused by substituting insoluble elements results from a decrease in the amount of mineral recrystallization. These results suggest that naturally occurring iron oxides containing insoluble elements are less susceptible to Fe(II)-activated recrystallization and exhibit a greater retention of trace elements and contaminants than pure mineral phases.

The understanding of the atomic-scale structural and chemical ordering in supported nanosized alloy particles is fundamental for achieving active catalysts by design. This report shows how such knowledge can be obtained by a combination of techniques including X-ray photoelectron spectroscopy and synchrotron radiation based X-ray fine structure absorption spectroscopy and high-energy X-ray diffraction coupled to atomic pair distribution function analysis, and how the support-nanoalloy interaction influences the catalytic activity of ternary nanoalloy (platinum-nickel-cobalt) particles on three different supports: carbon, silica, and titania. The reaction of carbon monoxide with oxygen is employed as a probe to the catalytic activity. The thermochemical processing of this ternary composition, in combination with the different support materials, is demonstrated to be capable of fine-tuning the catalytic activity and stability. The support-nanoalloy interaction is shown to influence structural and chemical ordering in the nanoparticles, leading to support-tunable active sites on the nanoalloys for oxygen activation in the catalytic oxidation of carbon monoxide. A nickel/cobalt-tuned catalytic site on the surface of nanoalloy is revealed for oxygen activation, which differs from the traditional oxygen-activation sites known for oxide-supported noble metal catalysts. The discovery of such support-nanoalloy interaction-enabled oxygen-activation sites introduces a very promising strategy for designing active catalysts in heterogeneous catalysis.

U(VI) doped hematite was synthesized and exposed to two different organic reductants with E(0) of 0.23 and 0.70 V. A combination of HAADF-TEM and EXAFS provided evidence that uranium was incorporated in hematite in uranate, likely octahedral coordination. XPS indicated that structurally incorporated U(VI) was reduced to U(V), whereas non-incorporated U(VI) was reduced to U(IV). Specifically, the experiments indicate that U(V) was the dominant oxidation state of uranium in hematite around Eh -0.24 to -0.28 V and pH 7.7-8.6 for at least up to 5 weeks of reaction time. U(V), but not U(IV), was also detected in hematite at Eh +0.21 V (pH 7.1-7.3). The results support the hypothesis, based on previous experimental and theoretical work, that the stability field of U(V) is widened relative to U(IV) and U(VI) in uranate coordination environments where the coordination number of U is less than 8.

The oxidation state switching of cerium in cerium oxide nanoparticles is studied in detail. The influence of synthesis medium, aging time and local environment on the oxidation state switching, between +3 and + 4, is analyzed by tracking the absorption edge using UV-Visible spectroscopy. It is observed that by tuning the local environment, the chemistry of the nanoparticles could be altered. These time dependent, environmentally induced changes likely contribute to inconsistencies in the literature regarding quantum-confinement effects for ceria nanoparticles. The results in this article indicate that there is a need to carry out comprehensive analysis of nanoparticles while considering the influence of synthesis and processing conditions, aging time and local environment.

Nanocrystalline WO(3) thin films were produced by sputter-deposition by varying the ratio of argon to oxygen in the reactive gas mixture during deposition. The surface chemistry, physical characteristics, and optical properties of nanocrystalline WO(3) films were evaluated using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray reflectivity (XRR), and spectrophotometric measurements. The effect of ultramicrostructure was significant on the optical properties of WO(3) films. The XPS analyses indicate the formation of stoichiometric WO(3) with tungsten existing in fully oxidized valence state (W(6+)). However, WO(3) films grown at high oxygen concentration (>60%) in the sputtering gas mixture were over stoichiometric with excess oxygen. XRR simulations based on isotropic WO(3) film-SiO(2) interface-Si substrate modeling indicate that the density of WO(3) films is sensitive to the oxygen content in the sputtering gas. The spectral transmission of the films increased with increasing oxygen. The band gap of these films increases from 2.78 to 3.25 eV with increasing oxygen. A direct correlation between the film density and band gap in nanocrystalline WO(3) films is established on the basis of the observed results., (© 2012 American Chemical Society)